Page 1
freedom
USER
INSTRUCTIONS
®
Freedom IM.indd 1 01/06/2008 07:54:29
Page 2
2
User manual - This cleaner should only be
used fo r its intended purpose as descr ibed in
these instructions. Ensure that these are fully
understood before operating this appliance.
Only use attachments recommended or
supplied by Hoover.
When using cleaning tools ensure that the
cleaner is kept in the upright (parked)
position. This will avoid possible damage to
the carpet or floor covering. When cleaning
stairs DO NOT position the cleaner above
you.
STATIC ELECTRICITY. Some carpets can
cause a small build up of stati c electricit y. Any
static discharge is not hazardous to health.
DO NOT use your cleaner out of doors,
on any wet surface or for wet pick up.
Keep hands, feet, loose clothing and hair
away from rotating brushes.
DO NOT pick up hard or sharp objects,
matches, hot ashes, cigarette ends or other
similar items.
DO NOT pick up flammable liquids such as
cleaning fluids, petrol etc. or their vapours.
Congratulations on the purchase of your
new Hoover Freedom.
This highly advanced machine - with new
Airvolution technology unique to Hoover makes cleaning easier and more efficient.
Please take the time to read this manual
carefully.
You’ll be ready to make the most of the
special features only the new Hoover
Freedom can offer!
This appliance is double insulated and must not
earthed.
The plug is fitted with a 13 amp fuse.
IMPORTANT:The wires in the mains lead are
coloured in accordance with the following
code:
Blue - NEUTRAL
Brown - LIVE
IMPORTANT SAFETY REMINDERS
Aerosol sprays may be flammable. DO
NOT spray near cleaner.
SUPPLY CORD. DO NOT run over the
supply cord when using your cleaner or
remove the plug by pulling on the supply
cord.
FAULTS. DO NOT continue to use your
cleaner if it appears to b e faulty. If the supply
cord is damaged stop using the cleaner
IMMEDIATELY. The supply cord must be
replaced by an authorised Hoover service
engineer to avoid a safety hazard.
AFTER USE. Switch the cleaner off and
remove the plug from the electricity supply.
Always switch off and remove the plug before
cleaning the appliance or attempting any
maintenance task.
Safety with children, elder ly or the infirm:
Do not let children play with the appliance or
its controls. Please supervise the use of the
appliance by o lder chil dren, the elderly or the
infirm.
HOOVER SERV ICE. To ensure the continued
safe and efficient operation of this appliance
we recommend that any ser vicing or repairs
are only carried out by an authorised Hoover
service engineer.
WARNING!
ELECTRICITY CAN BE
EXTREMELY DANGEROUS
In the unlikely event that any item is missing or you experience any problems with the product
DO NOT TAKE IT BACK TO THE SHOP
Please contact the Hoover customer helpline:
Tel: 08705 400 600
Fax: 01204 556149
Email: service@hoovercandy.com
Should any faults occur with your cleaner during the first 12 months contact the Hoover Customer
Helpline on the number above.
If you are having difficulty in obtaining filters or any other accessories for your cleaner contact the
Hoover Customer helpline or order online at www.hooverspares.com
Freedom IM.indd 2 01/06/2008 07:54:29
Page 3
3
FREEDOM
The ultra versatile
way to clean
everywhere.
When first unpacking your
cleaner please check all items
are included:
Cleaner body
Removable Handle
Explorer Lance
Dusting Brush
Pet Hair Remover Turbo Brush
Allergen Remover Turbo Brush*
(*certain models only)
If any parts are missing, call
the Hoover helpline on
08705 400 600
CORD CLIP
LANCE RELEASE
BUTTON
ON/OFF BUTTON
EXPLORER
LANCE
HANDLE PARK
DUSTING BRUSH
CARPET CARE
CONTROL SELECTOR
FOOT HOSE
2 POSITION
LOCK PEDAL
UPPER CORD
HOOK
CARRY HANDLE
LONG STRETCH
HOSE
BIN
RELEASE
BUTTONS
PET HAIR REMOVER
TURBO BRUSH
PRE MOTOR
FILTERS ACCESS
BUTTON
ONE TOUCH BIN
EMPTY BUTTON
LOWER CORD
HOOK
EXHAUST FILTER
GETTING TO KNOW YOUR CLEANER
DUST BIN
CLIPS
DUST BIN
ALLERGEN REMOVER
TURBO BRUSH*
(certain models only)
3
Freedom IM.indd 3 01/06/2008 07:54:30
Page 4
4
PREPARING YOUR CLEANER
Connect the stretch hose to the
handle by plugging the hose cuff
into the back of the handle until it
clicks in place.
