Honeywell HCU484, HCU484X User Manual

Download

Page 1

HCU484/X

Ultra Wide Dynamic

Day/Night Body Camera

User Guide

Document 900.0418 – 10/06 – Rev 1.01

HCU484 HCU484X

NTSC

PAL

Page 2

Rev 1.01 ii Document 900.0418

10/06

Revisions

Issue Date Revisions

1.00 08/06 New document

1.01 10/06 Reordered WDR Presets, page 8.

Page 3

Rev 1.01 iii Document 900.0418

10/06

Warnings

Installation and servicing should be performed only by qualified technicians to conform to all local codes and to maintain your warranty.

WARNING! The use of a CSA Certified/UL

Listed Class 2 power supply is required to ensure compliance with electrical safety standards.

WEEE (Waste Electrical and Electronic Equipment). Correct

disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

Explanation of Graphical Symbols

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER.

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THE UNIT.

THIS SYMBOL INDICATES THAT IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS ACCOMPANY THIS UNIT.

CAUTION

Page 4

Regulatory Notice

INTENDED PURPOSE:

SECURITY AND SURVEILLANCE CCTV APPLICATIONS. The product must be installed and maintained in accordance

with good installation practice to enable the product to function as intended and to prevent problems. Refer to Honeywell Video Systems for installation guidance.

Manufacturer’s Declaration of Conformance

FCC Statement (U.S.A.)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada Notice

This digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique toutes les exigences du Règlement sur la matériel brouilleur du Canada.

The CE mark on the product indicates that the system has been tested to, and conforms with, the provisions noted within the 89/336/EEC Electromagnetic Compatibility Directive.

Rev 1.01 iv Document 900.0418

10/06

Page 5

Rev 1.01 Document 900.0418

10/06

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installing the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Adjusting the Flange Back Focus . . . . . . . . . . . . . . . . . . 2

Setting the Signal Format . . . . . . . . . . . . . . . . . . . . . . . . 3

Connecting Monitor and Power. . . . . . . . . . . . . . . . . . . . 3

Remote Control Connections . . . . . . . . . . . . . . . . . . 4

Single Camera Connection . . . . . . . . . . . . . . . . . . . . 5

Multiple Camera Connections . . . . . . . . . . . . . . . . . . 5

Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Making Final Adjustments . . . . . . . . . . . . . . . . . . . . . . . . 5

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

OSD menu controls . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Navigating Through the Menus . . . . . . . . . . . . . . . . . 6

OSD Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . 7

Configuring the WDR Presets . . . . . . . . . . . . . . . . . . . . . 8

Optimizing the Camera Setup . . . . . . . . . . . . . . . . . . . . . 9

Setting the Camera Image Properties . . . . . . . . . . . . . . 12

Setting the Day/Night Control . . . . . . . . . . . . . . . . . . . . 13

Restoring Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Page 6

Page 7

Rev 1.01 1 Document 900.0418

10/06

Introduction

Honeywell’s HCU484 Ultra Wide Dynamic Day/Night Series camera uses Digital Pixel System®

Image Capture technology to convert images into a digital format within each individual pixel immediately after the image has been captured. This camera is ideal for complex light environments; for example, lobbies, entrances, and outdoor areas.

An intuitive menu and Graphical User Interface (GUI) helps you quickly set up the camera to ensure the best picture quality for your unique environment. The HCU484 requires little or no adjustment after initial installation.

Features

• 1/3” Wide Dynamic Digital Imager

• 32-bit digital processing

• Independent per-pixel exposure

• Dynamic range: 102 dB typical, 120 dB maximum

• 50/60 FPS progressive video capture

• 0.4 lux @ F1.2

• 480 TV lines of resolution

• 12 VDC or 24 VAC with line lock

• Supports DC (Direct Drive) and Manual Iris lenses

Package Contents

Check that the items received match those listed on the order form and packing slip. The HCU484 camera packing box should include, in addition to this User Guide, one HCU484 (NTSC) or HCU484X (PAL) camera.

If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service.

