Page 1
®
EQUIP
Series
True Day/Night
Network Box Camera
NTSC / PAL
HCD5HIH HCD5HIHX
HCD5MIH HCD5MIHX
HCD5WIH HCD5WIHX
Reference Guide
Document 800-07067V4 – Rev A – 11/2011
Page 2
Page 3
Reference Guide
Page 4
Revisions
Issue Date Revisions
V2 A 11/2011 Changed 800-07067V1from a User Guide exclusively for HCD5MIH/X. Added the
HCD5HDIH(X) and HCD5MWIH(X) cameras to this User Guide.
Added a note in Chapter 2 advising that the camera should not be connected to two
different power sources at the same. Changed the number of users that can be
logged on at the same time. Changed the length of time required to hold down the
reset button. Added a note in the IP installation section suggesting that all Norton
AntiVirus software be disabled before installing the IP software.
Added the information for installing the Honeywell IP Utility on Windows 7. And added
Frame Rate to the list of available priority settings in the Compression Settings
section.
V3 A 11/2011 Removed sentence in Specifications which states that only 4 users can log on at a
time. Removed notes throughout that referred to a limited number of users that can
be logged on at a time. Updated the System Requirements. Added the step for
Enabling Microsoft .NET Framework 3.5 to the Install Honeywell IP Utility Software
section. Expanded on the Disable User Account Control section. Added WDR and
LDC to the Auto Exposure Settings table. Changed the Immunity Regulatory
specification from EN 50024 to 50130-4.
V4 A 11/2011 Corrected the description of the Alarm I/O and Audio I/O connectors in the
specifications for HCD5MIH(X) and HCD5WIH(X).
4
Page 5
Contents
Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Overview of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Manufacturer’s Declaration of Conformance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Warranty and Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2 Installation and Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Overview of the Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Selecting the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Adjusting the Back Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Mounting the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Restoring Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3 Installing the Honeywell IP Utility and Web Client Software . . . . . . . . . . . . . . . . . . . . 25
About the Honeywell IP Utility and Web Client. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
About the Honeywell IP Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
About the Web Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
User Profiles: Honeywell IP Utility and Web Client . . . . . . . . . . . . . . . . . . . . . . . . 26
Step 1: Confirm Your System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Step 2: Install the Honeywell IP Utility Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Downloading the EQUIP Series Installation Guides . . . . . . . . . . . . . . . . . . . . . . . 29
IStep 3: Log Onto the IP Utility and Discover Network Devices . . . . . . . . . . . . . . . . . . . . . . 29
Step 4: Connect to a Device and Configure Network Settings . . . . . . . . . . . . . . . . . . . . . . 31
Connecting to or Disconnecting from Devices . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Configuring the IP Network Settings Automatically or Manually . . . . . . . . . . . . . . . . . 32
Interfacing with the EQUIP PSIA Device Via a Network Video Recorder . . . . . . . . . . . . 35
Document 800-07067V4 Rev A 5
11/2011
Page 6
Contents
Step 5: Launch the Web Client to View Live Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Uninstalling IP Utility, Bonjour or the ActiveX Plug-in Software . . . . . . . . . . . . . . . . . . . . . .37
Uninstalling IP Utility Using the Start Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Uninstalling IP Utility or IP ActiveX Using the Control Panel . . . . . . . . . . . . . . . . . . . 37
4 IP Camera Web Client. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
User Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Logging On and Off the IP Web Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Launching the Web Client from IP Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Logging Onto the Web Client from Internet Explorer . . . . . . . . . . . . . . . . . . . . . .42
Logging Out of the Web Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Navigating the Web Client User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Live View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Taking a SnapShot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Configuring IP and Firmware Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Resetting the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Compression Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Primary Stream Video Codec Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Secondary Stream Video Codec Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Statistics: Received Bit Rate and Frame Rate . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Camera Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Auto Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
White Balance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Video Analytics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Sabotage Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Configuring Video Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Alarm and Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Alarm Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Appendix A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Problem: Failure of IP Utility Software Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Problem: Web Client Does Not Display the Expected Video . . . . . . . . . . . . . . . . . . . . . . . 62
