Page 1
USER INFORMATION:
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION!
Explanation of two Symbols
THE GRAPHIC SYMBOLS WITH SUPPLEMENT AL MARKING ARE ON THE BOTTOM
OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT
TO RAIN OR MOISTURE"
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.
PRECAUTION:
!
All the warnings and instructions of this manual should be followed.
Remove the plug from the outlet before cleaning. Do not use liquid
aerosol detergents. Use water damped cloth for cleaning.
To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture.
Do not place anything on top of the unit that might spill or fall into it.
Do not attempt to service this unit yourself as opening or removing
covers may you to dangerous voltage or other hazards. Please refer
all servicing to qualified service personnel.
Keep enough space around the unit for ventilation.
Slots and openings on the monitor should not be blocked.
During flashes of lightning or cracks of thunder, or when the system
is not used for a long time, unplug the system power supply to
protect the unit from lightening or power surges.
P/N:3810-0071G
Rev 0 03/18
Design and specifications
are subject to change
without notice.
SPECIFICATIONS:
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total/Effective Pixels No.
S/N Ratio
Resolution
Video Output Level
Lens- Mirror Cover
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
Input/Output Connector
Power Consumption
Dome Size (Ø
)
Weight
Call 1.800.796.CCTV for sales, service and customer support.
NTSC : 525 Lines PAL : 625 Lines
2 : 1 Interlace
15.734kHz 15.625kHz
59.94Hz 50Hz
1/3 inch SONY Super HAD CCD
270K/250K 320K/290K
More than 48dB
380 TV Lines
1.0 Vp-p (75 Ohms, composite)
Fixed Lens (f=3.8mm)
Manual
Internal
0.1 Lux
1/60~100,000 Sec. 1/50~100,000 Sec.
Auto
Auto
Power (Red Jack), Video (Yellow Jack)
12VDC (10V~15V), 0.15A / 1.8W (Max)
85mm
Approx. 210g
Need Help?
www.honeywellvideo.com
HD40
Series
Operation
• 1/3” SONY Super HAD CCD
• 380 TV Lines Resolution
• Built-in Fixed Lens (f=3.8mm)
• Min. Illumination : 0.1 Lux
• Auto White Balance
• Diameter of Bubble : 85mm
• Easy Install (3-Axis)
o
t
e
i
l
n
p
s
t
m
a
i
l
S
•
l
Manual
READ AND KEEP THIS
OPERATION MANUAL
INSTALLATION:
This manual explains the installation and operating method for the
color dome camera. Before installation, make sure you are familiar
with this product's special features and proper operating technique.
Stick the guide pattern on the wall or ceiling.
1
Drill two holes according to the guide pattern
2
then insert anchors into the drilled holes.
Draw out power/video wires to the connecting
3
places.
Fixed the camera to a celling using two screws.
4
Adjust desired focus and scene by turning
5
and moving the 3-axis camera bracket by
hand.
Put the dome cover over the base.
6
Fix the dome cover on the base by covering.
7
Ceiling
Guide Pattern
Dome Base
Mounting
Screw
Dome Cover
NOTE
Insert coin to the side
hole and remove the
dome cover by twist coin.
COMPOSITION:
Operation Manual
CONNECTION:
12VDC Power Type
#
1
#
2
Video
(Yellow)
Power - 12VDC
(Red)
DIMENSIONS:
3.02”
(76.7 mm)
Dome Camera
Video Output
GND
1.34”
(34 mm)
1.68”
(42.7 mm)
Mounting Screw
• The wire is polarized.
• Use 12VDC power source.
No.
Function
Terminal Color
#1
Video Output
Yellow
#2
4.45”
(113 mm)
3.35”
(85 mm)
Power Input
2- 0.18”
(4.5 mm)
Red
Guide Pattern
Remark
1.0 Vp-p
12VDC(10V~15V),
1.8W(Max)
3.35”
(85 mm)
Built-in camera
3-axis
bracket makes it much
easier to rotate in any
direction.
360º
TROUBLESHOOTING:
If you have trouble operating
your camera, refer to the following.
If the guidelines do not enable you to solve the problem,
contact an authorized technician.
The image does not
appear on the screen.
The image on the
screen is dim.
The camera does not
work properly, the surface
of the camera case is hot,
and a black line appears
on the screen.
The screen blinks a lot.
Check the power source for the monitor
and camera and ensure that the voltage
and polarity are properly connected and
being supplied correctly.
Check if the lens is stained. If dirty,
clean the lens with a soft, clean cloth.
Adjust the Back Focus of the lens again.
Check if you have connected the camera
to a proper power source and If there is
no problem with the power, turn the unit
off immediately and seek assistance from
our Customer Service department.
Check if the camera is pointed toward
the sun or a fluorescent lamp.
Adjust the angle or location of the
camera if too much light is coming into
the screen.
90º
Tilt
360º
Horizontal
Pan
Loading...