1.Digital Pixel System® is a registered trademark of Pixim Inc.

Page 8

Rev 1.01 2 Document 900.0418

10/06

Installation

Installing the Lens

Note You must use an Auto Iris lens to take full

advantage of this camera’s wide dynamic performance.

Note The camera auto senses whether an Auto Iris

lens or a Manual Iris lens is attached.

The HCU484 Series camera is factory configured for a CSmount lens.

Follow Figure 1 to attach a customer supplied lens, screw the lens

! into the front of the camera body ".

Figure 1 CS Mount

Figure 2 Pin Definitions

Adjusting the Flange Back Focus

The back focus adjustment is accessible at the front end of the camera housing to adjust the back focal length or picture focus.

1. Loosen the setscrews with a Phillips screwdriver.

2. Adjust the focus ring to focus the picture.

3. Retighten the setscrew.

Setscrew

Pin DC Lens

1CTRL 2CTRL + 3DRV + 4DRV -

123

Page 9

Rev 1.01 3 Document 900.0418

10/06

Setting the Signal Format

Figure 3 Camera Rear View

Set the signal format switch (see Figure 3) to:

NTSC for North America PAL for International

Connecting Monitor and Power

Note Check the power source from the external

power supply before applying power to the camera.

1. Connect the VIDEO connector on the rear of the camera

to the video-in connector on your monitor.

2. Connect the camera to a 12 VDC or 24 VAC power supply

(appropriate to your installation). Use a screwdriver to first loosen the ~AC24V/DC12V terminal screws on the terminal block.

Figure 4 Video Connections

Note To ease installation, the terminal block can be

removed. The power connections of the removable terminal block are not polaritysensitive. Connect either power lead to either connector terminal.

3. Secure the power leads by retightening the terminal

screws until snug.

Set signal format

LENS

ENTER

VIDEO

NTSC PAL

12VDC 24VAC

RX+RX

Power LED

Page 10

Rev 1.01 4 Document 900.0418

10/06

4. Plug the power supply into an appropriate power source. The power LED illuminates to show that the camera is receiving power. If it does not illuminate, check the removable terminal block connections and the power source.

Remote Control Connections

The HCU484 Series camera can be controlled remotely using an RS485 connection. Figure 5 shows a remote control connection using a Honeywell HJZTP keyboard controller.

Figure 5 Camera Connection Via RS485

HJZTP Keyboard Control (Optional)

To program the HCU484 menu using the HJZTP keyboard controller, first select the Camera ID on the HJZTP, then:

• Press 90 + Preset to access the menu.

• Rotate the Joystick Up, Down, Left, and Right to navigate through the menu and submenus.

• Press Iris Open to enter a screen or select a menu option (similar to ENTER on the camera OSD).

LENS

ENTER

VIDEO

NTSC PAL

12VDC 24VAC

RX+RX

Cable Legend

White/orange TRx+ Orange TRx-

Connector Legend

1RX+ 2RX3Power 1 4 Power 2

Joystick

Numerical keypad

Preset

Iris Open

Page 11

Rev 1.01 5 Document 900.0418

10/06

Single Camera Connection

Note Do not remove the 120 Ohm termination

resistor provided with the camera.

Multiple Camera Connections

For installations of more than one HCU484 camera in a daisychain configuration, keep the 120 Ohm termination resistor (provided with the camera) only in the last camera in the series (see Figure 6). For all other cameras in the daisychain, remove the 120 Ohm termination resistor.

Note Up to 254 cameras can be daisychained.

Figure 6 Multiple Camera System

Mounting the Camera

Mounting points are provided on the top and bottom of the camera and are used to mount the camera on a bracket or tripod. They are designed to accept standard sized mounting bolts. The mounting bracket must be capable of supporting the weight of the camera and its lens.

Caution Some installation codes dictate that the

mounting bracket must be capable of supporting up to four times the combined weight of the camera and lens.

Making Final Adjustments

Adjust the focus in your field of view; that is, until you see a clear image. If necessary, adjust the brightness using the OSD menu controls (see >BRIGHTNESS on page 12). Confirm the exposure on the monitor screen.

