Page 1
800-18606 – A – 06/2014
Performance Series
HD273H(X)
True Day/Night Outdoor Fixed Minidome with IR LEDs
User Guide
Page 2
2 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Thank you for purchasing our product. If there are any
questions, or requests, please do not hesitate to contact the
dealer.
The information in this publication is believed to be accurate in
all respects. However, Honeywell cannot assume responsibility
for any consequences resulting from the use thereof. The
information contained herein is subject to change without notice.
Revisions or new editions to this publication may be issued to
incorporate such changes.
Regulatory Information
FCC Information
FCC compli an ce: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or televis i on rec ept i on, whic h c an be det erm ined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
Page 3
3 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
NOTE: Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme
NMB-003 du Canada.
EU Conformity Statement
This product and - if applicable - the supplied
accessories comply with the applicable
harmonized European standards listed under th e
Low Voltage Directive 2006/95/EC, the EMC Directive
2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symb ol c ann ot be dis p ose d of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment,
or dispose of it at des ign ate d c oll ecti on points . Fo r more
information, see: www.recyclethis.info.
Page 4
4 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Safety Instructions
These instructions are intended to ensure that users can use
the product correctly to avoid danger or property loss.
The precautions are divided into “Warnings” and “Cautions”.
Warnings: Serious injury or death may occur if any of the
warnings are neglected.
Cautions:
Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
WARNING: Installation and servicing should be performed only
by qualified and experienced technicians to conform to all local
codes and to mai ntain your warr anty.
WARNING: This device is configured for 24 V AC or 12 V DC
operation. Do not connect to a higher voltage. U se onl y wit h
NRTL approved Class 2 or LPS power supplies.
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.
Page 5
5 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Cautions
CAUTION: The light emitted from the near-infrared light
emitting dio des (LEDs) pr ovides illum in ati o n over a wi de ar ea.
This light is not considered a risk to the unshielded human eye.
However, as with any light source, it is recommended that
normal preca ut i ons be taken to avoi d unne cessary exposure.
For example, avoid staring into the beam or viewing the LEDs
directly with optical instruments at close range.
Important Safet y In struct io ns
Read and keep these instructions.
Ensure that your installation area can safely support 3 times
the weight of the camera.
Do not install the camera in extreme temperature conditions.
Only use the camera where temperatures are within the
limits shown in the camera specifications. Be especially
careful to pro vid e ve ntil a tion wh en op er ati n g unde r high
temperatures.
Do not install indoor rated cameras where they will be
exposed to rain or moisture.
To prevent damage to the imager, do not aim the camera
toward an extreme light source.
Do not touch the camera lens, dome or bezel (front glass
plate).
Do not drop the camera or subject it to physical shock.
Page 6
6 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Do not use strong or abrasive cleaners, clean only with a
soft cloth and mild detergent or alcohol.
Do not open the camera or attempt to service it yourself.
Refer all service issues to your dealer.
Page 7
7 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Table of Contents
Introduction .................................................................................... 9
Product Fe atu res ................................................................ 9
Overview ........................................................................... 10
Installation .................................................................................... 11
Surface Mo unti ng the Camera on a Ceiling .................. 12
In-ceiling Mounting the Camera ..................................... 17
In-ceiling Mounting the Camera with a Gang Box ........ 20
Adjusting the Image and Focus ...................................... 23
Menu Description ........................................................................ 25
AE (Auto Exposure) ......................................................... 26
BRIGHTNESS .......................................................... 27
AE MODE .................................................................. 27
AGC ........................................................................... 27
SENSE UP ................................................................ 28
WB ..................................................................................... 28
AUTO ......................................................................... 28
MANUAL.................................................................... 28
DAY & NIGHT ................................................................... 29
COLOR ...................................................................... 29
B/W ............................................................................ 29
SMART ...................................................................... 29
VIDEO SETTING ............................................................. 30
SCREEN RATIO ....................................................... 31
CONTRAST .............................................................. 31
SHARPNESS ............................................................ 31
Page 8
8 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
COLOR GAIN ........................................................... 32
3D NR ........................................................................ 32
MIRROR .................................................................... 32
FUNCTION ....................................................................... 33
DETECTION ............................................................. 33
MASKING .................................................................. 36
ZOOM IN ................................................................... 38
LANGUAGE .............................................................. 38
RESET ............................................................................... 38
SAVE &EXIT ..................................................................... 38
Page 9
9 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Introduction
Product Features
This seri es of camera adopts a high pe rfo rm anc e imaging
sensor and advanced circuit board design technology. It
features high resolution, low distortion, and low nois e. It is ideal
for surveillance systems and ima ge pr o ces sing systems.
