Hoover POWER PATH PRO, Power Path Pro XL, Power Path Pro Advanced User Manual

IMPORTANT: Read carefully before assembly and use.

©2014 Techtronic Floor Ca re Technol ogy Limited. All Rights Reserved. Distribute d by, Royal App lianc e Mfg. Co. Glenwillow, Oh 44139 #961151133 ID110047-R0

User manual.

POWER PATH

™

PRO

CARPET WASHER

Welcome to

Hoover ownership.

Get cleaning confidence for up to 2 full years
with the Hoover

®

limited warranty.

Safety Instructions

How to assemble your Power Path

™

Pro

Getting started with your Power Path

™

Pro

Using your Power Path

™

Pro

How to attach your Power Path

™

Pro tools

Keeping your Power Path

™

Pro running properly

Troubleshooting

Warranty

1

3

5

7

11

17

25

26

Your Guide:

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

When using an electrical appliance, basic precautions should always be
followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY.
IF USED COMMERCIALLY WARRANTY IS VOID.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, DAMAGE OR INJURY:

•Fully assemble before operating.

•Operate cleaner only at voltage specied on data plate on lower back of
cleaner.

•Do not leave appliance when plugged in. Unplug from outlet when not in
use and before cleaning or servicing.

•Use indoors only.

•Do not immerse. Use only on carpet moistened by cleaning process.

•Use only HOOVER

®

cleaning products intended for use with this machine.

•Do not allow to be used as a toy. Not intended for use by children age
12 and under. Close supervision is necessar y when used near children.
To avoid injury or damage, keep children away from product, and do not
allow children to place nger s or other objects into any openings.

•Use only as described in this manual. Use only manufacturer’s
recommended attachments and products.

•Do not use with damaged cord or plug. If appliance is not working as
it should, has been dropped, damaged, lef t outdoors, or dropped into
water, take it to a service center prior to continuing use.

•Do not pull or carry by cord, use cord as a handle, close a door on
cord, or pull cord around sharp edges or corners. Do not place product
on cord. Do not run appliance over cord. Keep cord away from heated
surfaces.

•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

•Do not handle plug or appliance with wet hands.

•Do not put any object into openings. Do not use with any opening
blocked; keep free of dust, lint, hair, and any thing that may reduce air
ow.

•Keep hair, loose clothing, ngers, and all parts of body away from
openings and moving parts.

•Turn o all controls before unplugging.

•Use extra care when cleaning on stairs. To avoid personal injury or
damage, and to prevent the cleaner from falling, always place cleaner at
bottom of stairs or on oor. Do not place cleaner on stairs or furniture, as
it may result in injury or damage.

•Do not use to pick up ammable or combustible liquids, such as gasoline,
or ne wood sandings, or use in areas where they may be present.

•Connect to a properly grounded outlet only. See Grounding Instructions.

•Unplug before connecting SpinScrub powered hand tool.

•Do not pick up any thing that is burning or smoking, such as cigarettes,
matches, or hot ashes.

•Do not use without lters and tanks in place.

•Do not clean over oor electrical outlets.

1

2

21

A

B

C

WARNING: This product contains chemicals known

to the State of California to cause cancer, birth defects or

reproductive harm. WASH HANDS A FTER HANDLING .

GROUNDING INSTRUCTIONS:

This appliance must be grounded. If it should malfunction or breakdown,

grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This appliance is equipped with a cord having
an equipment-grounding conductor (C) and grounding plug (A). The plug
must be inser ted into an appropriate outlet (B) that is properly installed and
grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-grounding

conductor can result in the risk of electric shock. Check with a qualied
electrician or service person if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with the appliance - if it
will not t the outlet, have a proper outlet installed by a qualied electrician.
This appliance is for use on a nominal 120-volt circuit and has a grounding
plug that looks like the plug (A) illustrated in Fig. 1. A temporary adapter (D)
may be used to connect this plug to a 2-pole receptacle (E ) if a properly
grounded outlet is not available (Fig. 2). The temporary adapter should be
used only until a properly grounded outlet (B) can be installed by a qualied
electrician (Fig. 1). The green colored rigid ear, lug, or the like (F) extending
from the adapter must be connected to a permanent ground (G) such as a
properly grounded outlet box cover (Fig. 2). Whenever the adapter is used,
it must be held in place by a metal screw. NOTE: In Canada, the use of a
temporary adapter is not permitted by the Canadian Electrical Code.