Last camera in daisychain must have the 120 Ohm terminatio

resistor installed.

1 - 254 cameras

Remove the 120 Ohm termination resistor from all cameras except the last one.

HJZTP Keyboard

Page 12

Rev 1.01 6 Document 900.0418

10/06

Programming

On-Screen Display

Use the OSD (On-Screen Display) to program the camera.

OSD menu controls

Figure 7 Menu Controls

Navigating Through the Menus

Press (the middle button) for two seconds to enter the menus.

Note Menu items followed by … (for example, WHITE

BALANCE …) indicate submenus. Select the menu, then press to enter the submenu.

To leave the screen and return to the previous menu, select PREVIOUS PAGE, and then press .

To save your changes, select SAVE & EXIT, and then press

. Your settings remain in effect when power is turned off,

then on again.

LENS

ENTER

VIDEO

NTSC PAL

12VDC 24VAC

RX+RX-

➀

• Press and hold ENTER 2 seconds to access MAIN MENU

• Press to enter a screen or select a menu option

!, "

Move horizontally to and between menus and options

#, $

Move vertically to and between menus and options

“…” indicates submenus

➀

Page 13

Rev 1.01 7 Document 900.0418

10/06

When no buttons are pressed, the menu display turns off automatically after 5 minutes.

OSD Menu Structure

The HCU484 menu system consists of four setup menus for easy camera programming.

Figure 8 Menu Structure

Select a menu, then press the middle button to enter the submenu

Change the status using the !, " arrows

CAMERA SETUP .. VIEWING .. WDR PRESETS .. DAY/NIGHT SETUP .. VERSION INFO .. RESTORE DEFAULTS <NO> EXIT EXIT W/O SAVE.

DIG SLOW SHUTTER .. SYNC MODE AGC .. WHITE BALANCE RS485 SETUP .. AI THOLD

FLIP ID DISPLAY .. SHARPNESS BRIGHTNESS RESOLUTION COLOR ADJ.

PRESETS FLUORESCENT

D/N CONTROL .. NIGHT MODE

NO YES

SAVE & EXIT EXIT W/O SAVE

CAMERA VIEWING WDR

PRESETS

RESTORE

SETUP

DEFAULTS

Menu:

FW Rev:

VERSION

EXIT

DAY/NIGHT SETUP

INFO

Page 14

Rev 1.01 8 Document 900.0418

10/06

Configuring the WDR Presets

Select the appropriate camera mode for the lighting conditions.

<CUSTOM> Opens the CUSTOM screen where you

can adjust the limits of the wide dynamic range by moving the cursor.

Note Observe the results on the video

monitor for the best results.

>WDR LIMIT Adjust the dynamic range to change the

camera’s light optimization. Reduce the level to lower the dynamic range. Adjust the slider from 0 to 36 (default is 20).

<AES> The AES (Automatic Electronic Shutter)

feature compensates for excessive light levels by automatically adjusting the shutter speed of the camera. Select from:

HIGHLIGHTS for optimum exposure of bright areas of the scene.

SHADOWS for optimum exposure of dark areas of the scene.

WDR PRESETS

INDOOR LOADING DOCK GAMING LICENSE PLATE OUTDOOR CUSTOM ATM LOBBY

WDR PRESETS

CAMERA SETUP .. VIEWING .. WDR PRESETS .. INDOOR> DAY/NIGHT SETUP .. VERSION .. RESTORE DEFAULTS EXIT SAVE & EXIT

WDR PRESETS

PRESETS .. <CUSTOM.> FLUORESCENT OFF PREVIOUS PAGE

WDR Preset Area of Interest WDR Exposure

INDOOR Full scene Wide Highlights LOADING DOCK Center scene Wide Highlights GAMING Full scene spot glare Medium Highlights LICENSE PLATE Full scene spot glare Medium Shadows OUTDOOR Full scene Ultrawide Highlights ATM Center scene Ultrawide Shadows LOBBY Center scene Wide Shadows

The table below explains the Preset options on the WDR PRESETS menu. Double-click a Preset to display a read-only screen showing the factory settings. INDOOR is the default.