The main features are as follows:
• High perform ance CMOS sensor supplies hi gh res olution
high-quali t y im age s
• Low illumination, 0.1 Lux @ F1.2 (AGC ON), 0 Lux with IR
LEDs on
• IR cut filter with automatic switching
• OSD menu, parameters are configurable
• Auto white bal an ce, aut o gai n contr ol , e lec tr onic shu tte r
control an d inter nal s ynchronizati o n
• Advanced Engineering Design and patented universal
adjustable structure provides convenient adjustment and
high reliability
• SMART IR mode
• Advanced 3-axis design meets different installation
requirements
• Ingress protection: IP66-rated
Page 10
10 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Overview
Figure 1-1 Overview of Camera
Table 1-1 Description
No. Description No. Description
1
Auxiliary Video
Output
5 Back Box
2 Menu Button 6 Power Cable
3 Black Liner 7 Video Cable
4 Lens 8 Bubble
Page 11
11 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Installation
Before you start:
• Please make sure that the camera is in good condition and
all of the assembly parts are included.
• Make sure that all related equipment is powered-off during
the installation.
• Check that the camera specification agrees with the
installation environment.
• To avoid damage, ensure the power supply voltage
matches yo ur cam er a req ui r em ent s.
• Please make sure the installation surface is strong enough
to withstand three times the weight of the camera a nd the
mounting.
• If the installation surface is concrete, you need to insert
expansion screws before you install the camera. If the
installation surface is wood, you can use self-tapping
screws to secure the camera.
• If the product does not function properly, please contact
your dealer or the nearest service center. Do not
disassemble the camera for repair or maintenance by
yourself.
Page 12
12 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
For the camera that supports IR, you are required to pay
attention to the following precautions to prevent IR reflection:
• Dust or greas e on the dom e cover will caus e IR refl ection.
Please do not remove the dome cover film until the
installation is finished. If there is dust or grease on the
dome cover, clean the dome cover with clean soft cloth and
isopropyl alcohol.
• Make sure that there is no reflective surface too close to
the camera lens. The IR light from the camera may reflect
back into the lens and obscure the image.
• The foam ring around the lens must be seated flush against
the inner surface of the bubble to isolate the lens from the
IR LEDs. Fasten the dome cover to the camera body so
that the foam ring and the dome cover are seamlessly
connected.
Surface Mounting the Camera on a Ceiling/Wall
Steps:
1. Attach the mounting template (supplied) to the place where
you want to install the camera, and then drill the screw
holes and cable hole (if needed) in the ceiling/wall
according to the mounting template (see Figure 1-2).
Page 13
13 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Figure 1-2 HD27 3H( X) Mou ntin g Template
2. Loosen the three screws on the edge of the bubble with the
supplied screwdriver to remove the bubble and the black
liner.
3. Remove the camera from the back box.
Figure 1-3 Removing the Camera from the Back Box
Page 14
14 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
4. Attach the back box to the ceiling/wall by aligning the holes
of the back box with the holes drilled in step 1 and secur e it
to the ceiling/wall with the supplied screws (see Figure 1-4).
Figure 1-4 Securing the Back Box
5. Route the cables through the c abl e hole.
6. Align the camera with the back box, and tighten the set
screws to secure the camera with the back box.
Page 15
15 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Figure 1-5 Aligning the Camera
7. Connect the vid eo ou tpu t (BNC) con ne ct or to the monitor.
Connect the power connector to the power supply.
8. Adjust the image and focus. Please refer to the Adjusting
the Image and Foc us s ection on page 23 for more details.
9. Fit the black liner back onto the camera (see Figure 1-6).
Page 16
16 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Figure 1-6 Fitting the Black Liner
10. Tighten the screws to secure the bubble with the bac k box.
Figure 1-7 Securing the Bubble
Page 17
17 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Remove the protection film softly after the installation is
complete. Leaving the film on the bubble during installation will
protect it from scratches during the installation process.
In-ceiling Mounting the Camera
You need t o purchase an in-ceiling mount separately if your
installation requires an in-ceiling mounting.
Steps:
1. Attach the mounting template (supplied) to the place where
you want to install the camera, and then drill the screw
holes and cable hole in the ceiling according to the
mounting template.
2. Secure the in-ceiling mount with two mounting screws as
shown in Figure 1-8.
Figure 1-8 Securing the In-c ei ling Mount
3. Route the cables through the hole in the center of the
in-ceiling mount.