D

E

F

G

D

CAUTION: TO REDUCE THE RISK OF DAMAGE:

•Avoid picking up hard, sharp objects with this product, as they may
cause damage.

•Store appropriately indoors in a dry place. Do not expose machine to
freezing temperatures.

•Do not use sharp objects to clean out hose as they can cause damage.

•To assist in reducing drying time, be certain the area is well ventilated
when using detergents and other cleaner s with this machine.

•To help prevent mat ting and resoiling, avoid contact with carpets until
they are dry. Keep children and pets away from carpets until they are
completely dr y.

•Do not store extractor with solution in tanks.

•With brushes and brushroll on, do not allow cleaner to sit in one location
for an extended period of time, as damage to the oor can result.

•Do not use this ex tractor on hard oors. Using this machine on hard
oors may scratch or damage your oor.

•Water will drip from the brushes and underside of the product after use
and may puddle. To avoid damage to wood and laminate ooring and
to avoid potential slip hazard, after use (a) do not leave the product on
wood and laminate surfaces and remove to a hard surface and (b) place
unit on absorbent material (such as a towel) to soak up drips.

3

1 2 3

Insert the handle into
the base.

Turn the dial clockwise to

the “LOCK” position.

Tip the Clean Water Tank

in like this on the handle

above the dirty water

tank. It’ll click.

How to assemble your Power Path™ Pro:

4

Before you begin cleaning:

Vacuum carpet and
upholstery thoroughly with a
Hoover® vacuum before use.

Don’t use the carpet cleaner
as a dry vacuum cleaner.

Use your Hoover

®

carpet
washer only if upholstery
fabric is marked with a “W”
(for “wet” clean) or “S/W” (for

“solvent/dry” or “wet” clean).

Don’t clean fabric marked “S”
(“solvent/dry” clean only).

Test for colorfastness in a
small, hidden area. Gently
rub surface with a dampened
white cloth. Wait ten minutes
and check for color removal
or bleed with a white
paper towel.

Move furniture out of area to
be cleaned. Place aluminum

foil or wax paper under
legs of furniture too heavy
to move to prevent wood
nishes from staining carpet.
Pin up furniture skirts
and draperies.

Pretreat spots and heavy
trafc areas with a Hoover

®

Cleaning Solution*. See

“Cleaning Solutions” section.
*Available at additional cost if

not included with your model.

1

Wrap cord around
the cord hooks for
convenient storage.
Attach the plug end to
the cord.

Cord storage:

NOTE: To prevent staining,
use plastic or aluminum foil
to protect wood or metal
surfaces from possible
water spray.

NOTE: To avoid damage
to wood oors underneath
area rugs or carpet, place
waterproof material (e.g.
plastic) underneath them
before cleaning.

5

1 42 3

Press the Clean Water
Solution Tank button on
handle. Tilt the Clean
Water Solution Tank out

and remove.

Fill Solution Tank with
solution. Replace
both caps.

Turn water cap counter­clockwise and pull up

to remove.

Fill Clean Water Tank with
hot tap water.

Remove and replace clean water solution tank:

WARNING

Use only HOOVER cleaning products intended for use

with this machine. (See the "Cleaning products" section in

this manual for details.) They are specially formulated for

use with your cleaner. Non-Hoover cleaning solutions may

harm the machine and void the warranty.

CAUTION

Do not ll with water above

140˚F (60˚C).

!!

!!

Getting started with your Power Path™ Pro:

6

5

Tilt the Clean Water

Solution Tank back onto
the handle until it clicks.

NOTE: Using more than the
recommended amount of cleaning
solution may cause excessive foaming.

CAUTION

Water will drip from the brushes and underside of the product after use and may puddle.

To avoid damage to wood and laminate ooring and to avoid potential slip hazard, after

use (a) do not leave the product on wood and laminate surfaces and move to a hard

surface and (b) place unit on absorbent material (such as a towel) to soak up drips.

!!

76

To rinse carpets and remove
excess solution, turn the
dial to "Rinse" and go over
carpets again.

To wash carpets, turn the

front dial on the Clean

Water Tank to "Wash".

7

NOTE: For best results, use straight, parallel strokes.
Overlap strokes by 1 in. to help prevent streaking.

