INSTRUCTION MANUAL
COLOR VANDAL PROOF CAMERA
HVD-735NT/PT
HVD-735NW/PW
HVD-505N/P
About this manaul
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
This instruction manual covers for use in the following models. Any
difference among the those models is indicated when necessary.
PRECAUTIONS
■ Do not open or modify
Do not open the cabinet exet during maintenance and
installation, as it may be dangerous and cause damages.
■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get insdie the camera. It could cause fire, short-circuits or
damages.
■ Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■ Install away from electric or magnetic fields
■ Protect from humidity and dust
Dimensions : mm
Honeywell
DC12V or AC24V
TROUBLESHOOTING
Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.
■ If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■ Protech from high temperature
Be careful when installing colose to the ceiling , in a
kitchen
or boiler room, as the temperature may raise to high
levels.
■ Cleaning
Dirt can be removed from the cabinet only by wiping it
with a soft cloth moistened with a soft detergent solution.
■ Mounting Surface
The mounting surface material must be strong enough
to secure the camera.
SPECIFICATION
■ If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt of fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RIST OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
S
W
T
CONNECTIONS AND CAMERA SETTINGS
ON
■ CONNECTIONS ■ LENS ADJUSTMENT
DC12V
AC24V
Black (-)
Focus
Red (+)
60˚
60˚
Zoom
Focus
360˚
CAUTION
Check for polarity when using a DC 12V or AC 24V power supply.
1. Adjust the panning(360˚) and tilt(60˚) position.
2. Setting the zoom position by using Zoom Lever Screw.
3. Setting the focus by using Focus Lever Screw.
■ CAMERA SETTINGS for HVD-735NW/P
OFF
ON
■ CAMERA SETTINGS for HVD-505N/P & HVD-735NT/P
HVD-505N/P HVD-735NT/PT (Upper board & Rear board)
(10
(3)
(1)
(2)
OFF ON
1324
(7)
(7)
(6)
White balance
lock button
(1)
ON
162345 78
This switch is
not used.
(2)
(3)
360˚
(4)
(5)
(8) (9
ON
ON
OFF
12
OFF
ON
● Correcting Flicker (1)
Correct screen flickering athat occurs when positioned under
fluorescent lights that use a 50 Hz power supply frequency.
ON Under 50 Hz fluorescent lights
OFF Normal setting
● Confirming the iris setting (3)
ON The default setting when DC auto-iris lens is installed
OFF The default seeting when fixed iris lens is installed
CAUTION : The iris setting is preadjusted as the best condition for
use at time of factory shipment, so it isn't necessary to change settings
● Compensating for backlight (2) ● Setting gain control (AGC) (4) - HVD-735NT/PT
ON When back light is so bright For adjusting the sensitivity of the camera. Use this setting for shooting
OFF Normal setting
CAUTION : It will be correctly set by adjusting level volume 7.
in dark environments.
ON Normal setting
OFF Set this when there is excessive noise
Loading...