Visit our website at hoover.com for more information or for video instruction for this Hard Floor Cleaner.
Follow the authorized dealer locator link to find the Hoover® authorized dealer nearest you or call
1-800-944-9200 for an automated referral of Hoover® authorized dealer locations (U.S. only) or to speak
with a customer service representative; Mon-Fri 8am-7pm EST.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
2
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
When using an electrical appliance, basic precautions should always be
followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING: TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:
• Fully assemble before operating.
• Operate cleaner only at voltage specified on data plate on lower handle of cleaner.
• Do not leave appliance when plugged in. Unplug from outlet when not in use and
before cleaning or servicing.
• Use indoors only.
• Use only HOOVER
the “Cleaning Products” section of this manual.)
• Do not allow to be used as a toy. Not intended for use by children age 12 and
under. Close supervision is necessary when used near children. To avoid injury
or damage, keep children away from product, and do not allow children to place
fingers or other objects into any openings.
• Use only as described in this manual. Use only manufacturer’s recommended
attachments and products.
• Do not use with damaged cord or plug. If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, take it to a
service center prior to continuing use.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull
cord around sharp edges or corners. Do not place product on cord. Do not run
appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and
moving parts.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs. To avoid personal injury or damage, and to
prevent the cleaner from falling, always place cleaner at bottom of stairs or on floor.
Do not place cleaner on stairs or furniture, as it may result in injury or damage.
• Do not use to pick up flammable or combustible materials, such as gasoline, or
fine wood sandings, or use in areas where they may be present.
• Connect to a properly grounded outlet only. See Grounding Instructions.
• Not intended for use on carpets.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches,
or hot ashes.
• Do not use without Tanks or Filters in place.
• Do not clean over floor electrical outlets.
• WARNING: This product contains chemicals known to the State of California to cause
cancer, birth defects or reproductive harm.
®
cleaning products intended for use with this machine. (See
WASH HANDS AFTER HANDLING.
3
CAUTION - TO REDUCE THE RISK OF DAMAGE:
GROUNDINGOUTLET BOX
• Avoid picking up hard, sharp objects with this product, as they may cause damage.
• Store appropriately indoors in a dry place. Do not expose machine to freezing
temperatures.
• Do not use sharp objects to clean out hose as they can cause damage.
• To assist in reducing drying time, be certain the area is well ventilated when using
detergents and other cleaners with this machine.
• With brushes on, do not allow cleaner to sit in one location for an extended
period of time, as damage to the floor can result.
• Water will drip from the brushes and underside of the product after use and may
puddle. To avoid damage to wood and laminate flooring and to avoid potential
slip hazard, after use (a) do not leave the product on wood and laminate surfaces
and remove to a hard surface and (b) place unit on absorbent material (such as
a towel) to soak up drips.
• Check and follow flooring manufactures warranty and recommendations
regarding the use of hard floor cleaning machines prior to using this product on
your sealed hard floors.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This appliance is equipped with a cord having an
equipment-grounding conductor (C) and grounding plug (A). The plug must be
inserted into an appropriate outlet (B) that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment-grounding conductor
can result in the risk of electric shock. Check with a qualified electrician or service
person if you are in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the appliance - if it will not fit the outlet, have a
proper outlet installed by a qualified electrician. This appliance is for use on a
nominal 120-volt circuit and has a grounding plug that looks like the plug (A)
illustrated in Fig. 1. A temporary adapter (D) may be used to connect this plug to
a 2-pole receptacle (E) if a properly grounded outlet is not available (Fig. 2). The
temporary adapter should be used only until a properly grounded outlet (B) can
be installed by a qualified electrician (Fig. 1). The green colored rigid ear, lug, or
the like (F) extending from the adapter must be connected to a permanent ground
(G) such as a properly grounded outlet box cover (Fig. 2). Whenever the adapter
is used, it must be held in place by a metal screw. NOTE: In Canada, the use of a
temporary adapter is not permitted by the Canadian Electrical Code.
1
A
C
2
B
D
4
D
F
G
E
FEATURES
1
2
4
7
11
FEATURES
FRONT
3
12
5
6
14
13
8
9
16
15
17
10
BACK
1. D-Shaped Handle
2. Clean Boost™ Trigger
3. Solution Trigger
4. Folding Handle Release Button
(FH40165 & FH40170 series)
5. Mode Selection
6. ON/OFF Switch
7. Carry Handle
8. Clean Water/Solution Tank
Release Button
9. Clean Water/Solution Tank
10. Nozzle Release
11. Nozzle
12. Cord Clip
13. Cord Storage Hook (rotates)
14. Dirty Water Tank Release Button
15. Dirty Water Tank
16. Cord Storage Hook
17. Handle Release Pedal
5
1. CARTON CONTENTS
CARTON CONTENTS FOR
FLOORMATE
FH40150 SERIES
A. Hard Floor Cleaner Base
(Floormate FH40150 Series)
B. Upper Handle
C. SpinScrubTM Multi-Floor Brush
(assembled in unit)
D. Screw
E. Hard Floor Cleaning Detergent
F. Removable Nozzle
Remove all parts from carton and
identify each item shown.