CUSTOM

WDR LIMIT 36 0 36 AES SHADOWS PREVIOUS PAGE .

Page 15

Rev 1.01 9 Document 900.0418

10/06

Optimizing the Camera Setup

Note This menu is for advanced users only.

The table below explains the options on the CAMERA SETUP menu. Each selection on this menu takes you to a separate screen, as described below.

DIG SLOW SHUTTER (Digital

Slow Shutter)

Select a shutter speed, from x2 to x32. Notice that the AGC value changes accordingly.

> CUSTOM. Opens the SLOW SHUTTER SETUP

menu where you select the optimum exposure adjustment. Shutter mode options are:

SHUT PRI (Priority) to select the sensitivity LIMIT from 0 to 60 (26 is the default), or the sensitivity THRESHOLD from 22 to 34 (22 is the default).

GAIN PRI (Priority) to adjust the noise LIMIT in the image, from 0 to 60 (26 is the default), or adjust the gain THRESHOLD from 28 to 42 (28 is the default).

MANUAL to manually set the sensitivity LIMIT the sensitivity from 0 to 60 (26 is the default).

>SYNC Synchronize the vertical interval sync

pulse of your camera with other equipment to reduce the effect of picture roll on the monitor. Select either:

<INTERNAL> (default) for cameras using DC power or when line lock is not required, or

<LINE LOCK> to open the Line Lock screen where you can adjust the Vertical Phase (V PHASE) from 0 to 624 (519 is the default).

CAMERA SETUP

DIG SLOW SHUTTER X2 .. SYNC MODE .. LL .. AGC 26 dB WHITE BALANCE .. RS 485 SETUP .. AI THOLD -18 -42 60

SLOW SHUTTER SETUP

SHUT MODE SHUT PRI .. PREVIOUS PAGE .

AUTO SHUTTER--SHUT PRI

LIMIT

026 60

THRESHOLD

22 22 34

PREVIOUS PAGE .

MANUAL SHUTTER

LIMIT 26 0 60 PREVIOUS PAGE .

LINE LOCK

V PHASE

0519624

PREVIOUS PAGE .

Page 16

Rev 1.01 10 Document 900.0418

10/06

>AGC The AGC (Automatic Gain Control)

setting affects the day/night threshold. A higher AGC value results in the camera switching from day to night mode at lower levels. While observing a video monitor, adjust the noise in the image, from 0 dB to 36 dB.

Opens the WHITE BALANCE menu where you set how the camera tracks to accept different lighting conditions within the color range of 2000K to 11000K.

The ATW Normal (default) and ATW Desat options open the WHITE BALANCE LIMITS screen where you set the Low and High white balance limits (2100K to 8800K) while observing the video monitor.

ATW Desat is useful for low light conditions.

<AWB> Opens the PUSH AWB CONFIRM

screen where you save your AWB settings to have them take effect, or select CANCEL.

Auto white balance ensures that color integrity is maintained.

Caution Selecting Save will

overwrite all previous settings.

<MANUAL …> Opens the MANUAL WHITE

BALANCE menu where you adjust

the color settings while observing the scene in the video monitor. Options are:

<KELVIN> Move the cursor to set the TINT, from 2K to 11K (default is

2900). <R/B> Adjust the RED and BLUE

settings, from -20 to 20. The default red is -18 and the default blue is 13.

Use this feature when:

• Non-standard lighting exists or color lighting temperature exceeds the range of the camera.

• A significant part of the scene contains a single color or a completely red or blue background.

WHITE BALANCE LIMITS

LOW LIMIT

2K 2100 5.5K

HIGH LIMIT

5.5K 8800 11K

PREVIOUS PAGE .

MANUAL WHITE BALANCE

ADJ MODE <R/B ..> PREVIOUS PAGE .

R/B ADJUST

RED -18 -20 20 BLUE 13 -20 20 PREVIOUS PAGE .

Page 17

Rev 1.01 11 Document 900.0418

10/06

<ATW Xtnd> Automatic Tracking White Balance

(Extended Range). Continuously monitors the color temperature while an internal micro controller sets the white balance. Select this mode when the scene illumination varies between indoor scenes and outdoor scene lighting. Operating color temperature range is 2000K to 11000K.

>ADVANCED WHITE BAL ..

Opens the ADVANCED WHITE BALANCE menu where you can

adjust the magenta or the white balance bias. Options are:

<MGNTA CTRL>. Select <OFF> <ON> <CUSTOM> to open the MAGENTA CONTROL screen and, while

observing the video monitor, adjust the level, from 0 to 100 (5 is the default).

<WB BIAS> to adjust the level from

-2K to 2K (0 is the default).

>RS485 SETUP .. Opens the RS485 SETUP screen

where you can select from the supported protocols and enter an RS485 Camera ID #. Options are:

<PROTOCOL> <Diamond> (default) <Pelco D>

<CAMERA #:> Selectable from 1 to 255 (1 is the default).

>AI THOLD Adjust the Automatic Iris (AI)

threshold, from -42 to 60 (default is -18).

Note When using a manual iris

lens, set the AI threshold to -42 (recommended).

Note The AI threshold is factory set

to -18 for all WDR presets.

ADVANCED WHITE BALANCE

MGNTA CTRL OFF WB BIAS

-2K 0 2K

PREVIOUS PAGE .

RS485 SETUP

PROTOCOL <Diamond> CAMERA #: PREVIOUS PAGE .

Page 18

Rev 1.01 12 Document 900.0418

10/06

Setting the Camera Image Properties

The table below explains the options on the VIEWING menu.

>FLIP Select either:

<ON> to reverse the image

horizontally on the video monitor, or

<OFF> (default)

> ID DISPLAY. Select ON to open the CAMERA ID

SETUP screen where you can add a CAMERA ID (title) of up to 8

characters. Move the cursor (>) to CAMERA ID,

then press . The first character appears. Press !, or " to change the character, then press to move to the next character.

When you are satisfied, press #, or$ and move the cursor to another item.

>ID POSITION Select where you want the Camera ID

to appear on the monitor screen Select from the list:

<UP-LEFT>, <UP-CENTER>, <UPRIGHT>, <DOWN-LEFT>, <DOWNRIGHT>

>SHARPNESS Select the level of sharpness of the

image. Choices are:

<NORMAL> (default) <SHARP> <SOFT>

>BRIGHTNESS While observing the video monitor,

move the cursor to adjust the overall brightness level, from 80 to 130 (110 is the default).

RESOLUTION Select the camera resolution. Choices

are:

<NORMAL> (default) <HIGH>

VIEWING

FLIP OFF ID DISPLAY <OFF> SHARPNESS NORMAL BRIGHTNESS 110 80 130 RESOLUTION NORMAL COLOR ADJ. 0 -8 8 PREVIOUS PAGE .

CAMERA ID SETUP

CAMERA ID ID POSITION UP-LEFT PREVIOUS PAGE .

➀

Page 19

Rev 1.01 13 Document 900.0418

10/06

Setting the Day/Night Control

The table below explains the options on the DAY/NIGHT SETUP menu.

Restoring Settings

On the main MENU, select RESTORE DEFAULTS, then YES followed by ENTER (middle button). This reloads the factory default camera settings.

Caution This action replaces all custom settings.

>COLOR ADJ While observing the video monitor,

move the cursor to adjust the color saturation, from -8 to 8 (0 is the default).

>D/N CONTROL Select either:

<AUTO> (default), or <OFF> camera stays in color mode.

Note This setting is dependent on

the AGC setting. (See “>AGC” on page 10.)

>NIGHT MODE The NIGHT MODE screen determines

whether monochrome (B/W) or color is present in the video. Options are:

<B/W> suppresses all color, including color burst, present in the video.

<B/W + CLR> (default) = B/W with color burst <COLOR> the camera never switches to B/W in night mode.

