Hotpoint NVLR223EG Dimension Manual
NVLR223EG – Hotpoint 5.8 Cu. Ft. Extra-Large Capacity Electric Dryer
Dryer Dimensions (in inches)
Exhaust Options:
4-way via rear, right, left and bottom.
Circuit Requirements:
An individual, properly-grounded branch circuit, protected by a
30-amp circuit breaker or a time-delay fuse, is required.
Electric Dr yer Rating:
240V, 5600W, 60Hz, 24 Amp
208V, 4400W, 60Hz, 22 Amp
Installation Information: For complete information, see installation
instructions packed with product for current dimensional data.
* 24-1/2” from the edge of the side panel to the front.
25-1/2” from front to edge of end caps.
Specification Revised 12/06
470150
Listed by
Underwriters
Laboratories
36
25-1/2
42
54-1/2
Side View
27
Rear View
36
42
27
2
3-1/2
2-1/2
25-1/2*
Side View
Rear View
5-1/4
25-3/4
23-1/2
11-1/2
Special Installation Requirements
Alcove or Closet Installation:
• If your dr yer is approved for installation in an alcove or closet, it will be stated on a
label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other sur faces are:
0" either side
3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or other wise ventilated and must contain a minimum of
60 sq. in. of open area equally distributed. If this closet contains both a washer and a
dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes,
with the National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides
3" rear
Dryer exhausting information
For complete information see installation instructions packed with dryer.
Important note:
5.8 cu. ft., 6.0 cu. ft. and 7.0 cu. ft. dr yers do not require additional parts to convert to bottom
or side venting. Unitized models do not require a kit for side venting.
Ducting materials
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If “all rigid
metal” duct cannot be used, then “flexible all metal” venting can be used, but it will reduce the maximum
recommended duct length. The following kit or parts are available from your local service organization.
Kit WX8X75 – 7' aluminum duct and 4' hood, short tail.
(OR individual parts):
WX8X65 7' aluminum flex duct only
WX8X58 4' clamps (2)
WX8X67 4' exhaust hood
See installation instructions for complete information.
Exhaust length calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of
dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is shown in the
table. The maximum lengths for flexible ducts are less than for rigid duct.
See table in installation instructions. A turn of 45° or less may be ignored. Two 45° turns within the duct
length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large amounts of moisture
and lint from being blown into the room. Gas dryers or any dryer located in a closet must be exhausted to
the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor
(crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause
damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the
combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The
wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed
down. Other terminations, such as louvered wall boxes, are acceptable provided they are equivalent to a
4" opening dampered wall cap.
NVLR223EG – Hotpoint 5.8 Cu. Ft. Extra-Large Capacity Electric Dryer
Dryer Exhausting Information – Use Metal Duct Only
Vertical and Horizontal Ducting
Specification Revised 12/06
470150
Listed by
Underwriters
Laboratories
A
A
4
GE Dryer Vent
B
2-1/2
Best Per formance
Maximum Le ngth of 4" Dia.
Rigid Met al Duct
Maximum Le ngth of 4" Dia.
Flexible M etal Duct
Exhaus t Hood Type Exhaus t Hood Type
Domesti c
Dryer M odels
Number
of
90°
Turns
A
4" OpeningB2-1/2"
Opening
A
4" OpeningB2-1/2"
Opening
7.0, 6.0 and 5.8
Capacit y Models
all Electr ic Dryers
0
1
2
3
4
90 ft .
60 ft .
45 ft .
35 ft.
25 ft.
65 ft .
45 ft .
35 ft.
25 ft.
15 ft.
55 ft .
40 ft .
30 ft .
20 ft .
15 ft.
45 ft .
30 ft .
20 ft .
15 ft.
10 ft.
7.0, 6.0 and 5.8
Capacit y Models
all Gas Dr yers
0
1
2
3
90 ft .
60 ft .
45 ft .
35 ft.
60 ft .
45 ft .
35 ft.
25 ft.
55 ft .
40 ft .
30 ft .
20 ft .
45 ft .
30 ft .
20 ft .
15 ft.
Spacema ker® Models
DSK S433EB
DSK S333EC
DSK P333EC
WS M2780H
0
1
2
3
46 ft .
38 ft .
31 ft.
24 ft.
37 ft.
30 ft .
22 ft .
15 ft.
30 ft .
25 ft.
20 ft .
16 ft.
24 ft.
20 ft .
14 ft.
10 ft.
Spacema ker Model
WS M2700H
0
1
2
3
56 ft .
46 ft .
34 ft .
32 ft .
42 ft.
36 ft .
28 ft .
18 ft.
30 ft .
22 ft .
16 ft.
10 ft.
22 ft .
14 ft.
10 ft.
5 ft.
Spacema ker Models
WS M2420D
WS M2480D
0
1
2
43 ft .
33 ft .
23 ft .
36 ft .
26 ft .
16 ft.
30 ft .
24 ft.
16 ft.
24 ft.
18 ft.
10 ft.
Loading...