Honeywell HD14C4HR6, HD14C4HR6X, HD14C4HR9, HD14C4HR9X, HD14W4HR6 Installation Manual

Document 900.0342 – 10/05 – Rev 1.01

Installation Guide

Value Vandal

Dome Camera

NTSC / PAL

HD14C4HR6 HD14C4HR6X
HD14C4HR9 HD14C4HR9X
HD14W4HR6 HD14W4HR6X
HD14W4HR9 HD14W4HR9X
HD14D4HR6 HD14D4HR6X
HD14D4HR9 HD14D4HR9X

Revisions

Issue Date Revisions

1.00 09/05 New document.

1.01 10/05 Updated back cover, removed UTP
termination board

Rev 1.01 ii Document 900.0342

10/05

Rev 1.01 iii Document 900.0342

10/05

Warnings

Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.

WARNING! The use of CSA Certified/UL Listed Class 2 power adapters

is required to ensure compliance with electrical safety
standards.

Explanation of Graphical Symbols

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of

this product (applicable in the European Union and other European
countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws,
regulations, and procedures.

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER.

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.

THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.

CAUTION

Rev 1.01 iv Document 900.0342

10/05

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply

with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules,
these limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.

Caution Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to
operate the equipment.

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à norme NMB-003 du

Canada.

Manufacturer’s Declaration of Conformance

The manufacturer declares that the equipment supplied with this guide is
compliant with the essential protection requirements of the EMC directive 89/336/
EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the
requirements of standards EN 55022 for emissions.

Rev 1.01 Document 900.0342

10/05

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mounting Directly to a 4S Electrical Box . . . . . . . . . . . . . . . . . . .2

Surface Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Flush Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Connecting the Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Adjusting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Dip Switch Functions (Color Cameras, Including TDN Models) 7

Adjustment Method (Color Cameras) . . . . . . . . . . . . . . . . . . . . .8

White Balance Adjustment Method (Color Cameras) . . . . . . . . .8

Manually Setting Shutter Speed (Color Cameras) . . . . . . . . . . .9

Dip switch functions (WDR cameras) . . . . . . . . . . . . . . . . . . . .10

Adjustment method (Wide Dynamic Range Cameras) . . . . . . .10

Adjusting the Line Lock (Vertical Phase) for 24 VAC Operation 11

Adjusting the Backlight Compensation . . . . . . . . . . . . . . . . . . .11

Securing the Enclosure Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Routine Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Dome Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cable Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Rev 1.01 1 Document 900.0342

10/05

Introduction

The HD14 Series is Honeywell’s value line of vandal-resistant, fully-integrated
CCTV dome cameras. The HD14 series enclosure is designed for easy
installation and setup.

Before You Begin

Unpack Everything

Check that the items received match those listed on the order form and packing
slip. The HD14 series packing box should include, in addition to this User Guide:

• One HD14 series camera

• One hardware kit

• One product warranty
If any parts are missing or damaged, contact the dealer you purchased the

camera from or call Honeywell Customer Service (see “Warranty and Service” on
page 14).

Equipment Required

You will require the following tools to complete the installation:

• Phillips screwdriver

• Mounting screws. Use mounting screws appropriate to your installation
(capable of holding at least twice the weight of the camera).

Please read this guide carefully before
you install the HD14 series camera. Keep
this guide for future reference.

Rev 1.01 2 Document 900.0342

10/05

Installation

Your HD14 camera is weather-sealed for indoor or outdoor locations. The wiring
can be completely concealed for maximum vandal and tamper resistance.

Mounting the Camera

The HD14 camera is designed to be flush or surface mounted on a wall or ceiling.
Your HD14 comes with an adapter plate that can be used to provide the most
flexible mounting options.

Mounting Directly to a 4S Electrical Box

1. Follow Figure 1 to mount the HD14 directly to a 4S electrical box.

2. The optional adapter plate can be used to cover ceiling or wall imperfections
around the electrical box opening. Secure the optional adapter plate to the
4S electrical box using appropriate screws (not supplied).

3. Secure the HD14 base with #8-32 x 3/8 inch machine screws (not supplied).

Figure 1 4S Electrical Box Installation

4S electrical box
(not supplied)

Adapter plate (use is
optional)

HD14 base

8-32 x 3/8 inch
machine screws (x3)