Honeywell V4043C PRODUCT DATA

Design

V4043C zone valves consist of:

• 2-way valve housing with BSPP internal threads

• Control ball assembly

• Actuator assembly with cable

Materials

• Valve housing made of forged brass

• Spindle shaft made of brass

• O-ring seals made of EPDM rubber

• Ball plug made of NBR rubber

• Actuator cover and base made of zinc-plated steel

V4043C

Motorized Zone Valves

2-PORT HYDRONIC VALVES

PRODUCT DATA

Application

Honeywell V4043C 2-port hydronic valves are used in domestic and small commercial heating and cooling applications to control the flow of hot or cold water.

They are designed for on-off zone control of domestic systems and can be used to control individual fan coil, radiator, space heater or convector applications. They can be controlled by a line voltage SPST controller such as a room thermostat, aquastat or flow switch.

The actuator head is removable without affecting the integrity of the water system.

Features

• Rugged design

• Control by a line voltage SPST controller

• Minimal actuator power consumption

• Actuator head installation does not require draining of

the system

• High flow rate capacity

• Indifferent to dirt in system

Specifications

Medium Water or water-glycol mixture

pH-value 8...9.5

Operating temperature 5...88°C (41...190°F)

Ambient temperature max. 50°C (122°F)

Operating pressure max. 8.6 bar (125 psi) static

Differential pressure see chapter “Dimensions” below

vs (cv)-values see chapter “Dimensions” below

Flow A – B

Starting position normally closed

Voltage 220-240V, 50Hz

Power consumption 6W / 0.042A

Nominal timing On: 12 seconds under power

Electrical termination 1m flying lead, heat resistant

Shipping temperature -40…65°C (-40…149°F)

Humidity rating 5…95% RH (non-condensing)

Atmosphere non-corrosive, non-explosive

(max. 50% glycol content), quality to VDI 2035

Off: 6 seconds under spring return

cable

V4043C

Function

V4043C 2-position normally closed hydronic valves are used in domestic and small commercial applications to control the flow of hot water. They consist of an actuator and a valve.

With the manual opener set to AUTO and the actuator energized, the valve is opened. When the actuator is deenergized, a spring-return mechanism drives the valve to the closed position. The valve can also be opened with no electrical power by moving the manual opening lever over the stop and pushing slowly and firmly to the MAN. OPEN position. The stop permits the valve to be locked in the open position. The valve returns to the automatic position when the valve is energized.

Wiring

Fig. 3. Wiring diagram for V4043C

Dimensions and Ordering Information

A power failure will leave the valve at the spring-returned position. When power is restored, the valve will respond to controller demand.

Fig. 1. V4043C in closed

position

Fig. 2. V4043C in open

position

Wire Function

a = brown line (power supply)

b = blue neutral

c = green/yellow earth (ground)

Fig. 4. V4043C 2-way zone valve

Table 1. Dimensions and Ordering Information

off pressure

Dimensions Body kvs-value max. close-

A B C D

OS-No.

1/2” BSPP (internal) 3.0 1.38 bar 87 98 60 96 V4043C1255

3/4” BSPP (internal) 6.9 0.55 bar 87 98 60 96 V4043C1263

1” BSPP (internal) 8.6 0.45 bar 87 98 60 96 V4043C1271

NOTE: All dimensions in mm unless stated otherwise

ACS Control Products

Honeywell GmbH

Hardhofweg

74821 Mosbach, Germany

Phone: +49 (6261) 810

Fax: +49 (6261) 81393

www.honeywell.com

EN0H-0324GE25 R0906 September 2006 © 2006 Honeywell International Inc. Subject to change • All rights reserved Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 37, Switzerland or by its Authorized Representative.