Instructions for Installation and Use
7kg Condenser Dryer Aquarius
CTD40
To the Installer:
Before installation, fill in the product details on the back cover of this book. The information can be found on the rating plate.
To the User:
You must read these instructions prior to installing and using the appliance and then retain them for future reference.
Important Information
For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below:
GB
Fluff filter...
! You MUST clean the fluff filter after EVERY drying cycle.
STEP 1. |
|
STEP 2. |
Open the door of your |
|
Pull out the filter (using |
dryer. |
|
the two finger grips). |
|
|
|
|
|
|
STEP 3.
Clean any fluff deposits from the filter mesh.
STEP 4.
Refit the filter - NEVER run the dryer without the filter in position.
!Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.
-It will take longer to dry and as a result will use more electricity during drying.
Water Container...
! You MUST empty the water container after EVERY drying cycle.
STEP 1. |
|
STEP 2. |
Pull the water container |
|
Empty all the water |
towards you and remove it |
|
collected in the water |
fully from the dryer. |
|
container. |
|
|
|
STEP 3.
Refit the water container, ensuring that it is pushed fully back into position.
! The ‘Empty Water’ light stays on - To remind you to empty the water container at the start and at the end of each drying cycle.
!Failure to empty the water container after EVERY drying cycle will result in:
-The machine will stop heating (so the load may still be wet at the end of the drying cycle).
-The ‘Empty Water’ light will flash to tell you that the water container is full.
Priming the Water Collection System
When your dryer is new, the water container will not collect water until the system is primed... this will take 1 or 2 drying cycles. Once primed it will collect water during every drying cycle.
2
Important Information
Condenser Unit...
! You MUST clean the fluff from the condenser EVERY month.
STEP 1.
Open the condenser cover - hold the handle and pull towards you.
Rotate 3 clips
STEP 2. |
|
STEP 3. |
|
STEP 4. |
||||||
Remove the condenser by |
|
Flush the condenser, from |
|
Refit the condenser unit |
||||||
rotating the 3 clips then |
|
the rear with water, to |
|
- ensure that the unit is |
||||||
pulling the condenser |
|
remove any fluff deposits. |
|
pushed in fully, all 3 clips |
||||||
towards you. |
|
|
|
are re-secured and the |
||||||
(There may be some water |
|
|
|
positiong arrows on the |
||||||
in the tubes, this is normal). |
|
|
|
front of the condenser are |
||||||
|
|
|
|
|
|
|
|
|
|
pointing upwards. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
●Check that:
-The positioning arrows are pointing upwards.
-The 3 clips are re-secured back into their ‘lock’ position.
! Failure to clean the condenser could cause premature failure of your dryer.
GB
Information |
Important |
|
|
Installation |
|
|
|
Description |
|
|
|
Programmes |
Startand |
|
|
Laundry |
|
|
|
Suggestions |
Warningsand |
|
|
andCare |
Maintenance |
|
|
Troubleshooting |
|
|
|
Service |
|
3
Instruction booklet
TUMBLE DRYER
GB |
|
GB |
|
Contents |
|
|
|
||
|
|
|
|
Installation, 5 |
|
|
English |
||
|
|
|
|
Where to put your dryer |
|
|
|
|
Ventilation |
|
|
|
|
Door reversal instructions |
|
|
|
|
Water drain |
|
|
|
|
Electrical connection |
|
|
|
|
Before you start using your dryer |
|
|
|
|
Dryer description, 6 |
|
|
|
|
To open the door |
|
|
|
|
The features |
|
|
|
|
Control panel |
|
|
|
|
Start and programmes, 7-9 |
|
|
|
|
Choosing a programme |
|
|
|
|
Table of programmes |
|
|
CTD40 |
The controls |
|
|
|
Option buttons / icons |
||
|
|
|
|
|
|
|
|
|
Door Opening |
|
|
|
|
Laundry, 10-11 |
|
|
|
|
Sorting your laundry |
|
|
|
|
Wash care labels |
|
|
|
|
Special clothing items |
|
|
|
|
Drying times |
|
|
|
|
Warnings and Suggestions, 12 |
|
|
|
|
General safety |
|
|
|
|
Disposal |
|
|
|
|
Saving energy and respecting the environment |
|
|
|
|
Maintenance and Care, 13 |
|
|
|
|
Switching off the electricity |
|
|
|
|
Cleaning the filter after each cycle |
|
|
|
|
Check the drum after each cycle |
|
|
|
|
Empty the water container after each cycle |
|
|
|
|
Cleaning the condenser unit |
|
|
|
|
Cleaning the dryer |
|
|
|
|
Troubleshooting, 14 |
|
|
|
|
Service, 15 |
!Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.
!Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works.
4
Installation
Where to put your dryer
●Place your dryer at a distance from gas ranges, stoves, heaters, or cook tops because flames can damage the appliance.
Minimum gap 10mm |
|
|
● |
If you are going to install the |
||
|
|
|
||||
|
|
|
|
|
|
appliance under a work |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
counter, be sure to leave a |
|
|
|
|
|
|
10mm space between the top |
|
|
|
|
and any other objects on or |
||
|
|
Minimum gaps |
|
|
||
|
|
15mm |
|
|
above the machine and a |
|
|
|
|
|
|
|
15mm space between the |
|
|
|
|
|
|
|
|
|
|
|
|
|
sides and lateral furnishings or |
|
|
|
|
|
|
walls. |
|
|
|
|
|
|
This is to ensure proper air circulation.
! Make sure that the back vents are not obstructed.
Ventilation
When the dryer is in use, there has to be adequate ventilation. Make sure you put your dryer in an environment that is not damp and has proper air circulation throughout. Airflow around the dryer is essential to condense the water produced during the washing, the dryer will not operate efficiently in an enclosed space or cupboard.
!If using the dryer in a small or cold room some condensation could be experienced.
!We do not recommend that the dryer is installed in a cupboard but the dryer must never be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the dryer door.
Door Reversal Instructions
|
|
Door catch |
Hinge |
||
|
|
|
Door latch
Hinge
The door of your dryer is reversible and can easily be changed. Exchange diagonally hinge brackets and blanking screws. Exchange door latch and catch with their opposite blanking plates (see diagram above).
Water drain
If your dryer is installed next to a drain the water can be plumbed into this drain. This does away with the need to empty the water container (see Plumbing your Dryer).
Electrical connections
Make sure of the following before you insert the plug into the the electrical socket:
●The socket must be grounded.
●The socket must be able to sustain the machines maximum power, which is indicated on the rating label (see Dryer Description).
●Power voltage must be within the values indicated on the rating label (see Dryer Description).
●The socket must be compatible with the dryers plug.
●Should this not be the case,replace the plug or the socket. ! Do not use extension cords.
! The dryer must not be installed outdoors, even if the space is sheltered. It can be very dangerous if it is exposed to rain or storms.
! Once installed, the dryers electrical wire and plug must be within easy reach.
! The power cord must not be bent or squashed.
! The power cord supplied is fitted with a BS1363 plug and a 13 amp BS1362 fuse. If you need to replace the fuse, use only those rated at 13 amp (13A) and ASTA approved to BS1362.
Moulded plug
! The plug must not be used without the fuse cover in place. If a replacement fuse holder/cover is required, it must be of the same colour coding or wording as shown on the base of the plug.
Replacements are available from authorised dealers.
Changing the plug
The wires in the power cord are coloured in accordance with the following:
Green and Yellow |
|
|
|
|
|
|
|
||||||
(Earth) wire to terminal |
|
|
|
|
|
|
|
||||||
marked ‘E’, symbol |
|
|
, |
|
|
|
|
|
|
|
|||
or coloured green and |
|
|
|
|
|
|
|
||||||
yellow. |
|
|
|
|
|
|
|
|
|
|
13A ASTA approved |
||
|
|
|
|
|
|
|
|
|
|
||||
Blue (Neutral) wire to |
|
|
|
|
|
|
fuse to BS1362. |
||||||
|
|
|
|
|
|
|
|||||||
terminal marked ‘N’ or |
|
|
|
|
|
|
|
Brown (Live) wire to |
|||||
|
|
|
|
|
|
|
|||||||
coloured black. |
|
|
|
|
|
|
terminal marked ‘L’ |
||||||
|
Cord clamp |
|
|
|
|
|
|
|
or coloured red. |
||||
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
!If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock
hazard.
!The power supply cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorised technicians (see Service). New or longer power cords are supplied at an extra charge by authorised dealers.
!The manufacturer denies any responsibility should any of these rules not be followed.
!If in doubt about any of the above consult a qualified electrician.
Before you start using your dryer
Once you have installed your dryer and before you use it, clean the inside of the drum to remove any dust that could have accumulated during transport.
GB
Information |
Important |
|
|
Installation |
|
|
|
Description |
|
|
|
Programmes |
Startand |
|
|
Laundry |
|
|
|
Suggestions |
Warningsand |
|
|
andCare |
Maintenance |
|
|
Troubleshooting |
|
|
|
Service |
|
|
|
5