Hotpoint DBLR333GG2CC, DBLR333GG2WW, DBLR333GG3CC, DBLR333GG3WW, DBLR333GG4CC Installation Guide

...

Hotpoint DBLR333GG2CC, DBLR333GG2WW, DBLR333GG3CC, DBLR333GG3WW, DBLR333GG4CC, DBLR333GG4WW, DBLR333GG5CC, DBLR333GG5WW, DBLR333GG6CC, DBLR333GG6WW, DBSR463GG1WW, DBSR463GG2WW, DBSR463GG3WW, DBSR463GG4WW, DBSR463GG5WW, DBSR463GG6WW, DBSR463GG7WW, DBVH510GH2WW, DBVH510GH3WW, DBVH512GF2WW, DBVH512GF3WW, DBVH512GF4WW, DBVH512GF5WW, DBVH520GJ2WW, DBXR300GG1WS, DBXR300GG2WS, DBXR300GG3WS, DBXR300GG4WS, DBXR300GG5WS, DBXR300GG6WS, DBXR463GG1CC, DBXR463GG1WW, DBXR463GG2CC, DBXR463GG2WW, DBXR463GG3CC, DBXR463GG3WW, DBXR463GG4CC, DBXR463GG4WW, DBXR463GG5CC, DBXR463GG5WW, DBXR463GG6CC, DBXR463GG6WW, DBXR463GG7CC, DBXR463GG7WW, DBXR463PG1CC, DBXR463PG1WW, DBXR463PG4CC, DBXR463PG4WW, DCVH515GF1GG, DCVH515GF1WW, DCVH515GF2WW, DCVH515GF3WW, DCVH515GF4WW, DCVH515GF5WW, DCVH640GJ1WW, DCVH660GH0BB, DCVH660GH0GG, DCVH660GH0MB, DCVH660GH0MS, DCVH660GH0WW, DCVH660GH1BB, DCVH660GH1GG, DCVH660GH1MB, DCVH660GH1MS, DCVH660GH1WW, DCVH660GH2BB, DCVH660GH2GG, DCVH660GH2MB, DCVH660GH2MS, DCVH660GH2WW, DCVH660GH3BB, DCVH660GH3GG, DCVH660GH3MB, DCVH660GH3MS, DCVH660GH3WW, DCVH680GJ1BB, DCVH680GJ1MR, DCVH680GJ1MS, DCVH680GJ1WW, DHDSR46EG2WW, DHDSR46GG1WW, DHDSR46GG2WW, DHDSR46GG3WW, DHDSR46GG4WW, DHDSR46GG5WW, DHDSR46GG6WW, DHDSR46GG7WW, DHDVH52GF5WW, DHDVH66GH0BB, DHDVH66GH0GG, DHDVH66GH0WW, DHDVH66GH1BB, DHDVH66GH1GG, DHDVH66GH1WW, DHDVH66GH2BB, DHDVH66GH2GG, DHDVH66GH2WW, DHDVH66GH3BB, DHDVH66GH3GG, DHDVH66GH3WW, DHDVH68GJ1MR, DHDVH68GJ1MS, DHDVH68GJ1WW, DJXR433GG1CC, DJXR433GG1WW, DJXR433GG2CC, DJXR433GG2WW, DJXR433GG3CC, DJXR433GG3WW, DJXR433GG4CC, DJXR433GG4WW, DJXR433GG5CC, DJXR433GG5WW, DJXR433GG6CC, DJXR433GG6WW, DJXR433GG7CC, DJXR433GG7WW, DLLLR23GG0WW, DLLLR23GG1WW, DLLLR23GG2WW, DLLLR23GG3WW, DLLLR23GG4WW, DLLLR23GG5WW, DLLLR23GG6WW, DLLLR23GG7WW, DLLLR33GJ0WW, DLLLR33GJ1WW, DLLLR33GJ2WW, DLLLR33GJ3WW, DLLSR34GG0WW, DLLSR40GG0WW, DLLSR40GG1WW, DLLSR40GG2WW, DLLSR40GG3WW, DLLSR40GG4WW, DLLSR40GG5WW, DLLSR40GG6WW, DLLSR40GG7WW, DLSR483GG1WW