Hand Vac
Owner’s Manual
English ➜ pp. 1-7
Español ➜ pág. 8-11
Français ➜ p. 12-16
Review this manual before
operating cleaner.
www.hoover.com
®
TM
Thank you for selecting a HOOVER product.
This cleaner was inspected and packaged carefully before being
shipped from the factory. If you should happen to need assistance
during assembly or operation,
Visit us online at www.hoover.com to find the service outlet
nearest you (click on the “Service” button) or
Call 1-800-944-9200 for automated referral of authorized
service outlet locations (U.S. only) or
Call 1-330-499-9499 to speak with a representative in our
Consumer Response Center.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
2
Fill in and retain
The HOOVER vacuum cleaner you have just purchased is a lightweight handheld cleaner. It is designed for quick cleanups on carpet, rugs or upholstery.
The model and serial number are located on the bottom of the cleaner.
For your personal records, please enter the COMPLETE model and serial number
in the spaces provided and retain this information.
Your cleaner is model
and has serial number
It is suggested that you attach your sales receipt to this owner’s manual.
Verification of date of purchase may be required for warranty service of your
Hoover product.
Save!
Index
Cleaner Descriptions .........................3
How to Use ......................................3-4
If You Have a Problem .......................7
Important Safeguards ........................2
Lubrication ..........................................7
Maintenance
Agitator Belt ................................5-6
Agitator Brush ............................6-7
Clearing Blockages .......................5
Dirt Cup .......................................4-5
Reusable Filter ...............................5
© 2003 The Hoover Company
www.hoover.com
Important Safeguards!
When using an electrical appliance, always follow
basic precautions, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
Warning:
• Do not use outdoors or on wet surfaces.
• Close supervision is necessary when any appliance is used by or near
children. Do not allow vacuum cleaner to be used as a toy or to run unattended
at any time.
• Keep hair, loose clothing, fingers, feet and all parts of body away from openings, rotating agitator and other moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes.
• Do not use to pick up flammable or combustible liquids such as gasoline or
fine wood sandings or use in areas where they may be present.
• Avoid picking up hard, sharp objects with the cleaner. They may damage the
cleaner and the bag.
• Do not use without dirt cup in place. When picking up very fine materials such
as powder, empty dirt cup often.
• Use extra care when cleaning on stairs.
• Do not put any object into openings. Do not use with any opening blocked;
keep free of dust, lint, hair, or anything that may reduce air flow.
• Do not pull or carry by cord, use cord as a handle, close door on
cord or pull cord around sharp edges or corners. Do not run appliance over
cord. Keep cord away from heated surfaces.
• Always disconnect cord from electrical outlet before servicing the cleaner.
• Unplug cleaner when not in use. Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Never handle plug or appliance with wet hands.
• The use of an extension cord is not recommended.
• Do not use with damaged cord or plug. If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, take it to a
Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer
(Depot).
• Use vacuum cleaner only for its intended use as described in the instructions.
Use only attachments recommended by The Hoover Company; others may
cause hazards.
Save these instructions!
To reduce the risk of fire, electric shock, or injury:
3
Unpack the cleaner from the carton and
identify the parts shown. Remove and
dispose of cardboard packing.
1. Bottom plate
2. Multi-purpose nozzle
3. Front cover
4. On/Off switch
5. Handle
6. Dirt cup
7. Dirt cup latch button
8. Nozzle latch
This cleaner is intended for household
use.
Operate cleaner only at voltage speci-
fied on data plate on bottom of cleaner.
1. Cleaner Descriptions
1-1
Questions or Concerns?
The Hoover Company wants to quickly resolve any concerns about your cleaner or
questions regarding its use. Look on the list provided with the product for your local
Hoover Factory Service Center or in the Yellow Pages under “Vacuum Cleaners –
Household” for the nearest Authorized Hoover Warranty Service Dealer (depot) or:
Visit us online at www.hoover.com to find the service outlet nearest you
(click on the “Service” button or call:
1-800-944-9200 for an automated referral of authorized service
outlet locations (U.S. only) or call:
1-330-499-9499 to speak with a representative in the Hoover
Consumer Response Center.