1 42 3

Plug in. Step on the
handle release pedal to
put unit in
cleaning position.

Release the trigger and
slowly push forward over
the sprayed area. Then
slowly pull back toward
you without squeezing
trigger (dry stroke).
Continue using dry
strokes until little water
is visible passing through
the nozzle.

Step on the power pedal
to turn ON (I=ON). Press
the power pedal again to
turn OFF (0=OFF).

Squeeze trigger to apply
cleaning solution. Slowly
push forward then backwards
while squeezing the trigger
(wet stroke).

Using your Power Path™ Pro:

8

For best cleaning results, end with more

dry strokes. (Continue using dry strokes

until little water is visible passing through
the nozzle.)

NOTE: Empty Dirty Water Tank when the

motor sound becomes higher pitched and

there is a loss in suction (see “Automatic

shut-off”).

For best results, Hoover

®

recommends
rinsing carpet with water only. This
removes residual carpet cleaning solution.
Fill Clean Water, then turn knob to rinse
mode and repeat. For heavily soiled

areas, repeat. Avoid saturating carpet.

NOTE: It is best to alternate wet and dry

strokes as described above.

CAUTION

Do not clean over oor electrical outlets. Water
will drip from the brushes and underside of the

product after use and may puddle. To avoid

damage to wood and laminate ooring and

to avoid potential slip hazard, after use (a) do

not leave the product on wood and laminate
surfaces and move to a hard surface and (b)

place unit on an absorbant material

(such as a towel) to soak up drips.

!!

9

1

4

2 3

Grasp Dirty Water

Tank handle and

push latch to release.
Pull tank out at an
angle like this.

Replace lid by lining up
the hinge and pulling
latch down to lock. Latch
will line up with hinge and
snap when secured.

Empty the Dirty Water

Tank by pulling up on

the latch at the back
of the tank to open.

Remove lid and
empty tank.

WARNING

To reduce the risk of personal injury -

Unplug before cleaning or servicing.

!!

Emptying your Power Path™ Pro dirty water tank:

10

Automatic Shutoff:

5

Insert Dirty Water Tank at
an angle back into cleaner
until it clicks into place.

Your carpet washer is
equipped with a shut-off oat.
When the Dirty Water Tank

becomes full, the oat will

rise, shutting off the air ow

through the nozzle. A higher

pitched sound will come from

the motor. When activated,

empty the dirty water tank.

If the dirty water tank does
not appear full, turn off and
wait for the oat to reset. If

the oat repeatedly shuts off

the suction, empty the dirty
water tank.

For best results, use only

Hoover

®

brand cleaning
solution. Other solutions may
generate excessive foam
which will cause the oat to
shut off the suction.

11

1 2

Place handle in
upright position.

Slide the hose on the
tool's connector until it
locks. Push forward with
your thumb and on the
latch to remove.

CAUTION

Not to be used for grooming a pet.

!!

CAUTION

To reduce risk of injury from moving

parts – Unplug before servicing.

How to attach your Power Path™ Pro tools:

CAUTION

Use extra care when cleaning

on stairs. To avoid personal

injury or damage, and to

prevent the cleaner from

falling, always place cleaner

at bottom of stairs or on oor.

Do not place cleaner on stairs

or furniture, as it may result in

injury or damage.

!!

!!

12

Upholstery Tool: Multi-Floor Squeegee*:

*Select Models Only

The Upholstery Tool’s

built-in brush provides
scrubbing action.

The Multi-Floor Squeegee
extends cleaning from
carpet to hard oor.

Pivot squeegee on front
nozzle and snap back
to secure squeegee for
hard oor use.

NOTE: Tools are located and
stored in Mesh Storage Bag.

13

1 2 3

Open Accessory Hose Suction
Port at the bottom of the Dirty
Water Tank.

Insert hose end connector
by inserting rmly into
Suction Port.

Press the button on the
end of hose and pull
the hose and solution
connection from machine
to remove.

Close Accessory Hose
Suction Port door back
into place. Make sure
to close door to ensure
proper suction.

Using your Power Path™ Pro tools:

NOTE: Upholstery and
SpinScrub Powered
Hand Tool attach to the
hose in the same manner.

NOTE: Spot Treater Wand
attachment is the same
process as attaching
hose to the unit.

14

2

1

Press the trigger to
release air and uid.
Replace Hose and tools
in the Mesh Storage Bag.

Drain suction hose by turning
cleaner ON and holding
nozzle up for several minutes.
Do not press the trigger.

Disconnect hose and solution
tube from cleaner. Drain
solution tube by placing
round end in sink and raising
the trigger end at the hose
nozzle above your head.

After using tool:

15

1 2

Attach hose to the unit.
Follow steps "Using your
Power Path™ Pro Tools"
on page 13.

3

Dry hands and plug into

an outlet, then turn ON.

Gently press the tool
onto the fabric. Press the
trigger and slowly pull the
nozzle over the fabric.

Read “Before You Begin
Cleaning” instructions.

Be sure to check Hoover
Cleaning Guide on page 4
and the cleaning code on
your upholstery. Use your
cleaner only on upholstery
marked “W” or “W/S”.

CAUTION

To reduce risk of injury from

moving parts –

Unplug before servicing.

!!

How to clean upholstery with your Power Path™ Pro:

16

4

Overlap strokes by 1/2 in. to prevent
streaking. Make additional strokes
without pressing the trigger to remove
more solution.

For heavily soiled areas, repeat the
cleaning process.

For best cleaning results, Hoover®
recommends to rinse the upholstery
with water only. This removes residual
cleaning solution.

If additional cleaning is
necessary, wait until the
upholstery is completely
dry before using the
tool again.

Empty Dirty Water Tank
when the motor sound
becomes higher pitched
and there is a loss in
suction (see “Automatic
Shut-Off”).

When nished cleaning,
follow “After Cleaning”
and “After Using Tool”
instructions on page 14.

17

Cleaning the dirty water tank:

1 2

Remove the Dirty Water
Tank by pressing on latch
and pulling the tank out
at an angle.

Pull up on back latch to
open Dir ty Water Tank.
Remove top and rinse
tank with clean water.

LUBRICATION

The motor and brushroll are equipped
with bearings which contain

sufcient lubrication.

Additional lubricant could cause
damage. Do not add lubricant to

motor or brushroll.

Familiarize yourself with these home
maintenance tasks. Proper use and care of
your cleaner will ensure continued cleaning
effectiveness.

Any other servicing should be done by
an authorized service representative. If
appliance is not working as it should, has
been dropped, damaged, left outdoors,
or dropped into water, take it to a service
center prior to continuing use.

Note: During normal use, debris may
accumulate inside of dirty water tank. In
order to keep your unit functioning properly,
rinse out your dirty water tank with fresh
water after each use.

Keeping your Power Path™ Pro running properly:

18

3

To clean Dirty Water Tank,

place it under faucet and
dispense high pressure
clean water to backush
any loose debris.

4 5

Be sure to clean the
lter screen located in
the duct of the recovery
tank base.

Allow to air dry completely. Pull
up on latch, then back down to
lock. Latch will snap when locked.
Replace Dirty Water Tank back
onto unit until it snaps.

Note: The lter screen
is not removable.
Attempting to remove
the lter screen from the
tank may damage it

19

Cleaning the Nozzle:

31 2

Pull nozzle forward
to remove.

To prevent leaking, remove
Solution Tank and Dirty Water
Tank. With handle in upright
position, tilt carpet
washer back.

Pull up on nozzle latch to
unsnap nozzle from the
base of the
carpet washer.

NOTE: If lint or other debris becomes lodged
in nozzle, it can be removed for cleaning.

CAUTION

To reduce risk of injury from moving

parts – Unplug before servicing.

!!

Keeping your Power Path™ Pro running properly:

4

Rinse debris from
the nozzle.

20

5 6

Position nozzle onto

the base, making sure

to align the tabs at the

bottom of the nozzle with

the notches on the base.

Press down on nozzle
latch. It'll click.

STORAGE

Before storing:

• Empty Solution Tank and let
air dr y.

• Empty Dirty Water Tank,

rinse tank and lid thoroughly
with clean water and let

ai r d ry.

• Replace tanks on cleaner.

Allow brushes and
underside of carpet cleaner
to air dry thoroughly
before storing cleaner on a
carpeted or wood surface.

21

Cleaning SpinScrub Brushes:

Keeping your Power Path™ Pro running properly:

1 2 3

Flip cleaner on back. Grasp SpinScrub

Brushes and pull out.

