Hotpoint-Ariston HBRLA50 User Manual

LARDER FRIDGE - MODELS RLA50

INSTRUCTIONS FOR INSTALLATION & USE

GETTING STARTED:

STEP 1 STEP 2

To ensure that your fridge runs reliably and efficiently follow these steps.

Choose a location for your
fridge, away from any heat

allow adequate ventilation

(1

sources and

1

/4 inch) gap above.

- 30mm

STEP 3

Level the fridge by
adjusting the front feet.
This will stop rocking or

vibration and keep the

NB.The spanner is for illustration

only and is not supplied with the

door aligned.

fridge.

STEP 5

Before plugging in and
switching on, leave the

fridge in its final

location for at least 15

minutes to allow it to

settle.

STEP 4

STEP 6

Move the fridge into
position, using the sides
of the cabinet. Take care
to avoid damaging the
refrigerant circuit pipe
work on the rear.

After the front feet have
been adjusted and the
fridge is level, fit the left
and right hand bottom
hinge covers supplied.
Align with the cover
plate slots and push into
position.

Plug in and switch on.
Allow the fridge to cool
before placing food
inside.
All food in the fridge
should be covered.

INSTALLATION CONTROLS

SAFETY &

USEFUL ADVICE

MAINTENANCE

CLEANING &

TROUBLESHOOTING

STEP 7

Your fridge is now

working.

If after 24 hours your

fridge is not operating as

you want, refer to the

Troubleshooting section.

Read the rest of these instructions to get the best from your appliance

and remember to fill in your guarantee registration.

Keep this Book in a safe place for quick reference.

GUARANTEE

SERVICE &

For Your Safety

For your safety, read the following advice:

The fridge cooling system contains a small amount of gas which is environmentally
friendly but flammable. To avoid any risk :-

● Install the fridge following the installation instructions and ensure
that ventilation openings are kept clear of obstruction.

● Take care when installing or moving the fridge to avoid damaging
the pipes on the rear.

● If you suspect a leak, do not switch on the fridge,but open the
windows and doors to ventilate the room.

● Do not use any mechanical or electrical devices inside the fridge, for

SAFETY &

INSTALLATION

● Only use this fridge for storing domestic foodstuffs.

When installing your fridge :-

● Ensure that the mains cable is not trapped underneath or behind the fridge

● Do not stack any other appliance on top of this fridge as they may

When using your fridge :-

instance for manual defrosting.

when you install or move it.

damage the fridge or become unstable.

● Do not sit or stand on top of your fridge.

● Do not store poisonous, flammable or dangerous substances in your fridge.

● Do not use aerosol sprays for defrosting or cleaning your fridge.

If you sell the fridge, pass on this booklet to the new owner.

2

Installation

Location & Air Circulation

100mm
(4 inches)

Locate your fridge away from sources of heat e.g. cookers,
radiators,direct sunlight as extreme temperature will
affect its performance.

Allow a minimum 100mm (4 inches) between the top of
the fridge and the ceiling or the underside of a wall
cupboard.

Providing you follow the recommended ventilation
requirements you will :-

● Prolong the life of the fridge.

● Minimise the risk of condensation on the outside of

the fridge.

● Minimise the running costs.

● Minimise operating sounds caused by vibration.

Minimum space required to open door

The fridge needs a space of 600mm (24 inches) in front to allow the door to open.
When positioning the fridge next to a unit, a gap of 30mm (1

1

/4inch) can be left
at the hinge side of the door to allow the easy removal of furniture.If preferred
the fridge can be positioned so that a gap is not left.This will restrict how far the
door can be opened but the furniture can still be removed (see diagram below).
The door hinge side can be changed to make it easier to open (see ‘Door Reversal’
in the CLEANING & MAINTENANCE section).

INSTALLATION

SAFETY &

600mm

TOP VIEW

30mm or more

TOP VIEW

600mm

less than 30mm

3

Installation

Levelling:

Level the fridge when it is in its final location by adjusting the front feet,until firm
contact is made with the floor. This will stop rocking or vibration and keep the door
aligned which helps the fridge run reliably and efficiently.