1
2
3
4
5
6
7
8
ON
OFF
2-1
2-2
ON/OFF switch
To reduce of risk of electric shock, this
appliance has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit,
contact a qualified electrician to install
the proper outlet. Do not change the
plug in any way.
Plug cord into electrical outlet. Slide
ON/OFF switch back to turn cleaner off.
2. How to Use
Multi-purpose nozzle
The multi-purpose nozzle has been built
into the front of the cleaner. It is
designed for use on carpet, rugs, upholstered furniture, mattresses, automobile
interiors and carpeted stairs.
The nozzle has a rotating agitator
which should be kept away from hair,
hands, feet and loose clothing. Keep
cleaner away from children.
2-3
How to rotate nozzle
CAUTION: MOVING PARTS. TURN
CLEANER OFF BEFORE ROTATING
NOZZLE.
To rotate nozzle either vertically or horizontally, place thumb on latch (A) with
finger on front of nozzle.
Press latch toward edge of nozzle and
rotate.
A
Continued
➜
4
Brushed edge cleaning
Brushed edge cleaning is provided on
both sides of the nozzle to remove dust
and lint along edges of baseboards and
furniture. Guide either side of the nozzle
along edge as shown.
2-4
3. Maintenance
Maintenance
Familiarize yourself with the home maintenance tasks presented in the following
sections. Keep this owner’s manual in a
convenient place where you can refer to
it when needed. Proper use and care of
your cleaner will ensure continued
cleaning effectiveness.
3-1
The dirt cup
The debris picked up by the cleaner is
deposited into the dirt cup. Empty after
each use. Before reattaching, the cup
may be cleaned with a damp cloth or
rinsed with water if necessary. Dry the
cup thoroughly before reusing.
How to empty
Disconnect cleaner from electrical
outlet.
Hold cleaner in a vertical position as
shown.
3-2
A
Grasp dirt cup section; depress dirt cup
latch (A).
3-3
Slide dirt cup off handle section.
3-4
With dirt cup section in hand, grasp
extension on filter frame and lift out.
3-5
Empty dirt cup.
3-6
Pull middle section of filter out of filter
frame.
Brush surface of filter to remove any
clinging litter.
Push filter back into frame.
5
3-7
3-8
Replace filter, matching rounded flap
with rounded side of dirt cup (opposite
side that slides onto handle).
3-9
9. Slide dirt cup completely onto handle
making sure latch is secure.
Clearing blockages
Removing larger items from carpet and
other surfaces before vacuuming will
help prevent obstructions in the nozzle
or dirt passageway, and maintain the
cleaning effectiveness of your cleaner.
3-10
To check for obstructions, first turn
cleaner Off and disconnect cord from
electrical outlet. Remove dirt cup;
remove any obstruction from dirt passageway. The bottom plate may be
removed if there is an obstruction in the
nozzle. See “The Belt” section.
3-11
Reusable filter
How to clean
Disconnect cleaner from electrical
outlet.
The filter protects the motor from dirt
particles. Brush dirt from filter when
emptying dirt cup. If a significant reduction in pick up is observed, the filter may
be washed in warm water. Filter must
be completely dry before replacing it in
cleaner. Do not use cleaner without filter
in place. Avoid picking up oily debris
that may damage filter.
3-12
The belt
The belt in your cleaner drives the agitator. It has been designed specifically for
use in this cleaner and is important for
effective operation.
What to buy
When purchasing a new belt, ask for
Hoover part No. 38528032.
How to replace
Disconnect cleaner from electrical
outlet.
The belt is located behind the front
cover of your cleaner and should be
checked from time to time. Replace the
belt if it is stretched or broken.
To check belt, rotate nozzle to vertical
position.
Lift off front cover (B).
B
3-13
Remove the two bottom plate screws.
