Honeywell VCC-600N-P User Manual

Operation Manual OSD Color Camera

VCC--

VCC

※ Thank you for choosing Honeywell VCC-600N/P camera.

Please read these instructions carefully before operating this unit, and retain this manual for future reference. If you have any problems with this camera, contact your local supplier to service.

600N/P

CAUTION for SAFETY OPERATION

1. Water and Moisture

To prevent fire or shock hazard, do not expose this camera

to rain or moisture.

2. Servicing

Do not attempt to disassemble or repair by yourself. You may be exposed to dangerous voltage or other hazards. Note that all servicing is qualified service personnel. Modifications not approved by manufacturer could void the user's authority to operate the equipment.

3. Power Sources

To prevent electric shocks and risk of hazards, do NOT use more than the specified power source.

4. Environment

Do not install too warm or too cold place. Recommended operation temperature is between -5℃ and 50℃

5. Sunlight

Do not point the camera at the sun. CCD can be damaged.

6. Heavy Shock and Vibration

Do not drop the camera or subject it to heavy shock of vibration.

7. Install on an Unstable Place

Do not place or install this camera on an unstable place, stand, tripod, bracket or table. That may cause serious injury to people or damage to appliance.

8. When operation is incorrect or a malfunction is observed

While operating, if any abnormal condition (strange sound, smell or smoke) or a malfunction (no pictures, etc.) is observed, stop using the camera immediately, turn the power off, then contact your supplier.

9. Cleaning

Turn the power off and wipe off the dirt with a dry soft cloth. If it is extremely dirty, use furniture cleaner to wipe it off. To clean the lens, use a blower or lens cleaning tissue. (available from any camera dealer)

10. Do not shoot any source of bright light.

If the objects contain very bright areas, bright vertical or horizontal lines may appear on the screen. This is called "smear" , a Phenomenon which often occurs with solid

- state pickups, and is not a malfunction.

11. Damage Requiring service

Unplug the camera from the power source and refer servicing to qualified service personnel under the following condition: A. If the power-supply cord or plug is damaged. B. If the camera has been exposed to rain or water. C. If liquid has been spilled, or objects have fallen into the camera. D. If the camera does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a

qualified technician to restore the camera to its normal operation. E. If the camera has been dropped or the cabinet has been damaged. F . If the camera exhibits a distinct change in performance. G. Warranty is not covered in case of natural disaster or wrong

Installation.

INSTRALLATION

Mounting a lens

1. Remove the Protective cap in front of the camera.

2. Confirm the mount ring whether it is for C or CS.

3. Attach the lens to the lens mount ring.

4. If the lens has an Auto Iris mechanism, connect the iris cable to the LENS in rear of the camera.

① In the case of having no iris amplifier : Set the slide switch to

DC (Down side).

② In the case of having iris amplifier : Set the slide switch VSD

(Upper side) ※ When connecting Auto iris lens, be sure to use the connector to

be recommended by manufacturer.( E4-191, ChuoMusen, Japan)

VSD LENS PIN CONFIGURATION

1. Power(12V) 2. No Connection

3. Video Signal 4. GND

Back focus adjustment

1. In case of fixed focus lens

① Loosen the locking ring with L type wrench and set the focus ring

of lens to infinity ( ∞ ).

② Tune the mount ring to get a clear picture( distance from camera

to object is more than 23m) and fasten the locking ring.

2. In case of zoom lens

① Loosen the locking ring with L type wrench and set the lens to the

maximum telephoto position. Then turn the focus ring to focus. ※ In the case of Auto iris lens only, shoot a comparatively dark

object or reduce the ambient light so that the aperture is fully open.

② Set the lens to its maximum wide angle position, and set the focus. ③ Repeat step ① and ②, until the difference between focusing

position ① and ② is smallest.

④ When the best focusing point in found, fasten the locking ring.

Connection of power supply

Must be checked the power source from the external power supply before power on.

①③

④②

DC IRIS LENS PIN CONFIGURATION

1. Control - 2. Control +

3. Drive + 4. Drive -

①③

④②

The contents of the package Check the below contents

- VCC-600N/P Camera 1set

- Auto Iris Lens Plug

- L Type Wrench

- Operation Manual (English)

TROUBLESHOOTING

Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center.

In case of no image

Is the coaxial cable attached securely? Are the power and voltage normal? Has the iris of the lens inside the camera been adjusted correctly?

In case of unclear image Is the lens in focus? Is the lens dirty? Is the monitor adjusted correctly? ※ Dirt of fingerprints on the lens can adversely affect the

images. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available).