, DNCD450GG0WC, DNCD450GG2WC, DNCD450GG5WC, DNCK440GG0WC, DNCK440GG2WC, DNCK440GG4WC, DNCK440GG5WC, DPSE810GG1WT, DPSE810GG2WT, DPSE810GG3WT, DPSE810GG4WT, DPSE810GG5WT, DPSE810GG6WT, DPSR610GG1WT, DPSR610GG2WT, DPSR610GG3WT, DPSR610GG4WT, DPSR610GG5WT, DPSR610GG6WT, DRSR483GG1CC, DRSR483GG1WW, DRSR483GG2CC, DRSR483GG2WW, DRSR483GG3CC, DRSR483GG3WW, DRSR483GG4CC, DRSR483GG4WW, DRSR483GG5CC, DRSR483GG5WW, DRSR483GG6CC, DRSR483GG6WW, DRSR483GG7CC, DRSR483GG7WW, DRSR495GG1WW, DRSR495GG2WW, DRSR495GG3WW, DRSR495GG4WW, DRSR495GG5WW, DRSR495GG6WW, DRSR495GG7WW, DVLR223GG1WW, DVLR223GG2WW, DVLR223GG3WW, DVLR223GG4WW, DVLR223GG5WW, DVLR223GG6WW, DVLR223GG7WW, DWSR463GG1WW, DWSR463GG2WW, DWSR463GG3WW, DWSR463GG4WW, DWSR463GG5WW, DWSR463GG6WW, DWSR463GG7WW, DWSR483GG1CC, DWSR483GG1WW, DWSR483GG2CC, DWSR483GG2WW, DWSR483GG3CC, DWSR483GG3WW, DWSR483GG4CC, DWSR483GG4WW, DWSR483GG5WW, DWSR483GG6CC, DWSR483GG6WW, DWSR483GG7CC, DWSR483GG7WW, DWXR463GG1WW, DWXR463GG2WW, DWXR463GG3WW, DWXR463GG4WW, DWXR463GG5WW, DWXR463GG6WW, DWXR463GG7WW, DWXR483GG1WW, DWXR483GG2WW, DWXR483GG3WW, DWXR483GG4WW, DWXR483GG5WW, DWXR483GG6WW, DWXR483GG7WW, DX2300GG1WW, DX2300GG2WW, DX2300GG3WW, DX2300GG4WW, DX2300GG5WW, DX2300GG6WW, DX2300GG7WW, DX4500GG0WW, DX4500GG1WW, DX4500GG2WW, DX4500GG3WW, DX4500GG4WW, DX4500GG5WW, DX4500GG6WW, DX4500GG7WW, EED4600G0WW, EED4600G2WW, EED5600G0WW, EED5600G2WW, EED5600G5WW, EGD4600G0WW, EGD4600G1WW, EGD4600G2WW, EGD4600G3WW, EGD4600G4WW, EGD4600G5WW, EGD4600G6WW, EGD4600G7WW, EGD5600G0WW, EGD5600G1WW, EGD5600G2WW, EGD5600G3WW, EGD5600G4WW, EGD5600G5WW, EGD5600G6WW, EGD5600G7WW, NBXR333GG0WW, NBXR333GG1WW, NBXR333GG2WW, NBXR333GG3WW, NBXR333GG4WW, NBXR333GG5WW, NBXR333GG6WW, NVLR223GG0WW, NVLR223GG1WW, NVLR223GG2WW, NVLR223GG3WW, NVLR223GG4WW, NVLR223GG5WW, NVLR223GG6WW, NVLR223GG7WW, NVLR223GH1WO, NVLR223GH2WO, NVLR223GH3WO, NVLR223GH4WO, NVLR223GH5WO, NVLR223GH6WO, NVLR223GH7WO, NWXR483GG0WW, NWXR483GG1WW, NWXR483GG2WW, NWXR483GG3WW, NWXR483GG4WW, NWXR483GG5WW, NWXR483GG6WW, NWXR483GG8WW, NWXR483GG9WW Installation Guide