Page 18
18 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
4. Align the camera with the in-ceiling mount, and tight en t h e
set screws to secure the camera with the in-ceiling mount.
Figure 1-9 Securing the Camera
5. Connect the video output (BNC) con nector to the moni t or.
Connect the power connector to the power supply.
6. Adjust the image and focus. Please refer to the Adjusting
the Image and Foc us secti on on pa ge 23 for more detailed
information.
7. Fit the black liner back onto the camera (see Figure 1-10).
Page 19
19 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Figure 1-10 Fitting the Black Liner
8. Align the bubble with the in-ceiling mount, and then tighten
the screws to secure the bubble to the in-ceiling mount.
Figure 1-11 Aligning the Bubble
Page 20
20 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Remove the protection film softly after the installation is
complete. Leaving the film on the bubble during installation will
protect it from scratches during the installation process.
In-ceiling Mounting the Camera with a Gang Box
Steps:
1. Secure the in-ceiling mount (supplied) to the gang box with
two screws.
Figure 1-12 Securing the In-ceiling Mount to the Gang Box
2. Route the cables through the hole in the center of the
in-ceiling mount.
3. Align the camera with the gang box, and tighten the screws
to secure the cam e ra wi th the ga ng bo x (see Figure 1-13).
Page 21
21 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Figure 1-13 Securing the Camera
4. Connect th e video output (BNC) con ne ctor to t he monit or.
Connect the power connector to the power supply.
5. Adjust the image and focus. Please refer to the Adjusting
the Image and Focus section on page 23 for more details.
6. Fit the black liner back onto the camera (se e Figu re 1-14).
Page 22
22 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Figure 1-14 Fitting the Black Liner
7. Align the bubble with the in-ceiling mount, and tighten the
screws to secure the bubble to the in-ceiling mount.
Figure 1-15 Securing the Bubble
Page 23
23 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Remove the protection film softly after the installation is
complete. Leaving the film on the bubble during installation will
protect it from scratches during the installation process.
Adjusting the Image and Focus
Steps:
3-axis surveillance angle adjustment (refer to Figure 1-16 while
adjusting the angle):
• View the camera image with the connected monitor.
• Rotate the panning table to adjust the pan direction
[0°~355°].
• Loosen the tilting lock screw.
• Rotate the tilting table to adjust the tilt direction [0°~90°].
• Tighten the tilting lock screw.
• Rotate the camera [0°~355°] to adjust the lens to the
optimum s urveillanc e angle.
Page 24
24 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Figure 1-16 3-axis Angle Adjustment
Zoom and focus adjustment (refer to Figure 1-17 while
adjusting the zoom and focus):
• View the camera image with the connected monitor.
• Loosen the zoom lever and move the screw between T
(Tele) and W (Wide) to obtain the optimum zoom setting.
• Tighten the zoom lever.
• Loosen the focus lever and move the screw between F
(Far) and N (Near) to obtain the optimum focus setting.
• Tighten the focus lever.
Page 25
25 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Figure 1-17 Zoom and Focus Adjustment
Menu Description
Setup
AE
WB
DAY
&NIGHT
VIDEO
SETTING
FUNCTION
RESET
SAVE
&EXIT
BRIGHTNESS
AE MODE
AGC
SENSE UP
AUTO
MANUAL
COLOR
B/W
CONTRAST
SHARPNESS
COLOR
GAIN
3D NR
MIRROR
DETECTION
MASKING
ZOOM IN
LANGUAGE
SMART
Figure 1-18 Main Menu Overview
Zoom Lever
Focus Lever
Page 26
26 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
This camera uses a joystick to select the menu and confirm
a selection (see Figure 1-1 for the joystick location).
Move the joystick up/down to select a menu item.
Move the joystick left/right to adjust the value of the
selected item.
Press down on the joystick to confirm a selection. The
menu button mentioned in the chapter below refers to the
joystick.
AE (Auto Exposure)
AE describes the brightness-related camera parameters. Y ou
can adjust the image brightness by changing the
BRIGHTNESS, AE MODE, AGC, and SENSE-UP values in
different light conditions.
AE
1. BRIGHTNESS 1-|--10
2. AE MODE DWDR
3. AGC OFF
4. SENSE UP 0-|---16
5. RETURN
Figure 1-19 AE Menu
Page 27
27 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
BRIGHTNESS
Brightness refers to the brightness of the image. You can set
the brightness value from 1 to 10 to darken or brighten the
image. The higher the selected value, the brighter the image is.
AE MODE
You can set AE mode as GLOBAL AE or D-WDR.
