Honeywell HD3VC4SAX User Manual

3 Inch Dome Camera

HD3VC4SHR/HD3VC4SA/HD3VC4SHRX/HD3VC4SAX Quick Install Guide

Document 900.0824 - 09/06 - Rev 1.01

Warnings, Operating Notes

Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty.

WARNING! The use of CSA Certified/UL

Listed Class 2 power adapters is required to ensure compliance with electrical safety standards.

WARNING! To reduce the risk of fire or

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product

(applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER. NO USER-SERVICEABLE PARTS INSIDE

FCC Compliance Statement

Information to the User: This equipment has

been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Caution Changes or modifications not

This Class A digital apparatus complies with Canadian ICES-003.

Manufacturer’s Declaration of Conformance

The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55022 for emissions.

Operating Notes

Power Supply

This dome camera can operate on 24 VAC or 12 VDC.

electric shock, do not expose this product to rain or moisture.

CAUTION

RISK OF

ELECTRIC SHOCK

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THE UNIT.

THIS SYMBOL INDICATES THAT IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS ACCOMPANY THIS UNIT.

expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Operating Conditions

• Avoid viewing very bright objects (example, light fixtures) for extended periods.

• Avoid operating or storing the unit in the following locations:

• Extremely humid, dusty, hot/cold

environments (where the operating temperature is outside the recommended range of 14°F to 122°F [-10°C to +50°C])

• Close to sources of powerful

electromagnetic radiation, such as radio or TV transmitters

• Close to fluorescent lamps or objects

reflecting light

• Under unstable light sources (may

cause flickering)

Introduction

The unobtrusive, compact design of the HD3VC4S Series 3 Inch Dome Camera is ideal for indoor installations in commercial and residential environments.

Before You Begin

Please read this guide carefully before you install the HD3VC4S Series 3 Inch Dome Camera. Keep this guide for future reference.

Unpack Everything

Check that the items received match those listed on the order form and packing slip. The HD3VC4S Series Camera packing box should include, in addition to this Install Guide:

• One fully assembled camera

• One hardware kit

• One 2nd video monitor output cable

• One mounting template

If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service.

Installation

The HD3VC4S Series is a fully-integrated enclosure with camera and lens.

Figure 1 Camera Parts

1 — Legend

Conduit hole used for surface run power/video

connector

2 Camera housing

3 Dome cover 4 Zoom lever 5 Focus lever

a Video output connector

24 VAC/12 VDC power input connector

(red +, black -)

Note See Figure 5 for an explanation of the

camera board settings.

Removing the Dome Cover

1. Gently turn the dome cover (#5 on

Figure 2) counter-clockwise to unlock and

pull free of the housing.

2. Remove the inner liner (#4) by gently pulling it free of the two notches (#2) in the housing (#1).

3. Set the dome (and liner) aside.

Figure 2 Dome Cover Removal

2 — Legend

1 Camera housing

2 Notches (x2)

Tilt adjustment bracke

and thumbnuts

4 Inner liner

5 Dome cover

Connecting the Wiring

Follow Figure 1 to connect the video output connector (a) and 24 VAC/12 VDC power connector (b).

Caution For DC power supply use, make sure

the polarity is correct to avoid malfunction and/or camera damage.

Mounting the Camera

1. Place the mounting template (supplied) on the mounting surface and mark the holes (see Figure 3).

2. Drill two holes, then insert the screw anchors into the holes.

3. Secure the camera housing to the wall/ ceiling with the TP4 x 15 mm tapping screws supplied.

Note Depending on the material of your

mounting surface, you may require different screws and anchors than those supplied.

Figure 3 Camera Installation

M ounting Tem plate

Logo Direction

S E A

3 2 1

L L E V E L

+ -

V PHASE

3 — Legend

1 Screw anchors (x2), supplied 2 Mounting template

3 TP4 x 15 mm tapping screws (x2) supplied

Adjusting the Camera Position

The HD3VC4S Series camera has three axes for positioning the camera. While monitoring the picture on the monitor, adjust the camera position as follows:

Horizontal Adjustment Rotate the 3D

assembly in the base. Do not turn the assembly more than 360° as this may cause the internal cables to twist and disconnect or break.

Vertical Adjustment After loosening the

thumbnuts, position the camera as desired, then finger-tighten the thumbnuts to set the position.

Horizontal Rotation For Wall Mount and Tilted Ceilings Rotate the lens base (maximum 360°)

until you are satisfied with the field of view.

Figure 4 Camera Adjustment

4 — Legend

Tilt adjustment bracket and thumbnuts (x2)

for vertical adjustment

Axis ring for horizontal rotation for wall

mount and tilted ceilings

3 Zoom lever 4 Focus lever

Rotate 3D assembly in base for horizontal

adjustment

Adjusting the Lens

1. Loosen the Zoom lever (#3) counterclockwise a little, then rotate the Zoom lever and determine the image view.

2. Loosen the Focus lever (#4) counterclockwise a little, then adjust the focus for optimum picture sharpness.

3. Re-tighten the Zoom lever and Focus lever after adjustment.

Note It is important that you lock the zoom

and focus levers after making adjustments. This will avoid the positions moving (for example, from temperature changes or vibrations).