Note: Before plugging in and switching on,leave the fridge standing
in its final location for at least 15 minutes to allow it to settle.

Hinge Covers:

After the front feet have been adjusted and the fridge is level fit the left and right

SAFETY &

INSTALLATION

hand bottom hinge covers supplied.

To fit:
Align the bottom hinge cover onto the

cover plate slots.

Push until the bottom hinge cover
clicks into place.

Joining:

Equal height Hotpoint ‘FUTURE’ fridges and freezers can be joined together to look
like one unit by using a Filler Kit available from Hotpoint Genuine Parts & Accessories
Mail Order Hotline (see KEY CONTACTS,back page).

4

Installation

Electrical Supply

WARNING:This appliance must be earthed.

The fridge must be positioned so that the plug is accessible after
installation.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the
fuse, only use those rated at 13A and ASTA approved to BS1362.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING:To avoid a shock hazard do not insert the discarded plug into a socket
anywhere else.

IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE :

Green/Yellow - Earth

INSTALLATION

SAFETY &

Blue - Neutral Brown - Live

If you change the plug, the colour of wires in the mains lead may not correspond with
the colour of the markings identifying terminals in the plug. You should therefore
wire it as shown above.

Changing the Mains Lead

This fridge is fitted with a special mains lead. If you need to replace the mains lead
due to damage or require a longer lead,one can be bought from Hotpoint Service
(see KEY CONTACTS,back page). It is strongly advised that this work is carried out by
a qualified electrician.

CE Marking certifies that this appliance conforms to the following EEC
directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC

5

Controls

Controlling the Temperature of the Fridge Compartment

The control wheel on the front of the worktop adjusts the internal fridge
compartment temperature. The internal temperature should be 5˚C or colder
although some sections, such as the salad bin, will be slightly warmer.
The setting of the control wheel will depend on the location of the fridge,the room
temperature and how often the door is opened. The normal set point (marked by a 3
and N on the dial) is usually suitable. If you need to adjust the temperature turn the
control wheel:

Clockwise (higher number) - Colder
Anti-clockwise (lower number) - Warmer

CONTROLS

You can check the temperature of the fridge compartment by using a Fridge Freezer
Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order
Hotline (see KEY CONTACTS back page).

WARNING: Do not use a mercury filled thermometer,as breakage would cause a
health hazard.

Your fridge must NOT be placed in a room where the temperature goes below 6˚C or
above 38˚C for prolonged periods,as the internal fridge temperature will not be
maintained.

6

Useful Advice

A

A

B

B

C

D

Note:
The Rating Plate,which lists the appliance Model Number and Serial
Number can be found near the bottom of the interior wall.

STORAGE ZONES

Zone Type Food Storage

A Cool Dairy products, Cheese,butter,margarine,

Low fat spreads,cooking fats / lards
Preserves - Jam, curd, marmalade,
spread,salad dressing or sauces.

B Colder General food storage

C Coldest Meat fish & poultry

Pre-cooked / chilled food

D Salad Bins / Vegetables,fruit and salad items

Vegetable Flap (Not recommended for the storage of

bananas or onions).

B

USEFUL ADVICE

7

Useful Advice

Making the best use of your Fridge

To ensure that your fridge operates as efficiently as possible :

● Follow food packaging “best before/use by”instructions or your suppliers
advice on a suitable maximum storage time.

● Keep foods covered to retain moisture and prevent flavour/odour
transference. Plastic bags,aluminium foil, plastic stretch wrap and containers
with lids are ideal.

● Avoid opening the doors unnecessarily or for longer than needed.

● Allow hot or warm food to cool down in covered containers before placing in

fridge, as placing hot food inside reduces efficiency.

Storing Food in a Fridge

● Pack and store cooked and fresh food separately.

● Wrap raw or defrosting meat and poultry in polythene or foil and store

below cooked foods and dairy products to avoid contamination of dripping
food juices.