Problem: Cannot Connect to a Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Appendix B HCD5HIH Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Appendix C HCD5MIH Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Appendix D HCD5WIH Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Appendix E Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6
Page 7
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Figures
Figure 1-1 Camera Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 2-1 Back Focus Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 2-2 Camera Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 2-3 Camera Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 2-4 Alarm Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 2-5 Normal Alarm States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 2-6 Alarm Output Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 3-1 Accessing Your Installation Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 3-2 Honeywell IP Utility Log On Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 3-3 Honeywell IP Utility User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 3-4 Setting the IP Network Settings Automatically or Manually . . . . . . . . . . . . . . . . . . 33
Figure 3-5 ActiveX Prompt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 3-6 Web Client Interface After Logging On . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 4-1 Launching the Web Client from the IP Utility . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 4-2 Web Client Window Layout: Administrator Log On . . . . . . . . . . . . . . . . . . . . . . 43
Figure 4-3 Web Client: Administrator User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 4-4 Web Client: Guest User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 4-5 Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 4-6 IP and Firmware Settings: Device Information Tab . . . . . . . . . . . . . . . . . . . . . . 46
Figure 4-7 Compressions Settings Tab: Primary Stream . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 4-8 Primary Stream Video Codec Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 4-9 Secondary Stream Video Codec Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 4-10 Video Codec Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Figure 4-11 Camera Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 4-12 Video Analytics Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 4-13 Tamper Detection Settings on the Video Analytics Tab. . . . . . . . . . . . . . . . . . . . 55
Figure 4-14 Video Analytics Alarm Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 4-15 Video Analytics: Defining a Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 4-16 Audio and IO Settings Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 4-17 Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure A-1 Limited or No Connection Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure B-1 Camera Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Figure C-1 Camera Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Figure D-1 Camera Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Document 800-07067V4 Rev A 7
11/2011
Page 8
Figures
8
Page 9
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Tables
Table 1-1 Network Cameras Model Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 3-1 User Profiles for Honeywell IP Utility and the Web Client . . . . . . . . . . . . . . . . . . . 26
Table 3-2 PC Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 3-3 Items Installed On Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 3-4 IP Network Device Setting Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 4-1 User Roles and Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 4-2 Tabs/Views in the Web Client Application . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 4-3 Video Streaming Resolutions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 4-4 Compression Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 4-5 Auto Exposure Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 4-6 White Balance Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 4-7 Blur Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 4-8 Blinding Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 4-9 Scene Change Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Document 800-07067V4 Rev A 9
11/2011
Page 10
Tables
10
Page 11
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
About This Document
This document introduces the Honeywell HCD5 Series of High Resolution True Day/Night
Network Box Cameras. This series includes the following cameras:
• HCD5HIH(X) 1080p True Day/Night Network Box Camera
• HCD5MIH (X) 720p True Day/Night Network Box Camera
• HCD5WIH(X) 720p Wide Dynamic True Day/Night Network Box Camera
This document explains how to install, configure and operate the camera in a network
environment. This document is intended for system installers, administrators, and
operators.
Overview of Contents
This document contains the following chapters and appendixes:
• Chapter 1, Introduction, introduces the Honeywell network box camera and gives a
functional overview of its components.
• Chapter 2, Installation and Setup, provides procedures for installing cameras, lens
adjustment, and setting up a network camera environment.
• Chapter 3, Installing the Honeywell IP Utility and Web Client Software, describes how
to install and use the Honeywell IP Utility and web client software.
• Chapter 4, IP Camera Web Client, describes how to use the web client application to
view video and configure the available settings for the network camera.
• Appendix A, Troubleshooting, lists common problems encountered when setting up
the network camera.
• Appendix B, HCD5HIH Specifications, provides specifications for HCD5HIH(X)
cameras.
• Appendix C, HCD5MIH Specifications, provides specifications for HCD5MIH(X)
cameras.
• Appendix D, HCD5WIH Specifications, provides specifications for HCD5WIH(X)
cameras.