Inst II "

GasDryer

Inst uct"

I If you have any questions, carl 1-800-GECARES (US) or 1-800-361-3400 (Canada)

or Visit our Web site at: www. GEAppliances.com

BEFOREYOU BEGIN

Read these instructions completely and carefully.

IMPORTANT -Savethese

instructions for local inspector's use.

IMPORTANT =Observeall

governing codes and ordinances.

Note to Installer - Be sure to leave these instructions with

the customer

Note to Customer - Keep these instructions with your Use

and Care Book for future reference.

This dryer must be exhausted to the outdoors. Before the old dryer is removed from service or discarded,

remove the dryer door.

Service Information and the wiring diagram are located in

the control console.

Service of this dryer must be performed by a qualified

installer,service agency, or the gas supplier.

Do not allow children on or in the appliance. Close

supervision of children is necessary when the appliance is

used near children.

TOOLS YOU WiLL NEED

MATERIALS YOU WILL NEED

FORYOUR SAFETY:

,_kWARNING

• Use only rigid metal or flexible metal 4-in. diameter

ducrwork for exhausting to the outdoors. Never use plastic or other combustible easy-to-puncture ductwork.

• This appliance must be properly grounded and installed

as described in these instructions.

• Do not install or store appliance in an area where it

will be exposed to water and/or weather.

• The National Fuel Gas Code restricts installations of gas appliances in garages. They must be 18 in. off the

ground and protected by a barrier from vehicles.

• Install the dryer where the temperature is above 50°F for satisfactory operation of the dryer control system.

10"ADJUSTABLEWRENCHES(2)

8"PIPEWRENCH

Step 1 Step 2

Step 3

Step 4 Step 5 Step 6 Step 7

Verify Your Gas Installation (see section 2).

Prepare the Area and Exhaust for Installation of New Dryer (see section 1). Check and Insure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation Specifications.(see section 6)

Remove the Foam Shipping Pads (see section 1). Move the Dryer to tile Desired Location. Level Your Dryer (see section 8). Connect tile Gas Supply (see section 3) and check

for leaks (see section 4).

SLIPJOINTPLIERS

FLATBLADESCREWDRIVER

LEVEL

4"DIA,METALELBOW

PIPECOMPOUND

FLEXIBLEGASLINECONNECTOR

Step 8 Connect the External Exhaust (see section 7). Step 9 Connect the Power Supply (see section 5). Step 10 Check the Operation of the Power Supply, Gas

Step 11 Place the Owners Manual and the Installation

For Alcove or Closet Installation see section 9. For Bathroom or Bedroom Installation see section 10. For Mobile or Manufactured Home see section 11.

4"DIA,METALDUCT

4"DIA.FLEXIBLEMETALDUCT

Connections, and Venting.

Instructions in a Location Where They _rill Be

Noticed By the Owner.

(RECOMMENDED)

(IFNEEDED)

GLOVES

DUCT SOAPSOLUTION CLAMPS(2) FORLEAKDETECTION

EXHAUSTHOOD

SAFETYGLASSES DUCTTAPE

Installation instructions

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and fox'air opening are: 0 in. clearance both skies and 1 in. rear. Consideratkm must be given to provkte adequate clearance for proper operation and service.

[] PREPARING FOR iNSTALLATiON

OF NEW DRYER

CSA(AGA)APPROVED

NEWFLEXIBLEGAS LINECONNECTOR

GAS EXTERNAL DUCT OPENING

DUD] TAPE

TIP: Install your dryer before installing your washer. _[his will allow better access when installing dryer exhaust.

INLET

PIPE

4"METALDUCT \

DUCT

TAPE

DiSCONNECTiNG GAS

SHUT-OFF

VALVETOTHE

OFFPOSITION.

TURNGAS . .__

TILTTHEDRYERSIDEWAYS ANDREMOVETHEFOAM

SHIPPINGPADSBY

PULLINGATTHESIDES ANDBREAKINGTHEM AWAYFROMTHEDRYER

LEGS,BESURETO

REMOVEALLOFTHE

FOAMPIECESAROUND THELEGS.

[] GAS REQUIREMENTS

WARNING

. Installation must conform to local codes and ordinances,

or in their absence, the NATIONAL FUEL GAS CODE, ANSI Z223.