● Wrap cheese in greaseproof paper and place in an airtight container or
polythene bag.
Bring to room temperature before consuming.

● Empty left over canned food into a covered storage containers before
placing in the fridge.

● Position food to allow cold air to circulate freely, ensuring nothing comes
into contact with the interior back wall of the fridge,or covers the defrost

USEFUL ADVICE

● Use the different storage zones inside your fridge compartment to store a

gutter drain hole below this.

wide variety of food items.

8

Useful Advice

Commodity and Bottle Racks

Commodity racks can be repositioned in the door to suit your storage requirements.
The lidded commodity rack is recommended for the storage of dairy items,such as
butter,margarine and cheese.
To remove, lift rack vertically to release from fixing supports.

To replace, align grooves on either side of the rack above fixing supports and push
down until secure.

In order to get the best results from the bottle retainer it is advised that it be
positioned centrally on the bottle rack.

Egg Rack

The egg rack can be used in conjunction with any commodity rack and is easily
removed for cleaning.

Note: Wipe,don’t wash eggs.

Advice on Adjusting Shelves

Make the most of the interior storage
space by repositioning shelves to suit the
various heights of individual items you
wish to store.

To remove, ensure that the door is open fully.
Slide the shelf forward and tilt from position.

Split Glass Shelf

The split shelf can be used as a standard shelf but also as
two half shelves.
The front half can be repositioned above or below to
enable storage of larger items.

USEFUL ADVICE

Note : Only the front half of the
shelf can be repositioned, the back
half must remain in its original
position.

9

Useful Advice

Salad Bins

For the storage of fruit,vegetables and salad items.
When storing vegetables,remove unusable leaves and soil and leave lettuce, cabbage
and cauliflower on the stem.
It is advisable to clean the salad bin regularly,it can be removed by sliding it out from
position.

Note : Care must be taken to ensure that the salad bin is pushed in fully before
shutting the fridge door.

Vegetable Bin

This is an additional area, recommended for the storage of larger vegetable items
(such as cauliflower, cucumber and other items which do not fit into the salad bins).
When storing vegetables,remove unusable leaves and soil. Leave lettuce, cabbage
and cauliflower on the stem.

To open hold the front handle and pull to
tilt the bin forwards to access foodstuffs.

To close, keep hold of the handle and
allow the bin to go back into position.

It is advisable to clean the vegetable bin regularly,it can be removed by sliding it out

USEFUL ADVICE

from position.

Note : Care must be taken to ensure that the vegetable bin is closed before
shutting the fridge door.

Wine Rack

The wine rack is suitable for cans,wine bottles and 2 litre bottles. The maximum load
recommended is three 2 litre bottles and two wine bottles.

Position the wine rack in the second runner down from the top of the fridge when
storing longer length bottles. This will ensure the bottles clear the door furniture and
allow the door to close properly.

Note: DO NOT remove a fully loaded wine rack, just remove bottles as necessary.

To remove:
Ensure that the fridge door is fully open.
Slide the wine rack forward and tilt from position.

10

Defrosting

Defrosting

No manual defrosting required

The fridge compartment will defrost automatically. During defrost periods water
droplets form on the interior back wall of your Larder Fridge and refreeze afterwards.

WARNING:Ensure that stored food does not come into contact with the interior
back wall of your Larder Fridge. Also ensure the defrost gutter drain hole is kept
clear,see ‘Cleaning’in the CLEANING & MAINTENANCE section.

11

MAINTENANCE

CLEANING &

Cleaning

Cleaning

WARNING: Switch off electrical supply and pull out mains plug before cleaning.

Interior

Note : We recommend you use a straw to keep the defrost gutter drain hole
clear of any blockage.DO NOT use sharp metal tools which could cause
damage beyond repair.

WARNING:Do not use abrasive powder, household cleaner, bleach or wax polish
to clean the interior, they will leave a smell in the fridge.