•The Glossary explains terms and initializations used in this guide.
•The Index provides quick access to commonly searched terms.
Document 800-07067V4 Rev A 11
11/2011
Page 12
About This Document
Cautions and Warnings
Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
WARNING! 24V AC models require the use of CSA Certified/UL Listed
Class 2 power adapters to ensure compliance with
electrical safety standards. Power over Ethernet (PoE)
should meet the IEEE 802.3 af PoE standard.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this
product (applicable in the European Union and other European countries with
separate collection systems). This product should be disposed of, at the end of
its useful life, as per applicable local laws, regulations, and procedures.
Caution When powering the camera from 24V AC, a UPS source should
be considered to ensure satisfactory performance.
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the
limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
12
Page 13
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference. For example, try reorienting or relocating the receiving antenna,
increasing the separation between the equipment and receiver, or connecting the
equipment to an outlet on a different circuit.
Caution Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
North America
The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No.
60950-1.
Europe
The manufacturer declares that the equipment supplied with this guide is compliant with
the essential protection requirements of the EMC directive 2004/108/EC and the General
Product Safety Directive 2001/95/EC, conforming to the requirements of standards EN
55022 for emissions, EN 50130-4 for immunity, and EN 60950-1 for Electrical Equipment
safety.
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty
period Honeywell will repair or replace, at its sole option, free of charge, any defective
products returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer
Service at 1.800.796.CCTV for assistance or to request a Return Merchandise
Authorization (RMA) number.
Be sure to have the model number, serial number, and the nature of the problem available
for the technical service representative.
Document 800-07067V4 Rev A 13
11/2011
Page 14
About This Document
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped
to Honeywell without a clearly identified Return Merchandise Authorization (RMA)
number may be refused.
14
Page 15
1
Introduction
Reset button restores
factory default settings
CS lens mount
Lens connector for
DC Auto Iris lens plug
Honeywell’s High Resolution True Day/Night Network Box Cameras provide high picture
quality remote video surveillance over a network connection. See Table 1-1 for a list of
camera models.
Table 1-1 Network Cameras Model Numbers
Model Number Description
HCD5HIH True Day/Night 1080p Network Camera, NTSC
HCD5HIHX True Day/Night 1080p Network Camera, PAL
HCD5MIH True Day/Night 720p Network Camera, NTSC
HCD5MIHX True Day/Night 720p Network Camera, PAL
HCD5WIH True Day/Night Wide Dynamic 720p Network Camera, NTSC
HCD5WIHX True Day/Night Wide Dynamic 720p Network Camera, PAL
Figure 1-1 Camera Overview
Document 800-07067V4 Rev A 15
11/2011
Page 16
Introduction
Features
The Honeywell Megapixel IP Box Camera has the following features:
Camera Resolution Progressive Scan Sensor
HCD5HIH/X
HCD5MIH/X
HCD5WIH/X
• Mechanical Infrared (IR) cut filter ensures excellent low light performance
•Camera Tamper Detection
• Video Motion Detection
• H.264 and MJPEG compression
• Dual digital video streams simultaneously, independently configurable
• Remote firmware updates
• Support of both Dynamic and Static IP address assignment
• Multiple levels of password-protected remote access prevents unauthorized users
from altering system settings
• Advanced IP Utility software
• Web server for remote setup of camera video and network parameters
• 24V AC or PoE IEEE 802.3 af choice of power inputs
• Input and output alarm contacts support
• Bi-directional audio support
• Local video out – aim and focus
•PSIA compliant
1080p (1920 x 1080) 1/2.7" color CMOS
720p (1280 x 720) 1/4" color CMOS
720p (1280 x 720) 1/3" color CMOS
16
Page 17
2
Installation and Setup
This chapter describes how to:
•Mount the camera(s)
• Adjust the camera(s) for the clearest image
• Set up cameras in a network system
Before you Begin
Before you install your IP box camera:
• Please read this guide carefully. Keep this guide for future reference.
