Hotpoint HDI93X Instruction Manual

Instructions for use

HOOD

English

HDI 93 X

Contents

Installation, 10-11

Assembly

Technical information, 12

Electrical connection Technical data

Description, 13

Filtering version Ducting version

Operation, 14

Controls

Maintenance,15

Cleaning the hood Cleaning the grease filters Replacing the charcoal filter Replacing the lamps

Precautions and tips, 16

General safety Air vent Disposal

Installation

Assembly

Before proceeding with the assembly operations, remove the grease filters so that the hood is easier to handle (for the instructions see the paragraph

“Cleaning the grease filters” in the chapter on “Maintenance”).

1) Using the special drilling template, drill the holes for fixing to the ceiling on the vertical side of your hob. Carefully observe all the indications for final positioning of the apparatus. Take into account that one of the template axes must correspond to the axis of the hood controls.

2) Fix the bracket (A) to the ceiling using the screws and screw anchors provided. Be careful, because the position of the bracket determines the final position of the apparatus: the side with the slot B corresponds to the side opposite the controls.

4) Ducting version:

a) Take the upper flue (with the round slots) and

fit it on the telescopic structure with the slots facing upwards; fit the flue to the bracket with 2 screws (E).

b) Take the lower flue (F) and fit it in the same

manner as before; slide it to the top and stop it in that position using a adhesive tape.

c) Take the flange with the metal valve (G) and

assemble it onto the opening of the hood for air venting, pressing slightly.

3) Fix the telescopic structure to the bracket by means of 4 screws C (provided), running the air evacuation pipe through the telescopic structure and the electric power cable through the special hole in the bracket (the air evacuation pipe is not supplied). Set the height of the structure bearing in mind that the height of the hood is 56 mm and that the distance of the hood from the cooker must be at least 650 mm. Once the height is set, block the telescopic structure with 8 screws and 8 washers (D) – (2 screws and 2 washers on each side).

CAUTION: there is only 1 screw and 1 washer on the telescopic structure, take the other 7 from the accessories’ bag.

d) Fit the hood to the telescopic structure by

means of 4 screws H (provided). Through openings L fix the air evacuation pipe to flange G.

e) Make the electrical connection of the hood by

means of the power cable (refer to the paragraph “Electrical connection”).

f) Remove the adhesive tape and pull the lower

flue downwards, placing it gently onto the apparatus.

g) Check if the charcoal filter P has already been

installed; this filter is not necessary for the suction version, therefore it must be removed (see the instructions in the “Replacing the charcoal filter” chapter).

h) Installation is now complete and the grease

filters can be reassembled.

5) Filtering version:

a) Insert the air baffle (M) in the structure. b) Through the openings N, fit the flange (Q) to

the baffle (M) locking it with a turning movement. Fix a flexible pipe (R) to the flange (Q) for air evacuation (the flexible pipe s not supplied).

f) Fit the hood to the telescopic structure by

means of 4 screws H (provided).

g) Fix the air evacuation pipe (R) onto the

reduction (S).

h) Make the electrical connection of the hood by

means of the power cable (refer to the paragraph “Electrical connection”).

i) Remove the adhesive tape and pull the lower

flue downwards, placing it gently onto the apparatus.

l) Check if the charcoal filter P has already been

installed; this filter is necessary for the filtering version therefore it must be installed by inserting the 2 filter tabs into the relevant housing and turning in an upward direction.

c) Take the upper flue (with the round slots) and

fit it on the telescopic structure with the slots facing upwards; fit the flue to the bracket with 2 screws (E) - figure on previous page.

d) Take the lower flue (F) and fit it in the same

manner as before; slide it to the top and stop it in that position using a adhesive tape - figure on previous page.

e) Take the reduction (S) and assemble it onto

the air venting opening of the hood, pressing slightly.

m) Installation is now complete and the grease

filters can be reassembled.

+ 5 hidden pages