Continued
➜
6
3-14
3-15
3-16
3-17
3-18
3-19
3-20
Pivot off bottom plate making sure to
unhook center tab on inside edge of
nozzle (opposite edge with screws).
If belt (C) is stretched, remove it from the
motor pulley.
Remove agitator and belt from nozzle.
C
Put new belt on agitator.
Position agitator in nozzle orienting agitator end caps with slots on both sides
of nozzle. End cap with side projections
(Fig. 3-17, D) fits into slot opposite the
end with nozzle latch (Fig. 3-17, E).
The agitator end caps may fall off during
belt replacement. For correct orientation
of end caps onto agitator, see “How to
replace Agitator Brush.”
The belt should line up with tab (F) on
inside of nozzle.
F
E
D
G
Attach belt to motor pulley.
Replace bottom plate by first hooking it
to center tab on inside of nozzle.
Reposition screws and front cover.
Make sure “bridge” (G) across bottom
plate opening covers belt. If belt is not
covered, agitator is not correctly oriented in nozzle.
Agitator brush
Disconnect cleaner from electrical
outlet.
To check condition of agitator brushes,
move the edge of a card across agitator
opening. Rotate agitator by hand. If
brushes do not touch edge of card,
replace the agitator.
What to buy
When replacing the agitator, ask for
HOOVER agitator complete with end
caps, part No. 59139205.
How to replace
Disconnect cleaner from electrical
outlet.
Remove bottom plate, agitator and belt
following directions for “How to replace
belt.”
Discard old agitator and end caps.
3-20
7
3-21
1 = End cap without side projections
2 = Fiber washer
2
2
1
3
4
5
3 = Agitator crown for belt
4 = Large end
5 = End cap with side projections
If the end caps should fall off the agitator, they are different from each other
and need to be properly oriented as
shown. End caps should fit tightly on
agitator.
Problem: Cleaner won’t run
Problem: Cleaner won’t pick up
Problem: Dirt falling from cleaner
Possible cause
Possible solution
• Not firmly plugged in.
•
Plug in firmly.
• No voltage in wall plug.
•
Check fuse or breaker.
• Blown fuse/tripped breaker.
•
Replace fuse/reset breaker.
Possible cause
Possible solution
• Dirt cup full.
•
Empty dirt cup.
• Nozzle, dirt passageway clogged.
•
Remove obstruction.
• Filter clogged.
•
Empty dirt cup and clean filter.
• Agitator brushes worn.
•
Repalce agitator.
• Broken or worn belt.
•
Replace belt.
Possible cause
Possible solution
• Flap on filter clogged or damaged.
•
Remove obstruction; replace filter
if necessary
If a minor problem develops, it usually
can be solved quite easily when the
cause is identified by using the check
list below.
4. If you have a
problem
Lubrication
The motor and agitator bearings are permanently lubricated. The addition of
lubricant could cause damage.
Therefore, do not lubricate the
cleaner.
Service
To obtain approved HOOVER service
and genuine HOOVER parts, locate the
nearest Hoover Factory Service Center
or Authorized Hoover Warranty
Service dealer (depot) by:
• checking the Yellow Pages under
“Vacuum Cleaners – Household”
OR–
• checking the list of Factory Service
Centers provided with this cleaner
OR–
• checking the Service section of
The Hoover Company on-line at
www.hoover.com
OR–
• calling 1-800-944-9200 for an automated referral of authorized service
outlet locations (U.S. only).
Do not send your cleaner to the Hoover
Company in North Canton for service,
this will only result in a delay.
If further assistance is needed, contact
The Hoover Company Consumer
Response Center, North Canton, Ohio
44720, Phone: 330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8,
Phone: 1-800-263-6376.
Always identify your cleaner by the com-
plete model number when requesting
information or ordering parts. (The
model number appears on the bottom of
the cleaner.)
Position agitator in nozzle and replace
bottom plate, screws and front cover following directions for “How to replace
belt.”
Loading...