Honeywell TCC800M, TCC8M Quick Start Manual

control panel version,

Arm buttons.

buttons 1 and 3. To register the keyfob with

Keyfob TCC800M, TCC8M

This keyfob can be used with all Domonial
panels from version I onwards, radio
modules CO79, CO79-2 and 5882EUHS
supporting the Alpha protocol and on older
panels that support the V2 protocol (HF
keyfob models). In the latter case, the TCC
keyfob simulates a TC805HF keyfob.

Battery Specification

It is recommended that only the following 3V
battery is used: CR2032 by Panasonic or GP.

LED

LED

LED

B1 B2

B1 B2

B1 B2

B4 B3

B4 B3

B4

- Button 1: Arm
Total Set

- Button 2: Disarm

- Button 3: Arm
Partial Set

- Button 4: System
Status

B3

- SOS: Buttons
1 and 3 send an
immediate alert
when depressed
simultaneously for
2 seconds.

TCC Base and Belt Hook
To fix the TCC to a wall, unclip it from its
base and screw the base to the wall, using
the two screw holes (screws not supplied).
To fix it to a belt, slide the belt hook upwards
into the slot provided in the base of the TCC.

Registration and Configuration

1. First, set the panel to registration mode.

2. To register the TCC keyfob, press

a different panel, remove and replace the
battery before registering as usual.
Configuration is performed with
a programming tool. Total, Annex or
Total + Annex.

Changing the Battery / Protocol

1. To change the battery, remove
the TCC keyfob from its base and
unscrew the battery compartment with
a screwdriver.

2. The default protocol
is Alpha, but
depending on the

you may need to

3. To change to V2: While inserting the
new battery, press the Disarm and Part

4. To change to Alpha: While inserting
the battery, press the Total Arm and
Disarm buttons.

The LED related to buttons B1 and
B2 pushed will light for 3 seconds then
after they will light off and if

Alpha: LED of B1 and B2 flash for 8s
V2: LED of B1 and B2 flash for 3s.

The new protocol is retained in memory,
and is not affected by the user changing
the battery.

change this to V2.

www.honeywell.com/security/emea/hscdownload

Identification Rings

You can choose some coloured rings
to help you identify your keyfob.

Recommendations

Risk of fire, explosion and burns if
the battery is not replaced correctly.
Dispose of used batteries according
to the manufacturer's instructions and
in compliance with local laws and
regulations. In Switzerland, annex 2.15
of SR 814.81 is applicable to used
batteries in this product.

Characteristics

- Dimensions: 56mm x 49mm x12mm

- Weight:

Without packaging: 25g
With packaging: 34g

- Batteries: 3V CR2032

- Battery life (in years):

Alpha: 1.6
V2: 2.7

- Temperature:

Operation: -10°C to +55°C
Storage: -20°C to +70°C

- Humidity:

Operation and storage: 5% to 95%
(without condensation)

- Radio:

Range (open field): 500 m
Frequency: 868 MHz

- Consumption:

Sleep mode: 2µA
Active mode: 30mA

NF&A2P 2 shields
IP32-IK04
NF324, H58
Tested and certified according to the
EN 50131-1 and EN 50131-3 standards,
grade 2, environmental categor y II.

Certifying bodies: www.cnpp.com and

www.marque-nf.com

Honeywell Security Group - 1198 Avenue du Docteur Maurice Donat BP 1219 06254 Mougins Cedex:
Tel: [phone] Fax: [phone] © Honeywell International Inc.
Certification: To obtain applicable CE compliance Declaration of Conformity, please refer to our web site: