Honeywell HD010, HD110 User Manual

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS AIR PURIFIER

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before operating the

air purifier.

2. Place air purifier where it is not easily

knocked over by persons in the household.

Always turn the air purifier to the OFF position

and unplug from the wall outlet when not in use.

To disconnect the air purifier, press the

Power ( ) button or turn the knob to the off position (O) to turn the air purifier off, grip the plug and pull it from the wall outlet. Never pull by the cord.

5. Do not use any product with a damaged

cord or plug or if product malfunctions, is dropped or damaged in any manner. Keep the cord away from heated surfaces.

6. Do not use air purifier outdoors.

7. Never use air purifier unless it is fully

assembled.

8. Do not run power cord under carpets, and

do not cover with throw rugs. Arrange cord such that it will not be tripped over.

9. Do not use air purifier where combustible

gases, vapors or an oxygen rich environment are present.

10. Do not expose the air purifier to rain, or use

near water, in a bathroom, laundry area or other damp location.

11. The air purifier must be used in its upright

position.

12. Do not allow foreign objects to enter

ventilation or exhaust opening as this may cause electric shock or damage to the air purifier. Do not block air outlets or intakes.

13. Locate air purifier near the outlet and avoid

using an extension cord.

14. This appliance has a polarized plug (one

blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature.

15. A loose fit between the AC outlet

(receptacle) and plug may cause overheating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.

16. Do not sit, stand or place heavy objects on

the air purifier.

17. Disconnect power supply before servicing.

18. WARNING: To Reduce the risk of fire or

electric shock, do not use this air purifier with any solid-state speed control device.

19.

SAVE THESE

INSTRUCTIONS

QUIETCLEAN® AIR PURIFIERS

Models: HFD-010 Series, HD010 Series, HFD-013 Series, HFD-014 Series, HFD-014-MP2, HFD-015, HFD-110 Series, HD110 Series

The Honeywell Trademark is used by Kaz USA, Inc. under license from Honeywell International Inc.

Honeywell International Inc. makes no representation or warranties with respect to this product.

ifD® Micro-Filter Technology –

The advanced ifD

Micro-filter technology offers the latest advances in air cleaning technology. This filter effectively captures 99% of microscopic particles, 2 microns or larger, from the air that passes through the unit. ifD

stands for Intense Field Dielectric and offers outstanding high efficiency performance while being energy efficient.*

ifD

Micro-Filter –

The ifD

Micro-filter in this product is permanent, and easy to clean. Simply remove the filter and rinse it under the faucet for many years of air cleaning operation. Typically, the filter will only need to be washed once every 3 months.**

Independently Tested and Verified –

This product’s clean air delivery rate has been independently tested and verfied through the AHAM Verifide

™

program. AHAM stands for the

Association of Home Appliance Manufacturers.

Odor-Lock

™

Pre-Filters

The Odor-Lock

™

pre-filters help reduce odors. The filters are made of carbon and zeoliteelements found to break down and adsorb common odors.

FACTS ABOUT YOUR AIR PURIFIER

* From the air that passes through the filter. 99% efficiency at 2 microns or larger.

** Permanent claim is based on normal household usage, washed 4 times per year for 5 years.

HFD-010 HD010 HFD-014

HFD-015 HFD-110 HFD-013

HD110

HFD-014 series, HD010WHS,

HD010LHS, HD010RHS only

PRODUCT ASSEMBLY

INTRODUCTION

Thank you for purchasing the Honeywell QuietClean

High Performance Air Purifier with a breakthrough

technology in air purification. Please read below on how to operate and care for your new air purifier.

Filter

Assembly

ifD® MicroFilters** (2)

Prefilter Frame

Washable Pre-filters (2)

ifD® MicroFilter**

Prefilter Frame

Washable

Pre-filter

(1)

Model HFD-010, HD010, HFD-013, HFD-014 and HFD-015 series only

** ifD® = Intense Field Dielectric Micro-Filtration Breakthrough filter technology

• Outstanding Performance in capturing microscopic particles

• Easy to clean

Odor-Lock™ Pre-filter(1)

HFD-014

HD010WHS,

HD010LHS,

HD010RHS

ONLY

HFD-110 and HD110 Series

SET-UP (ALL MODELS)

• Select a firm, level and flat location. For optimal air flow, locate the unit at least 3 feet (1 M) from the wall or furniture.

• Ensure the exit grille faces away from the closest wall or furniture.

• Ensure no grilles are blocked.

• Plug into a grounded 120V outlet. See IMPORTANT SAFETY INSTRUCTIONS.

ODOR CONTROL (HFD-014, HD010WHS, HD010LHS, HD010RHS ONLY)

Some air purifiers (model HFD-014,HD010WHS, HD010LHS, HD010RHS ONLY) include special odor reducing pre-filters. In order to enjoy the benefits of enhanced odor control, ensure that the Odor-Lock

™

pre-filters

are installed in the unit. (See “Installing The Odor-Lock

™

Pre-filters” on page 7)

For optimal performance, the filters are wrapped in plastic to keep them fresh. If you choose to use the Odor-Lock

™

pre-filters, replacement timing will be approximately every 3 months, depending on use.

Call 1-800-477-0457 or visit www.kaz.com to order your replacement Odor-Lock

™

filters.

OPERATION (HFD-015, HFD-110 and HD110)

• Press the Power ( ) button once. The unit will automatically start at medium power (Fig. 6).

• Select a power level by pressing one of the three power level buttons: High (

), Medium (

) or Low ( ) (Fig. 7). The indicator light

above the selected button will illuminate.

• Press the Power button again to turn off the air purifier.

Timer Operation

• Press the Timer (

) button to select 4, 8 or 12-hour operation (Fig. 8). The timer indicators will illuminate to reflect the selected time. The air purifier will automatically turn off when time runs out.

• The timer can be turned off by repeatedly pressing the Timer (

) button until all of the timer indicator lights go out.

NOTE: Removing the ifD

Micro-filter assembly or turning the

unit off will cancel the Timer function.

OPERATION (HFD-010, HD010, HFD-013 and HFD-014 SERIES)

• Ensure the unit is in the OFF (O) position and then plug into a working outlet.

• Rotate the control knob to the desired speed level: High (

) or

Low (

) (Fig. 5).

• The indicator light will illuminate when the power is on.

• Turn the control knob to the Off (O) position to turn off the air purifier.

Fig. 5

Fig. 7

Fig. 6

Fig. 8

This air purifier is equipped with an electronic filter clean monitor to serve as a convenient guideline for cleaning the ifD

Micro-filter and pre-filter based on the air purifier’s hours of use and operating power level. This is beneficial because a filter’s life depends on the amount of air and contaminants drawn through it. When the Filter Reset button illuminates, it is time to clean the filters and reset the filter clean monitor.

To remove the ifD

Micro-filter:

• Make certain that the air purifier is OFF and the unit is unplugged.

• Push the Filter Release button and then gently lift the filter assembly (Fig. 10a & 10b). The filter assembly will only release if the button is pushed.

• Remove the pre-filter (see “Cleaning the Pre-filter”), and set aside.

To clean the ifD

Micro-filter:

• (Optional) After removing the ifD

Micro-filter from the air purifier, gently run a vacuum cleaner with a nozzle or brush attachment along the filter to pick-up tiny particles (Fig. 11). Repeat on both sides.

If your ifD

Micro-filter appears to have dirt that has not been removed by vacuuming, or if you choose not to vacuum the filter first, please follow the steps below to wash the ifD

Micro-filter.

• Turn the power off and unplug the air purifier.

• Remove the ifD

Micro-filter from the unit.

• You can simply rinse the ifD

Micro-filter under the faucet, or for more thorough cleaning, fill the sink with lukewarm water and add a few drops of mild dish soap (Fig. 12).

