Hoshizaki KM-1600MRH, KM-1600MRH3 Installation Manual

Reliability is a
beautiful thing

TM

MODULAR CRESCENT CUBER

KM-1600MRH
KM-1600MRH3

INSTRUCTION MANUAL

™

ISSUED:

REVISED:

FEB. 28, 2001

DEC. 11, 2003

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

Only qualified service technicians should attempt to install, service or maintain this
icemaker. No installation, service or maintenance should be undertaken until the
technician has thoroughly read this Instruction Manual. Likewise, the owner/manager
should not proceed to operate the icemaker until the installer has instructed them on
its proper operation.

HOSHIZAKI provides this manual primarily to assist qualified service technicians in the
installation, maintenance and service of the icemaker.

Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call or write HOSHIZAKI Technical Support for assistance.

HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City , Georgia 30269
Attn: HOSHIZAKI T echnical Support Dep artment

Phone: [phone] T echnical Service

[phone]

Fax: [phone]

NOTE:NOTE:

NOTE: To expedite assistance, all correspondence/communication MUST include the

NOTE:NOTE:

following information:

• Model Number

• Serial Number

• Complete and detailed explanation of the problem

2

• Please review this manual. It should be read carefully before the icemaker is installed and
operated. Only qualified service technicians should install, service and maintain the
icemaker. This manual should be made available to the technician prior to installation,
maintenance or service.

• Keep this manual with the icemaker for later reference.

CONTENTSCONTENTS

CONTENTS PAGE

CONTENTSCONTENTS

I. SPECIFICATIONS .................................................................................................. 4

1. NAMEPLATE RATING ......................................................................................... 4

[a] KM-1600MRH (Remote Air-cooled).................................................................4

[b] KM-1600MRH3 (Remote Air-cooled)...............................................................5

2. DIMENSIONS/CONNECTIONS ........................................................................... 6

II. INSTALLATION AND OPERATING INSTRUCTIONS........................................... 7

1. CHECKS BEFORE INSTALLATION.................................................................... 7

2. HOW TO REMOVE PANELS ...............................................................................7

3. LOCATION ...........................................................................................................8

4. SET UP ................................................................................................................ 8

5. ELECTRICAL CONNECTION............................................................................ 10

6. INSTALLATION OF REMOTE CONDENSER UNIT .......................................... 11

[a] CHECKS BEFORE INSTALLATION ............................................................. 1 1

[b] LOCATION ....................................................................................................11

[c] SET UP..........................................................................................................12

[d] ELECTRICAL CONNECTION ....................................................................... 1 3

[e] STACKING CONDENSER UNIT ..................................................................14

7. WATER SUPPLY AND DRAIN CONNECTIONS .............................................. 15

8. FINAL CHECK LIST ........................................................................................... 1 7

9. START UP..........................................................................................................18

10. PREPARING THE ICEMAKER FOR LONG STORAGE....................................1 9

III. CLEANING AND MAINTENANCE INSTRUCTIONS ..........................................21

1. CLEANING INSTRUCTIONS ............................................................................. 21

[a] CLEANING PROCEDURE.............................................................................22

[b] SANITIZING PROCEDURE ...........................................................................23

2. MAINTENANCE INSTRUCTIONS ..................................................................... 25

3

I. SPECIFICATIONSI. SPECIFICATIONS

I. SPECIFICATIONS

I. SPECIFICATIONSI. SPECIFICATIONS

1. NAMEPLATE RATING1. NAMEPLATE RATING

1. NAMEPLATE RATING

1. NAMEPLATE RATING1. NAMEPLATE RATING

[a] KM-1600MRH (Remote Air-cooled)[a] KM-1600MRH (Remote Air-cooled)

[a] KM-1600MRH (Remote Air-cooled)

[a] KM-1600MRH (Remote Air-cooled)[a] KM-1600MRH (Remote Air-cooled)

See the Nameplate for electrical and refrigeration specifi­cations. This Nameplate is located on the upper right hand
side of rear panel.

Since this Nameplate is located on the rear panel of the
icemaker, it cannot be read when the back of the icemaker
is against a wall or against another piece of kitchen
equipment. Therefore, the necessary electrical and refrig­eration information is also on the rating label, which can be
easily seen by removing only the front panel of the ice­maker.

We reserve the right to make changes in specifications and design without prior notice.

