Fillin and retain!
1111"I"I" I " . I
,TheHOOVER vacuum cleaner you have just purchased is a combina-
tuO_cleaner. It Is used for carpet and rug cleannng and may be used
with attachments for above the floor cleaning.
The model and serial number appear toward the rear of the bottom of
the cleaner.
For your personal records, please enter these numbers in the spaces
provided below and retain in a safe place.
Your cleaner is model
and has serial number
Save!
Index
Assembling Cleaner. • ........................... 5
Cleaner Description ........................... 3,4
How to Use
Cleaning Tools ............................. 8-11
Special Features .............................. 7
Upright Cleaner ............................. 6-7
If You Havea Problem .......................... 21
Important Safeguards ........................... 2
Lubrication ................................. ..2 1
Maintenance
Authorized Hoover Service ................. 12,21
Dirt Duct and Dirt Tube .................... 18,19
Replacing Belts ........................... 15-17
Replacing Brushes ........................... 20
Replacing Headlight ......................... 14
Replacing ThrowAway Bag ................ 12,13
© 1978 The Hoover Company
Important Safeguards!
• Read all instructions.
* Warning: Electric shock could occur if used outdoors or on wet
surfaces.
• Close supervision is necessary when any appliance is used by or
near children. Do not allow vacuum cleaner to be used as a toy or to
run unattended at any time.
• Keep hands, feet, loose clothing, and hair away from rotating agita-
tor. Do not operate cleaner in bare feet or when wearing open toe
shoes or sandals.
• Don't run cleaner over cord. It may damage insulation.
• Do not use cleaner to pick up matches, or live ashes and cigarette
butts.
• Never vacuum in the presence of flammable or combustible liquids
or fumes.
• Avoid picking up hard, sharp objects with the cleaner. They may
damage the cleaner and the bag.
• Do not allow cleaner to run in a stationary position on non-carpeted
floors; damage could occur to these surfaces.
• Unplug cleaner when not in use. Turn machine off at switch before
unplugging.
• Always disconnect cord from electrical outlet before servicing the
cleaner.
• Change bag frequently when picking up very fine materials such as
powder.
• Grasp the plug to disconnect from wall outlet to avoid damage to
cord, plug, prongs, or receptacle.
• If cleaner has a cord reel, hold on to the plug while cord is being re-
wound to prevent cord from whipping.
• The use of an extension cord is not recommended.
• If cleaner is in disrepair, do not attempt to operate.
• Have repairs made by the qualified personnel at Hoover Factory
Service Centers or Authorized Hoover Warranty Service Dealers.
• Use vacuum cleaner only for its intended use as described in the
instructions. Use only attachments recommended by the appliance
manufacturer; others may cause hazards.
Save these instructions!
Quahty
Products
thru
Employee
Pa rt_c0p,_t_on
Unpacking
section
Cleaner base
and bag
assembly
Unpack the cleaner from the car-
ton and remove and dispose of
cardboard packing.
7
6
Cord reel model
Make a small loop with cord and
place it over the hook at the back
of the handle. When operating,
cord should be positioned as
shown.
1
11
Before operating your cleaner,
identify features and controls
shown in the diagram, then,
read the section on "How to use."
1. Edge Cleaning: Brushed edge cleaning is provided on the right side
of the cleaner. Standard edge cleaning is provided on the left side.
2, Handle Release Pedals; step on either pedal to lower handle to either
operating or low position. (Some models have only one pedal.)
3. Cord Reel: to unwind cord, pull from cord reel to desired length,
(Available with some models.)
4. Cord Return Button: depress to automatically rewind cord for
storage. Hold plug until cord is rewound. (Available with some
models.)
5. Vinyl Bag Jacket: covering for throw away bag.
6. Bag Spring: place spring ring over hook to support the bag.
7. ON-OFF Switch: some models have two speeds.
8. Handle Grip
9. Twin Headlight (Available with some models.)
10. Carpet Height Adjustment Lever: choose "'LOW/MED", "PLUSH",
or "SHAG".