• Before installing the camera, Honeywell recommends that you download the latest
software updates. Go to www.honeywellvideo.com/support/
download-center/index.html and follow the instructions on the page to logon, find
your camera, and then download the latest software updates.
Note You will need a Username and Password to log in to the Download Center. To
recieve a Username and Password, contact the customer service center for
your region. Contact information is found on the Download Center page.
Unpack Everything
Check that the items received match those listed on the order form and packing slip. The
packing box should include, in addition to this User Guide:
•One network camera
• 3-pin terminal block for Power input
• 4-pin terminal block for Alarm input/output
• One product warranty
• One DVD containing the product software and the User Guide
Document 800-07067V4 Rev A 17
11/2011
Page 18
Installation and Setup
If any parts are missing or damaged, contact the dealer you purchased the camera from or
call Honeywell Customer Service (see Warranty and Service on page 13).
Overview of the Installation Procedure
This network camera is intended for indoor use only. If you choose to mount the camera
outdoors, you must employ a suitable weatherproof enclosure (such as Honeywell’s
HHC12 camera housing). See www.honeywellvideo.com for information on Honeywell
weatherproof enclosures and mounting brackets.
Note Please familiarize yourself with the installation procedure and complete each
step in the sequence given.
The initial installation of a network camera consists of the following steps:
Installation
Selecting the Lens
Step See …
1 Select the lens. page 18
2 Adjust the back focus. page 19
3 Mount the camera. page 19
4 Connect the camera. page 20
5 Program the camera. page 51
18
The network camera supports the use of a manual iris lens or DC (Direct Drive) auto iris
lens. When using a DC auto iris lens, it should be connected to the camera through the
4-pin square socket located at the side of the camera (see Figure 2-1).
If you are dissatisfied with the sharpness of the image, then you should ensure that you are
using a megapixel lens. For a list of recommended lenses, go to
www.honeywellvideo.com/products/cameras/.
Page 19
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Setscrews
Reset button restores
factory default settings
Lens connector for
DC auto Iris lens
Focus
ring
Adjusting the Back Focus
The back focus adjustment is accessible at the front end of the camera housing to adjust
the back focal length or picture focus.
The range of adjustment allows the CS-mount lenses to be used without the need for a
spacer ring.
Figure 2-1 Back Focus Adjustment
1. Loosen the setscrews with a Phillips screwdriver.
2. Adjust the focus ring at the front end of the camera housing to focus the picture.
3. Re-tighten the setscrews.
Mounting the Camera
Mounting points are provided on the top and bottom of the camera and are used to mount
the camera on a bracket or tripod for indoor applications. They are designed to accept
standard sized mounting bolts (1/4 x 20). The mounting bracket must be capable of
supporting the weight of the camera and its lens.
Caution Some installation codes state that the mounting bracket must be
For outdoor applications, mount the camera inside a weatherproof enclosure. See
www.honeywellvideo.com for information on Honeywell weatherproof enclosures.
capable of supporting up to four times the combined weight of the
camera and lens.
Document 800-07067V4 Rev A 19
11/2011
Page 20
Installation and Setup
Use standard size
mounting bolts (1/4 x 20)
to mount the camera on
a bracket or tripod.
Analog video connection
for a spot monitor
24V AC power
Audio line level input and
output connections (600
Ohm impedance).
RJ45 Ethernet network
connection (using
10Base T or 100Base
TX cable). Also for
Power over Ethernet
(PoE 802.3 af).
Alarm input (maximum rated
voltage level 24V DC) and output.
Contacts rated 12V DC @ 0.5 A.
Wiring
Figure 2-2 Camera Mount
Caution Installation must be performed by a qualified service technician and
Connecting Video
Figure 2-3 Camera Connections
must be in accordance with all national and local mechanical and
electrical codes.
20
Spot Monitor
The analog video connection is available as a test output and should be used during
installation to aim and focus the camera as needed.
Connect the VIDEO connector on the rear of the camera to the video input connector on
your spot monitor.
Page 21
Network RJ-45 Ethernet Connection
The main video connection for your network camera will be made through your Ethernet
network connection. Connect the Ethernet connector on the rear of the camera to your
network using an Ethernet (10Base-T, 100Base-TX) cable.
Connecting Power
Caution When connecting a power supply, use a 24V AC power plug or a PoE
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Note You can connect your camera to a network or connect it directly to a PC or
laptop using a crossover cable.
IEEE 802.3 (Power over Ethernet) compatible hub. To avoid damage
to the camera, never connect more than one type of power supply at
the same time.
WARNING! The use of a CSA Certified/UL Listed Class 2 power supply is
required to ensure compliance with electrical safety
standards.
Note Check the power source from the external power supply before applying
power to the camera.
1. Connect the camera to a power supply appropriate for your installation:
• 24V AC power supply (proceed to step 2)
• Power over Ethernet (PoE IEEE 802.3 af) 48V DC power supply
Note Connect power either from a 24V AC source or CAT5 Ethernet connector
(PoE). It is not recommended to connect both power sources at the same
time.
Document 800-07067V4 Rev A 21
11/2011
Page 22
Installation and Setup
Note If you are using PoE (802.3 af), power will automatically be supplied to the
camera through the network cable.
2. Plug in the power supply. Use a screwdriver to first loosen the ~AC24V terminal
screws on the terminal block.
Note To ease installation, the terminal block can be removed. The power
connections of the removable terminal block are not polarity-sensitive.
Connect either power lead to either connector terminal.
3. Secure the power leads by tightening the terminal screws until snug.
4. Plug the power supply into an appropriate power source.
Note For secure installations, surface-mounted cables should be protected by
plastic or metal cable covers.
Note If your installation involves a 24V AC power source, then please wait
approximately 60 seconds after connecting to a power source for video to
appear on the local video out.
Caution Installation must be performed by a qualified service technician. The
proper wire gauge for the distance and number of cameras must be
determined to maintain 24V AC at each camera.
Caution When powering the camera from 24V AC, a UPS source should be
considered to ensure satisfactory performance.
22
Note Connect power either from a 24V AC source or CAT5 Ethernet connector
(PoE). It is not recommended to connect both power sources at the same
time.
Page 23
Connecting Alarms
IN
OUT
IN
OUT
ALARM
Normally closed
Normally opened
WARNING! Do not exceed the maximum rating of 12V DC, 0.5 A on alarm
The network camera has one alarm input and one alarm output available to connect to
peripheral devices (Figure 2-4).
Figure 2-4 Alarm Connections
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
output connections.
Connect mechanical or electrical switches to the alarm input connection to allow
event-triggered recording. When alarm inputs are configured, the camera triggers an alarm
only when the normal state (open or closed) changes (see Figure 2-5). See Alarm Settings
on page 59 to configure the alarm inputs.
The network camera has a LAMP setting which allows control of the moving IR cut filter
when there is a change in state from Normally Open to Normally Closed (see Alarm Settings
on page 59 for more information). In this way, the moving IR cut filter and the day/night
operation of the camera can be synchronized with external lighting changes using a
common controller such as a photocell or timer.
Figure 2-5 Normal Alarm States
Connect external devices such as sirens or flashing lights to the alarm output connector to
signal users of the camera that an alarm is activated. See Figure 2-6 for alarm connection.
Document 800-07067V4 Rev A 23
11/2011
Page 24
Installation and Setup
+
–
IN
OUT
IN
OUT
ALARM
In
Out
+
–
Figure 2-6 Alarm Output Connection
The alarm output can be configured to provide normally open or normally closed contacts
(see Alarm Settings on page 59 to configure the alarm output). Contacts will be rated for
12V DC @ 0.5 A.
Connecting Audio
The network camera supports bi-directional audio. There are two supported voice band
channels that function in full duplex mode. The camera can transmit audio from the camera
to the client (PC) using any audio source that provides an industry standard line level input
(3.5 mm jack). The camera can also receive audio from the client (PC) and provide an
industry standard line level output (3.5 mm jack) suitable to connect to audio devices. Audio
input and output have 600 Ohm impedance. See Audio Settings on page 59 to configure
audio options.