1. Remove stored food,wrap or cover it and place into insulated containers to
keep cool whilst cleaning.

2. Remove salad bins,racks and shelves from the fridge compartment.
Wash in warm water and washing up liquid using a soft cloth,dry
thoroughly.
DO NOT use any cleaning agents on the wine rack, just wipe with a soft cloth.

3. Wipe the interior and fittings with a clean cloth wrung out in a solution of
either one teaspoon of bicarbonate of soda to one pint of water or Milton™
sterilising fluid, diluted according to the manufacturer’s instructions.

4. Dry the interior thoroughly with a clean cloth before replacing fittings and
food.

Note : It is important to ensure that cleaned shelves, racks and bins are
thoroughly dried before refitting to the fridge compartment.

Exterior

WARNING:Do not use abrasive powder, household cleaner or bleach they can

CLEANING &

MAINTENANCE

damage the exterior of your fridge.

1. Use a clean soft cloth wrung out in warm water and washing up liquid to

wipe the exterior surface, dry thoroughly.

2. Use a soft brush or vacuum cleaner to remove dust from underneath the

fridge and from the compressor and condenser situated at the back of the
fridge

WARNING: Do not damage the pipework.

Door Seal

Use warm water and a clean soft cloth to wipe along and in between the creases of
the door seal, dry thoroughly. Take care not to damage the seal and avoid using
sharp objects.

WARNING: Do not use detergent,it will damage the seal.

12

Maintenance

Going Away

If you are going away and don’t want to use your fridge, switch off the electricity
supply and pull out the mains plug. Remove food and follow the cleaning
instructions on the previous page.

Note : Leave the door ajar to prevent an accumulation of odours.

Changing the Light Bulb

WARNING:Switch off electricity supply and pull out the mains plug

Obtain a replacement SES 15 watt bulb from the Hotpoint Genuine Parts and
Accessories Mail Order Hotline (see KEY CONTACTS back page) and fit as follows :

1. Remove any shelves from directly below the interior light,to make access
easier.

2. Squeeze the side of the lamp guard lightly to unclip. Remove and retain.

3. Remove old bulb and fit new one.

4. Refit lamp guard.

5. Plug in and switch on electrical supply.

13

MAINTENANCE

CLEANING &

Door Reversal

Door Reversal

You will need a cross head screwdriver,a flat blade screwdriver and a 5mm spanner to
carry out this procedure.
Our Service Department can arrange for an Engineer to do the conversion for you but
a charge will be made.

WARNING:Switch off electrical supply and pull out the mains plug.

Remove all door furniture and all loose items/fittings from inside the fridge.

If you have previously set up and used the fridge and since decided to reverse the
doors, you must remove stored food,wrap or cover it and place into insulated
containers to keep cool whilst carrying out this operation.

1. Open the door as wide as possible.

Note : You may require assistance to do this:

2. Support the door and using a screwdriver,remove the screw
securing the top hinge.

3. Lower the top hinge and carefully tilt the door to remove the
hinge from the cabinet. Lift the door off the bottom hinge.

4. Remove the top hinge from the door.

5. Remove the spacing washers from the bottom hinge pin.

6. Use a flat blade

screwdriver or a 5mm
spanner,to unscrew
and remove the
bottom hinge pin.

7. Unscrew the fixing
screw to remove the
right hand hinge cover
plate.
Then remove the door
stop washer.

8. Replace the right hand

CLEANING &

MAINTENANCE

cover plate with its
original screw.

10. Unscrew the fixing screw to remove the left hand hinge cover plate.

11. Firstly put the door stop
washer in position on
the left hand hinge
bracket and then screw
in the hinge pin.

13. Replace the spacing washers onto the hinge pin.

14

9. Take the plastic cap
from the left hand
cover plate and use it
to fill the hole on the
right hand cover plate.

12. Replace the left hand
cover plate with its
original screw.

Door Reversal

14. Using a thin blunt instrument, remove the hinge
bush cap from the top left of the door and refit on
the top right.

15. Use a screwdriver to remove the door stop from the
bottom right of the door and refit on the bottom
left.

Door Handle Reversal:
Note: this MUST be completed with the door OFF the product.

