Honeywell HD30HD1, HD30HD1X, HD231HD2, HD73HD1 Installation Manual

Performance Series HQA HD30HD1(X)

1

Mounting Base

Base ring

Middle ring

Camera body

2

720p Indoor/Outdoor IR Ball Camera 1

Quick Installation Guide

Document 800-19473 – Rev A – 12/2014

Thank you for purchasing a Honeywell Performance Series HQA HD30HD1(X) camera. Follow the
instructions in this guide to install and set up your camera.

Cautions and Warnings

WARNING

voltage. Use only with NRTL-approved Class 2 power supplies.

WARNING

Do not stare directly into the lamp at a distance of less than 3.3 ft (1 m).

CAUTION

Important Safeguards

• Read and keep these instructions.

• Do not aim the camera toward a bright light source for extended periods to prevent damage to the
imager. Avoid operating the unit under or close to unstable light sources or close to fluorescent
lamps or objects reflecting light.

• Do not touch the camera lens.

• Do not drop the camera or subject it to physical shock.

• Do not use a strong or abrasive detergent when cleaning the camera.

• Avoid operating or storing the unit in extremely humid, dusty, or environments where the operating
temperature is outside the recommended range of –22°F to 140°F (–30°C to 60°C).

Dimensions

This device is configured for 12 V DC operation. Do not connect to a higher

IR emitted from this product. Do not view directly with optical instruments.

Class 1 LED product. Invisible LED radiation (850 nm). Avoid exposure to beam.

Before You Begin

Before you begin, check that you have received all of the parts listed below. If any parts are missing or
damaged, contact your dealer immediately.

• Camera • Self-tapping screws (4)

• Quick Installation Guide • Plastic anchors (4)

• Mounting template sticker • Power pigtail

• Allen key (L-wrench)

Tools needed (not supplied):

• Cordless drill

•Phillips screwdriver

Preparing the Mounting Surface

1. Inspect the site where you want to install the camera. The mounting surface must be flat and capable
of supporting at least three times the weight of the camera.

2. Remove the backing from the mounting template sticker and affix the sticker to the mounting surface.

3. Drill the screw holes and cable exit hole at the locations indicated on the mounting template sticker.

4. Insert the four supplied plastic anchors in the holes.

5. Pull the power and video cables through the hole.

Mounting the Camera

1. Remove the mounting base from the camera.

a. Loosen the two set screws on the base ring.

b. Unscrew the base ring from the mounting

base.

2. Attach the mounting base to the mounting surface
using the supplied screws.

3. Connect the power and video cables.

a. Connect the power connector of the camera

to a 12 V DC power source.

b. Connect the BNC connector of the camera

to a coaxial video cable.

Document 800-19473 – Rev A – 12/2014

2 | HD30HD1(X) Camera Quick Installation Guide

4. Rotate the middle ring and camera body to set the camera position.

5. Tighten the base ring to lock the camera position, and then tighten the two set screws.

Regulatory Statements

FCC Compliance

Information to the User

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

Note

authority to operate the equipment.

Canadian Compliance

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

Manufacturer’s Declaration of Conformance

North America The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.

Europe

The manufacturer declares that the equipment supplied is compliant with the European Parliament and Council

Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment (2011/65/EU)
and the essential requirements of the EMC directive (2004/108/EC), conforming to the requirements of standards EN 55022
for emissions, EN 50130-4 for immunity, and EN 60950-1 for electrical equipment safety.

This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.

This equipment has been tested and found to comply with the limits for a Class B digital device,

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the
European Union and other European countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures

www.honeywell.com/security

[phone] (North America only)

https://www.honeywellsystems.com/ss/techsupp/index.html

Document 800-19473 – Rev A – 12/2014

© 2014 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

www.honeywell.com/security/uk

[phone] (Europe only)