. This gas dryer is equipped with a Valve & Burner Assem-

bly for use only with natural gas. Using conversion kit WE25X0217, your local service organization can convert this dryer fox'use with propane (LP) gas. ALL CONVER-

SIONS MUST BE MADE BY PROPERLY TRAINED AND QUALIFIED PERSONNEL AND IN AC-

CORDANCE WITH LOCAL CODES AND ORDI- NANCE REQUIREMENTS

. The dryer must be disconnected fl'om the gas supply

piping system during any pressure testing of that system at a test pressure in excess of 05 PSI (3.4 KPa)

° The dryer must be isolated from the gas supply piping

system by closing the equipment shut-off valve during any pressure testing of the gas supply piping of test

pressure equal to or less than 05 PSI (3.4KPa).

DRYER GAS SUPPLY CONNECTION

DISCONNECTANDDISCARDOLD FLEXIBLEGASCONNECTOR ANDOLDDUCTINGMATERIAL.

WARNING - NEVERREUSE OLD

FLEXIBLE CONNECTORS.

The use of old flexible connectors can cause leaks and personal injury. Always use new flexible connectors when

installing gas appliances.

REMOVING LiNT FROM WALL EXHAUST OPENING

WALL

INTERNALDUCT CHECKTHATEXHAUST OPENING OPENS

ANDCLOSESFREELY,

I 24/8" 3/8"NPTMALETHREADGASSUPPLY

GAS SUPPLY

A 1/8-in. National Pipe Taper thread plugged tapping, ac- cessible for test gauge connection, must be installed imme- diately upstream of the gas supply connection to the dryer.

Contact your local gas utility should you have questions on

the installation of the plugged tapping.

Supply line is to be 1/2-in. rigid pipe and equipped with an

accessible shut-offwithin 6 ft. of, and in the same room

with, the dryer. Use pipe thread sealer compound or Teflon tape appropriate for natural or LP gas.

You must use with this dwer a flexible metal connector listed

connector ANSI Z21.24 / CSA 6.10. The length of the connect shall not exceed 3 ft.

Connect flexible metal connector to dryer and gas supply.

Open shut-offvalve_

NOTE:Addtoverticaldimension thedistancebetweencabinet

bottomtofloor.

Installation

[] RECONNECTING GAS

Listed connector ANSI Z21.24 / CSA 6.10

118" NPT PIPE

NEW METAL PLUG FOR

FLEXIBLEGAS INLET PRESSURE LINECONNECTOR

ADAPTER

3/8" NPT

ELBOW

ITEMSNOT SUPPLIED --AT LEAST I/2"

Note: The connector and fittings are designed for use only on the original instaUation and are not to be reused for another appUance or at another tocation, Keep flare end of adaptor free of grease, oil and thread seal.ant,

Caution: Use adapters as shown. Connector nuts must not be connected direcNy to pipe threads.

SHUT-OFF

PIPESIZE

Instructions

APPLYPIPECOMPOUND TOALL MALETHREADS.

GAS

APPLYPIPECOMPOUND

TOTHEADAPTERAND

DRYERGASINLET.

TIGHTEN THE FLEXIBLE

GASLINE USING TWO ADJUSTABLEWRENCHES.

TIGHTEN ALL CONNECTIONS

USING TWO ADJUSTABLE WRENCHES. DO NOT OVERTORQUE GAS CONNECTIONS!

[] LEAK TEST

,_ WARNING - NEVER USE AN OPEN

FLAME TO TEST FOR GAS LEAKS.

OPEN

GASVALVE,

Check all connections for leaks with soapy solution or equivalent. Apply soap solution. Leak test solution must not contain ammo-

nia which could ceuse damage to the brass fittings. If leaks are

found, close valve, retighten the joint, and repeat the soap tesL

Installation

instructions

[] ELECTRICAL CONNECTION

iNFORMATiON

WARNING- TO REDUCE THE RISK OF

FIRE, ELECTRICAL SHOCK, AND PERSONAL INJURY:

DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.

Dryer must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, in accordance with the NATIONAL ELECTRI- CAL CODE, ANSI/NFPA NO. 70.

ELECTRICAL REQUIREMENTS

This appliance must be supplied with 120V, 60Hz, and connected

to a properly grounded branch circuit, protected by a 15- or 20- amp circuit breaker or time-delay fuse. If electrical supply provid- ed does not meet the above specifications, it is reconnnended that a licensed electrician install an apt)roved outlet.