Optional Camera Settings

See Figure 5 for location on the camera board of the camera adjustment functions described below.

Figure 5 Camera Adjustment Functions

LEVEL

V PHASE + -

LEVEL H L

V PHASE + -

5 — Legend

1 LEVEL adjustment pot (Iris level)

2 V Phase adjustment pot (24 VAC only) 3 Mode setting DIP switches

4 Monitor out 5 Camera mounting holes

Note Please use the supplied DC Iris and

Line lock adjustment tool to adjust picture brightness and phase adjustment.

Picture Brightness Use the LEVEL screw (#1)

to compensate for the iris level. L (low) makes the picture darker. H (high) makes the picture brighter.

Phase Adjustment Use the V Phase

Adjustment Pot (#2) to adjust the phase difference between cameras. Make sure Switch 4 is ON to activate the Line lock function (AC operation only).

DIP Switches Set the DIP switches (#3) to

activate or deactivate the following functions:

Switch Description

1BLC (Backlight Compensation). Set to ON to

have the camera adjust the exposure to compensate for situations where the subject is lit from behind. The factory default setting is OFF.

2AGC (Automatic Gain Control). Set to ON

(default) to have the camera adjust the picture for low light conditions.

3DC/AES Mode. Leave in ON position only. 4LL (Line Lock). Set the camera synchronization

to internal or line lock (line lock is only available with 24 VAC). The factory default setting is OFF.

ON OFF

1 2 3 4

1:BLC 2:AGC

3:DC/AES

OFF

4:LL

1 2 3 4

1: BLC 2:AGC 3 : DC/AES 4: LL

MON

Document 900.0824 - 09/06 - Rev 1.01

Attaching the Dome Cover

To attach the dome cover, follow Figure 2:

1. Use a soft, lint-free cloth to wipe the dome cover clean and remove fingerprints.

2. Attach the inner liner (#3) to the Tilt adjustment thumbnuts (#2). Push down until it clicks into place.

3. Place the dome (#4) on the unit. Make sure all three dome tabs (#5) are inside the housing opening.

4. Turn the dome gently clockwise until it locks in place.

Legend

1 Camera housing

Tilt adjustment

bracket and thumbnuts

3 Inner liner

4 Dome cover 5 Dome tabs (x3)

Routine Maintenance

• The dome cover is an optical part. Use a soft, dry cloth to remove any fingerprints or dust.

• Clean the camera housing with a soft, dry cloth. For more stubborn stains, use a cloth dampened with a small quantity of neutral detergent, then wipe dry.

Caution Do not use volatile solvents such as

alcohol, benzene or thinners to avoid damaging the surface finish.

Cable Guidelines

Maximum Power Supply Cable Length (feet/meters) Cameras With AC/DC Power Supplies

Wire gauge

Total

Power

load High

Res

Std Res 12 VDC

Caution Calculations are based on an unregulated linear

power supply, which would be the worst case. Using a regulated or switching power supply can increase the cable distance. Honeywell recommends using a CSA Certified/UL listed Class 2 power adapter to ensure compliance with electrical safety standards.

Maximum Video Coaxial Cable Length (feet/meters)

Maximum length (feet/meters) 750/229 1500/457 2000/610 * Copper clad steel core, 95% braided shield

24 AWG 22 AWG 18 AWG 16 AWG

supply 12 VDC

89/27

148/45

15 VDC

348/106

24 VAC

991/302 236/72

15 VDC

420/128

24 VAC

1155/352

Cable type RG-59 RG-6 RG-11 Wire gauge 23 AWG* 18 AWG* 14 AWG*

561/171 1601/488

384/117 679/207 1866/569

374/114 1427/435 4061/1238

977/298 1729/527 4736/1444

597/182 2273/693 6462/1970

1555/474 2752/839 7541/2299

Product Dimensions

Figure 6 Camera Dimensions

3.91” (96.3 mm)

4.33” (110 mm)

0.2” (5 mm) diameter

3.27” (83 mm)

Warranty and Service

Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective product returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service for assistance or to request a Return Merchandise Authorization (RMA) number.

Call 1.800.796.CCTV (North America only). Be sure to have the model number, serial number, and the nature of the problem available

for the technical service representative. Prior authorization must be obtained for all

returns, exchanges, or credits. Items shipped

to Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be refused.

Europe and United Kingdom

For warranty information please contact your Honeywell dealer.

