Honeywell VDC-350PIV-V User Manual

NIGHT VISION IR DOME CAMERA

Model VDC-350PI V-V VDC-35 0NIV-V

Image Sensor

Signal Syste m PAL NTSC

Effective Pixe ls 752(H)x582(V) 768(H)x49 4(V)

Resolution

Minimum Ill umination

Shutter Speed 1/50-1/100,000SEC 1/60-1/1 00,000SEC

S/N Ratio

White Ba lance

AGC/BLC

Gamma C orrection

Sync Model

Lens

IR LED

IR Beam Distance

More Than 5 0dB

1/3'' SUPE R HAD II C CD

0.1Lux/F1.2(IR L ED OFF), 0Lux (IR LED On )

540TV Lin es(Color), 600TV L ines(B/W )

Automati c

Automati c

0.45

INT

Varifoca l lens, f=4-9mm

Wave Le ngth 850nm , x 21pcs IR L ED

10~15m

IR LED Driv e

Video output

Power Input

Power Consumpt ion

Operating T emperature

Body

Weight

On: 1~3Lux; Off: 5~6Lux

1.0Vp-p, 75Omh, Sync Negative Po larity

1000g

DC12V Re gulated

150mA (IR LED OFF)+15 0mA(IR LED O N)

-10℃ ～ +5 0℃, RH90% MAX (non-c ondensing)

Alum inum

VDC-350PIV-V
VDC-350NIV-V

User Guide

1. Features

The camera adopts advanced Digital Signal
Processor(DSP) technology,Enhances picture
quality greatly to horizontal resolution of

540TVL. Provides clearer and more vivid image.

Latest DSP controls for BLC, white balance,
and gain control.

Integrated efficient powerful IR LED array can
capture high-resolution picture even in complete
darkness. Night view distance up to10~15m.

Light control design. Auto light detection for IR
LED switch control.

The camera is equipped with a Vari-focal lens,
f=4~9mm.

Manual pan /tilt mechanism,3-Axis Rotation.

Accept 12VDC power supply.

Anda polygon dome shield, which can bear up to
120 pounds impact and won't be destroyed. It
has excellent sealing performance and can also
be installed by outdoor .

Polygon material made dome shield possesses

high light permeate rate, strong shock resistance
capability. The whole Aluminum base can stand
lasting shock and high temperature.

NIGHT VISION IR DOME CAMERA

2. Safety Precautions

The installation should be made by qualified service
personnel or system installers and should confirm
to all local codes.

1.Power supply

(1) use with a 12VDC regulated power supply
(2) To prevent fire or electrical shock, UL listed class
2 wiring should be used for the 12VDC input terminal.
(3) Be used to connect each lead to the appropriate
terminal. Wrong connection may cause malfunction
and/or damage to the video camera.

2.Operating and storage locations

(1).Do not attempt to point the camera at the sun or
other extremely bright objects that cause smear to

appear no matter the camera is power on or not.
It leads to damage of the CCD(Charge Coupled

Device).
(2).When camera is installed next to equipment,

such as wireless communication device, it emits a
strong electromagnetic field, some irregularity such

as noise on the monitor screen may happen.
(3).Be sure to use a ceiling board having enough
strength to support this camera.
(4).Assemble the camera's main parts and lens
quickly in a sanitary place.
(5).Do not pull the cable, it may cause disconnection.
(6).Do not touch the inside of camera even if
something is wrong.
(7).Before installation, make sure to disconnect the

power supply first, check the ground connection,
and then install it.

(8).Operating temperature range:-10℃~+50℃,(14°F~122°F);
Storage temperature range:-20℃~+60℃,(-4°F~140°F).

(9). Be sure to use proper screws which cameras can
be beared on the material firmly.

1

NIGHT VISION IR DOME CAMERA

2

3. Handling of the Unit

(1) Never attempt to disassemble or modify the camera.

(2) If an abnormality should occur, immediately turn off
the power and consult your dealer.

4. Parts Description

Front View

Dome cover (transparent)

IR-LED

Body cover

Camera base

Mounting Holes

Wire hole

BOTTOM View

Camera body

5. Cover Removal and Attachment

To remove the body cover and camera body,
disassemble it with the L WRENCH provided in your
ACCESSORY set. (Rotating clockwise will close it
and rotating anti-clockwise will release it.)

Acecessories

1. PLASTIC
ANCHOR

2. ASSY SCREW
TAPPING

NIGHT VISION IR DOME CAMERA

3. L WRENCH

3

1.PLASTIC ANCHOR: insert into the SCREW hole of the
installation location(to strengthen the installation).

2.ASSY SCREW TAPPING：use for installation on the
ceiling or wall.

3. L WRENCH：for body cover and camera base
assembly.

6. Installation

1.Drill a hole in the place where the camera is
installed. Completely insert the PLASTIC ANCHOR
provided. then lead the power and video cables pass
through the hole.

2.Disassemble the body cover and camera base
from dome camera .

3.Fasten the dome camera base on the wall or the
ceiling.

Ceiling

NIGHT VISION IR DOME CAMERA

Wall

4. Adjusting the Camera Direction

Camera body moves in three ways: pan, tilt and rotate.
Adjust the direction so that the lens is pointing at the
target.

5. Use the lever to adjust the view angle and focus.

Rotate 180°

Pan360°

6 urn the dome cover to adjust until the lens point at T

.

the window, screw tightly and complete the installation.

7. Connecting Low Voltage Power & Video Signal
The wiring harness have a BNC connector to accept
video signal ,the other connectors to accept the low
voltage power. For mounting directly to a wall or ceiling,
run power and video lines to the target location.

4

Tilt 90°

View angle
adjustment lever

Close

VIDEO

12VDC

NIGHT VISION IR DOME CAMERA

Focus
adjustment lever

5

7. Self-Check Points
Before Consulting After-Sales Services

CONDITIONS

Screen
not turned on

Screen not clear
or is spread

CHECKING POINTS

*Make sure whether power is connected correctly.
*Check if the cable is connected correctly.

*If dust is seen through the monitor screen after
fixing lens, dissemble the lens and clear off the
dust on the surface of CCD withblower or soft cloth.

8. Specifications

NIGHT VISION IR DOME CAMERA

All data and specifications subject to change
without notice.

9. Type Number Overview

Model(12VDC)

Signal system

10. Dimension Outline

6

VDC-350PIV-V
PAL

IR NIGHT VISION DOME CAMERA

146mm

NIGHT VISION IR DOME CAMERA

VDC-350NIV-V

NTSC

6

7