Rinse off debris. Replace
SpinScrub Brushes by
lining up tab and pushing
back in.

22

Removing the flat belt:

CAUTION

To reduce risk of injury from moving

parts – Unplug before servicing.

!!

1 2 3

Flip cleaner on its back to
expose bottom of cleaner.
Make sure nozzle and
SpinScrub Brushes
are removed.

Keeping® your Power Path™ Pro running properly:

To access the belt,
remove the 8 screws.
Circles showlocation
of screws.

Flip cleaner to the
upright position.

Press the ON/OFF
button and the
handle release button
to loosen hood.

4

23

5 6

Pull up on hood and
move to side. Hood will
still be attached to unit.

Make sure unit is in upright
position. Slide off at belt and
replace with new belt.

To reassemble, reverse steps.

Belt: What to Buy

For replacement belts
please order part number
440006154 for tooth/

timing belt or 440006155

for at belt. To locate a
dealer nearest you, please
call 1-800-944-9200 or

visit our website at
www.hoover.com.

NOTE: Flat belt is smooth
while timing belt has teeth.

24

If you need further assistance:

If your product needs servicing within the warranty period, please
contact Customer Service at 1-800-944-9200; Mon-Fri 8am-7pm
EST. Always identify your carpet washer by the complete model
number when requesting information or ordering parts. (The
model number of the carpet washer is located on the data plate)

PLEASE DO NOT RETURN THIS CLEANER TO THE STORE.

Need Help?

Hoover Cleaning Solution Guide:

QUESTIONS OR CONCERNS?

Contact Us:

[phone]

For a Complete Troubleshooting Guide, see:

Twitter: @HooverUSA

Facebook: facebook.com/hoover

Do not return to store. See back of

product for model number.

WARNING

To reduce risk of re and electric
shock due to internal component

damage, use only Hoover



cleaning

products intended for use with the

appliance as noted below.

! !

For optimal performance
use Hoover brand
solutions, wipes and
spot cleaners available
at Hoover.com and
retailers nationwide.

Clean

Plus 2x

32 oz./64 oz.

Dual Power™
Pro
Carpet
Washer

Pet

Plus 2x

32 oz./64 oz.

Pro

Plus 2x

32 oz./64 oz.

Professional

Strength

50 oz.

25

Troubleshooting:

Any other servicing should be
done by an authorized service
representative.

USE TROUBLESHOOTING GUIDE
AS A FIRST STEP TO RESOLVE
ANY PROBLEMS YOU MAY BE
EXPERIENCING.

If appliance is not working as

it should, has been dropped,

damaged, left outdoors, or
dropped into water, call Customer
Service at 1-800-944-9200

for further instruction before

continuing use.

WARNING

To reduce the risk of personal injury -

Unplug before cleaning or servicing.

!!

PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION

Cleaner won’t run

1. Power cord not firmly plugged into outlet.

1. Plug unit in f irmly.

2. Blown f use or tripped breaker.

2. Check fuse or breaker in home. Replace fuse/reset
breaker in ho me.

3. Needs service.

3. Take to service center. To find nearest location, visit our
website at www.hoover.com or call 1-800-944-9200.

Cleaner won’t pick­up or low suction

1. Dirty Water Tank is not installed correctly. 1. Review Placing Dirty Water Tank in base of cleaner - Pg. 8.

2. Dirty Water Tank is full. 2. Empty Dirty Water Tank.

3. Dirty Water Tank is clogged. 3. Clean Dirty Water Tank.

4. Air path is clogged. 4. Unclog air path.

Water escaping
from Cleaner

1. Dirty Water Tank is full. 1. Empty Dirty Water Tank.

2. Dirty Water tank is not installed correctly. 2. Review Placing Dirty Water Tank in base of cleaner 8.

3. Clean Water Solution Tank not installed
properly.

3. Review Clean Water Solution Tank Installation.

Cleaner won’t
dispense

1. Clean Water Solution Tank is empty. 1. Fill Clean Water Solution Tank.

2. Clean Water Solution Tank not installed
properly.

2. Review Clean Water Solution Tank Installation.

3. Needs service. 3. Take to service center. To find nearest location, visit our

website at ww w.hoover.com or call 1-800-944-9200.

Hose nozzle will not
spray after filling
the Clean Water
Tank or Detergent
Container.