DAY/NIGHT SETUP

D/N CONTROL OFF NIGHT MODE COLOR PREVIOUS PAGE .

CAMERA SETUP … VIEWING … WDR PRESETS <Custom> DAY/NIGHT SETUP … VERSION … RESTORE DEFAULTS <YES> EXIT

Page 20

Rev 1.01 14 Document 900.0418

10/06

Solutions

Frequently Asked Questions

The image appears to have a white cast and looks soft. How can I reduce this effect?

Select the Wide Dynamic Preset that gives you the best picture for your scene. If you still have the problem, go to the CUSTOM menu and reduce the dynamic range slider to a lower value. Using the VIEWING menu, set the Resolution to High and Sharpness to Normal or to Sharp.

The image on a standard high resolution color camera appears to have brighter colors. How do I make the HCU484 have a similar look to a traditional CCTV camera?

Select the Wide Dynamic Preset that gives you the best picture for your scene. If you still have the problem, go to the VIEWING menu and increase the color saturation to a higher value.

If this happens …

It could be caused by …

Try this …

No picture on monitor

Lens cap still in place

Remove lens cap.

No power to camera

Check that the power LED on the camera is lit. If not lit, check the camera power supply.

Monitor not functioning

Connect a test monitor to the VIDEO Out connection and check for a local video signal.

A faulty coaxial cable

Check cable.

Poor picture quality

Dirty camera lens

Clean camera lens.

Monitor not configured properly

Check the monitor settings. Ensure termination at

monitor is correct. Check cable connections.

Camera not focused

Set the lens focus. Refer to the instructions that came with your lens.

For service and support

Refer servicing to qualified personnel or contact Honeywell Technical Support at +1.800.796.CCTV for assistance.

Page 21

Rev 1.01 15 Document 900.0418

10/06

If I select a WDR preset and change the AGC value, when I go back to the WDR preset, it has changed to “Custom”. Has my preset been changed or erased?

The WDR presets set the dynamic range, the exposure, sharpness and the AGC level. Changing any of these will change the WDR preset to Custom. When you saw the Custom setting, the preset that you selected was still loaded, except that the AGC had changed, thus customizing your setup. This camera function allows any WDR preset to be loaded into custom so that you can modify the dynamic range and exposure of the underlying preset.

There are seven WDR presets in the camera. How do I know which one to use for my scene?

The WDR presets consist of three main types—centerweighted scene, full scene, and full scene with spot glare. Depending on the scene, you can narrow down your choice to the presets within each of these groups. Most applications can use the full scene WDR preset—INDOOR or OUTDOOR—as these are optimized for general lighting conditions (General Scenes in the first generation HCCWD484 wide dynamic camera).

Other applications in which the area of interest is primarily in the center of the scene should use the ATM, LOADING DOCK or LOBBY WDR presets.

• ATM is optimized to render proper exposure of faces when the person is backlit by the sun, while still allowing the ability to make out a person standing behind the person using the ATM machine.

• LOADING DOCK is for areas with a tall vertical opening and walls on either side.

• LOBBY is for areas with large windows across the scene.

However, depending on your lighting conditions and angle of view, a different preset may render a better picture for your scene.

For scenes in which there are hot spots of illumination that can occur anywhere in the scene and you need to see detail of objects near these hotspots, the Full scene with spot glare presets—GAMING and LICENSE PLATE—will likely offer the best picture quality for seeing the objects of interest.

• GAMING is optimized to allow the reading of cards when the card is in a hotspot and is producing glare.

• LICENSE PLATE is optimized to allow the viewing of the front license plate when the headlights are shining into the camera.

