Page 1
HD262
CAUTION
THIS SYMBOL INDICATESTHAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESEN T
WITHIN THE UNIT.
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTSINSID E.
REFER SERVICING TOQUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATESTHAT
IMPORTANTOP ERATING AND•
MAINTENANCE INST RUCTIONS
ACCOMPANYTHIS UNIT.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
True Day/Night Indoor Fixed
Minidome Camera with IR LEDs
Quick Installation Guide
800-11990 - B - 06/2012
FCC Compliance Statement
Information to the user: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
CAUTION Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Canadian Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty
period Honeywell will repair or replace, at its sole option, free of charge, any defective
product returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service
at 1.800.796.CCTV for assistance or to request a Return Merchandise Authorization (RMA)
number.
Be sure to have the model number, serial number, and the nature of the problem available
for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items sh ipped
to Honeywell without a clearly identified Return Merchandise Authorization (RMA)
number may be refused.
1. Warnings and Cautions
WARNIN G
only by qualified and experienced technicians to conform to all
local codes and to maintain your warranty.
WARNIN G
Certified/UL Listed Class 2 power adapters to ensure
compliance with electrical safety standards.
WARNIN G
operation. Do not connect to a higher voltage. Use only with
NRTL-approved Class 2 power supplies.
CAUTION The light emitted from the near-infrared light emitting
diodes (LEDs) provide illumination over a wide area. This light is not
considered a risk to the unshielded human eye. However, as with any
light source, it is recommended that normal precautions be taken to
avoid unnecessary exposure. For example, avoid staring into the beam or
viewing the LEDs directly with optical instruments at close range.
CAUTION IR LEDs may be warm after prolonged use.
Installation and servicing should be performed
24 V AC/12 V DC cameras require the use of CSA
This device is configured for 24 V AC or 12 V DC
2. Important Safety Instructions
• Read and keep these instructions.
• Please ensure that your installation area can safely support the
weight of the camera.
• Do not install the camera in extreme temperature conditions.
Only use the camera where temperatures are within the limits
shown in the specifications section of the guide. Be especially
careful to provide ventilation when operating under high
temperatures.
• Do not aim the camera toward an extreme light source to
prevent damage to the CCD.
• This camera is rated for indoor operation. Do not expose this
camera to rain or moisture.
• Do not touch the camera lens, dome, or bezel (front glass
plate).
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the
camera.
800-11990 - B - 06/2012
Page 2
2 | HD262 TDN IR Indoor Dome Camera
Video (Yellow)
BNC
Power (Red)
24 VAC/12 VDC
Power (+)
Power (–)
Video Signal
Video GND
POWER VIDEO
OSD Controller
Video Out
Zoom
Focus
Align “LOCK”
and “” to
install cover.
3. Package Includes
•Camera (1)
• Quick Install Guide (1)
•User Guide (1)
•Screws (2)
• Video test cable (1)
• 2-conductor pigtail (1)
4. Key Features
•1/3″ interline transfer CCD
• True Day/Night with movable IR cut filter
• 620 TV lines resolution
• 2.8–12 mm (F1.4) VFAI lens, F1.4
• 0 lux minimum illumination (IR LEDs on)
• Up to 65 ft (20 m) of IR illumination
• Sens-up (×2 to ×1024)
• Digital noise reduction (DNR)
• Backlight compensation (BLC)
• Motion detection (4 zones)
• Privacy masking (8 zones)
• Local video output
• Dual power (24 VAC/12 VDC)
5. Connecting the Cables
6. Setting Up the Camera
1. Remove the dome cover from the base. Insert a coin into the slot and twist to pry the cover from the base.
2. Connect the video and power cables to the camera.
3. Attach the base to the mounting surface using the supplied screws.
4. Connect a portable monitor to the 2-pin video out connector on the camera control board using the supplied video test cable.
5. Open the lens shroud to expose the focus and zoom controls. Brace your forefinger against the back of the lens assembly and pull back the shroud with your thumb (see photo).
6. Position the camera and adjust zoom and focus as needed.
Securing Dome Cover
www.honeywellvideo.com
+1.800.796.CCTV ( North America only )
HVSsupport@honeywell.com
© 2012 Honeywell Internat ional Inc. All rights reserved. No part of this publication may be reproduced by any
means without written permission from Honeywell. The information in this publication is beli eved to be accurate
in all respects. However, Honeywell ca nnot assume responsibility for any consequences resulting from the us e
thereof. The information contain ed herein is subject to change without notice. Revisio ns or new editions to this
publication may be issued to incorporate such changes.
Document 800-11990 – Rev B – 06/2012
www.honeywellvideo.com
7. Configure the camera on-screen display (OSD) menu settings using the OSD controller on the camera control board.
8. Close the lens shroud and replace the dome cover, aligning the on
the cover with the red “LOCK” mark on the base (see drawing below).
7. Specifications
Video Standard NTSC
Scanning System 2:1 Interlace
Image Sensor 1/3” interline transfer CCD
Number of Pixels (H × V) 768 × 494
Minimum Illumination 0 lux (IR LEDs on)
Horizontal Resolution 620 TVL
Video Output 1.0 Vp-p, 75 ohms
Sync System Internal/Line lock
S/N Ratio 50 dB or more (AGC off)
Lens Type 2.8–12 mm VFAI, DC drive, F1.4
IR LEDs 850 nm, 28 LEDs
IR Illumination Distance Up to 65 ft (20 m)
DNR Auto/Off/Low/Mid/High
BLC/HSBLC Off/On
Day/Night Color/BW/Auto/Ext
Gain Control Off/Low/Mid/High
White Balance ATW/AWC/Manual
Sens-Up Auto (×2 to ×1024)
Motion Detection Off/On (4 programmable zones)
Privacy Masking Off/On (8 programmable zones)
D-WDR Off/On (Level adjustable)
Sharpness Off/On (Level adjustable)
Mirror Horizontal
Smart IR Off/On (Level adjustable)
Input Voltage 24 VAC/12 VDC
Power Consumption 5 W (max)
Temperature
Dimensions (L × W × D) 5.12” × 5.12” × 4.02” (130 mm × 130 mm × 102 mm)
Weight 0.66 lb (300 g)
Operating: 14°F to 122°F (–10°C to 50°C), RH 95% max
Storage: –4°F to 140°F (–20°C to 60°C), RH 95% max
Loading...