Review this manual before
operating cleaner
This cleaner was inspected and packaged carefully before being
shipped from the factory. If you should happen to need assistance
during assembly or operation, call
l-800-944-9200 for automated referral of authorized service
outlet locations ( U.S. only ) or
l-330-499-9499 to speak with a representative in our
Consumer Response Center.
1
DO NOT RETURN THIS PRODUCT TO THE STORE.
Fill in and retain
The model and serial number are located on the bottom of the cleaner.
For your personal records, please enter the COMPLETE model and
serial number in the spaces provided and retain this information.
Your cleaner is model
and has serial number
It is suggested that you attach your sales receipt to this owner’s
manual. Verification of date of purchase may be required for warranty
service of your Hoover product.
Save
Index
Assembling Cleaner ......................................
Cleaner Descriptions
Cleaning Effectiveness
How To Use
Cleaning Tools ........................................
Power Nozzle ..............................................
Suction Regulator
To Clean Stairs
If You Have a Problem
Important Safeguards
Lubrication
Maintenance
Cleaning
Clearing Obstructions
Replacing Agttator
Replacing Bag
Replacing
Service .............................................................
Storage.............................................................
1
......................................................
Secondary
Beft
.....................................
Per Amp
......................................
...........................................
....................................
.......................................
Fitter
.............................
...................................
.....................................
.....................................
Rating..
.....................
5-6
3-4
.17
....
6-9
16
16
.I3
12
15
16-11
13-15
17
10
Q
1991 The Hoover Company
7
6
9
2
8
UL
0
lmwwtant Safeauards!
- -m- - -
- _-----
_-
-rl--
--
When using an electrical appliance, always follow
basic precautions, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
n
Warning.
Do not use outdoors or on wet surfaces.
Close supervision is necessary when any appliance is used by or near
children. Do not allow vacuum cleaner to be used as a toy or to run
unattended at any time.
Keep hair, loose clothing, fingers, feet and all parts of body away from
openings, rotating agitator and other moving parts.
cleaner in bare feet or when wearing open toe shoes or sandals.
Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes.
Do not use to pick up flammable or combustible liquids such as gasoline
or use in areas where they may be present.
The hose contains electrical wires. Do not use if damaged, cut, or
punctured.
Avoid picking up hard, sharp objects with the cleaner. They may
damage the cleaner and the bag.
Always turn off this appliance before connecting or disconnecting either
hose or motorized nozzle.
Do not use without dust bag or filters in place. Change bag frequently
when picking up very fine materials such as powder.
Use extra care when cleaning on stairs.
Do not put any object into openings. Do not use with any opening
blocked; keep free of dust, lint, hair, or anything that may reduce air flow.
Do not pull or carry by cord, use cord as a handle, close door on cord
or pull cord around sharp edges or corners. Do not run appliance over
cord. Keep cord away from heated surfaces.
$lzny;
Unplug cleaner when not in use. Turn off all controls before unplugging.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord. Never handle plug or appliance with wet hands.
The use of an extension cord is not recommended.
Do not use with damaged cord or plug. If appliance is not working
it should, has been dropped, damaged, left outdoors, or dropped into
water, take it to a Hoover Factory Service Center or Authorized Hoover
Warranty Service Dealer (Depot).
yse
nsbuctIons.
Company; others may cause hazards.
disconnect cord from electrical outlet before servicing the
.
vacuum cleaner
use
only
onlyattachrnents
To reduce the risk of fire, electric shock, or
injury:
Do not operate
as
for its intended use as described in the
recommendedbyTheHoover
Save these instructions!
2
Unpacking
Unpack cleaner from carton and
identify the parts shown. Remove and dispose of the cardboard packing.
A. Canister cleaner
B. Power nozzle
C. Paper bag
D. Extension wands and hose
The assembled cleaner will look
like the drawing below.
T
16
15-l
3
Cleaner description
1.
Cover:
forward.
2.
Carrying handle
remove by lifting up top section of carrying handle and pulling
Check bag indicator:
3.
for fullness.
4.
Extension wands:
when using cleaning tools, add one or both wands to hose.
5.
Spring latch:
or tool.
6.
Power nozzle:
7.
Dusting brush
a.
Crevice tool
9.
Tool rack:
dusting brush, and wall/floor brush.
10. Furniture nozzle
11. Wall/Floor brush
12. Large
carpet, area rugs and door sills.
13. ON-OFF control:
14. Cord clips:
wheels: provide easy towing, when cleaner is pulled over
locks extension wands together or locks wand to nozzle
automatically adjusts to different carpet pile heights.
provides tool storage for crevice tool, furniture nozzle and
fasten power nozzle cord to extension wands.
shows red when paper bag should be checked
use with power nozzle. If added length is desired
located on top of cleaner.
