ASSEMBLY
IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!
UNPACKING
LED DISPLAY WINDOWS
AUDIO-IN JACK
PULSE GRIPS
SUPPORT BAR
ON/OFF SWITCH
CIRCUIT BREAKER
TRANSPORT WHEEL
IPOD DOCKING STATION
HEADPHONE JACK
POWER CORD
HANDLEBAR
CONSOLE
MOTOR COVER
RUNNING BELT / RUNNING DECK
SIDE RAIL
ROLLER END CAP
CONSOLE MAST
REAR ROLLER
ADJUSTMENT BOLTS
SAFETY KEY PLACEMENT
WATER BOTTLE POCKET
TOOLS INCLUDED
PARTS INCLUDED
1 Console Assembly
(located under treadmill deck)
2 Console Masts
2 Handlebars
2 Support Bars
2 Water Bottle Pockets
6 Hardware Bags
Screwdriver
5 mm T-wrench
5 mm L-wrench
8 mm T-wrench
1 Safety Key
1 Bottle of Silicone Lubricant
3 iPod Dock Inserts
1 Universal MP3 Player Dock Insert
1 iPo d
Docking Station Rubber Plug
1 Audio Adaptor Cable
1 Power Cord
FOOT LOCK LATCH
WHEEL LOCK
During the assembly process of the treadmill there are several areas that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may
cause irritating noises. There should be no side-to-side play in the console masts or any forward and back play in the
console assembly or handlebars. If there is any play in these areas, the treadmill has not been properly assembled. To
prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take
CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have
been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock
latch secure. Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and
may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
1
2
2/15/09 10:18 AM
BOLT (A)
20 mm
Qty: 6
FLAT WASHER (B)
8 mm
Qty: 4
SPRING WASHER (C)
8 mm
Qty: 6
ARC WASHER (D)
8 mm
Qty: 2
Open HARDWARE BAG 1.
A
B
C
D
E
PRE-ASSEMBLY
MAIN FRAME BRACKET
LEFT CONSOLE MAST
BOLTS (A)
FLAT WASHERS (B)
ARC WASHERS (D)
SPRING WASHERS (C)
SPRING WASHERS (C)
BOLTS (A)
FLAT WASHERS (B)
SPRING WASHERS (C)
BOLTS (A)
ASSEMBLY STEP 1
HARDWARE BAG 1 CONTENTS:
ASSEMBLY STEP 2
RIGHT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
MAIN FRAME BRACKET
RIGHT CONSOLE MAST
BOLTS (A)
FLAT WASHERS (B)
ARC WASHERS (D)
SPRING WASHERS (C)
SPRING WASHERS (C)
BOLTS (A)
FLAT WASHERS (B)
SPRING WASHERS (C)
BOLTS (A)
CONSOLE CABLE
BOLT (A)
20 mm
Qty: 6
FLAT WASHER (B)
8 mm
Qty: 4
SPRING WASHER (C)
8 mm
Qty: 6
ARC WASHER (D)
8 mm
Qty: 2
HARDWARE BAG 2 CONTENTS:
A
B
C
D
E
F
Disassemble box and remove the cardboard packaging that is not beneath the treadmill. Do not attempt to lift the treadmill at
this time. Remove plastic wrap from console masts.
*NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely
tightening any ONE bolt. A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike
grease is recommended.
3
LEFT CONSOLE MAST
Slide
BRACKET.
Insert 2
2
FLAT WASHERS (B)
and
of the mast to secure the
MAINFRAMEBRACKET.
Insert 2
2
FLAT WASHERS (B)
the mast to secure the
MAINFRAMEBRACKET.
Insert 2
ARCWASHERS (D)
secure the
BRACKET.
NOTE:
screws or bolts until step 6 is complete!
into
MAIN FRAME
B OLTS (A), 2 SPRING WASHERS (C)
from the bottom outside
CONSOLEMAST
to the
BOLTS (A), 2 SPRING WASHERS (C)
from the bottom inside of
CONSOLEMAST
BOLTS (A), 2 SPRING WASHERS (C)
from the front of the mast to
CONSOLEMAST
to the
Do not completely tighten any
to the
and2
MAINFRAME-
and
Pull LEAD WIRE through
MAST.
RIGHT CONSOLE
After pulling the lead wire through the mast, the
top of the console cable should be located at the
top of the mast. Detach and discard lead wire.
Open HARDWARE BAG 2.
Slide RIGHT CONSOLE MAST into
FRAME BRACKET.
MAIN
NOTE: Do not pinch CONSOLE CABLE when
placing the mast onto the main frame.
Insert 2 BOLTS (A), 2 SPRING WASHERS (C)
and 2 FLAT WASHERS (B) from the bottom
outside of the mast to secure the CONSOLE
MAST to the MAIN FRAME BRACKET.
Insert 2 BOLTS (A), 2 SPRING WASHERS (C)
and 2 FLAT WASHERS (B) from the bottom
inside of the mast to secure the CONSOLE
MAST to the MAIN FRAME BRACKET.
Insert 2 BOLTS (A), 2 SPRING WASHERS (C)
and 2 ARC WASHERS (D) from the front of
the mast to secure the CONSOLE MAST to
the MAIN FRAMEBRACKET.
NOTE:
Do not completely tighten any
screws or bolts until step 6 is complete!
4
2/15/09 10:20 AM