To program VCR, see over.
HTR1 Kit Quick Start Guide
1 Installing the HTR1
Note Make sure you have everything you need before you
begin the installation.
1. Choose a location and mounting option that provides convenient
access for installing and removing the VCR tape. Ensure that the
location you choose conforms with local regulatory guidelines.
Note Do not mount the VCR enclosure on the floor if bus is
washed out with a hose.
2. Mount the VCR enclosure base to mounting surface.
Note Illustration shows an inverted mount.
Console
Possible mounting options:
• Horizontal (upright or
inverted)
Underneath
bulkhead
Glove box
(inside or
underneath)
Beside
driver seat
Under side of
passenger seat
n Unlock access panel in
front of VCR cover.
o Remove cover.
p Use VCR
enclosure base to
mark and drill holes.
q Secure base with fou r
#10 x 3/4 in. sheet
metal mounting screws.
VCR
p
3. Connect the wiring harness to the electrical system.
4. Complete installation.
Note Illustration shows an upright mount.
Signal harness
Red wire
Black wire
White wire
Brown wire
Black wire
Green wire
Red wire
Blue wire
Battery (POS - 3A fuse)
Battery (NEG)
Ignition
Input signal 1 BRK
Input signal 2 STP
Input signal 3 TRN
Input signal 4 FSH
Input signal 5 ARM
Power harness
20 ft. (6.1 m) cables
VCR wiring harness
DB25 connector
Camera 1
Audio in
Video in
Power
Camera 2 (Stop Arm)
Video in
Power
Camera 2 (Stop Arm)
Optional external
microphone (call to
order)
VCR rear panel
n Secure the VCR in the VCR
enclosure base with the
velcro retaining strap.
o Slide enclosure cover
inside side rails of enclosure
base.
p Replace access panel and
lock it to secure the cover to
the base.
o
p
HTR1 Quick Start Guide
Document 800-00760 Rev A 11/07
© 2007 Honeywell International Inc.
Video Systems
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be
accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to
change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Specifications subject to change without
notice. Imperial conversions are approximate.
2 Programming the VCR
1. Install the two AAA/UM4 (size E92) batteries (supplied) into the
remote control.
2. Remove or open access panel on enclosure cover.
3. Plug RCA cable into VIDEO OUT jack on front of VCR. Plug other
end into VIDEO IN jack of a portable monitor.
Start vehicle. Press MENU on the remote control to enter the Program
mode. To apply temporary power to program the VCR without turning
the bus ignition on, use the VCR POWER button.
User configurable settings
You can change any of the pre-configured factory settings shown
below.
Turns unit off
Program mode
S
T
Play mode
Ejects VCR tape
Video tracking
Rewind tape/search images
Playback video
Playback images fast forward
Pause
ST
WW
X
XX
Move cursor left
Move cursor right
Enter/exit Program mode
TRK
TRK
Change value
Select action
Display or exit Menu
UP/DOWN
ENTER
MENU
Playback or Record mode
Change Rec and Play
REC/PLAY
HOURS
Stop playback or recording
Record video
and character
speeds (EP or SP)
Text line (up to 20 characters)
Reset/restore defaults
Record speed
5 Trigger
4 Daily
Recording mode
Record stop delay (0-54 mins)
Current time, date
= Feature is enabled
= Parameter is disabled
For example, Bus ID
DST = Daylight Saving Time on/off
and DST indicator
indicators
Selected trigger is active
Selected trigger is inactive
timers
XXXXXXXXXXXXXXXXXXX
10:09:07 DT 1/ 7/2008
BRK STP TRN
FSH ARM 00 00 EP
MPH
12:00 12:00
12:00 12:00
12:00 12:00
12:00 12:00
Speed in MPH or KPH
GPS direction
GPS latitude/longitude
Start Delay (0-60 mins)
Bus ID on/off
Bus ID String
4. Press MENU to exit Program mode, then POWER on front of VCR
to start recording.
3 Daily operation
Legend: Status Indicators Daily Timers
= Parameter is enabled
= Parameter is disabled
BRK
= Input enabled; system will display
= Display is active when input is 12 volts O R
= Unit does not switch camera inputs.
= Unit switches inputs (e.g., to Stop Arm camera)
Note Make sure all
timers are disabled ( )
if not used.
= Display is active when input is grounded
POWER = Turns VCR on for temporary power
EJECT = Press to eject tape
REW = Rewind tape, search backward through images
PLAY = Play back tape
FF = Advance tape or search forward through images
STOP = Stop recording
REC = Press to record
POWER Indicator = Lights when the HTR1 is plugged into a power source
EP Indicator = Lights when the HTR1 is in EP mode
REC Indicator = Lights when the HTR1 is recording
Legend:
Receives
infrared signals
from remote
control
Tool text tip line provides setting descriptions
Loading...