GLOBAL AE
GLOBAL AE refers to the normal exposure mode which is
for adjustin g to situations including unusual lighting
distribution, variations, non-standard processing, or other
conditions of under exposure to get an optimum image.
D-WDR
The digital wide dynamic range (D-WDR) function helps the
camera provide clear images even under back light
circumstances. When there are both very bright and very
dark areas simultaneously in the field of view, D-WDR
balances the brightness level of the whole image and
provides clear images with visible details.
AGC
AGC is a form of amplification where the camera will
automatically boost the image received in much lower light
conditions than standard lighting in order to optimize the clarity
of an image in a poorly lit scene. The AGC level can be set to
HIGH, MIDDLE, or LOW. Select OFF to disable AGC.
Page 28
28 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
The noise will be amplified if the AGC is on.
SENSE UP
SENSE-UP increases the exposure on a single f ram e , whi ch
makes a camera more sensitive to light so it can produce
images even in low lux conditions. You can set the SENSE UP
value from 0 to 16 according t o the differe nt light c on diti o ns.
The higher the sele cte d value, the more frames are integrated
in a unit of time.
WB
White balance is the white rendition function of the camera to
adjust the color temper at ure acc or din g to the env i ro nm ent . It
can remove the unrealistic colors cast in the image. You can set
WB mode as AUTO, or MANUAL.
AUTO
In AUTO mode, white balance is being adjusted automatically
according to the color temperature of the scene illumination.
MANUAL
You can set the R GAIN/B GAIN valu e f rom 1 to 10 to adjust
the shades of red/blue color of the image.
Page 29
29 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
MANUAL
1. R GAIN 1-|--10
2. B GAIN 1-|--10
3. RETURN
Figure 1-20 Manual White Balance Setting
DAY & NIGHT
Color, B/W, and SMART are selectable for DAY and NIGHT
switches.
COLOR
The image is colored in day mode all of the time.
B/W
The image is black and white all the time, and the IR LEDs turn
on in low-light conditions.
SMART
You can select to turn the INFRARED LAMP on/off and set the
SMART IR value in this menu.
Page 30
30 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
DAY & NIGHT
1. INFRARED_LAMP OFF
2. SMART IR 0-|--5
3. RETURN
Figure 1-21 Day & Night Menu
INFRARED LAMP
You can select to turn the IR LEDs ON/OFF to respond to
the requirements of different circumstances.
SMART IR
The Smart IR function is used to adjust the light to its most
suitable intensity, and to prevent the image from over
exposure. The SMART IR value can be adjusted from 0 to
5. The higher the selected value, the more obvious the
SMART IR effects are. SMA R T IR is disabled when the
value is 0.
VIDEO SETTING
Move the cursor to VIDEO SETTING. Press the confirm button
to enter the VIDEO SETTING submenu (se e Figu re 1-22).
PICTURE RATIO, CONTRAST, SHARPNESS, COLOR GAIN,
3D NR and MIRROR are adjustabl e video settings.
Page 31
31 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
VIDEO SETTING
1. SCREEN RATIO 4:3
2. CONTRAST 1-|--10
3. SHARPNESS
4. COLOR GAIN 1-|--10
5. 3D NR OFF
6. MIRROR OFF
7. RETURN
Figure 1-22 Video Setting Menu
SCREEN RATIO
You can set the SCREEN RATIO as 4:3 or 16:9 with this
function.
CONTRAST
This feature enhances the difference in color and light between
parts of an image. You can set the CONTRAST value from 1 to
10.
SHARPNESS
Sharpness determines the amount of detail an imaging system
can reproduce. And you can adjust the EDGE/DETAIL
sharpness value by entering the SHARPNESS submenu.
Page 32
32 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
SHARPNESS
1
. EDGE 1-
|--10
2
. DETAIL 1-
|--10
3. RETURN
Figure 1-23 Sharpness Menu
You can set the edge and detail sharpness value from 1 to 10
accordi ng to the actual requir ement. A higher sharpness value
results in a clearer and sharper image.
COLOR GAIN
Adjust this feature to change the saturation of the color . The
value ranges from 1 to 10.
3D NR
Compared to traditional, general 2D NR technology, 3D NR
processes the noise reduction between two frames instead of in
one frame. It ca n decr ea se the noi s e effec t, es pec i al l y when
capturing moving images in low-light conditions and delivering
more accurate and sharp image quality.
You can set the 3D NR level as High, Middle, and Low. Select
OFF to disable the 3D NR feature.
MIRROR
OFF, H, V, and HV are selectable settings for mirror.
Page 33
33 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
OFF: The mirror function is disabled.
H: The image flips 180 degrees horizontally.