15. Receptacle:
16. Hand grip
17. Suction regulator:
difficult to push on some carpet or if lightweight rugs or draperies are
being cleaned.
16. Plastic latch ring:
cleaning tools.
Operate cleaner only at voltage specified on data plate on bottom of
cleaner.
This cleaner is intended for household use.
connect power nozzle cord underneath hand grip.
close for maximum suction; open if power nozzle is
rotate to lock hand grip to extension wands or
Questions or Concerns?
The
Hoover Company wants to quickly resolve any concerns about your
cleaner or questions regarding its use. Look on the list provided with the
product for your local
Pages under “Vacuum Cleaners - Household” for the nearest
Hoover Warranty Service Dealer
l-800-944-9200 for an automated referral of
authorized service outlet$-gations (U.S. only)
I-330-499-9499 to speak with a representative in the
Hoover Consumer Response Center.
DO NOT RETURN THIS PRODUCT TO THE STORE OR SEND IT TO
NORTH CANTON FOR SERVICE.
How to assemble
1.
Connect hose
insert hose end with cord into
opening of cleaner, lining up largest
projection on hose with largest
notch of opening. Turn hose to the
right to tighten.
Hoover Factory Service Center
(Depot) or call:
or in the Yellow
Authorized
When hose is attached properly,
hose cord plug will reach to
receptacle on cleaner.
Insert plug as deeply into the
receptacle as possible.
To disconnect hose, first remove
hose cord plug from receptacle.
Then, depress latch and turn hose
to the left.
2. Attach power nozzle
and extension wands
Attach wand to power nozzle by
fitting button projection on nozzle
connector into opening in spring
latch. Be sure nozzle is locked in
place.
To release, press down on center
of latch and remove nozzle.
5
Attach second wand to the first.
Position cord into cord clips on
wands, placing excess cord
between nozzle and bottom cord
clip.
To attach hose to wands, rotate
plastic latch ring on hand grip until
slots in opening align.
Push hand grip onto wand so that
button projection fits into slot. Turn
plastic latch ring to lock wand in
place.
Push plug on power nozzle cord
completely into receptacle underneath hand grip.
Always disconnect cleaner from
electrical outlet before attaching
or removing power nozzle plug.
Reverse this procedure to remove
wands.
6
How to use
To reduce the risk of electric shock, this appliance has a polarized plug
(one blade is wider than the other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.
Power nozzle
The power nozzle adjusts automatically for cleaning hard surface floors and
various heights of carpet. It is not recommended for very irregular surfaces
such as brick, slate, and certain parquet floors unless it is unplugged from
the cleaner. This will stop the agitator from rotating. If desired, the Wall/
Floor Brush (shown in Cleaning Tools section) can be used for this task.
Handle positions
The handle has two positions when
used with the power nozzle:
upright
and
operating.
To lower handle to operating
position, place your foot on the
power nozzle and push handle
back.
Edge cleaning
Brushed edge cleaning is provided
on both sides of the nozzle to
remove embedded dirt in carpet
near baseboards and furniture.
Guide side of nozzle parallel to
edge of carpet or furniture.
Suction regulator
The suction regulator is located on
the hand grip and is used to
increase or decrease suction for
various cleaning tasks.
If the power nozzle is difficult to
push on some carpet, open the
suction regulator. This will prevent
damage to the belt.
Cleaning tools
The cleaning tools have many uses.
Select the tool best suited for the
cleaning task from the descriptions
below.
Adjust the suction regulator to
select the amount of suction
appropriate for the cleaning task.
Select proper tool
1. Crevice tool
radiators, dresser drawers, spaces
between kitchen equipment.
2. Furniture nozzle
for upholstered furniture, draperies,
tapestries, mattresses, clothing,
automobile interiors and carpeted
stairs.
3. Dusting brush
carved furniture, table tops, books,
lamps, lighting fixtures, Venetian
blinds, baseboards, shutters and
registers.
4. Wall/floor brush
for walls and very irregular hard
surface floors such as brick and
slate.
may be used for
may be used
may be used for
may be used
Continued 3
8
To connect and
remove tools
To connect tools, insert end of tool
into extension wand and snap into
-.
position. To disconnect, press
down on the center of the spring
latch and remove tool.
Tools attach to hand grip by
rotating plastic ring until slots in the
opening align. Insert tool and turn
latch ring, as shown, to lock tool in
place.
To remove tool, reverse the above
procedure.
The power cord leading from hose
connection to receptacle on
cleaner base need not be con-
nected when using the cleaning
tools.
to cord, leave cord connected to
receptacle.
However, to avoid damage
To clean stairs
Clean stairs by placing cleaner on
end as pictured in the illustration.
Clean stairs from bottom to top.
9
How to store
Your cleaner can be stored on end
as shown in the illustration. Store
power nozzle with handle in
upright position.