1. Air is trapped in the pump and hose.

2. The connection to the tool port is loose.

1. Turn on the cleaner. If hose does not spray, prime the
pump by lowering the hose down to the floor and hold the
trigg er for up to 1 minute.

2. Ensure that the Hose is securely connected to the hose
connection.

Motor noise
becomes
high-pitched

1. Dirty Water Tank is full. 1. Empty Dirty Water Tank.

2. Dirty Water Tank is clogged. 2. Clean Dirty Water Tank.

3. Air path is clogged. 3. Unclog air path.

4. The float in the Dirty Water Tank has been
activated.

4. Review Emptying & Cleaning the Dirty Water Tank.

Brushrolls are not
spinning

1. Belt needs to be changed. 1. Refer to how to change belt.

2. Something is jammed in the brushroll. 2. Remove jammed item from cleaner with unit turned off

and unplugged.

26

ANY SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE
REPRESENTATIVE Call 1-800-944-9200 USA & Canada

In the event that fur ther assistance is required, visit an authorized service
center. Find one nearest you by visiting our website at www.hoover.com.
Costs of any transportation to and from any place of repair are to be paid
by the owner. Always identify your product by the model number and
manufacturing code when requesting information or ordering replacement
parts. (The model number and manufacturing code are on the back of
the product).

LIMITED TWO YEAR WARRANTY (DOMESTIC USE)
WHAT THIS WARRANTY COVERS

When used and maintained in normal household use and in accordance with
the Owner’s Manual, your HOOVER

®

product is warranted against original
defects in material and workmanship for a full one year from date of purchase
(the “Warranty Period”). During the Warranty Period, Hoover® will provide
labor and parts at no cost to you to correct any such defect in products
purchased in the United States, U.S. Military Exchanges and Canada.

HOW TO MAKE A WARRANTY CLAIM

If this product is warranted, take or send the product to either a Hoover

®

Sales and Service Center or Hoover® Authorized Warranty Service Dealer
along with proof of purchase. For an automated referral to authorized ser vice
outlets in the U.S.A., phone: [phone] OR visit Hoover® online at
www.hoover.com. For additional assistance or information concerning this
Warranty or the availability of warranty ser vice outlets, call the Hoover®
Consumer Response Center, Phone [phone], Mon-Fri 8am-7pm
EST. In Canada, contact Hoover® Canada, Carson Building, 100 Carson St.,
Etobicoke, Ontario M8W 3R9, Phone: [phone],
Mon-Fri 8am-7pm EST.

WHAT THIS WARRANTY DOES NOT COVER

This warranty does not cover: use of the product in a commercial operation
(such as maid, janitorial and equipment rental services), improper

maintenance of the product, damage due to misuse, acts of God, nature,
vandalism or other acts beyond the control of Hoover

®

, owner’s acts
or omissions, use outside the country in which the product was initially
purchased and resales of the product by the original owner. This warranty
does not cover pick up, delivery, transportation or house calls, however, if
you mail your product to a Hoover® Sales and Service Center for warranty
service, cost of shipping will be paid one way.

This warranty does not apply to products purchased outside the United
States, including its territories and possessions, outside a U.S. Military
Exchange and outside of Canada. This warrant y does not cover products
purchased from a party that is not an authorized retailer, dealer, or distributor
of Hoover

®

products.

OTHER IMPORTANT TERMS

This warranty is not transferable and may not be assigned. This Warranty
shall be governed and construed under the laws of the state of Ohio.
The Warranty Period will not be extended by any replacement or repair
performed under this Warranty.

THIS WARRANT Y IS THE E XCLUSIVE WARRANTY AND REMEDY
PROVIDED BY HOOVER

®

. ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR PARTICULAR PURPOSE, ARE DISCLAIMED. IN NO EVENT WILL
HOOVER® BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER
OR ANY PART Y CLAIMING THROUGH OWNER, WHETHER BASED IN
CONTRACT, NEGLIGENCE, TORT OR STRICT PRODUCTS LIABILITY OR
ARISING FROM ANY CAUSE WHATSOEVER. Some states do not allow the
exclusion of consequential damages, so the above exclusion may not apply
to you. This warranty gives you specific rights; you may also have others that
vary from state to state.

SERVICE & WARRANTY

SERVICE INFORMATION