V: The image flips 180 degrees vertically.
HV: The image flips 180 degrees both horizontally and
vertically.
FUNCTION
In the FUNCTION su bm en u, you c an set options for detection,
maski ng, zoom in/ out an d the language of the camera.
FUNCTION
1. DETECTION
2. MASKING
3. ZOOM IN 50-|--100
4. LANGUAGE ENGLISH
5. RETURN
Figure 1-24 Function Menu
DETECTION
In the user-defined detection surveillance area, the moving
object ca n be det ected and the alarm w ill be trigge red .
Page 34
34 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
DETECTION
1. SENSITIVITY HIGH
2. AREA NO.0
3. AREA NO.1
4. AREA NO.2
5. AREA NO.3
6. RETURN
Figure 1-25 Detection Menu
SENSITIVITY
Sensitivity refers to the sensitivity levels of the motion
detectio n, whi ch can be set to WEAK, LOW, MIDDLE or
HIGH. Higher sensitivity causes a faster response to the
motion.
AREA
There can be 4 surveillance areas set for motion detection.
Select an area an d foll o w the steps below to set the area
for motion detection.
Page 35
35 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
AREA
1. STATUS OFF
2. COLOR
WHITE
3. HORIZON SIZE 0
4. VERTICAL SIZE 0
5. HORIZON MOVE 0
6. VERTICAL MOVE 0
7. RETURN
Figure 1-26 Setting a Detection Area
Steps:
1. Set the STATUS as ON to enable the motion detection area.
2. Move the cursor to COLOR, and select a color for the area’s
border.
3. Move the cursor to HORIZON SIZE and move the joystick
left/right to define the horizontal size of the selected motion
area.
4. Move the cursor to VERTICAL SIZE and move the joystick
left/right to define the vertical size of the selected area.
5. Move the cursor to HORIZON MOVE and move the joystick
left/right to define the horizontal position of the selected
area.
6. Move the cursor to VERTICAL MOVE and move the
joystick left/right to define the vertical position of the
selected ar ea.
Page 36
36 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
7. Select RETURN to go back to the DETECTION menu. You
can clearly see the defined area with its colored border
displayed on the screen.
MASKING
The masking feature all o ws you to cover sensitive areas of an
image which should not be viewed or recorded. Up to 8
masking areas are configurable.
MASKING
1. COLOR WHITE
2. AREA NO.0
3. AREA NO.1
4. AREA NO.2
5. AREA NO.3
6. AREA NO.4
7. AREA NO.5
8. AREA NO.6
9. AREA NO.7
10.RETURN
Figure 1-27 Masking Menu
COLOR
You can set the color of the mask used to block the image
area.
AREA
There can be 8 masking areas set for masking an image
area. Select an area and follow the steps below to set up
the selected mask.
Page 37
37 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
AREA
1. STATUS OFF
2. HORIZON SIZE 0
3. VERTICAL SIZE 0
4. HORIZON MOVE 0
5. VERTICAL MOVE 0
6. RETURN
Figure 1-28 Setting a Masking Area
Steps:
1. Set the STATUS as ON to enable the masking area.
2. Move the cursor to HORIZON SIZE and move the joystick
left/right to define the horizontal siz e of the sel ec te d
masking area.
3. Move the cursor to VERTICAL SIZE and move the joystick
left/right to define the vertical size of the selected masking
area.
4. Move the cursor to HORIZON MOVE and move the joystick
left/right to define the horizontal position of the selected
masking area.
5. Move the cursor to VERTICAL MOVE and move the
joystick left/right to define the vertical position of the
selected masking area.
Page 38
38 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
6. Select RETURN to go back to the MASKING menu. You
can clearly see the masked area with its colored block
displayed on the screen.
ZOOM IN
The ZOOM IN value can be adjusted from 50 to 100.
LANGUAGE
Chinese and English are selectable languages for this camera.
RESET
Reset all the settings to their default settings.
SAVE &EXIT
Move the cursor to SAVE & EXIT and press OK to save th e
setting and exit the menu .
Page 39
39 HD273H( X) Minidome Camera User Guide
800-18606 – A – 06/2014
Page 40
www.honeywellvideo.com
+1.800.323.4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
Document 800-18606 – Rev A – 06/2014
© 2014 Hon eywell Inter nat i on al Inc. All rights reserved. No part
of this publication may be reproduced by any means without
written permission from Honeywell. The information in this
publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences
resulting from the use thereof. The information contained herein
is subject to change without notice. Revisions or new editions to
this publication may be issued to incorporate such changes.
Loading...