Page 1
This wireless passive infrared motion sensor is intended for use with Honeywell controls that support
Mounting Location
Mounting Options
[A]
[B]
Note
PRELIMINARY DRAFT IIs – 01/12/15
SiX™ series devices.
• The optimal range is
obtained at a mountin
h
eight of 7’ 6” (2.3 m)
• A
llow a clear line-of-sight
to all areas to protect.
• Do not directly face
windows.
• Avoid close proximity to
m
oving machinery,
fluorescent lights, an
h
eating/cooling sources.
g
.
d
• For use in applications
with pets up to 80
pounds (36 kilograms).
The RF6PIR can be
mounted on the wall or in
corners:
•
•
• The rear tamper plate
• UL requirements: TBD
RF6PIR permanently,
conduct Go/No Go tests
(see control’s instructions)
to verify adequate signal
strength and adjust the
device location and
orientation as necessary.
= Wall mounting
oles.
h
= Corner mounting
oles.
h
MUST be mounted to
stud, solid wood, or with
a robust wall anchor.
: before mounting the
a
Page 2
Enroll the RF6PIR
The RF6PIR can be enrolled and
programmed before or after installation.
Note
Programming RF6PIR Services
Walk Test the RF6PIR
Note
disarmed
• Press down on the top latch and separate
the front and back covers.
• Set the Lyric Smart Controller in
Programming Mode.
• Remove the RF6PIR battery tab to
activate and begin the enrollment process.
• The green LED beneath the battery flashes
during enrollment (about 8 seconds) and
the control beeps (TBD).
• The device sends the device MAC ID
address and Services information to the
control. The control registers the device
and displays the transmitter data on
screen.
• Enrollment is confirmed when the RF6PIR
LED is ON for 3 seconds [and the control
beeps TBD].
• If the sensor is not successfully enrolled
during the enrollment period, the LED
turns off and the device powers down.
Activate a tamper to restart the enrollment
process.
: Once enrolled in a system, the sensor
cannot be used with another control panel until
it is removed from the current control panel. See
the Control’s instructions for details on
removing devices.
Fault device features to “Learn” device
“Services” in the control:
- Cover and Wall tamper switches
- Selectable Pet Immunity –
Off or up to 80 lbs (36 kg)
- Temperature sensor; accuracy ±3°F
Consult the Lyric Smart Controller’s
instructions for programming the device in
the system.
After power up and enrollment, activate the
Test Mode with the control (see control’s
instructions) or use the Flashlight Feature.
Test period.
: the system must be in
the 10 minute Test mode to begin.
Walk through the detection area and observe
the LED.
Test Mode is active for 10 minutes, then
automatically exits test mode, disables the
LED and enters normal operation mode.
To restart the 10 minute Test Mode, use the
flashlight feature (see the following section).
mode for
Page 3
Flashlight Feature
This feature is no longer
available after the first system arming
Detection Patterns
Battery Replacement
BATTERY CAUTION:
Specifications
Power - Battery:
Battery Life, years (typical):
Range:
Wall Mounting Height:
Tampers:
Operating Temperature:
Relative Humidity:
Temperature Compensation:
Dimensions:
Weight:
Approval Listings
at least
once each year
Zones
A
18
B
46
C
36
Note: the flashlight feature only initiates
change any other sensor settings.
The flashlight feature is initially only available for the
first 24 hours after the first power up, or until the
system is first armed.
.
Each time the flashlight features is used, and the system
is disarmed, the walk test timer restarts for 10 minutes.
1. Use a flashlight with a bright light beam, and stand
within 4’ (1.2 m) of the sensor.
2. Swing the light beam past the sensor Lens 3-5 times,
holding the beam on the window for 0.5 second each
pass.
or restarts the Test Mode and does not
Lower
Intermediate
Long
• Remove the front cover.
• Replace the battery.
Recommended replacement batteries:
Panasonic CR123A
Honeywell 466
Duracell DL123 or DL123A
• Replace the front cover.
Do not recharge, disassemble, heat above 212° F (100°
C) or incinerate. Dispose of used batteries promptly.
Keep away from children.
Risk of fire, explosion and burns.
123A, Honywell 466
40’ x 56’ / 12 m x 17 m
Cover and Wall; (reported separately to the panel)
x oz / xx g (net weight)
One 3V, Lithium; Panasonic CR123A, Duracell DL 123 or DL
4 years
4.13” H x 2.38” W x 1.61” D / 105 mm H x 60.4 mm W x 41 mm D
7’ – 9’ (2.1 m – 2.7 m); Optimal 7’6” (2.3 m)
32° to 122° F / 0° to 50° C
5 to 95%; non-condensing
Advanced Dual Slope
FCC / IC
SIA-PIR-01
ETL
UL 639
ULC S306-03
RoHS
The product must be tested
.
Page 4
DOC CODE 128B BAR CODE HERE
P/N 800-19202PIR 01/15 Rev BETA
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized
changes or modifications could void the user's authority to operate the equipment.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes:
(1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une
reception indésirable.
RF Exposure
Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must
not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au moins 7,8 pouces
(20 cm) de toutes les personnes
.
Support and Warranty
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF
THE ENTIRE ALARM SYSTEM.
For the latest U.S. warranty information, please go to www.honeywell.com/security/hsc/resources/wa or
Please contact your local authorized Honeywell representative for product warranty information.
2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved.
www.honeywell.com/security
Loading...