Hoshizaki F-450MAF Manuel de service

NO:
ISSUED:
REVISED:

73073

DEC. 8, 1998

DEC. 15, 2003

HOSHIZAKI

MODULAR FLAKER

MODEL F-450MAF(-C)

SERVICE MANUAL

IMPORTANT

Only qualified service technicians should attempt to service or maintain this icemaker.
No service or maintenance should be undertaken until the technician has thoroughly
read this Service Manual.

HOSHIZAKI provides this manual primarily to assist qualified service technicians in the
service and maintenance of the icemaker.

Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call or write to the HOSHIZAKI Technical Support Department for
assistance.

HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City , GA 30269

Attn: HOSHIZAKI T echnical Support Department

Phone: [phone] T echnical Service

[phone]

Fax: [phone]

NOTE: T o expedite assistance, all correspondence/communication MUST include the following

information:

• Model Number

• Serial Number

• Complete and detailed explanation of the problem

2

Please review this manual. It should be read carefully before the icemaker is serviced or
maintenance operations are performed. Only qualified service technicians should service
and maintain the icemaker. This manual should be made available to the technician prior

to service or maintenance.

CONTENTS

PAGE

I. SPECIFICATIONS ............................................................................................................ 5

1. F-450MAF ................................................................................................................... 5

2. F-450MAF-C ............................................................................................................... 6

II. GENERAL INFORMATION .............................................................................................. 7

1. CONSTRUCTION ....................................................................................................... 7

2. CONTROL BOX LAYOUT........................................................................................... 8

3. TIMER BOARD ......................................................................................................... 10

[a] SOLID-STATE CONTROL .................................................................................. 10

[b] TIMER BOARD ................................................................................................... 10

[c] SEQUENCE ........................................................................................................ 11

III. TECHNICAL INFORMATION....................................................................................... 14

1. WATER CIRCUIT AND REFRIGERATION CIRCUIT............................................... 14

2. WIRING DIAGRAMS................................................................................................. 15

[a] F-450MAF ........................................................................................................... 15

[b] F-450MAF-C ....................................................................................................... 16

3. SEQUENCE OF ELECTRICAL CIRCUIT ................................................................. 17

4. TIMING CHART ........................................................................................................ 27

5. PERFORMANCE DATA............................................................................................ 30

[a] F-450MAF ........................................................................................................... 30

[b] F-450MAF-C ....................................................................................................... 31

IV. SERVICE DIAGNOSIS ................................................................................................ 32

1. NO ICE PRODUCTION............................................................................................. 32

2. LOW ICE PRODUCTION.......................................................................................... 35

3. OTHERS ................................................................................................................... 36

V. REMOVAL AND REPLACEMENT OF COMPONENTS ............................................... 37

1. SERVICE FOR REFRIGERANT LINES.................................................................... 37

[a] REFRIGERANT RECOVERY ............................................................................. 37

[b] EVACUATION AND RECHARGE....................................................................... 37

2. BRAZING .................................................................................................................. 38

3. REMOVAL AND REPLACEMENT OF COMPRESSOR ........................................... 39

4. REMOVAL AND REPLACEMENT OF DRIER.......................................................... 40

5. REMOVAL AND REPLACEMENT OF EXPANSION VALVE ................................... 41

6. REMOVAL AND REPLACEMENT OF EVAPORATOR ASSEMBLY........................ 42

7. REMOVAL AND REPLACEMENT OF FAN MOTOR ............................................... 44

3

8. REMOVAL AND REPLACEMENT OF CONTROL WATER VALVE......................... 44

9. REMOVAL AND REPLACEMENT OF FLUSH WATER VALVE............................... 45

VI. MAINTENANCE AND CLEANING INSTRUCTIONS ...................................................... 47

1. PREPARING THE ICEMAKER FOR LONG STORAGE ............................................ 47

2. CLEANING INSTRUCTIONS .................................................................................... 48

3. MAINTENANCE INSTRUCTIONS............................................................................. 53

4

I. SPECIFICATIONS

1. F-450MAF

AC SUPPLY VOLTAGE 115/60/1
COMPRESSOR 120 V 8.5 RLA 51 LRA
GEAR MOTOR 120 V 1.6 FLA 1/6 HP
FAN MOTOR 115 V 0.85FLA 50W
OTHER 120 V 0.03A
MAXIMUM FUSE SIZE 20 A
MAX. HACR BREAKER (USA ONLY) 20 A
MAX. CIRC. BREAKER (CANADA ONLY) 20 A
MINIMUM CIRCUIT AMPACITY 20 A
APPROXIMATE ICE PRODUCTION Ambient WATER TEMP. (°F)
PER 24 HR. Temp.(°F)507090
lbs./day ( kg/day ) 70 *476 (216) 456 (207) 435 (197)
Reference without *marks 80 416 (189) 397 (180) 379 (172)

90 362 (164) *355 (161) 330 (150)

100 315 (143) 301 (137) 282 (128)
SHAPE OF ICE Flake
ICE QUALITY Approx. 70%, Ice (90/70°F, Conductivity 200 µs/cm)
APPROXIMATE STORAGE CAPACITY N/A
ELECTRIC & WATER CONSUMPTION 90/70°F 70/50°F
ELECTRIC W (kWH/100 lbs.) 915 (6.2) 858 (4.3)
POTABLE WATER 43 (12) 57 (12)
gal./24HR (gal./100 lbs.)
EXTERIOR DIMENSIONS (WxDxH) 21"-7/8" x 27-3/8" x 21-61/64" (556 x 696 x 557.7mm)
EXTERIOR FINISH Stainless Steel, Galvanized Steel (Rear)
WEIGHT Net 150 lbs. ( 68 kg ), Shipping 187 lbs. ( 85 kg )
CONNECTIONS - ELECTRIC Permanent - Connection

- WATER SUPPLY Inlet 1/2" FPT

- DRAIN Outlet 3/4" FPT
ICE MAKING SYSTEM Auger type
HARVESTING SYSTEM Direct Driven Auger ( 1/6 HP Gear Motor )
ICE MAKING WATER CONTROL Float Switch
COOLING WATER CONTROL N/A
BIN CONTROL SYSTEM Mechanical Bin Control ( Proximity Sw. )
COMPRESSOR Hermetic, Model RS43C1E-CAA-219
CONDENSER Air-cooled, Fin and tube type
EVAPORATOR Copper Tube on Cylinder
REFRIGERANT CONTROL Thermostatic Expansion Valve
REFRIGERANT CHARGE R-404A, 1 lb. (455 g)
DESIGN PRESSURE High 427 PSIG, Low 230 PSIG
P.C. BOARD CIRCUIT PROTECTION High Voltage Cut-off Relay
COMPRESSOR PROTECTION Internal Protector
GEAR MOTOR PROTECTION Manual reset Circuit Breaker or Fuse
REFRIGERANT CIRCUIT PROTECTION Auto-reset High Pressure Control Switch
LOW WATER PROTECTION Float Switch and Timer
ACCESSORIES - REQUIRED Ice Storage Bin
OPERATING CONDITIONS VOLTAGE RANGE 104 - 127 V

AMBIENT TEMP. 45 - 100° F
WATER SUPPLY TEMP. 45 - 90° F
WATER SUPPLY PRESSURE 10 - 113 PSIG

DRAWING NO. (DIMENSION) 3A0872

We reserve the right to make changes in specifications and design without prior notice.

5

2. F-450MAF-C

AC SUPPLY VOLTAGE 115/60/1
COMPRESSOR 120 V 8.5 RLA 51 LRA
GEAR MOTOR 120 V 1.6 FLA 1/6 HP
FAN MOTOR 115 V 0.85FLA 50W
OTHER 120 V 0.03A
MAXIMUM FUSE SIZE 20 A
MAX. HACR BREAKER (USA ONLY) 20 A
MAX. CIRC. BREAKER (CANADA ONLY) 20 A
MINIMUM CIRCUIT AMPACITY 20 A
APPROXIMATE ICE PRODUCTION Ambient WATER TEMP. (°F)
PER 24 HR. Temp.(°F)507090
lbs./day ( kg/day ) 70 *426 (193) 407 (185) 387 (176)
Reference without *marks 80 368 (167) 350 (159) 333 (151)

90 317 (144) *310 (141) 287 (130)

100 273 (124) 260 (118) 244 (111)
SHAPE OF ICE Flake
ICE QUALITY Approx. 80%, Ice (90/70°F, Conductivity 200 µs/cm)
APPROXIMATE STORAGE CAPACITY N/A
ELECTRIC & WATER CONSUMPTION 90/70°F 70/50°F
ELECTRIC W (kWH/100 lbs.) 956 (7.4) 880 (5.0)
POTABLE WATER 37 (12) 51 (12)
gal./24HR (gal./100 lbs.)
EXTERIOR DIMENSIONS (WxDxH) 21"-7/8" x 27-3/8" x 21-61/64" (556 x 696 x 557.7mm)
EXTERIOR FINISH Stainless Steel, Galvanized Steel (Rear)
WEIGHT Net 150 lbs. ( 68 kg ), Shipping 187 lbs. ( 85 kg )
CONNECTIONS - ELECTRIC Permanent - Connection

- WATER SUPPLY Inlet 1/2" FPT

- DRAIN Outlet 3/4" FPT
ICE MAKING SYSTEM Auger type
HARVESTING SYSTEM Direct Driven Auger ( 1/6 HP Gear Motor )
ICE MAKING WATER CONTROL Float Switch
COOLING WATER CONTROL N/A
BIN CONTROL SYSTEM Infrared Sensor
COMPRESSOR Hermetic, Model RS43C1E-CAA-219
CONDENSER Air-cooled, Fin and tube type
EVAPORATOR Copper Tube on Cylinder
REFRIGERANT CONTROL Thermostatic Expansion Valve
REFRIGERANT CHARGE R-404A, 1 lb. (455 g)
DESIGN PRESSURE High 427 PSIG, Low 230 PSIG
P.C. BOARD CIRCUIT PROTECTION High Voltage Cut-off Relay
COMPRESSOR PROTECTION Internal Protector
GEAR MOTOR PROTECTION Manual reset Circuit Breaker or Fuse
REFRIGERANT CIRCUIT PROTECTION Auto-reset High Pressure Control Switch
LOW WATER PROTECTION Float Switch and Timer
ACCESSORIES - REQUIRED Ice Storage Bin
OPERATING CONDITIONS VOLTAGE RANGE 104 - 127 V

AMBIENT TEMP. 45 - 100° F
WATER SUPPLY TEMP. 45 - 90° F
WATER SUPPLY PRESSURE 10 - 113 PSIG

DRAWING NO. (DIMENSION) 3A0872

We reserve the right to make changes in specifications and design without prior notice.

6

II. GENERAL INFORMATION

1. CONSTRUCTION

Control Water Valve

Water Supply
Inlet

Bin Control

Ice Chute

Evaporator

Flush Water
Valve

Control Box

Gear Motor

Junction Box

Condenser

Fan Motor

Compressor

Drier

7

2. CONTROL BOX LAYOUT

For models with serial numbers H00001 to H00025.

Note: The above component names are identical with the Wiring Label, but not with

the Parts List.

8

For models with serial numbers beyond H00026.

Note: The above component names are identical with the Wiring Label, but not with

the Parts List.

9

3. TIMER BOARD

[a] SOLID-STATE CONTROL

1) A HOSHIZAKI exclusive solid-state control is employed in the self-contained flaker
icemakers.

2) A Printed Circuit Board (hereafter called “Timer Board”) includes a stable and high
quality control system.

3) All models are pre-tested and factory-adjusted.

[b] TIMER BOARD

CAUTION

1. Fragile, handle very carefully.

2. A timer board contains CMOS (Complementary Metal-Oxide Semicon­ductor) integrated circuits, which are susceptible to failure due to static
discharge. It is especially important to use an anti-static wrist strap
when handling or replacing the board.

3. Do not touch the electronic devices on the board or the back of the
board to prevent damage to the board.

4. Do not change wiring and connections. Especially, never misconnect
terminals.

5. Do not fix the electronic devices or parts on the board in the field. Al­ways replace the whole board assembly when it goes bad.

The icemaker is controlled by the Timer Board for the following purposes:

1) To prevent the Gear Motor and the Compressor from starting or stopping simulta­neously.

2) To reduce remaining ice in the refrigeration casing.

3) To protect the unit in case of low water and low water pressure.

4) To protect the unit in case the Bin Control causes chattering.

10

[c] SEQUENCE

Fig. 1

Fig. 2

11

EDOCTRAP10-503734

LEDOM10C441AA2H

GNITARzH06/05CAV42

1T.ces51±06
2T.ces22±09
3T.ces54±051
4Tsselro.ces1
5T%07±.ces7.6
6T%07±.ces7.6

Fig. 3

12

Functions of Terminals

1) Terminals 1, 2
Power supply AC 24V.

2) Terminals 3, 4
Control X1 (GM) and X2 (CM) Relays.
When closed, energize X1 (GM) in 1 sec. and X2 (CM) in 60 sec.
When opened, de-energize X

1 (GM) in 150 sec. and X2 (CM) in 90 sec.

3) Terminals 5, 6
Control X

1 (GM) and X2 (CM) Relays.

When opened, de-energize X1 (GM) and X2 (CM) immediately.
When closed again, energize X1 (GM) in 1 sec. and X2 (CM) in 60 sec.

4) Terminals 7, 8, 9
X1 (GM) contacts.
8 is a movable contact, 7 is a make contact, and 9 is a break contact.

5) Terminals 10, 11
Control X2 (CM) Relays.
When opened, de-energize X2 (CM) immediately.
When closed, energize X2 (CM) immediately.

Note: 1. X2 Relay is a single pole, normally open relay, and its terminals are mounted

on the relay itself.

2. The above operation times are median. See Fig. 3 for details.

13

III. TECHNICAL INFORMATION

1. W ATER CIRCUIT AND REFRIGERATION CIRCUIT

14

2. WIRING DIAGRAM

[a] F-450MAF

15

[b] F-450MAF-C

16

3. SEQUENCE OF ELECTRICAL CIRCUIT

[a] When Power Switch is moved to “ON” position and Flush Switch to “ICE” position,

water starts to be supplied to Reservoir.

17