11. Molded Furniture Guard
Note: If using cleaner on new carpet, be sure to change bag frequently.
See "Maintenance" section for bag replacement.
Operate cleaner only at voltage specified on data plate on bottom of
cleaner.
Cord wrap model
Wrap cord around hooks for stor-
Cord
storage
hooks
age.
On some models the top hook can
be rotated forward or backward
for easy cord release. The hook
can then be repositioned for
wrapping the cord.
How to assemble
Remove the tape holding the two
handle attachment screws from
the lower end of the handle. Set
screws aside.
Align handle with ON-OFF switch
to the rear of the cleaner and label
to the front. Fold cord beside cord
tube as shown. Push cord and
tube completely up into handle.
CORD
Insert handle into the cleaner to
the line indicated on label. Inser-
tion to the line is necessary for
proper screw alignment.
Remove paper bag from inside the
vinyl jacket. Then remove dirt tube
by pushing to either side to release
retention clips. Lift tube up and
out.
Lower handle to operating posi-
tion and place spring bag ring over
hook located on handle.
Insert the two screws into the
holes provided inside the front
housing.
Tighten with screwdriver. Snap
dirt duct back into place. Replace
paper bag. (Follow instructions
on bag.)
Zip vinyl jacket. Cleaner is ready
to use.
UPRIGI,tr
How to use
To transport
To move your cleaner from room
to room, put the handle in the ,p-
right position, tilt the cleaner back
on the large rear wheels and push
forward.
Handle adjustment
The handle of your cleaner has
three positions: Upright for stor-
age and when using attachments.
Operating for general operation on
carpet and foors. Low for reaching
under low furniture. The handle
can be lowered by stepping on the
pedal on either side at the rear of
the cleaner. (Some models have
only one pedal. )
ON-OFF switch
OFF
LOW
HIGH
To turn cleaner ON, push switch
down. To turn cleaner OFF, push
switch up.
Some cleaners are equipped with
a two-speed switch. When the
switch is pushed up as far as pos-
sible, it is in the OFF position.
LOW SPEED is to be used for less
vigorous cleaning and reduced
suction on delicate carpet, rugs,
and non-carpeted floors. Slide
the switch down one notch from
OFF to LOW speed.
HIGH SPEED is to be used for
cleaning most carpet and for use
with attachments. When the
switch is pushed down as far as
possible it is in HIGH speed.
Note: When cleaning any floor
covering, turn cleaner "OFF"
when unattended, particularly on
non-carpeted floors. The agitator
cleans so thoroughly that opera-
tion while the cleaner is stationary
may mar the floor covering.
Special features
Edge cleaning
Brushed edge cleaning is provided
on the right side of the cleaner to
remove imbedded dirt in carpet
near baseboards and furniture.
Guide the right side of the cleaner
parallel to the edge of carpet or
furniture for brushed edge clean-
ing.
Standard edge cleaning is provid-
ed on the left side of the cleaner.
Standard edge cleaning removes
surface dust and litter.
Adjustment for carpet
pile height
The cleaning of carpet and rugs
takes place at the nozzle. This is
the opening at the bottom of the
cleaner where the agitator is lo-
cated.
It is necessary for the nozzle to be
adjusted properly to the various
carpet pile heights. The adjust-
ment lever on the front of the
cleaner may be set on three differ-
ent self-adjusting ranges.
On very dense pile plush or shag
carpet, some difficulty in pushing
the cleaner may occur. In this
case, position the adjustment le-
ver on PLUSH or SHAG.
When cleaning non-carpeted
floors, set adjustment lever to
LOW/MEDIUM and use LOW
SPEED, if available on your
cleaner. Because of the vigorous
action of the agitator, do not
allow cleaner to run in a sta-
tionary position on any floor
covering, as marring may occur.
Disconnect cleaner from electri-
cal outlet before making nozzle
adjustment.
To change nozzle adjustment
grasp the handle and tilt the
cleaner forward. Move the lever
with your hand until it "clicks" in-
to the desired position.