• Gently swish the filter in the soap solution to clean.

• Soak the filter for 2-3 minutes. Do not leave for an extended period of time.

• Rinse the filter with clean tap water.

• Shake the filter to remove any excess water.

• Place the filter with the honeycomb side down on a plush towel (Fig. 13).

Filter Clean Indicator Operation (HFD-015, HFD-110 and HD110 Only)

• When the filter clean indicator light illuminates,

(Fig. 9)

it is time to inspect/clean

the ifD

Micro-filter.

• Once you have cleaned the filter, press and hold the Filter Reset button until the LED light goes out.

NOTE: Depending upon your individual usage (environment, hours and power level of operation), you may need to check and clean the filters more or less frequently.

Fig. 10a

Fig. 10b

Fig. 11

Fig. 12

Fig. 13

REMOVING / CLEANING THE IFD® MICRO-FILTER FOR ALL MODELS

FILTER CLEAN INDICATORS HFD-110, HFD-015, HD110

Fig. 9

Filter Reset Button

Indicator Light

•

To replace the permanent, washable pre-filters with the Odor-Lock

™

pre-filters, remove the standard washable

pre-filter assembly by pushing on the top tab (Fig.16).

•

The pre-filter assembly has two pre-filters that will need to be popped out of the pre-filter frame. Hold the frame steady from the side while pushing in the center of each pre-filter from the back side of the frame (Fig.17). This will separate the pre-filter from the frame and you can then pull it completely away from the frame (it will snap out) (Fig.18). Save the permanent washable pre-filters as you may choose to use them in the future.*

•

To insert the Odor-Lock™ pre-filters into the pre-filter frame, line the tabs on the pre-filter up with the frame notches and snap into place (Fig.19).

•

Install the Odor-Lock™ filter assembly by inserting the lower tab of the pre-filter frame into the filter assembly until you hear a “click” (Fig. 20).

•

Align the complete filter assembly with the opening in the unit and insert back into the unit (Fig. 21).

NOTE: The Odor-Lock

™

filters are not washable.

CLEANING THE WASHABLE PRE-FILTER (ALL MODELS)

To remove the pre-filter:

Press the top tab to release the pre-filter from the filter assembly (Fig. 14).

To clean the pre-filter: The particle pre-filter helps pick-up large airborne particles that enter the filter. The pre-filter can be removed and rinsed by hand under warm water (Fig. 15). Let the pre-filter dry completely before inserting it back into the unit.

Some models are shipped with bonus odor control pre-filters that are not washable. After the pre-filters have lost their odor reducing capability over time (approximately 3 months), you can order replacement Odor-Lock

™

pre-filters by calling the Kaz USA, Inc. Consumer Relations Department at 1-800-477-0457.

INSTALLING THE ODOR-LOCK™ PRE-FILTER(S) (HFD-014, HD010WHS, HD010LHS, HD010RHS ONLY)

REMOVING / CLEANING THE IFD® MICRO-FILTER FOR ALL MODELS FILTER (CONTINUED)

Fig. 14

Fig. 16

Fig. 15

Fig. 17

Fig. 18 Fig. 19

Fig. 20 Fig. 21

• Note that the filter may still be discolored even after washing.

This is acceptable and will not affect performance.

• Allow the ifD

Micro-filter to dry for a few hours or overnight.

• When the ifD

Micro-filter is completely dry, place back into the air purifier.

Make sure you insert the filter according to the directional arrows on the filter.

CAUTION:

• Never place a wet ifD

Micro-filter in your air purifier.

• Do not use any solvents, strong cleaning agents or flammable liquids to clean the ifD

Micro-filter.

Please make certain that the unit is OFF and unplugged.

To install the ifD

Filter and

pre-filter:

• Insert the lower tab of the pre-filter frame into the filter assembly (Fig. 22) and press the top tab into the filter assembly until you hear a “click” (Fig. 23).

