Hoover U4343, U4341, U4335, U4325, U4315 Owner’s Manual

...
H
0
0 V
R
nvertible
The HOOVER vacuum cleaner you have just purchased is a com tion cleaner. It is used for carpet and rug cleaning and may be
with attachments for above the floor cleaning. Your cleaner isa model
and has a serial number
For your personal records, please enter the model number and serial number in the spaces provided above and retain in a safe place.
The model number and serial
number appear on the bottom of the cleaner base.
" I
CLEANER BASE
Save!
Index
Cleaner Description and Unpacking ............. 3,4
Energy Saving Tips ............................ 20
How to Assemble Cleaner ...................... 5-7
How to Use on Carpet and Roore ............... 7-9
How to Use Cleaning Tools ................. ,. 10-13
If You Have a Problem .......................... 19
Important Safeguards ........................... 2
Lubrication ................................... 20
Maintenance
Authorized Service .......................... i9
How to Replace Belt ...................... 16,17
How to Replace Brushes ................... 17,18
How to Replace Headlight .................... 15
How to Replace Throw Away Bag ....... 6,7,14,15
Second Speed ................................. 13
Special Features ................................ 9
© 1972, 1982 The Hoover Compan!
Important Safeguards!
_r d all instructions.
ning: Electric shock could occur if used outdoors or on wet
surfaces.
Close supervision is necessary when any appliance is used by or near children, Do not allow vacuum cleaner to be used as a toy or to
run unattended at any time,
Keep hands, feet, loose clothing, and hair away from rotating
agitator. Do not operate cleaner in bare feet or when wearing open
toe shoes or sandals.
Don't run cleaner over cord. It may damage insulation.
Do not use cleaner to pick up matches, or live ashes and cigarette
butts.
Avoid picking up hard, sharp objects with the cleaner. They may
damage the cleaner and the bag.
Unplug cleaner when not in use. Turn machine off at switch before
unplugging,
Always disconnect cord from electrical outlet before servicing the cleaner.
Change bag frequently when picking up very fine materials such as powder.
Grasp the plug to disconnect from wall outlet to avoid damage to
cord, plug, prongs, or receptacle.
The use of an extension cord is not recommended.
If cleaner is in disrepair, do not attempt to operate.
Have repairs made by the qualified personnel at Hoover Factory Service Centers or Authorized Hoover Warranty Service Dealers.
se vacuum cleaner only for its intended use as described in the
structions. The use of attachments not recommended by the
appliance manufacturer may cause hazards.
Save these instructions!
Unpacking
E
_Unpack the cleaner from the _icp.rton and identify the parts
shown. Remove and dispose of the cardboard packing,
A. Upper handle section
B, Lower handle section
C, Cleaner main body and hood assembly
D- Outer bag assembly
E. Throw away bag
The cleaner assembled will look
like the drawing below.
5
IB
6
7
C D
1
8
9
3
11
2
12
3 After identifying each part, begin assembling.
I_adlight (available with some models).
!. Hood
3. Adjustment Lever for Carpet Pile Height: to adjust the underside of the cleaner (nozzle location) to the carpet pile height.
1. Cord Storage Hooks: wrap cord around hooks for storage. On some models, the top cord storage hook can be rotated forward or
backward for easy cord release.
i. Handle
i. ON-OFF Switch: to turn on, push switch downward; to turn cleaner
off, push switch upward.
t, Spring Hook: place spring ring over hook to support the bag.
i. Outer Bag: covering for throw away bag. !. Handle Bail: support for handle.
1.Carrying Handle: located on the underside of the handle bail.
I. Handle Release Lever: step on lever to lower handle to Operating
and Low position.
!. Furniture Guard: prevents cleaner from marking furniture.
tre cleaner only at voltage specified on data plate on bottom of
base.
4
How to assemble
A. Put handle together
Remove cardboard from the end
of handle sections.
Slide the two handle sections to- gether. Check to see that cord storage hooks are on the same
side of handle. Insert bolt through small holes and secure with nut.
Tighten nut with screwdriver.
If the nut and bolt will not assem-
ble as shown in the illustration,
the holes in the handle are not
lined up correctly.
B. Attach handleto
the cleaner
Unscrew nut and remove bolt
and plate from handle bail.
Take assembled handle and place
so that the socket holes in the bottom of the handle are directly
in line with the electrical prongs.
Position the handle so that the ON-OFF switch is to the rear of the cleaner.
Push down until handle is secure-
ly in place. Insert bolt into small
hole in front of handle.
Replace plate on back of handle,
by inserting projection on plate into lower hole on handle. Tabs
on handle bail will fit into notches on plate. Position nut on bolt and
tighten with screwdriver.
BAG
CLIP
C, Attach outer bag
to cleaner
The outer bag is connected at the
rear of the cleaner by hooking the two projections at the bottom of the outer bag assembly into the grooved plate extending from
back of cleaner base.
Then pull the bag clip (located
just above the cleaner opening)
to the left and fit bag against opening. Slide the bag clip to the
right to fit completely over the bag lock.
\
Attach the bag to the spring
hook, located on the top section
of the handle.
D. Attach throw away bag to cleaner
Use HOOVER bag type C with this cleaner. Unzip the outer jack-
et and pull out tube. Roll rubber
bag retainer down the tube toward the cleaner.
Slip the open end of the throw
away bag onto tube and push as far on as possible. (Be sure to
match arrow on throw away bag
with the 0 mark on the tube.)
Loading...
+ 15 hidden pages