DIMENSIONS

Unit: mm

ENTER

POWER

DC12V

DC VSD

NAMES & FUNCTIONS OSD MENU

GENERAL SETUP

UP BUTTON

ENTER BUTTON

(-) BUTTON

ENTER

CONT

POWER

DC12V

DC VSD

POWER ON LED

This LED is ON in power ON state.

LENS

VIDEO

CONT

Power Input Terminal and MD Alarm Output

DOWN BUTTON

(+) BUTTON

LENS CONNECTOR

LENS

VIDEO

VIDEO OUTPUT

Composite Video Signal Output

Lens Type Select Switch

DC Lens: with no iris amp. VSD Lens: with iris amp.

SYNC SYNC LEVEL adjustment (01…255) BURST BURST LEVEL adjustment (01…255) CONTRAST CONTRAST LEVEL adjustment

(01…100)

RETURN Return to the previous menu.

CAMERA SETUP

AE MODE LENS MODE, SHUTTER, AGC, BR IGHTNESS, MAX AGC,

WB MODE AWC LOCK, AWC AUTO, ATW, INDOOR, OUTDOOR,

BLC MODE OFF, BLC, WDR, BMB and

their level, area setting. PZM SET Privacy Zone Masking function setting. NIGHTSHOT Day  Night, Night  Day mode setting. CAMERA ID Camera ID and Position setting. RETURN Return to the previous menu.

MEM FUNC. SETUP

DNR MODE Digital Noise Reduction mode

setting. (OFFLOWHIGH) PIP MODE Picture-in-picture mode setting. QUAD MODE Quad display mode setting. MD MODE Motion Detection mode setting. D.ZOOM Digital Zoom setting. (OFF1.0x…16.0x) MIRROR Mirror mo de setting. (OFFH.MIRRORV.MIRRORFLIP) RETURN Return to the previous menu.

SPECIAL SETUP

SHARPNESS Sharpness compensation setting. (0~15) GAMMA Gamma compensation setting. (0.36~1/USER , 8steps) LANGUAGE OSD Language setting. (ENG , KOR, JPN, CHI1, CHI2) RETURN Return to the previous menu.

DEFAULT SETUP

FACTORY DEFAULT Set to the Factory Default. RETURN Return to the previous menu.

EXIT SETUP

SAVE AND EXIT EXIT RETURN Return to the previous menu.

MAX FIELDS, etc.

MANUAL, etc.

SPECIFICATIONS

Operational

Image Sensor

Total Pixel

Effective Pixel

Scanning System

Scanning Frequency

Sync System

S/N Ratio

Min. illumination

Horizontal Resolution

Video Output

Lens Iris Control

Electronic Shutter

AGC

Back Light Compensation

White Balance

Electrical

Rated Voltage

Power Consumption

Mechanical & Environmental

Lens Mount

Weight

Dimensions

Front & Rear Color

Body Color

Operating Temp.

Storage Temp.

Operating Hum idity

Honeywell Security Group Honeywell Co., Ltd. Address: 5F, Sangam IT Tower, B4 - 4block, 1590 Sangam-dong, Mapo-gu, Seoul 121-835, Republic of Korea TEL: +82 2 799 6020 / 6395 / 6006 FAX: +82 2 792 9011 E-mail: info.security@honeywell.com

VCC-600N VCC-600PMODEL NAME

NTSC PALVideo Standard

SONY 1/3” Super HAD CCD

410,000 Pixels 470,000 Pixel s

380,000 Pixels 440,000 Pixel s

525 Lines, 2:1 Interlace 625 Lines, 2:1 Interlace

15.734kHz(H), 59.94Hz(V) 15.625kHz(H), 50Hz(V)

0.1lx (F=1.2, 50IRE)

0.001lx (F=1.2, 50IRE, MAX FIELDS x512)

1/60 ~ 1/100,000 sec 1/50 ~ 1/100,000 sec

AWC LOCK / AWC AUTO / ATW / INDOOR / OUTDOOR / MANUAL

More than 50dB

VBS 1.0Vp-p / BNC

MANUAL / DC / VSD

OFF / BLC / WDR / BMB

61.6[W] x 52.4[H] x 77.8[D]mm

Pantone Color 11C (Gray)

-10°C ~ +50°C

-20°C ~ +70°C

90% RH (non-condensing)

INTERNAL

540 TV Lines

OFF - 36dB

DC12V ± 2V

1.5W (max)

CS Mount

181g

Gray

Printed in Korea

D-100073-001, REV.0