16. Remove the hole plugs from the right hand side of the door.

17. Unscrew the handle cover retaining screws and remove the covers.

18. Unscrew the handle fixing screws and remove the handle from the door.

19. Turn the handle vertically, top to bottom and place it in position against the

right hand side of the door.

20. Secure the handle in place with the original fixing screws.

21. Fit the handle covers in position,using the original retaining screws.

22. Use the hole plugs removed from the right hand side to fill holes on the left.

Note : You may require assistance to do this:

23. Place the top hinge onto the door, slide the door onto the

bottom hinge pin and support the door whilst screwing the top
hinge bracket into position.
Ensure that the top hinge bracket is positioned correctly.

door stop

MAINTENANCE

CLEANING &

24. Adjust the front feet (see ‘Levelling’SAFETY & INSTALLATION section).

25. Fit the bottom hinge covers (see ‘Hinge Covers’ in the SAFETY &

INSTALLATION section).

Note : Let the appliance stand upright in it’s final location for at least 15
minutes before plugging in and switching on the electricity supply.

15

Troubleshooting

IS THE FRIDGE WORKING AS YOU
WANT?

Have you read through the instruction
book ?
If you still have a problem,before calling
our service organisation see if any of the
tips below help.

The fridge will not work

1. Check plug is firmly positioned in the

socket outlet and the power supply is
switched on.

2. Check power supply with another

appliance.

3. Check fuse/circuit breaker.

4. Check the door is closed properly.

The fridge is making a lot of noise

1. Check that the rear pipe work is clear

of the wall, skirting board and other
obstacles.

2. Check that all feet/wheels are firmly

in contact with the floor and the
fridge is level.

3. See OPERATING SOUNDS below.

The temperature is too warm

1. Turn the control wheel to a higher

number. See CONTROLS section.

2. If the fridge is close to a heat source,

move it to another location.

3. Check that there is enough

ventilation around the appliance.

4. Check that the door has been closed

properly.

The interior light doesn’t work

WARNING:Switch off electricity supply
and pull out the mains plug.

1. Check bulb is screwed in correctly. If
still not working then see ‘Changing
the Light Bulb’in the CLEANING &
MAINTENANCE section.

Ice builds up rapidly inside the fridge

1. Check that nothing is stopping the
door from closing properly.

2. Check that foods and liquids are
covered to avoid the build up of
moisture inside.

3. If your kitchen becomes exceptionally
warm your fridge may not defrost
regularly. Automatic defrosting will
return to normal operation when the
kitchen temperature cools.

If there is still a problem contact
Hotpoint Service (See KEY CONTACTS,
back page, for contact details).

OPERATING SOUNDS OF A FRIDGE

These are the normal types of sound that
your fridge will make:

The fridge motor (compressor) makes a
buzzing or humming sound when it is
running. This can be louder when it is
first switched on. This sound will reduce
over the first few months.

The temperature is too cold

1. Turn the control wheel to a lower
number. See CONTROLS section.

TROUBLESHOOTING

There is water beneath the salad bin
and on the floor

1. Check defrost gutter drain hole is not
covered or blocked,see ‘Cleaning’in
the CLEANING & MAINTENANCE
section.

2. Check that nothing has come into
contact with the interior back wall of
the fridge.

16

Gases flowing through the pipes can
produce gurgling,bubbling, roaring or
humming noises.

The temperature control can make a
clicking noise when it turns the motor on
and off.

Expansion and contraction of parts
inside the fridge can produce a cracking
noise as they rapidly change
temperature.

Notes

17

Hotpoint guarantee

“Satisfaction guaranteed or your money back”

We give you a unique ‘satisfaction guaranteed’promise - valid for 90 days - after you have

purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint

Repair service or visit our web-site at www.theservicecentre.co.uk and where necessary, we

will arrange for an engineer to call. If the technical problem is not resolved under this

guarantee, we will replace your machine or,if you prefer, give you your money back.