Remove the accessories from
the main packaging You should
nd the following:
Removable Handle
Explorer Lance
Dusting Brush
Pet Hair Remover Turbo Brush
Allergen Remover Turbo
Brush*
Allergy Defender Granules*
* Certain Models only
1
Fit the pet hair remover turbo brush into
the dust bin below the carry handle.
4
4
Connect the explorer lance to the
handle.
2
Assemble the dusting brush onto the
rear of the handle.
5
Fit the foot hose into the hood.
Fit the explorer lance and handle
onto the main body of the cleaner.
Ensuring the end of the lance
slides over the lance guide posts.
3
6
Freedom IM.indd 4 01/06/2008 07:54:31
Page 5
5
CARPET CARE CONTROL SELECTOR
The carpet care control selector raises and lowers the
height of the nozzle.
Ensure that the cleaner is in an upright (parked) position.
Slide the knob to position best suited to depth of carpet
pile.
Try various settings until you get the best results for your
carpet.
NOTE: Using this cleaner for loop carpets or carpets with
pile greater than 30mm is not recommended. Please
consult the oorcare/carpet manufacturer’s recommended
cleaning instruction before vacuuming.
!
IMPORTANT! When cleaning hard floors
such as vinyl or linoleum, move the selector
knob to the HARD floor position. Failure to
do so may cause damage to the floor
surface.
!
CLEANER LOCK RELEASE
The cleaner can be adjusted to 3 different positions.
Upright - For storage and when using tools.
Position 1 - For general cleaning on carpets and
ooring.
Position 2 - For reaching under furniture and some
maintenance tasks.
Unlock the cleaner by pressing down on the pedal
with your foot.
Press the pedal a second time and lower the cleaner
to the oor.
POWER SWITCH
To switch the cleaner on or off press the On/Off
button on the side of the cleaner.
Freedom IM.indd 5 01/06/2008 07:54:32
Page 6
6
CLEANING TOOLS
!
IMPORTANT! When using cleaning tools, the cleaner must be kept in the upright position, particularly when
cleaning stairs.
!
The following accessories are available with the product:
Explorer lance
Dusting Brush
Pet Hair Remover Turbo Brush
Allergen Remover Turbo Brush* (certain models only)
All accessories can t directly onto the handle of the product or onto the explorer lance tool. Combine accessories
depending on use.
EXPLORER LANCE
1
2
Press the lance release button and pull the
explorer lance together with the handle from the
main body of the cleaner. It will immediately be
ready for over head cleaning and hard to reach
areas e.g. behind radiators etc.
If desired, it is possible to use the handle
without the lance.
Freedom IM.indd 6 01/06/2008 07:54:34
Page 7
7
CLEANING THE STAIRS
HANDLE PARK CORD STORAGE
It is dangerous to place the cleaner above you when
cleaning stairs. Place the cleaner against the bottom
step facing the stairs.
ALWAYS work with the cleaner below you.
For more efcient storage remove the handle from
the main body of the cleaner by pressing the lance
release button. Remove the lance from the handle
and return to its original position on the cleaner.
Park the handle on the side of the cleaner.
Turn the cleaner off and remove the plug. Wind the
power cord around the cord storage hooks.
When the handle is in the handle park position wind
the power cord around the lower cord storage hook
and the carry handle.
!
IMPORTANT! Extra care must be taken when
using the hose on the stairs. If the hose
becomes blocked it can exert a strong pull in
the direction of the cleaner.
!
