HOTPOINT CRC641DB, CRC741DB, CRC740C User Manual

Instructions for Installation and Use

GLASS-CERAMIC HOB

CRC 741 D B

CRC 642 D B

CRC 641 D B

CRC 740 C

English

GB

Operating Instructions

HOB Contents

Operating Instructions,1 WARNING,1

Description of the appliance-Control Panel,2 Installation,3

Start-up and use,6 Precautions and tips,9 Care and maintenance,10

Technical description of the models,10

WARNING!

•WARNING: The appliance and its accessible parts become hot during use.

•Care should be taken to avoid touching heating elements.

•Children less than 8 years of age shall be kept away unless continuously supervised.

•This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

•WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.

•NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

•WARNING: Danger of fire: do not store items on the cooking surfaces.

•WARNING: If the surface in glassceramic is cracked, switch off the appliance to avoid the possibility of electric shock.

•Never use steam cleaners or pressure cleaners on the appliance.

•The appliance is not intended to be operated by means of an external timer or separate remote control system.

		us	on
			24
	phone 24
			your
		24
	Please08448activate
	to	guarantee

		Description of the appliance
	GB
		Control panel

5 3

1

13

9

10

6

7

12

4

2

8

11

The control panel described in this manual is only a representative example: it may not exactly match the panelon your appliance.

1INCREASE POWER button switches on the hotplate and controls the power (see Start-up and use).

2REDUCE POWER button controls the power and switches off the hotplate (see Start-up and use).

3COOKING ZONE SELECTOR indicator shows a particular cooking zone has been selected and therefore various adjustments are possible.

4COOKING ZONE SELECTOR button is used to select the desired cooking zone.

5POWER indicator provides a visual display for the current heat level.

6ON/OFF button switches the appliance on and off.

7ON/OFF indicator light shows whether the appliance is on or off.

8PROGRAMME TIMER* button controls the cooking programme times (see Start-up and use).

9 PROGRAMME TIMER display shows which programme has been selected (see Start-up and use).

10COOKING ZONE PROGRAMMED* indicator lights show which cooking zones are being used during a cooking programme (see Start-up and use).

11CONTROL PANEL LOCK button prevents accidental changes to the hob settings (see Start-up and use)..

12CONTROL PANEL LOCK indicator light shows the control panel has been locked (see Start-up and use)..

13TIMER* indicator light shows that the timer has been activated

! This product complies with the requirements of the latest European Directive on the limitation of power consumption of the standby mode. If no operations are carried out for a period of 2 minutes, after the residual heat indicator lights turn off and the fan stops (if present), the appliance automatically switches to the .off mode.. The appliance resumes the operating mode once the ON/OFF button is pressed.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

2

Installation

!Before operating your new appliance please read this instruction booklet carefully. It contains important information concerning the safe operation, installation and maintenance of the appliance.

!Please keep these operating instructions for future reference. Pass them on to any new owners of the appliance.

Positioning

! Keep all packaging material out of the reach of children. It may present a choking or suffocation hazard (see

Precautions and tips).

! The appliance must be installed by a qualified professional in accordance with the instructions provided. Incorrect installation may cause harm to people and animals or may damage property.

Built-in appliance

Use a suitable cabinet to ensure that the appliance functions properly.

•The supporting surface must be heat-resistant up to a temperature of approximately 100°C.

•If the appliance is to be installed above an oven, the oven must be equipped with a forced ventilation cooling system.

•Avoid installing the hob above a dishwasher: if this cannot be avoided, place a waterproof separation device between the two appliances.

•Depending on the hob you want to install, the cabinet must have the following dimensions (see figure):

			590					690
48					48
				520					520
				1					1
									-
				-	560				+/
560				+/				490
			490			+/-
	+/-						1
		1

Ventilation

To allow adequate ventilation and to avoid overheating of the surrounding surfaces the hob should be positioned as follows:

•At a minimum distance of 40 mm from the back panel.

•So that a minimum distance of 20 mm is maintained between the installation cavity and the cabinet underneath.

•Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 600 mm from

the edge of the hob.

GB

min. 20 mm

mm5 COMPARTMENT

min. 40 mm

min. 20 mm

5 mm

FAN-ASSISTED

OVEN

min. 40 mm

FRONT SIDE

OF HOB

SUPPORTING
SURFACE	30
		40

UNDERSIDE

OF HOB

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

3

		Fixing
	GB
		The appliance must be installed on a perfectly level
		supporting surface.
		Any deformities caused by improper fixing could affect
		the features and operation of the hob.
		The thickness of the supporting surface should be taken
		into account when choosing the length of the screws for
		the fixing hooks:
		•	30 mm thick: 17.5 mm screws
		•	40 mm thick: 7.5 mm screws

Fix the hob as follows:

1.Use short flat-bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob.

2.Place the hob in the cavity, make sure it is in a central position and push down on the whole perimeter until the hob is stuck to the supporting surface.

3.For hobs with raised sides: After inserting the hob into its cavity, insert the 4 fixing hooks (each has its own pin) into the lower edges of the hob, using the long pointed screws to fix them in place, until the glass is stuck to the supporting surface.

!The screws for the alignment springs must remain accessible.

!In order to adhere to safety standards, the appliance must not come into contact with electrical parts once it has been installed.

!All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.

Electrical connection

! The electrical connection for the hob and for any builtin oven must be carried out separately, both for safety purposes and to make extracting the oven easier.

Terminal board

UNDERSIDE OF HOB

On the lower part of the appliance there is a connection box for the different types of electricity supply (the picture is only an indication and is not an exact representation of the purchased model).

Single-phase connection

The hob is equipped with a pre-connected electricity supply cable, which is designed for single-phase connection. Connect the wires in accordance with the instructions given in the following table and diagrams:

	Voltage and	Electrical cable	Wire connection
	mains frequency
	230-240V 1+N ~		: yellow/green
			N: the two blue wires together
	220-240V 1+N ~
			L: brown and black together
	50/60 Hz

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

•400V - 2+N ~ 50/60 Hz

•220-240V 3 ~ 50/60 Hz

•230-240V 3 ~ 50/60 Hz

•400V - 2+2N ~ 50/60 Hz

Separate the wires and connect them in accordance with the instructions given in the following table and diagrams:

	Voltage and	Electrical cable	Wire connection
	mains frequency
	400V - 2+N ~		: yellow/green;
	50/60 Hz		N: the two blue wires
	230-240V 3 ~		together
	220-240V 3 ~		L1: black
	50/60 Hz		L2: brown
			: yellow/green;
	400V - 2+2N ~		N1: blue
	50/60 Hz		N2: blue
			L1: black
			L2: brown

If the mains supply corresponds with one of the following: Voltage and mains frequency

• 400V 3 - N ~ 50/60 Hz proceed as follows:

! The cable provided is not suitable for the following types of installation.

1.Use a suitable supply cable, H05RR-F or higher, with the right dimensions (cable cross section: 25 mm).

2.To open the terminal board, use a screwdriver as a lever under the side tabs of the cover (see Terminal

board picture).

3.Loosen the cable clamp screw and the terminal board screws in accordance with the type of connection required and position the connection supports as shown in the following table and diagrams.

4.Position the wires in accordance with the information given in the following table and diagrams and connect the appliance by tightening all the screws for the springs as much as possible.

Voltage and	Electrical connections	Terminal board
mains frequency
400V 3-N ~		Three-phase 400
50/60 Hz

5. Secure the power supply cable by fastening the cable clamp screw, then put the cover back on.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

4