• Align the filter assembly with the opening in the unit and insert back into the unit (Fig. 24). Press until it is flush and you hear a “click.”

INSTALLING THE FILTERS (ALL MODELS)

Fig. 24

Fig. 23

Fig. 22

NOTE: If you choose to re-insert the standard washable pre-filter in lieu of the Odor-Lock™ pre-filter, they

are removed and inserted in the same way that the Odor-Lock

™

filters are installed. They will not help

reduce odors but will be effective at capturing larger particles like dust, lint and pet fur.

INSTALLING THE ODOR-LOCK™ PRE-FILTER(S) (HFD-014, HD010WHS, HD010LHS, HD010RHS ONLY)

FREQUENTLY ASKED QUESTIONS

How often is cleaning required?

The ifD

filter reset light will illuminate to indicate that the ifD® filter should be cleaned. We recommend

cleaning the filter about once a month depending on the air quality of the room.

I just cleaned my filter but the filter indicator is still showing it is dirty, what’s wrong?

Each time you clean your filter you must reset the filter clean monitor. It is a timer driven monitor to

be used as a guideline, but does not represent the actual amount of dirt in the ifD

filter. With the unit running, press and hold the filter reset button for up to 10 seconds and when you let go, the filter clean monitor should be reset.

Is my Air Purifier considered an ozone generator?

No. Ozone generators produce large amounts of ozone as the primary way to clean the air. The

EPA does not endorse these products because they can cause ozone related health problems. The air purifier does not use ozone as the primary method to clean the air. It cleans the air by using ifD

technology (Intense Field Dielectric) which only generates trace amounts of ozone, substantially below the limits established by the EPA and FDA.

CLEANING AND MAINTENANCE

• Use a clean, dry cloth to wipe the external surfaces of the air purifier. DO NOT USE WATER, GASOLINE, POLISH, OR ANY CHEMICAL SOLUTION.

• The ifD

filter and pre-filter should be cleaned at least once every three months, or sooner depending

on the air quality of the room (See “Removing/Cleaning the ifD

Filter” or “Cleaning the Pre-Filter”

respectively).

NOTE: If you smoke, burn candles or oil lamps in your home, it is recommended that you wash your filter more frequently. When burned in an enclosed space, candles and oil lamps have a tendency to introduce soot into the air.

FILTERS

To order a replacement pre-filter, call us at 1-800-477-0457.

The ionizing process used by the air purifier produces small amounts of ozone as a byproduct. The air purifier complies with U.S. Government limits for acceptable levels of ozone (less than 50 parts per billion by volume of air circulating through the product). People that are extremely sensitive to any ozone emitting products, even trace amounts, should only use True HEPA air purification products.

This product has been California ARB certified to comply with federal ozone emission limits.

IMPORTANT NOTE

YOU SHOULD FIRST READ ALL INSTRUCTIONS BEFORE ATTEMPTING TO USE THIS PRODUCT.

A. This 5 year limited warranty applies to repair or

replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty.

KAZ USA, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

B. At its option, Kaz USA, Inc. will repair or replace

this product if it is found to be defective in material or workmanship.

C. This warranty does not cover the ifD

filter or pre-filter except for material or workmanship defects.

D. This warranty does not cover damage resulting

from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.

E. Return defective product to Kaz USA, Inc. with

a brief description of the problem. Include proof of purchase and a $10 US/$15.50 CAN check or money order for handling, return packing and shipping charges. Please include your name, address and a daytime phone number. You must prepay shipping charges. We strongly recommend tracking or delivery confirmation. Send to:

In U.S.A.:

Kaz USA, Inc. Attn: Returns Department 4755 Southpoint Drive Memphis, TN 38118 USA

In Canada:

Kaz Canada, Inc. Attn: Returns Department 510 Bronte Street South Milton, ON L9T 2X6 Canada

Please go to www.kaz.com and register your product under the Customer Care Center and receive product information updates and new promotional offers.