The hose and extension wands can
be stored disassembled from the
cleaner if desired.
Maintenance
The following sections are concerned with proper maintenance of the
cleaner. Familiarize yourself with these home maintenance tasks and keep
this owner’s manual in a convenient place where you can refer to it when
needed. Proper use and care of your cleaner will ensure continued
cleaning effectiveness.
The bag
When
When the CHECK BAG indicator shows red, check the bag for fullness and
replace if necessary.
CAUTION: Very fine material such as face powder, cornstarch, fireplace
ashes or fireplace soot, may seal the paper bag and may cause it to
burst even though it is only partially full of dirt. When the cleaner is
used to remove material of this nature, the bag should be changed
frequently.
Where to buy
Bags may be purchased from your local Authorized Hoover Dealer (Depot)
or from a Hoover Factory Service Center.
to give the model number of your cleaner.
What to buy
For improved cleaning effectiveness, use
Filtration Type K
Regular
toreplace
disposable bags with your cleaner.
HOOVER Type K
bags also fit your cleaner.
When purchasing bags, be sure
Genuine HOOVER@ Micro
To assure that your HOOVER cleaner operates at
peak performance, it is imperative that you use
only genuine HOOVER paper bags distributed by
The Hoover Company. HOOVER bags can be
identified by the trademarks -
-
How to replace
Disconnect
1.
Remove cover by lifting top
section of carrying handle and
pulling forward.
cleaner from electrical outlet.
2. Depress latch and lift out used
bag.
3. Place lower notched edge of
new bag collar into grooves located
inside front of cleaner.
Note:
event, check the bag, making sure all folds are open.
some carpet surfaces can cause the nozzle to hug the carpet and also
restrict air flow. If this occurs, reduce the suction by opening the
suction regulator.
11
A bag that does not expand properly may restrict airflow. In this
4. Pull collar forward until latch
snaps into collar. Open folds of
bag. Push top of bag back.
Replace cover.
High suction on
Obstructions
Remove larger items from carpet and floor surfaces before vacuuming to
help prevent obstructions in hose, wands or nozzle connector, and to
maintain cleaning effectiveness of your cleaner.
There are two conditions that will indicate that an obstruction has occurred:
1.
Cleaner stops running (See
Thermal Protector
section.)
2. Cleaner continues to run, but suction is low. (See
section.)
Clearing obstructions
Thermal Protector
An internal thermal protector has been used in your cleaner to prevent
overheating if a large item or clog is caught in the nozzle or at the opening
of the bag.
will trip and the cleaner will stop running.
cleaner OFF and
hose from cleaner and remove obstruction from bag opening. If obstruction
is in nozzle, disconnect nozzle from wand and remove obstruction. After
3 minutes, the thermal protector will cool and automatically reset, then
cleaning may resume. If cleaner does not operate, allow additional time for
thermal protector to reset. The thermal protector may also trip if the bag
needs to be replaced. (See “The bag” section.)
When the blockage is not removed, the thermal protector
If this happens, turn the
disconnect cleaner from electrical outlet.
Disconnect
l-
Clearing obstructions
To check for obstructions, first turn
NOZZLE
cleaner off and
electrical outlet; then disconnect
power nozzle plug and wands
from hand grip.
turn on, and check hose end for
suction. Remove any obstructions.
Remove power nozzle from wands
and attach wands to hose. Check
for suction and remove any
obstructions.
power nozzle to wands, check
nozzle connector.
I
disconnect from
Plug cleaner in,
Before
attaching
Push nozzle connector down to
lowest position. Look into nozzle
connector and remove any
obstructions.
t
12
How to clean
Disconnect cleaner from eiectri-
cai outlet.
The secondary filter is located
inside the cleaner behind the paper
bag. To remove filter, first remove
cover of cleaner, then lift out filter.
Clean filter by rinsing it in water.
When dry, slide filter back into
position.
Do not operate cleaner without
the secondary fiiter in place.
The belt
The belt in your power nozzle drives the agitator. It has been designed
specifically for use in this cleaner and is important for effective operation.
What to buy
There are other belts manufactured that are similar in shape and size, but
may not be designed for the HOOVER power nozzle. Such belts may not
operate the agitator correctly and may create stress which could damage
your power nozzle. Use only a genuine HOOVER belt No.
a belt replacement is necessary.
38528-011 when
When to replace
The belt, located under the nozzle cover, should be checked from time to
time to be sure it is in good condition. To check, remove the nozzle cover
(see following section). Replace the belt if it is stretched, cut, or broken.
How to replace
Disconnect cleaner from eiectri-
cai outlet and disconnect power
nozzle from cleaner.
Turn nozzle over and unscrew the
4 recessed Phillips head screws.
Note: Do not remove the 3
screws in the triangle formation
as
these hold the motor in place.