Freedom IM.indd 7 01/06/2008 07:54:35
Page 8
8
EMPTYING THE DUST BIN
DUST BIN MAINTENANCE
ALLERGY AND ASTHMA SUFFERERS
Hold the container using the carry handle
over the bin and press the bin empty button.
The dust container door will automatically
open.
Wrap the lower bin in a plastic bag and close
the bag tighty around the dust container.
Once emptied, gently tap or shake the
container to release any excess dust.
Press the bin empty button to empty the dust
into the plastic bag. Close the bag quickly
and dispose of it immediately.
Lift the bin upper section containing the
separation unit from the lower section.
Press the bin release buttons and remove the
dustbin from the cleaner.
Reassemble the bin upper section. Push
clips back to fully close the bin then refit the
dustbin to the cleaner.
Use a cloth or the dusting brush to remove
excessive dust from the separation unit’s
surface.
Place the bin on a flat surface and release the
clips from either side of the dust container.
!
IMPORTANT! Do not ll above the max
level mark shown on the bin.
!
When emptying any vacuum cleaner it is difcult to
avoid exposure to dust. To minimize this risk, please
follow these instructions:
1 1
1
2
2
2
3
3
4
Freedom IM.indd 8 01/06/2008 07:54:37
Page 9
9
Lift the tab on the exhaust lter cover grille and
remove from the cleaner.
Wash the exhaust lter under hand warm water
until the water runs clean. Remove excess water
by shaking and leave to dry for 24 hours.
Refit filter only when completely dry.
DO NOT USE HOT WATER OR
DETERGENTS.
Remove the exhaust lter.
CLEANING THE EXHAUST FILTER
CLEANING THE PRE MOTOR FILTERS
Press the bin release buttons
and remove the dust bin from
the cleaner.
Remove the pet hair remover
turbo brush from the top cover
of the cleaner.
1
1
Place the bin on a at surface
and press the lter access
button to open the top cover of
the bin.
2
2
Remove the BLUE lter pack
(containing the HEPA and foam
lter).
3
3
Separate the GREY foam lter
from the BLUE HEPA lter pack
using the tab provided.
Gently tap both lters against
the side of a bin to release
excess dust.
Wash the GREY foam lter
thoroughly under hand warm
water until the water runs
clean.
Remove excess water by
shaking and leave to dry for
24 hours.
DO NOT USE HOT WATER
OR DETERGENTS.
4
Wash the BLUE HEPA lter
thoroughly from the inside
under hand warm water until
the water runs clean.
Remove excess water by
shaking and leave to dry for 24
hours. When completely dry
reassemble and refit filters to
cleaner.
DO NOT USE HOT WATER
OR DETERGENTS.
65
!
IMPORTANT! For optimum performance,
always keep your lters clean.
!
!
!
IMPORTANT! For optimum performance,
always keep your lters clean. We recommend
that the exhaust lter should be washed every
3 MONTHS.
IMPORTANT! For optimum performance, shake off excess dust from the lters regularly.
We recommend that the GREY foam lter and the BLUE hepa lter are washed every 3 MONTHS.
!
!
Freedom IM.indd 9 01/06/2008 07:54:38
Page 10
10
CHANGING THE BELT / AGITATOR
If your cleaner is not picking up efciently, the belt or brushes (or both) may need replacing, but rst please make
sure you have:
• Emptied the dust container
• Cleaned the lters
• Checked for blockages
CLEARING A BLOCKAGE
IMPORTANT: Switch the cleaner off and remove
the plug from the electricity supply before
dismantling cleaner
!
IMPORTANT: Switch the cleaner off and remove the plug from
the electricity supply before dismantling cleaner
!
Remove the carpet care control knob.
Turn the cleaner over and remove 5
retaining screws attaching the brush
guard to the base.
Turn the cleaner over and remove the hood.
Remove brush assembly and check for wear
on the belt. Loop the new belt around the
motor and brush assembly.
Hold the brush assembly and stretch the belt until
the brush can be slotted back into the cleaner
housing.
Rotate the brush to ensure movement of the belt.
Refit the hood ensuring the lugs along the front
are located in the slots on the front edge of the
baseplate. Secure the hood with 5 retaining screws.
Refit the carpet care control knob.