_WARNING - THIS DRYER IS EQUIPPED

A THREE-PRONG (GROUNDING) PLUG FOR YOUR PROTECTION AGAINST SHOCK

HAZARD AND SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE. DO NOT CUT

OR REMOVE THE GROUNDING PRONG

FROM THIS PLUG.

[] EXHAUST iNFORMATiON

_WARNING - USE ONLY METAL 4-IN. DUCT. DO NOT USE DUCT LONGER THAN SPECIFIED IN THE EXHAUST LENGTH TABLE.

Exhaust longer than specified will:

• Increase the drying times and the energy cost. " Reduce the dryer life.

• Accunmlate lint, creating a potential fire hazard.

The correct exhaust installation is your responsibility. Problems due to incorrect installation a,,e not covered

by the warranty.

The MAXIMUM ALLOWABLE length of the exhaust system depends upon the type of duct, number of turns, the type of exhaust hood (wall cap), and all conditions noted below-. Both rigid and flexible metal duct are shown in the table below:

EXHAUST LENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust HoodTypes

Recommended

No. of 90°

Elbows

2 3 4

If using flexible metal duct, please refer to page 6.

Rigid Flexible

Metal Metal

150 Feet 55 Feet 135 Feet 52 Feet 125 Feet 49 Feet

115 Feet 48 Feet 105 Feet 43 Feet 95 Feet 40 Feet

Use onlyfor short

run installations

4" DIA.

[_2-1/2"

Rigid Flexible Metal Metal

125 Feet 45 Feet 115 Feet 42 Feet 105 Feet 39 Feet

95 Feet 35 Feet 85 Feet 33 Feet

75 Feet 30 Feet

ENSURE PROPER GROUND EXISTS BEFORE USE.

IFLOCALCODESPERMIT,

ANEXTERNALGROUNDWIRE

(NOTPROVIDED},WHICHMEETS LOCALCODES,MAYBEADDED

BYATTACHINGTOTHEGREEN GROUNDSCREWONTHEREAR

OFTHEDRYER,ANDTOAGROUNDED

METALCOLDWATERPIPEOROTHER ESTABLISHEDGROUND.

EXHAUST SYSTEM CHECK LiST

HOOD OR WALL CAP

•Terminate in a manner to prevent back drafts or entry of birds or other wildlife.

•Termination should present minimal resistance to the exhaust air flow and should require little or no maintenance to prevent clogging.

•Never install a screen in or over the exhaust duct.

•Wall caps must be installed at least 12in. above ground level or any other obstruction with the opening pointed down.

•If roof vents or louvered plenmns are used, they must be equivalent to a 4-in. dampened wall cap in regard to resistance to air flow, prevention of back drafts, and maintenance required to prevent clogging.

SEPARATION OF TURNS

Fox'best perfbrmance, separate all turns by at least 4 fL of straight duct, including distance between last turn and dampened wall cap.

TURNS OTHER THAN 90°

• One turn of 45o or less may be ignored.

•Two 45 turns should be treated as one 90oturn.

•Each turn over 45 should be treated as one 00 turn.

SEALING OF JOINTS "All joints should be tight to avoid leaks. The male end of each section of

duct must point away fi'om the dryer.

*Do not assemble the ductwork with fasteners that extend into the duct.

They will serve as a collection point fbr lint.

"Duct joints should be made air-and moisture-tight by wrapping the

overlapped joints with duct tape.

"Horizontal runs should slope down towm'ds outdoors 1/2 inch pet"fbot.

INSULATION

•Duct work that runs through an unheated area or is near air conditioning should be insulated to reduce condensation and lint build up_

o o

Installation

[] EXHAUST CONNECTION

,_WARNING - TO REDUCE THE RISK

OF FIRE OR PERSONAL INJURY:

This dryer must be exhausted to the outdoors. Use only metal duct. Do not terminate exhaust in a chimney, any gas vent, under an enclosed floor (crawl space), or into an attic.

The accumulated lint could create a fire hazard.

Provide an access for inspection and cleaning of the exhaust system, especially at turns. Inspect and clean at least once a year.

Never terminate the exhaust into a common duct with a kitchen exhaust. A combination of lint and grease could

create a fire hazard.

Do not obstruct incoming or exhausted air.