1
13
1
MOTOR PULLEY
2. Return nozzle to original
position; and lift off nozzle cover.
3. If the belt is not broken, pull it off
the motor pulley.
4. Lift up end of agitator. Remove
old belt from agitator pulley and
replace with new belt.
5. Stretch belt back and attach to
motor pulley.
Hold opposite end of agitator in
place. Push belt end forward,
rotating end plate until it slides into
place. Turn agitator, making sure it
rotates freely.
14
6. Position nozzle cover on front lip
of nozzle base. Press cover into
place.
Turn nozzle over and replace
screws.
The agitator
When to replace
Disconnect cleaner
cai outlet.
When agitator brushes are worn,
the agitator should be replaced.
To check condition of brushes,
move the edge of a card across
agitator opening while turning
agitator. To maintain cleaning
effectiveness, replace agitator if
brushes do not touch card.
fern
eiectri-
How to replace
The agitator may be replaced with
either a single or double row of
brushes.
Single row of brushes - Hoover part
No.
48414-051.
Double row of brushes - Hoover
part No.
1. Remove nozzle cover, agitator
and belt following directions in
“How to replace belt”.
2. Discard old agitator .
3. Place new agitator as shown in
steps 4-6 of “How to replace belt”.
48414-049.
Lubrication
The motor is equipped with bearings, which have been lubricated for the life
of the motor. The addition of lubricant could cause damage.
Therefore, do
not add lubricant to either motor bearing.
The agitator is equipped with two ball bearings that should be lubricated
periodically by a Hoover Factory Service Center or an Authorized Warranty
Service Dealer (Depot).
If you have a problem
This appliance was inspected thoroughly and was in good operating
condition when it was shipped from the factory. If a minor problem occurs,
it usually can be solved quite easily when the cause is found. Therefore,
this check list is provided to assist you.
Problem
A. Cleaner
won’t run
B. Cleaner
suction
low
C. Agitator
won’t run
D. Nozzle
won’t
pick up
Possible cause
1. Not firmly plugged in.
2. No
3. Blown fuse/tripped breaker.
1. Bag full.
2. Obstruction In hose,
3. Secondary filter dirty.
4 Bag not opening.
5. Suction regulator control
6. Hose not properly
2. Broken or worn belt.
3. Nozzle sealed to carpet.
vottage
wands, or nozzle connector.
Improperly set.
netted
1. Hose power cord not
firmly plugged in.
1. Low cleaner suction.
2. Obstruction in nozzle
connector.
3. Agitator not running.
4. Agitator brushes worn.
in wall plug.
con-
to cleaner.
Possible solution
1. Plug unit in firmly.
2. Check fuse or breaker.
3. Replace fuse/reset
breaker.
1. Change paper bag.
2. Remove foreign object.
3. Clean filter.
4. Open bag by pulling
folds.
5. Adjust suction regulator.
6. Reconnect hose.
1. Plug
2. Replace belt.
3. Open suction regulator.
1. See Item B.
2. Remove foreign object.
3. See Item C.
4. Replace brushes.
firmty
into receptacle
on cleaner base and
underneath hand grip.
16
Service
To obtain approved HOOVER service and genuine HOOVER parts,
locate the nearest Hoover Factory Service Center or Authorized
Hoover Warranty Service Dealer (Depot)
0
checking the Yellow Pages under “Vacuum Cleaners
Household” OR
0
checking the list of Factory Service Centers provided
with this cleaner OR
0
calling I-800-944-9200 for an automated referral of
-
-
authorized service outlet locations (U.S. only)
Do not send your cleaner to The Hoover Company in North Canton
for service, this will only result in delay.
If further assistance is needed, contact The Hoover Company
Consumer Response Center, North Canton, Ohio 44720
Phone: 330-499-9499.
in
Canada, contact Hoover Canada, Burlington, Ontario
Phone: I-800-263-6376.
by:
L7R
4A8,
-
Always identify your cleaner by the complete model number when
requesting information or ordering parts. (The model number
appears on the bottom of the cleaner.)
Cleaning Effectiveness Per Amp Rating
This is not an Amp rating. Amps do not measure dirt removal, only the
amount of electricity used. Cleaning Effectiveness Per Amp is determined
by dividing this model’s Cleaning Effectiveness* by its Amps.
*Cleaning Effectiveness
(a)
the geometric mean of the amount of embedded carpet dirt removed in
testing under ASTM Test Method
(b)
the value 2.9 (the geometric mean of the midpoints of the % dirt pickup
scales selected by Hoover as a reference for its rating system).
is the percent value obtained from dividing:
F608-89,
by
17
1/,
V#
HOOVER and
THE HOOVER COMPANY,
0
are registered trademarks
NOFiiH
CANTON, OHIO 44720
R4 4-96
S3395040/9 I
Litho USA
56513-331
Loading...