All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well
as free replacement parts for the first 5 years (except microwaves, selected integrated
appliances and cooker hoods, which have a one year guarantee) provided that they are
fitted by a Hotpoint engineer.

Guarantee terms and conditions

Your guarantee is only applicable in the United Kingdom or Republic of Ireland
and is subject to the following provisions that your appliance:

●

●

●

●

Has been installed and used correctly in accordance with this instruction booklet.
Has been used solely for domestic purposes and is located on domestic

premises (ie. not for commercial or trade use).
Has been properly connected to a suitable electrical supply voltage as stated on
the appliance rating plate.
Has not been subject to misuse, accident, modified or repaired by anyone other
than a Hotpoint service engineer.

For pre purchase information on any other Hotpoint product call: 08701 50 60 70

or visit: www

.hotpoint.co.uk

Recycling & Disposal Information

As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves
the right to use quality recycled components to keep down customer costs and minimise
material wastage.

Please dispose of packaging and old appliances carefully. Old refrigerant and oil must be
disposed of in a safe and environmentally friendly manner, using suitably qualified

SERVICE &

GUARANTEE

personnel.
To minimise risk of injury to children, remove the door, plug and cut mains cable off flush

with the appliance. Dispose of these parts separately to ensure that the appliance can no
longer be plugged into a mains socket, and the door cannot be locked shut.

18

After Sales Service

“No company is better positioned to offer an after sales service on a

As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully

inclusive parts and labour guarantee for the first 12 months. In addition to this you also have

the advantage of free replacement parts for the first 5 years when fitted by a Hotpoint

engineer. When the 12 months parts and labour guarantee expires we offer the following after

Note: Our operators will require the Model number and the Serial number of your appliance

Available 364 days a year with a fast, effective and value for money service.We have the largest

white goods repair service in the UK with over 1200 of our own fully trained engineers. All

repairs include a parts and labour guarantee for 12 months from the date of the repair.

If you require any information or have any questions about your appliance, our operators are on

All this ensures that you will receive the best available after sales service possible.

Whether you have just one or a number of Hotpoint appliances in your kitchen,we offer two

●

Repair Protection Plan - FREE service repairs for a single Hotpoint appliance during the

●

Kitchen Cover - FREE service repairs for all your Hotpoint appliances less than 8

Hotpoint appliance than us - the manufacturer”

sales service options:

Repair Service and Information Help Desk

(see USEFUL ADVICE SECTION for rating plate position).

service cover plans to give you total peace of mind.

period of cover.

years old.

UK: 08709 066066

www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

hand with help and advice.

Extended Warranties

UK: 08709 088 088

www.theser

Republic of Ireland: 1850 502 200

vicecentre.co.uk

Genuine Parts and Accessories

UK: 08709 077 077

www.theservicecentre.co.uk

Republic of Ireland: [phone]

A wide range of genuine parts and accessories are available from our hotline or through

our web site.

Genuine parts and accessories, extended warranties and service repairs are all

available on our web-site at:

www.theservicecentre.co.uk

19

GUARANTEE

SERVICE &

Key Contacts

After Sales Service

Over 1200 trained specialists, directly employed by us, ensure that you can have

complete confidence in both the appliances and services we offer.

Repair Service and Information Desk

(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)

Note: Our operators will require the following information:

See USEFUL ADVICE SECTION for rating plate position

UK: 08709 066 066

www

.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Model number:

Serial number:

Extended Warranties

UK: 08709 088 088

(Open 8 to 8 Mon - Sun)

www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Genuine Parts and Accessories

(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)

General Domestic Appliances Limited,Morley Way, Peterborough, PE2 9JB.

PRINTED BY SIMLEX.FOUR ASHES,WOLVERHAMPTON. September 2002 2766200014-02

UK: 08709 077 077

www.theservicecentre.co.uk

Republic of Ireland: [phone]