1
2
3
4
5
6
If cleaning tools were in
use check the cleaning tool
and the removable handle.
Check the hose by removing
it from the cleaner, stretching
it to full length.
Turn the cleaner over and
rotate the brushes until
they are free to rotate.
Check for a blockage in
the hose socket. Use a
flexible rod to remove any
obstruction.
Open the pet hair or
allergen remover turbo
brush at each side, lift
cover and remove the
blockage.
Freedom IM.indd 10 01/06/2008 07:54:40
Page 11
11
Genuine HOOVER Spares
Tel. 01204 556 111
www.hooverspares.com
Always replace parts with genuine Hoover spares. When ordering parts always
quote your model number.
Hoover Customer Helpline
Should any faults occur with your cleaner during the first 12 months
contact the Hoover Customer Helpline on the number below.
Tel: 08705 400 600
Fax: 01204 556149
Email: customer.service@hoovercandy.com
Hoover have a computerised nationwide service network of over 500 engineers
who will quickly respond to your call and guarantee your repair for 12 months.
GUARANTEE STATEMENT
The guarantee conditions for this appliance are as defined by our representative in
the country in which it is sold. Details regarding these conditions can be obtained
from the dealer from whom the appliance was purchased. The bill of sale or recipt
must be produced when making any claim under the terms of this guarantee.
Subject to change without notice.
Environment - WEEE Directive
This appliance is marked according to the European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly you will help prevent potential
negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as houshold
waste. Instead it shall be handed over to the appliance collection point for recycling of
electrical and electronic equipment.
Disposal must be carried out in accordance with the local environmental regulations
for waste disposal.
For more detailed information about treatment, recovery and recycling of this product,
please contact your local city ofce, your household waste disposal service or the
shop where you purchased the product.
Quality
BSI ISO 9001
Hoover’s factories have been independently assessed for quality . Our products are
made using a quality system which meets the requirements of ISO 9001
Quality and the Environment
As the owner of a new Hoover product we would like to tell you more about the high
standards we have set in Quality and the Environment
USE ONLY HOOVER SPARES
SPARE PARTS CODE
HEPA FILTER AND FOAM U48- 35600834
EXHAUST FILTER T95- 35600835
AGITATOR Y22-35600837
BELT V30-35600838
HOSE D102-35600836
PET HAIR TURBO BRUSH J34-35600840
ALLERGEN REMOVER BRUSH J33-35600839
Freedom IM.indd 11 01/06/2008 07:54:40
Page 12
12
WARNING
A thermal cut out switches off the cleaner to prevent
overheating if it is used when full or there is a blockage or
dirty filters. If this should happen switch off, unplug and
correct the fault.
It will take approximately 30 minutes for the cut out to
automatically reset.
IMPORTANT
DO NOT RUN OVER THE POWER SUPPLY CORD
AS THIS COULD DAMAGE THE SUPPLY CORD
INSULATION.
User checklist
If your cleaner is not working properly run through the
following checklist.
1. Is there a working electricity supply to the cleaner?
Check with another electrical product.
2. Is the dust container full or choked with fine dust?
To empty the dust container see instructions on P8.
3. Is the hose blocked?
To clear a blockage see instructions on P10.
4. Is there a blockage in the cleaner base?
To clear a blockage, see the instruction on P10.
5. Are the filters blocked?
To clean filters, see the instruction on P9.
6. Is the nozzle height set correctly?
To set the carpet height selector, see the instruction on p5.
7. Are the brushes rotating correctly?
To check the brushes, see the instructions on p10.
8. Has the cleaner overheated? If so, it will take about 30
minutes to reset.
If there is any doubt call the Hoover Customer Helpline 08705 400 600 for
advice. They may be able to assist you over the telephone.
Freedom IM.indd 12 01/06/2008 07:54:40
Page 13
Hoover Limited
Pentrebach
Merthyr Tydfil
Mid Glamorgan
CF48 4TU
HOOVER CUSTOMER HELPINE
08705 400 600
© 2008 0565-5325 - 01
®
Freedom IM.indd 13 01/06/2008 07:54:40
Loading...