Horizon Fitness CT5.1 User Manual

CT5.1

TREADMILL OWNER’S MANUAL

MANUEL D’UTILISATION DU TAPIS ROULANT

Read the TREADMILL GUIDE before using this OWNER’S MANUAL. Lire le GUIDE DU TAPIS ROULANT avant de se servir du présent MANUEL D’UTILISATION.

3 ENGLISH 21 FRANÇAIS

ASSEMBLY

WARNING

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your treadmill’s serial number located near the on/off power switch and power cord and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:

SERIAL NUMBER:

MODEL NAME: HORIZON CT5.1 TREADMILL

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service. » Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.

RE ADING RACK

TOU CH PAD PANEL AND DI SPLAY WINDO WS

SUPPO RT BAR

WATE R BOTT LE HOL DE R

GRIP P UL SE HANDRAILS

ON/OFF S WITCH

CIRCU IT BREAKER

POWER CO RD

TRANSPO RT WHEEL

SPEAKERS

CONSO LE

IPOD/MP3 P LAYER POCKET

SAF ET Y K EY PL ACEMENT

CONSO LE MAS T

FOOT LO CK LATCH ( UN DE RN EATH DECK)

MOTOR C OVER

SIDE RAIL

ROL LER END CAP

RUNNI NG BELT / RUNNIN G D ECK

RE AR ROL LER

ADJ US TMENT BO LTS

TOOLS INCLUDED:

F Screwdriver F 6 mm T-Wrench F 5 mm L-Wrench F 4 mm L-Wrench

PARTS INCLUDED:

F 1 Console Assembly F 2 Console Masts F 1 Support Bar F 2 Bottom Console Covers F 5 Hardware Bags F 1 Safety Key F 1 Audio Adapter Cable F 1 Bottle of Silicone Lubricant (for 2 applications)

PRE ASSEMBLY

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.

WARNING

DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. You may remove the plastic wrap from console masts.

WARNING

NEED HELP?

If you have questions or if

there are any missing parts,

contact Customer Tech

Support. Contact information

is located on the back panel

of this manual.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

NOTE: During assembly, do not completely tighten any screws or bolts until step 4 is complete!

NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.

ASSEMBLY STEP 1

LEFT CONSOLE MAST

HARDWARE BAG 1 CONTENTS :

BOLT (A) 20 mm Qty: 4

RUNNING DECK

FLAT WASHERS (C)

SPRING WASHERS (B)

BOLTS (A)

SPRING WASHER (B) 15 mm Qty: 4

FOOT LATCH

BASE FRAME

FLAT WASHER (C) 15 mm Qty: 4

A Cut the yellow banding straps and lift the

running deck upward until the foot latch locks. Remove all contents from

underneath the running deck.

B Open hardware bag 1.

C With the running deck in the raised

position, attach the left console mast to the base frame using 4 bolts (a), 4 spring washers (b) and 4 flat washers (c).

NOTE: Do not completely tighten any screws or bolts until

step 4 is complete!

ASSEMBLY STEP 2

RUNN ING DECK

HARDWARE BAG 2 CONTENTS :

BOLT (A) 20 mm Qty: 4

BASE FRAME

SPRING WASHER (B) 15 mm Qty: 4

FLAT WASHER (C) 15 mm Qty: 4

LEAD WIRE

CONSOLE CABLE

RIGHT CON SOLE MAST

BOLTS (A)

SPRIN G WASHER S (B)

FLAT WASHERS (C)

A Open hardware bag 2.

B Pull lead wire through right console

mast. After pulling the lead wire through the mast, the top of the console cable should be located at the top of the mast. Detach and discard the lead wire.

C With the running deck in the raised

position, attach the right console

mast to the base frame using 4 bolts (a), 4 spring washers (b) and 4 flat washers (c).

NOTE: Do not completely tighten any screws or bolts until

NOTE: Be careful not to pinch any wires while assembling the right console mast.

step 4 is complete!

ASSEMBLY STEP 3

ASSEMBLE

LEFT SIDE

FIRST

HARDWARE BAG 3 CONTENTS :

BOLT (D) 25 mm Qty: 2

CONSOLE

FLAT WASHER (E) 16 mm Qty: 2

CONSOLE CABLES

FLAT WASHER (E)

BOLT (D)

CONSOLE MAST

A Disengage the deck lock latch with your

foot to lower the running deck.

B Open hardware bag 3.

C Gently place the console on top of the

console masts. Attach the left side first using 1 bolt (d) and 1 flat washer (e).

D Connect the console cables, carefully

tucking wires in masts to avoid damage.

E Attach the right side of the console

using 1 bolt (d) and 1 flat washer (e).

NOTE: Do not completely tighten any screws or bolts until

NOTE: Be careful not to pinch any wires while assembling the masts.

step 4 is complete!

ASSEMBLY STEP 4

HARDWARE BAG 4 CONTENTS :

BOLT (H) 15 mm Qty: 4

A Open hardware bag 4.

B Align support bar with holes in console

masts.

C Insert bolts (h) into all 4 holes of the

support bar. Note: look into holes in the right mast before inserting bolts to avoid pinching cables.

D Tighten all bolts completely.

CONSOLE

BOLTS (H)

SUPPORT BAR

CONSOLE MAST

ASSEMBLY STEP 5

HARDWARE BAG 5 CONTENTS :

SCREW (G) 15 mm Qty: 4

CONSOLE

BOTTOM CONSOLE COVER

SCREWS (G)

CONSOLE MAST

A Open hardware bag 5.

B Slide right bottom console cover up

console mast and align screw holes. Attach bottom console cover to console

using 2 screws (g).

C Repeat on other side.

D Connect power plug to a power outlet. The ON/

OFF switch is located next to the power cord. Flip this switch to the ‘ON’ position, so that the switch is lit. You will hear a beep and the console will turn on.

E Before the first use, lubricate the treadmill

deck by following the instructions in the MAINTENANCE section in the TREADMILL GUIDE.

YOU ARE FINISHED!

TREADMILL OPERATION

This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the TREADMILL GUIDE has instructions for the following:

• LOCATION OF THE TREADMILL

• USING THE SAFETY KEY

• FOLDING THE TREADMILL

• MOVING THE TREADMILL

• LEVELING THE TREADMILL

• TENSIONING THE RUNNING BELT

• CENTERING THE RUNNING BELT

• USING THE HEART RATE FUNCTION

TIME DISTANCE

CALORIES

INCLINE

MANUAL

WEIGHT

INTERVALS

LOSS

% COMPLETE

SCAN

ROLLING

HILLS

HEART RATE

SPEED

SAVED

WEIGHT

MANUAL

INTERVALS

HILLS

ROLLING

LOSS

U U

™

P P

My K E Y S

Press and hold a MyKEY for three seconds to set

key to current incline.

™

LOW HIGHMED

SLOW MED

™

My K E Y S

™

Press and hold a MyKEY for three seconds to set

FAST

key to current speed.

T T

F J SL KHM G I

SPE EDINC LIN E

+ 28 hidden pages