Specifications Contact Information

Honeywell Video Systems (Head Office)

Video Signal Specifications

Video Standard: NTSC, PAL NTSC, PAL

High Res Standard Res

Scanning System: 525 lines, 2:1 interlace (NTSC)

625 lines, 2:1 interlace (PAL)

Image Sensor: 1/3” Interline Transfer CCD Number of Pixels

(H x V):

Minimum Illumination:

Horizontal Resolution:

Video Output: 1.0 Vp-p @ 75 Ohms S/N Ratio: 50 dB (AGC Off) Sync System: 12 VDC: Internal, 24 VAC: Line lock

Auto Gain Control: On/off, switchable BLC: On/Off, switchable AI/AES Selection: On/off, switchable

Automatic Electronic Shutter:

Lens Type: 2.8 mm to 10 mm Vari-focal Auto Iris,

Lens Iris Control: Direct Drive (DC) AI Angle of View (Lens):

Wide Tele

Focal Length: f = 2.8 mm to 10 mm White Balance: ATW

Gamma: 0.45

768 x 494 (NTSC) 752 x 582 (PAL)

0.6 lux @ F1.3 0.2 lux @ F1.3

540 TVL 350 TVL

1/60 - 1/100,000 sec (NTSC)

1/50 - 1/100,000 sec (PAL)

129.0° (D), 100.2° (H), 73.3° (V)

34.3° (D), 27.4 (H), 20.5° (V)

510 x 492 (NTSC) 500 x 582 (PAL)

(AGC on, 50 IRE)

F1.3

Electrical Specifications

Input Voltage: 12 VDC/24 VAC

Input Voltage Range: 11 to 16 VDC

Power Consumption: 3.5 W (max)

17 to 28 VAC

Mechanical

Dimensions (W x H):

Weight: Net

Shipping Construction: Housing and dome: Polycarbonate

4.33” x 3.91” (110 mm x 96.3 mm)

.66 lb (.3 Kg)

1.32 lb (.6 Kg)

Environmental

Temperature: Operating

Storage Relative Humidity: 0% to 90%, non-condensing

14°F to 122°F (-10°C to 50°C)

-4°F to 140°F (-20°C to 60°C)

Regulatory

Emissions: FCC, CE (EN55022) Immunity: CE (EN50130-4)

Safety: UL2044

Applies only to HD3VC4SHR and

, EU: 73/23/EEC LVD

HD3VC4SA models.

2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA

www.honeywellvideo.com

℡ +1.800.796.2288

Honeywell Security Australia Pty Ltd.

Unit 5, Riverside Centre, 24-28 River Road West Parramatta, NSW 2150, Australia

www.ademco.com.au

℡ +61.2.8837.9300

Honeywell Security Asia Pacific

33/F Tower A, City Center, 100 Zun Yi Road Shanghai 200051, China

www.security.honeywell.com/cn

℡ +86 21.2527.4568

Honeywell Security Asia

Flat A, 16/F, CDW Building, 388 Castle Peak Road Tsuen Wan, N.T., Hong Kong

www.security.honeywell.com/hk

℡ +852.2405.2323

Honeywell Security France

Parc Gutenberg, 8, Voie La Cardon 91120, Palaiseau, France

www.honeywell.com/security/fr

℡ +33.01.64.53.80.40

Honeywell Security Italia SpA

Via Treviso 2 / 4 31020 San Vendemiano Treviso, Italy

www.honeywell.com/security/it

℡ +39.04.38.36.51

Honeywell Security Spain

Mijancas 1. 3 P.Ind. Las Mercedes 28022 Madrid, Spain

www.security.honeywell.com/es

Planta

℡ +34.902.667.800

Honeywell Security Nederland

Netwerk 121 1446 WV Purmerend, Netherlands

www.SecurityHouse.nl

℡ +31.299.410.200

Honeywell Video Systems UK Ltd.

Aston Fields Road, Whitehouse Ind Est Runcorn, Cheshire, WA7 3DL, UK

www.honeywellvideo.com

℡ +0844.8000.235

Honeywell Security South Africa

Unit 6 Galaxy Park, 17 Galaxy Avenue Linbro Park, P.O. Box 59904 2100 Kengray, Johannesburg, South Africa

www.honeywell.co.za

℡ +27.11.574.2500

Honeywell Security Germany

Johannes-Mauthe-Straße 14 D-72458 Albstadt, Germany

www.honeywell.com/security/de ℡ +49.74 31.8 01.0

Honeywell Security Poland

Chmielewskiego 22a, 70-028 Szczecin, Polska

www.ultrak.pl

℡ +48.91.485.40.60

Honeywell Security Czech Republic

Havránkova 33, Brno Dolní Heršpice, 619 00, Czech Republic

www.olympo.cz

℡ +420.543.558.111

Honeywell Security Slovakia Republic

Vajnorskà 142, 83104 Bratislava Slovakia

www.olympo.sk

℡ +421.2.444.54.660

www.honeywellvideo.com

+1.800.796.CCTV (North America only)

HVSsupport@honeywell.com

900.0824 - 09/06 - Rev 1.01

© 2006 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.