WE RECOMMEND THAT YOU INSTALL YOUR DRYER

BEFOREYOUR WASHER. THIS WILL PERMIT DIRECT

ACCESS FOR EASIEREXHAUST CONNECTION

THIS DRYERCOMES READY FORREAREXHAUSTING. IF

SPACEIS LIMITED, USE THE INSTRUCTIONS IN SECTION 12 TO EXHAUST DIRECTLYFROM THE LEFTSIDE OR

BOTTOM OF THE CABINET.

Instructions

FORSTRAIGHT LINEINSTALLATION,

CONNECTTHE ELBOWHIGHLY

DRYEREXHAUST -_ RECOMMENDED.

TOTHEWALLUSING

DUCTTAPE,

RECOMMENDED CONFIGURATION TOMINIMIZE EXHAUST BLOCKAGE,

ELBOWHIGHLY RECOMMENDED,-

NOTE: ELBOWS WILL PREVENT DUCT KINKING AND COLLAPSING.

STANDARD REAR EXHAUST

[] LEVELING DRYER

LEVEL FRONT-TO-BACK.

_. LEVEL

4LEVELINGLEGS

SIDE-T0-SIDE

WESTRONGLYRECOMMENDTHEUSEOF RIGIDMETALEXHAUSTDUCT.IFUSING FLEXABLEMETALDUCT,CUTITTOTHEPROPER LENGTHANDAVOIDBUNCHINGOFTHEDUCT BEHINDTHEDRYER.

STANDTHEDRYERUPRIGHTNEARTHE

2ANTI-TIPLEGS

FINALLOCATIONANDADJUSTTHE4LEVELING LEGSTOMATCHTHEHEIGHTOFYOURWASHER, ADJUSTTHE2ANTI-TIPLEGSTOCONTACT THEFLOOR.

Installation instructions

USING FLEXIBLE METAL DUCTS

If rigid all metal duct cammt be used, then flexible all metal venting cart be used, but it will redtlce the maximum recommended duct length. In special installations when it is impossible to make connection with the above recomlnendations, then UL listed clothes dryer transition duct may be used as transition venting between the dryer and wall connection only. The use of this ducting will aflect dry time.

If flexible transition duct is necessary, the fbllowing directions must be followed.

• Use the Shortest Length Possible.

• Stretch the Duct to Its Maximmn Length.

• Do Not Crush or Collapse.

• Never Use _lYansition Duct Inside the Wall or Inside the Dryer.

• Avoid Resting the Duct on Sharp Objects.

• Venting Must Conform to Local BuiMing Codes.

[] ALCOVE OR CLOSET INSTALLATION

o If yore' dryer is approved for installation in an alcove or

closet, it will be stated on a label on the dryer back.

o The dryer MUST be vented to the outdoors. See the

EXHAUST INFORMATION section.

o Mininmm clearance between dryer cabinet and adjacent

walls or other surfaces is:

0 in. either side 3 in. fl'ont and rear

o Minimum vertical space from floor to overhead cabinets,

ceiling, etc. is 52 in.

o Closet doors must be louvered or otherwise ventilated and

mtlst contain a minimum of 60 sq in. of open area equally

distribmed. If the closet contains both a washer and a

dryer, doors nmst contain a mininmm of 120 sq in. of open area equally distributed

o The closet sbotfld be vented to the omdoors to prevent gas

pocketing in case of a gas leak in the supply line.

o No other tirol-burning appliance shall be installed in the

same closet with the dryer.

[] BATHROOM OR BEDROOM

INSTALLATION

ELBOWHIGHLY RECOMMENDED

DONOTUSE EXCESSIVE

ELBOWSHIGHLY

)(

_. CRUSH

D0,0T\

FLEXIBLE

N EXHAUST

_ AGAINST

o The dryer MUST be vented to the outdoors, See

EXHAUST INFORMATION section 6

o The installation nmst conform with local codes or, in the

absence of local codes, with the NATIONAL FUEL GAS CODE, ANSI Z223

[] MOBILE OR MANUFACTURED

HOME INSTALLATION

oInstallation must conform to the MANUFACTURED

HOME CONSTRUCTION & SAFETY STANDARD, TITLE 24, PART 32-80 or, when such standard is not

applicable, with AMERICAN NATIONAL STANDARD FOR MOBILE HOME, NO. 501B,

oThe dryer MUST be vented to the outdoors with the

termination securely fastened to the mobile home structure. (See EXHAUST INFORMATION section 6.)