Page 22

Rev 1.01 16 Document 900.0418

10/06

Specifications

HCU484 HCU484X

Operational

Video Standard: NTSC,

525 lines, 2:1 interlace

PAL, 625 lines,

2:1 interlace Scanning System: Progressive Image Sensor: 1/3” WDR digital image device Number of Pixels: 720 (H) x 540 (V) Minimum Illumination: 0.4 lux @ F1.2 Horizontal Resolution: 480 TVL Video Output: 1 V p-p, 75 Ohms Sync System: 12 VDC: Internal

24 VAC: (Line lock) S/N Ratio: 53 dB typical Auto Gain Control

(AGC)

Auto (0–36 dB maximum)

Automatic Electronic Shutter

1/60 1/100,000 sec

1/50 -

1/100,000 sec Lens Iris Control DC Drive White Balance: AWB/ATW/ATW Xtnd/Manual Line Lock Phase Adjust: Adjustable line lock

vertical phase

Electrical

Input Voltage: 12 VDC/24 VAC Input Range: 11 - 16 VDC, 17 - 28 VAC Surge Suppression: 1.5 kW transient Power Consumption: 2.5 W Temperature:

Operating: Storage:

14°F to 122°F (-10°C to 50°C)

-4°F to 140°F (-20°C to 60°C)

Mechanical

Dimensions (W x H x L): 2.68 in. x 2.46 in. x 3.86 in.

(66 mm x 63 mm x 98 mm) Weight: 1.1 lb (.5 kg) Camera only Housing Construction: Extruded aluminum housing Housing Finish: Powder coated Lens Mount: CS adjusting mounting ring Video Output: BNC connector Power Input: Removable screw

terminal block

Page 23

Page 24

Honeywell Video Systems (Head Office)

2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA

www.honeywellvideo.com

℡

+1.800.796.2288

Honeywell Security Australia Pty Ltd.

Unit 5, Riverside Centre, 24-28 River Road West Parramatta, NSW 2150, Australia

www.ademco.com.au

℡

+61.2.8837.9300

Honeywell Security Asia Pacific

33/F Tower A, City Center, 100 Zun-Yi Road Shanghai 20051, China

www.security.honeywell.com/cn

℡

+86.21.2527.4568

Honeywell Security Asia

Flat A, 16/F, CDW Building, 388 Castle Peak Road Tsuen Wan, N.T., Hong Kong

www.security.honeywell.com/hk

℡

+852.2405.2323

Honeywell Security France

Parc Gutenberg, 8 Voie La Cardon 91120, Palaiseau, France

www.honeywell.com/security/fr

℡

+33.1.6932.1090

Honeywell Security Italia SpA

Via Treviso 2 / 4 31020 San Vendemiano Treviso, Italy

www.honeywell.com/security/it

℡

+39.04.38.36.51

Honeywell Security España

Mijancas 1. 3

Planta P.Ind. Las Mercedes 20822 Madrid, Spain

www.security.honeywell.com/es

℡

+34.902.667.800

Honeywell Security Nederland

Netwerk 121 1446 WV Purmerend, Netherlands

www.SecurityHouse.nl

℡

+31.299.410.200

Honeywell Video Systems UK Ltd.

Aston Fields Road, Whitehouse Ind Est Runcorn, Cheshire, WA7 3DL, UK

www.honeywellvideo.com

℡

+0844.8000.235

Honeywell Security South Africa

Unit 6 Galaxy Park, 17 Galaxy Avenue, Linbro Park, P.O. Box 59904 2100 Kengray, Johannesburg, South Africa

www.honeywell.co.za

℡

+27.11.574.2500

Honeywell Security Germany

Johannes-Mauthe-Straße 14 D-72458 Albstadt, Germany

www.honeywell.com/security/de

℡

+49.74 31.8 01.0

Honeywell Security Poland

Chmielewskiego 22a, 70-028 Szczecin, Polska

www.ultrak.pl

℡

+48.91.485.40.60

Honeywell Security Czech Republic

Havránkova 33, Brno Dolní Heršpice, 619 00, Czech Republic

www.olympo.cz

℡

+420.543.558.111

Honeywell Security Slovakia Republic

Vajnorskà 142, 83104 Bratislava Slovakia

www.olympo.sk

℡

+421.2.444.54.660

© 2006 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

www.honeywellvideo.com

+1.800.796.CCTV (North America only)

HVSsupport@honeywell.com

Document 900.0418 10/06 Rev 1.01