Hopkins CWL623HCO User Manual

CWL623 • BLAZER LINK™ • OWNER’S MANUAL

FCC ID: TJJCWL623HCO
IC: 6047A-CWL623HCO
Model Name:CWL623HCO

Overview

This is a professional wire management system that is linked to your smartphone. The Blazer Link™
is designed for operating accessories (including lights, horns, warning beacons, etc.) typically used on
work or off-road vehicles (trucks, jeeps, ATV/UTV, boats, heavy equipment, farm equipment, etc.).
The unit works on 12V DC and provides output to four terminals which are protected by a 40A fuse.

Please note that before you can operate this system, you need to download and install the Blazer
Link™ App on your smartphone from the App store.

Main Unit

1.

Please read these instructions carefully before installing this produc t. It is recommended to
consult a professional installer to prevent damage to vehicle and/or system.

2.

Do not connect to 24V DC or higher voltage system, as this product is designed for a 12V DC
battery system. In case you have a larger than 12V DC system, check vehicle owner’s manual to
determine if a 12V DC output is available and how to connect in order to use it safely, otherwise,
the product will be damaged.

3.

Find a suitable flat surface near the battery, clean the surface free of dirt and oil and then affix the
unit using provided adhesive strips and/or mounting holes.

4.

Remove the 40A fuse from the holder and disconnect the vehicle battery.

5.

Securely attach the positive (red) cable of the Blazer Link™ unit to the positive terminal of the
battery or battery cable and the negative (black) cable of the Blazer Link™ to the negative battery
cable or chassis.

6.

Terminal 2A has additional light control functions like adjusting brightness and strobe rate, and
should not be used for connecting warning/strobe lights or horns.

7.

Attach the auxiliary lights/equipment following correct polarity on the terminals and not exceeding
the maximum amperage of the channels (amperage printed on Blaz er Link™ and corresponds to
amperage on your smartphone App for each terminal). See FIG 1 (on page 3)

8.

Reconnect battery cables.

9.

Insert the 40A fuse back into the holder and snap the cover close.

App Instructions

1.

Download and install the Blazer Link™ App for your smartphone operating system available on
App Stores.

2.

For initial setup, tap the “radio” icon to go to the “connect” screen. Simply select the module
and enter the appropriate numerical password (default is 123456).

3.

Once connected, hit the back button on top right hand screen, to return to the main screen.

4.

Now, select your vehicle type by tapping on the arrow to the right of the initial schematic.

5.

Next, select light location setup to assign lights to different locations on your vehicle. Tap on
the terminal and then tap on the desired location. Repeat this for the remaining terminals and
then hit enter to return to the main screen.

6.

You are now set up to operate your lights.
Activate the system by tapping the power icon . It will turn green to indicate that it is

7.
powered on .

8.

Now, select a light. The light icon will turn blue to indicate it is the active selection.

BLAZER-INTERNATIONAL.COM

1-800-835-0129

Patent Pending
© Copyright 2018

Page 1 of 10

CWL623 • BLAZER LINK™• OWNER'S MANUAL

9.

You can turn on and off the light via the “individual Terminal ON/OFF” switch.

Note: Terminals marked are used in conjunction with a warning light with different strobe

patterns built into it.

Most warning lights with strobe function come with three wires, black, red and yellow. Black
is to be connected to negative terminal, red to positive terminal and yellow is for advancing
the strobe patterns. Consult with the manufacturer of the light to determine if yellow is on the

negative side of the circuit or on the positive side and

terminal.

Terminal 2A has been specifically designated for additional light controls. With
applicable lights, you may use the respective sliders to adjust both brightness and
strobe rate.

10.

Once the lights have been set up as desired, the whole system can be turned on and off by the
master power button . When this master power icon is grayed out, all the lights will be off.

Additional features can be found in the settings screen , indicated by the gear icon.

11.

b.

Low voltage alert - If the Blazer Link™ detects that your battery level is lower than the
set voltage, it will notify you via the alert.

c.

Timer - allows you to set time period when you want your lights to
automatically turn off to prevent unnecessary battery draining.

d.

You can also rename your device and set a new password.

12.

Back on the main screen, select the battery icon to view readout of your battery level and voltage
standing. Additionally, this is the icon that will turn red and notify you when your battery level has
reached the low voltage level you defined earlier in the settings tab. It is also possible to pick one
of the five audible sounds or vibrator, which will alert you.

13.

Once set up, try to manipulate each light to ensure that the system is working properly.

connect it to the appropriate polarity of

Specifications

Standard design 12V, max 40A
Rated input voltage DC 13V
Working voltage DC 11-15V
Working temper ature
Fuse 40A
Low-voltage protection circuit
Thermal shut off temperature

9.8V +/- 0.3V DC. with 8 sec delay

0°F - 225°F / -17°C - 107°C

248°F / 120°C

BLAZER-INTERNATIONAL.COM

1-800-835-0129

Page 2 of 10

Patent Pending
© Copyright 2018