oThe vent MUST NOT be terminated beneath a mobile or

manufactm'ed home.

oThe vent duct material MUST BE METAL. *KIT 14-D346-33 MUST be used to attach the dryer

securely to the structure

oThe vent MUST NOT be connected to any other duct,

vent, or chimney.

oDo not use sheet metal screws or other refastening

devices which extend into the interior of the exhaust vent.

oProvide an opening with a free area of at least 25 sq, in.

for introduction of outside air into the dryer room.

Installation Instructions:

[] DRYER EXHAUST TO RIGHT OR

BOTFOM CABINET

I--

IAkWARNING-BEFORE PERFORMING

THIS EXHAUST INSTALLATION, BE SURE TO DISCONNECT THE DRYER FROM ITS

ELECTRICAL SUPPLY. PROTECT YOUR HANDS AN DAR MS FROM S HARP EDGES

WHEN WORKING INSIDE TH E CABINET.

BE SURE TO WEAR GLOVES

REMOVE SCREW

ANDSAVE.

REMOVE DESIRED KNOCKOUT

(0NEONLY).

Detach and remove the bottom, right or left side knockout as desired. Remove the screw inside the dryer exhaust duct and save. Pull the duct out of the drye_

FIXINGHOLE

ADDING NEW DUCT

FIXING HOLE

PORTION"A"

Reconnect the cut portion (A) of the duct to the blower housing. Make sure that the shortened duct is aligned with the tab in the base. Use the screw saved previously to secure the duct in place through the tab on the appliance base.

ADDING ELBOW AND DUCT FOR

EXHAUST TO RIGHT SIDE OF CABINET

• Preassemble 4" elbowwith 4" duct. Wrap duct tape around joint.

• Insert duct assembly, elbow first, through the side opening and connect the elbow to the dryer internal duck

CAUTION: Be sure not to pull or damage the

electrical wires inside the dryer when inserting the duct,

B A

4 9"

Cut the duct as shown and keep portion A.

TAB LOCATION

BENDTAB UP45o

Through the rear opening, locate the tab in the middle of

the appliance base. Lift the t:ab to about 45 using a fiat blade screwdriver

l_ _i EXHAUST CAN

DUCT/ "-,4,/ RIGHTSIDE TAPE

•Apply duct tape as shown on thejoint between the dryer

internal duct and the elbow.

DUCT

CAUTION:

Internal duct joints must be

-_ secured with tape, otherwisethey may separate and cause

a safety hazard.

Installation

instructions

ADDING ELBOW FOR EXHAUST

THROUGH BOTTOM OF CABINET

• Insert the elbow through tile rear opening and connect it to tile dryer internal duct.

• Apply duct tape on the joint between the dryer internal duct and elbow, as shown on page 7.

CAUTION:

internal duct joints must be secured with tape, otherwise they may separate and cause a

safety hazard.

ADDING COVER PLATE TO REAR

OF CABINET

[] CHANGING DIRECTION OF

DOOR OPENING

REMOVE4HOLEPLUGSAND

REMOVE4 HINGESCREWS.

PLACETHEMINTHEHOLES ONTHEOPPOSITESIDE.

PLATE (KITWE1M454)

Connect standard metal elbows and ducts to complete the exhaust system. Cover back opening with a plate (Kit WE1M454) available from your local service provider. Place dryer in final location.

I '_WARNING- NEVER LEAVE THE I

BACK OPENING WITHOUT THE PLATE.

ROTATEDOOR1800 ANDREINSTALL.

[] SERViCiNG

_{k WARNING- LABEL ALL WIPES

PRIOR TO DISCONNECTION WHEN

SERVICING CONTROLS. WIRING

ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION AFTER

SERVICING/INSTALLATION.

For Questions on Installation, Call: 1-800-626-2000 (US) or

500A420P003 1-800-361-3400 (Canada). Pub. # 31-16139 8

For replacement parts and other information, refer to Owner's Manual for servicing phone numbers.

+ 16 hidden pages