4

[b] KM-1600MRH3 (Remote Air-cooled)[b] KM-1600MRH3 (Remote Air-cooled)

[b] KM-1600MRH3 (Remote Air-cooled)

[b] KM-1600MRH3 (Remote Air-cooled)[b] KM-1600MRH3 (Remote Air-cooled)

See the Nameplate for electrical and refrigeration specifi­cations. This Nameplate is located on the upper right hand
side of rear panel.

Since this Nameplate is located on the rear panel of the
icemaker, it cannot be read when the back of the icemaker
is against a wall or against another piece of kitchen
equipment. Therefore, the necessary electrical and refrig­eration information is also on the rating label, which can be
easily seen by removing only the front panel of the ice­maker.

We reserve the right to make changes in specifications and design without prior notice.

5

2. DIMENSIONS/CONNECTIONS2. DIMENSIONS/CONNECTIONS

2. DIMENSIONS/CONNECTIONS

2. DIMENSIONS/CONNECTIONS2. DIMENSIONS/CONNECTIONS

units: mm. (inches)

6

II. INSTALLATION AND OPERATING INSTRUCTIONSII. INSTALLATION AND OPERATING INSTRUCTIONS

II. INSTALLATION AND OPERATING INSTRUCTIONS

II. INSTALLATION AND OPERATING INSTRUCTIONSII. INSTALLATION AND OPERATING INSTRUCTIONS

1. CHECKS BEFORE INSTALLATION1. CHECKS BEFORE INSTALLATION

1. CHECKS BEFORE INSTALLATION

1. CHECKS BEFORE INSTALLATION1. CHECKS BEFORE INSTALLATION
IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

1. Remove shipping carton, tape(s) and packing. If packing material is left in
the icemaker, it will not work properly.

2. Ensure all components, fasteners and thumbscrews are securely in place.

1) Remove the panels to prevent damage when installing the icemaker. (See “2. HOW TO

REMOVE PANELS.”)

2) Remove the package containing the accessories.

3) Remove the protective plastic film from the panels. If the icemaker is exposed to the sun

or to heat, remove the film after the icemaker cools.

4) Check that the refrigerant lines do not rub or touch lines or other surfaces.

5) Check that the Compressor is snug on all mounting pads.

6) See the Nameplate on the Rear Panel, and check that your voltage supplied corresponds

with the voltage specified on the Nameplate.

7) This icemaker needs a storage bin. The recommended storage bin is HOSHIZAKI ICE

STORAGE BIN, Model B-500 series.

8) A remote condenser unit is needed. The recommended remote condenser unit is

HOSHIZAKI CONDENSER UNIT, Model URC-20F.

2. HOW TO REMOVE PANELS - See Fig. 12. HOW TO REMOVE PANELS - See Fig. 1

2. HOW TO REMOVE PANELS - See Fig. 1

2. HOW TO REMOVE PANELS - See Fig. 12. HOW TO REMOVE PANELS - See Fig. 1

a) Front Panel ......... Remove the screw.

Lift up and pull toward you.

b) Top Panel............ Lift up slightly its front, push

away, and then lift off.

c) Side Panel (R)..... Remove the screw.

Pull slightly toward you, and
lift off.

Fig. 1Fig. 1

Fig. 1

Fig. 1Fig. 1

d) Insulation Panel ... Lift up slightly, and pull toward you.
Note: If the Top Panel is still on, first lift it and slide it to the back

slightly.

7

3. LOCATION3. LOCATION

3. LOCATION

3. LOCATION3. LOCATION
WARNINGWARNING

WARNING

WARNINGWARNING

This icemaker is not intended for outdoor use. Normal operating ambient
temperature should be within +45°F to +100°F; Normal operating water
temperature should be within +45°F to +90°F. Operation of the icemaker, for
extended periods, outside of these normal temperature ranges may affect
production capacity.

For best operating results:

• Icemaker should not be located next to ovens, grills or other high heat producing

equipment.

• Location should provide a firm and level foundation for the equipment.

• Allow 6" clearance at rear, sides and top for proper air circulation and ease of maintenance

and/or service should they be required.

4. SET UP4. SET UP

4. SET UP

4. SET UP4. SET UP

1) Unpack the Storage Bin, and attach the four adjustable legs provided (bin accessory) to

the bottom of the Storage Bin.

2) Position the Storage Bin in the selected permanent position.

3) Place the icemaker on top of the Storage Bin.

4) Secure the icemaker to the Storage Bin by using the two Universal Braces and the two

bolts provided. See Fig. 2.

Fig. 2Fig. 2

Fig. 2

Fig. 2Fig. 2

8