Hotpoint-Ariston HBRZA50 User Manual

FREEZER - MODELS RZA50

INSTRUCTIONS FOR INSTALLATION & USE

GETTING STARTED:

STEP 1

Choose a location for your

freezer,away from any

heat sources and

allow adequate

ventilation - 100mm

(4 inches) gap above.

STEP 3

Level the freezer by
adjusting the front feet.
This will stop rocking or

vibration and keep the

NB.The spanner is for illustration

only and is not supplied with the

STEP 5

Before plugging in and
switching on, leave the

door aligned.

freezer.

freezer in its final

location for at least 15

minutes to allow it to

settle.

To ensure that your freezer runs reliably and efficiently follow these steps.

STEP 2

Move the freezer into
position, using the sides
of the cabinet. Take care
to avoid damaging the
refrigerant circuit pipe
work on the rear.

STEP 4

After the front feet have
been adjusted and the
freezer is level, fit the left
and right hand bottom
hinge covers supplied.
Align with the cover
plate slots and push into
position.

STEP 6

Plug in and switch on.
Allow the freezer to cool
before placing food
inside.

All food in the freezer
should be covered.

INSTALLATION

SAFETY &

CONTROLS USEFUL ADVICE

MAINTENANCE

CLEANING &

TROUBLESHOOTING

STEP 7

If you are freezing fresh

food,turn ON fast freeze

by pressing the switch 24

hours before placing the

food inside.Place the

fresh food inside.

Remember to turn fast freeze OFF

after 24 hours.

STEP 8

Your freezer is now
working.
If after 24 hours your
freezer is not operating
as you want, refer to the
TROUBLESHOOTING
section.

Read the rest of these instructions to get the best from your appliance

and remember to fill in your guarantee registration.

Keep this Book in a safe place for quick reference.

GUARANTEE

SERVICE &

For Your Safety

For your safety, read the following advice:

The freezer cooling system contains a small amount of gas which is environmentally
friendly but flammable. To avoid any risk :-

● Install the freezer following the installation instructions and ensure that

ventilation openings are kept clear of obstruction.

● Take care when installing or moving the freezer to avoid damaging the pipes

on the rear.

● If you suspect a leak, do not switch on the freezer,but open the windows and

doors to ventilate the room.

● Do not use any electrical devices inside the freezer, for instance for

SAFETY &

INSTALLATION

● Do not use any mechanical devices for defrosting other than any which may

● Only use this freezer for storing domestic foodstuffs.

When installing your freezer :-

● Ensure that the mains cable is not trapped underneath or behind the freezer

● Do not stack any other appliance on top of this freezer as they may

defrosting.

have been supplied with the freezer as they may cause damage.

when you install or move it.

damage the freezer or become unstable.

When using your freezer :-

● Do not sit or stand on top of your freezer.

● Do not store poisonous, flammable or dangerous substances in your freezer.

● Do not use aerosol sprays for defrosting or cleaning your freezer.

If you sell the freezer, pass on this booklet to the new owner.

2

Installation

Location & Air Circulation

100mm
(4 inches)

Locate your freezer away from sources of heat e.g.
cookers, radiators, direct sunlight as extreme temperature
will affect its performance.

Allow a minimum 100mm (4 inches) between the top of
the freezer and the ceiling or the underside of a wall
cupboard.

Providing you follow the recommended ventilation
requirements you will :-

● Prolong the life of the freezer.

● Minimise the risk of condensation on the outside of

the freezer.

● Minimise the running costs.

● Minimise operating sounds caused by vibration.

Minimum space required to open door

The freezer needs a space of 600mm (24 inches) in front to allow the door to
open.
When positioning the freezer next to a unit, a gap of 30mm (11/4inch) can be left
at the hinge side of the door to allow the easy removal of furniture.If preferred
the freezer can be positioned so that a gap is not left.This will restrict how far the
door can be opened but the furniture can still be removed (see diagrams below).
The door hinge side can be changed to make it easier to open (see ‘Door Reversal’
in the CLEANING & MAINTENANCE section).

INSTALLATION

SAFETY &

600mm

TOP VIEW

30mm or more

TOP VIEW

600mm

less than 30mm

3

Installation

Levelling:

Level the freezer when it is in its final location by adjusting the front feet, until firm
contact is made with the floor. This will stop rocking or vibration and keep the door
aligned which helps the freezer run reliably and efficiently.

Note: Before plugging in and switching on,leave the freezer standing in its

final location for at least 15 minutes to allow it to settle.

Hinge Covers:

After the front feet have been adjusted and the freezer is level, fit the left and right

SAFETY &

hand bottom hinge covers supplied.

INSTALLATION

To fit:
Align the bottom hinge cover onto the

cover plate slots.

Push until the bottom hinge cover
clicks into place.

Joining:

Equal height Hotpoint ‘FUTURE’ fridges and freezers can be joined together to look
like one unit by using a Filler Kit available from Hotpoint Genuine Parts & Accessories
Mail Order Hotline (see KEY CONTACTS,back page).

Defrost Tube:

A tube is supplied to help feed defrost water into a collecting vessel,ie. a bowl (see
‘Defrosting’in the CLEANING & MAINTENANCE section).
For safe keeping until required, the tube can be stored in the floor of the freezer
compartment.

Defrost tube in storage position

Floor of the freezer compartment

4

Installation

Electrical Supply

WARNING:This appliance must be earthed.

The freezer must be positioned so that the plug is accessible after installation.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the
fuse, only use those rated at 13A and ASTA approved to BS1362.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING:To avoid a shock hazard do not insert the discarded plug into a socket
anywhere else.

IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE :

Green/Yellow - Earth

INSTALLATION

SAFETY &

Blue - Neutral Brown - Live

If you change the plug, the colour of wires in the mains lead may not correspond with
the colour of the markings identifying terminals in the plug. You should therefore
wire it as shown above.

Changing the Mains Lead

This freezer is fitted with a special mains lead. If you need to replace the mains lead
due to damage or require a longer lead,one can be bought from Hotpoint Service
(see KEY CONTACTS,back page). It is strongly advised that this work is carried out by
a qualified electrician.

CE Marking certifies that this appliance conforms to the following EEC
directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC

5

Controls

Controlling the Temperature of the Freezer Compartment

The control wheel on the front of the worktop adjusts the internal freezer
temperature. Your food should be maintained at -18˚C or colder for long term
storage.
The setting of the control wheel will depend on the location of the freezer, the room
temperature and how often the door is opened. The normal set point (marked by a 3
and N on the dial) is usually suitable. If you need to adjust the temperature turn the
control wheel:

Clockwise (higher number) - Colder
Anti-clockwise (lower number) - Warmer

CONTROLS

You can check the temperature of the freezer compartment by using a Fridge Freezer
Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order
Hotline (see KEY CONTACTS back page).

WARNING: Do not use a mercury filled thermometer,as breakage would cause a
health hazard.

Your freezer must NOT be placed in a room where the temperature goes below 2˚C or
above 38˚C for prolonged periods,as the internal freezer temperature will not be
maintained.

6