Make sure all parts are located
before disposing of packing
materials.
CARTON CONTENTS FOR
FLOORMATE DELUXE
FH40160 SERIES
A. Hard Floor Cleaner Base
(Floormate Deluxe
FH40160 Series)
B. Upper Handle
C. SpinScrub™ Wood Floor Brush
(assembled in unit)
D. SpinScrub™ Tile & Grout Brush
E. Screw
F. Hard Floor Cleaning Detergent
G. Removable Nozzle
Remove all parts from carton and
identify each item shown.
Make sure all parts are located
before disposing of packing materials.
1.1
A
FH40150 SERIES
1.2
A
FH40160 SERIES
D
C
B
F
C
B
G
D
E
E
F
CARTON CONTENTS FOR
FLOORMATE DELUXE
FH40165 & FH40170 SERIES
A. Hard Floor Cleaner Base
(Floormate Deluxe FH40165 &
FH40170 Series)
B. SpinScrub™ Wood Floor Brush
(assembled in unit)
C. SpinScrub™ Tile & Grout Brush
D.* Hard Floor Cleaning Detergent
*Number of bottles may vary by
model
E. Removable Nozzle
Remove all parts from carton and
identify each item shown.
Make sure all parts are located
before disposing of packing materials.
1.3
A
FH40165 & FH40170 SERIES
6
B
C
D
*
E
2. HOW TO ASSEMBLE
ATTACH HANDLE
FH40150 & FH40160 SERIES
NOTE: PHILLIPS SCREWDRIVER NEEDED
FOR ASSEMBLY.
2.1 Position upper handle and slide down into
hard floor cleaner base.
2.2 Insert screw and tighten with screwdriver.
HOW TO FOLD HANDLE
FH40165 & FH40170
2.3 Simply rotate handle to upright position until
it locks into place to get started.
2.4 For product storage, press folding handle
release button and rotate handle down.
SERIES
ATTACH NOZZLE
2.5 Remove nozzle from packaging. Align
nozzle’s 2 hooks with 2 slots on front of base.
2.6 Tilt nozzle upwards until latch (A) clips in
place.
2.1
2.3
2.5
2.2
2.4
2.6
A
7
3. GENERAL OPERATION
Your HOOVER
tile and sealed wood. It is not intended for use on carpet or rugs.
To prevent damage to wood floors, follow the flooring manufacturer’s cleaning recommendations.
If using cleaner on sealed wood floors, inspect floor surface for worn finish, bare wood or separated
joints. Do not use FloorMate™ Hard Floor Cleaner to clean sealed wood floors if any of these conditions
exist.
®
FloorMate™ Hard Floor Cleaner is to be used on non-carpeted floor surfaces such as vinyl,
!!
CAUTION
THE TANKS (when facing unit)
Clean Water/Solution Tank (right side)
The Solution Tank holds detergent and water that
is to be dispersed onto the surface being cleaned.
!!
WARNING
To reduce the risk of personal injury, unplug
before cleaning or servicing. Do not use
cleaner without tank in place.
How to Fill
Place cleaner handle in upright, locked position.
3.1 To remove tank, squeeze release button (A) and
pull tank straight out. Carry tank to sink.
3.2 Rotate tank cap counter-clockwise and lift up to
remove cap (B).
3.3 Fill tank to fill line with warm water.
IMPORTANT
Check for worn spots or joint separations before
using, as these conditions could lead to damaged
flooring when using water to clean floor.
3.4 Turn cap upside down to serve as a
measuring cap.
3.5 For FloorMate FH40150 Series, fill measuring
cap to fill line once (3/4 oz - 22 ml) with Hoover® 2x
Multi-Floor Plus Cleaning Solution and pour cleaning
concentrate into Solution Tank.
For FloorMate Deluxe FH40160/FH40165/FH40170
Series, fill measuring cap to fill line twice (1.5 oz - 44
ml) and pour cleaning concentrate into Solution Tank.
3.6 Replace cap. Rotate cap clockwise until it locks
in place (C). Cap must be locked in place for proper
performance and to prevent leaking.
3.7 Slide tank straight into position until latch snaps
in place.
3.1
3.3
3.5
3.7
3.2
A
B
3.4
3.6
C
8
4. HOW TO USE
HANDLE RELEASE PEDAL
4.1
A
Step on pedal (A) to
lower handle to
operating position.
Handle does not lock
into a single position,
but “floats” to allow
convenient operation.
TRANSPORTING
4.3
To move your cleaner
from room to room, put
handle in upright
position, tilt cleaner
back on rear wheels
and push forward.