5 YEAR LIMITED WARRANTY

P/N: 31IM010W190

CONSUMER RELATIONS

Mail questions or comments to:

Kaz USA, Inc. Consumer Relations Dept. 250 Turnpike Road Southborough, MA 01772

Call us toll-free at: 1-800-477-0457 E-mail: consumerrelations@kaz.com

Or visit our website at: www.kaz.com

Please be sure to specify a model number.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY. DO NOT RETURN TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE AIR PURIFIER OR PERSONAL INJURY.

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

LIRE ET CONSERVER CES INSTRUCTIONS DE SÉCURITÉ AVANT D’UTILISER LE PURIFICATEUR D’AIR.

L’utilisation d’appareils électriques nécessite des précautions élémentaires afin de réduire les risques d’incendie, de choc électrique ou de blessures. Parmi les précautions à observer, on compte les suivantes :

1. Lire toutes les instructions avant d’utiliser le

purificateur d’air.

2. Placer l’appareil là où il ne risque pas d’être

renversé par les occupants de la maison.

3. Toujours régler le purificateur d’air à la position OFF et le débrancher quand il ne sert pas.

4. Pour débrancher le purificateur d’air : arrêter le purificateur d’air en appuyant sur le bouton d’alimentation

( )

ou en tournant le bouton à la position d’arrêt

(O)

, puis tenir la fiche et la retirer de la prise de courant. Ne jamais tirer sur le cordon d’alimentation.

5. Éviter d’utiliser tout appareil dont la fiche ou

le cordon d’alimentation est endommagé. Éviter également d’utiliser l’appareil si celui-ci a montré des signes de mauvais fonctionnement, si on l’a laissé tomber ou s’il a été endommagé de quelque façon que ce soit. Tenir le cordon d’alimentation loin des surfaces chaudes.

6. Ne pas utiliser l’appareil en plein air.

7. Ne pas utiliser l’appareil s’il n’est pas

complètement assemblé.

8. Éviter de faire passer le cordon

d’alimentation sous les tapis ou de le recouvrir d’une carpette. Placer le cordon d’alimentation de manière à ce que l’on ne risque pas de trébucher dessus.

9. Ne pas faire fonctionner le purificateur

d’air dans une pièce contenant des gaz ou des vapeurs combustibles, ni dans un environnement riche en oxygène.

10. Ne pas laisser l’appareil à la pluie ni le faire

fonctionner à proximité de l’eau, dans une salle de bains, une salle de lessive ni dans tout autre endroit humide.

11. Le purificateur d’air doit toujours être en

position verticale durant le fonctionnement.

12. S’assurer qu’aucun corps étranger ne

pénètre dans les ouvertures prévues pour la ventilation ou l’évacuation, au risque de recevoir une décharge électrique ou d’endommager l’appareil. Ne pas bloquer les ouvertures servant à l’admission ou à l’évacuation de l’air.

13. Installer le purificateur d’air à proximité

d’une prise de courant et éviter d’utiliser une rallonge.

14. Ce produit est équipé d’une fiche polarisée

(fiche dont l’une des lames est plus large que l’autre). Afin de réduire les risques de choc électrique, cette fiche ne peut être insérée que d’une seule manière dans la prise de courant polarisée. Si la fiche ne s’insère pas complètement dans la prise, tourner la fiche. Si la fiche ne s’insère toujours pas dans la prise, contacter un électricien. NE PAS contourner le dispositif de sécurité que constitue la fiche polarisée.

PURIFICATEUR D’AIR QUIETCLEAN

Modèle de la série

HFD-010, HD010, HFD-013,

HFD-014, HFD-014-MP2, HFD-015, HFD-110

La marque de commerce Honeywell est utilisée par Kaz USA, Inc. avec l’autorisation de Honeywell International Inc.

Honeywell International Inc. ne fait aucune assertion et n’offre aucune garantie en ce qui concerne ce produit.

+ 23 hidden pages

Honeywell HD010, HD110 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual