Hosiden HRM1034 User Manual

User manual

Contains Transmitter Module FCC ID: VIYHRM1034

Contains FCC ID: VIYHRM1034

Contains Transmitter Module IC: 7305A-HRM1034

Contains IC: 7305A-HRM1034

Product: Bluetooth module
Model: HRM1034

For OEM integration only – device cannot be sold to general public.
Therefore we will not supply the User’s manual, the installation manual is the official for OEM.

FCC ID: VIYHRM1034
IC: 7305A-HRM1034

■Operational Information

This module has been tested and found to comply with the limits for a Class B digital device
pursuant to Part15 of FCC rules. This module complies with Part15 subpart C of the FCC
rules. Customers should check Part15 subpart B compliance with their own final products
and conduct certification if needed.

■Caution

Any changes or modifications are not expressly approved by Hosiden responsible for
compliance could void the user’s authority to operate the equipment.

■Requirement of Labeling

Please describe the following item on the final product including this module:

or

or

■Requirement of User’s Manual Statement

“This transmitter must not be co-located or operated in conjunction with any other antenna

or transmitter.”

The following statements must be described on the user manual of the host device of

this module;

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

Radiation Exposure Statement:

・For Mobile Use

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment has very low levels of RF energy that it deemed to
comply without maximum permissive exposure evaluation (MPE).

・For Portable Use

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment has very low levels of RF energy that are deemed to
comply without testing of specific absorption rate(SAR).

This device is intended only for OEM integrators under the following
conditions:

1) The transmitter module may not be co-located with any other transmitter or

antenna.

As long as 1 condition above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed

IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate
FCC authorization.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end

user regarding how to install or remove this RF module in the user’s

manual of the end product which integrates this module.

The end user manual shall include all required regulatory information/warning as
show in this manual.