4.4
B
The cleaner may also
be lifted using the carry
handle (B) on front of
cleaner.
ON/OFF SWITCH
4.2
A
CORD STORAGE
4.5
C
Enrouler le cordon dans
le sens horaire autour
des deux crochets pour
cordon (C). Pour un
rangement pratique,
raccorder la fiche au
cordon.
Push switch (A) once to
turn cleaner ON. Push
switch again to turn
cleaner OFF.
5. HOW TO EMPTY
Dirty Water Tank
(left side when facing unit)
When to Empty
An automatic suction shut-off is built into the dirty
water tank to prevent the tank from overflowing.
When the shut-off activates, the cleaner will not pick
up water or debris and the sound of the motor will
change. The dirty water tank is full and must be
emptied.
How to Empty
5.1 To remove tank, press down on release button
(A) and pull tank straight out.
5.2 Release tabs (B & C) on each side of the dirty
water tank to unlock the top portion of the tank.
!!
WARNING
To reduce the risk of personal injury, unplug
before cleaning or servicing. Do not use
cleaner without tank in place.
5.1
A
9
5.2
B
C
5.3 Pull up on tank lid to separate from the base.
5.4 Pour dirty water into sink.
5.5 Check foam filter for debris before reassembly. If
filter has debris, rinse with water.
5.6 When finished emptying the tank, simply place lid
back onto the tank and make sure to latch the tabs
on each side back into the locked position.
5.7 Tilt tank straight into position until latch snaps in
place.
5.3
5.4
5.55.7
6. HOW TO CLEAN
RECOMMENDED CLEANING SEQUENCE
NOTE: Your HOOVER® FloorMate™ Hard Floor Cleaner may be used to clean wood floors that have been
sealed with a polyurethane coating and can be cleaned with water.
!!
CAUTION
To prevent damage to wood floors, follow the flooring manufacturer’s cleaning recommendations. If using
cleaner on sealed wood floors, inspect floor surface for worn finish, bare wood or separated joints. Do not
use FloorMate
TM
Hard Floor Cleaner to clean sealed wood floors if any of these conditions exist.
6.1 Vacuum floor to remove loose dirt, hair and
debris.
®
6.2 Fill Clean Water Solution Tank with Hoover
Multi-Floor Plus Cleaning solution and water (refer to
3.1 thru 3.7).
2X
IMPORTANT
Do not use solvent based cleaning concentrates
in your cleaner. Do not use any type of wax in
your cleaner.
Dry hands and plug cleaner into a properly
grounded outlet.
6.3 Step on handle release pedal and lower handle
to operating position.
6.4 Turn cleaner ON.
!!
CAUTION
Do not clean over floor electrical outlets.
10
6.1
6.4
6.3
!!
CAUTION
Water will drip from the brushes and underside of the product after use and may puddle. To avoid damage
to wood and laminate flooring and to avoid potential slip hazard, after use A) do not leave the product on
wood and laminate surfaces and remove to a hard surface and B) place unit on absorbent material (such
as a towel) to soak up drips.
6.5 Wash Mode - Lowers the SpinScrub™ brushes
to make contact with the floor for scrubbing action.
6.6 Dry Mode - Raises the SpinScrub™ brushes
off of the floor and also stops the spinning of
the brushes.
6.7 Scrub Mode - (FH40170 Series only) Lowers the
SpinScrub™ brushes to the floor and stops the
suction for extra cleaning with solution and water.
Switch to dry mode to pick up any remaining
dirty water.
6.8 To release solution, squeeze trigger (A)
6.9 Slowly move cleaner forward and backward over
area to be cleaned. Squeeze trigger to release
solution as needed.
6.10 Overlap strokes by one inch to help prevent
streaking. The cleaner’s suction will pick up the dirty
water throughout cleaning.
6.11 To remove those tough stains, apply extra
cleaning solution by squeezing the trigger (B) as you
normally would and also pressing the Clean Boost™
trigger (C) at the same time.
To greatly enhance drying of the floor surface,
release trigger. Continue to move cleaner over the
area to pick up the dirty solution.
Switch to dry mode to pick up any remaining
dirty water.
6.56.6
6.7
6.9
6.8
6.11
C
A
B
To continue cleaning another area, repeat steps 6.8
through 6.10.
NOTE: When cleaning sealed wood floors, make
sure all areas are completely dry. Ensure that no
water remains on the floor.
Empty dirty water tank when the motor sound
becomes higher in pitch and there is a loss of
suction.
PICKING UP SPILLS
Your cleaner may also be used to pick up small liquid
spills one and a half quarts or less in Dry Mode,
never to exceed 1/4 inch in depth on non-carpeted
floors. Release the trigger and continue to move
cleaner over the area to pick up the spill.
!!
CAUTION
Do not use the cleaner to pick up flammable or
combustible liquids or chemicals.
11
Loading...
+ 24 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.