Restoring Factory Defaults
Your network camera has a Factory Reset switch on the side of the camera (see Figure 2-1).
Use this switch to restore your camera options and passwords to their default settings. Use
a pin or straightened paperclip to press and hold the Reset switch for five seconds.
24
Page 25
3
Installing the Honeywell IP Utility and Web
Client Software
This chapter describes how to:
• Install and log onto the IP Utility
• Connect to a device and configure network settings using the IP Utility
• Launch the web client software
• Uninstall the IP Utility, Bonjour, or ActiveX software
• Perform firmware upgrades
About the Honeywell IP Utility and Web Client
About the Honeywell IP Utility
The Honeywell IP Utility is a software application that is installed from a DVD or
downloaded from the Honeywell Systems Group website (www.honeywellvideo.com). It
is installed on a local workstation and primarily used by Administrators to configure the
®
EQUIP
The IP Utility enables users to:
• Discover device(s) on a network
• Configure the IP network settings, name device(s), upgrade firmware, change
• Open individual web client applications for each discovered device.
Note Before installing and using the Honeywell IP Utility, confirm that your camera
Document 800-07067V4 Rev A 25
11/2011
Series of products residing on an IP network.
passwords.
is connected to the network through an Ethernet cable (see Network RJ-45
Ethernet Connection on page 21).
Page 26
Installing the Honeywell IP Utility and Web Client Software
About the Web Client
The web client is the web-based application that enables users to:
• View live-streaming video.
• View the device network settings and firmware details.
• Configure camera settings
• Configure video analytics settings.
• Configure compression settings.
• Configure alarm and audio settings.
User Profiles: Honeywell IP Utility and Web Client
Both the Honeywell IP Utility and the web client have two user types: Administrator and
Guest as described in Table 3-1.
After the IP Utility software is installed, you can change the Administrator or Guest
passwords.
Table 3-1 User Profiles for Honeywell IP Utility and the Web Client
Interface Administrator/Admin Guest
Honeywell IP
Utility
Web Client • View video and network settings.
• View the list of available network devices
and connect to the devices.
• Configure the IP network settings.
• Upgrade firmware.
• Change the password to access the IP
Utility application.
• Change the access passwords to the
web client application.
• Configure compression settings.
• Configure camera setup.
• Configure video analytics.
• Configure audio and alarms.
• View the list of devices available on the
• View system settings including device
• Guest users are limited to the Live View
network.
name, IP address, and MAC address.
tab where they can view video
26
Page 27
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Step 1: Confirm Your System Requirements
Note Windows administrator privileges are required to install the Honeywell IP
Utility and associated software.
Note Contact the network administrator if there are any questions regarding the
local area network (LAN) or any other network related issues.
Install the Honeywell IP Utility on a work station with the minimum requirements (outlined
in Table 3-2). After the IP Utility is installed, the same computer workstation can be used to
access the web client.
Table 3-2 PC Minimum System Requirements
Component Requirement
®
Operating System Windows XP
or WINServer 2003
Processor Intel® Pentium® IV, 3.1 GHz or faster
RAM 1 GB RAM (32-bit) or 2 GB RAM (64-bit)
Internet Explorer 6, 7, or 8
Table 3-3 Items Installed On Your System
Item Function
Honeywell IP Utility software To enable use of the web client to configure
Bonjour software To discover cameras on the network.
Honeywell PSIA IP Adapter
software
Honeywell ActiveX software To enable live streaming of video on the web
®
EQUIP
Series User Guides To provide detailed information about how to
, Windows 7 (32/64), Windows 2K8 (32/64),
cameras and view live video.
To enable web client and systems operation with
PSIA devices.
client.
install and configure your EQUIP Series products.
Document 800-07067V4 Rev A 27
11/2011
Page 28
Installing the Honeywell IP Utility and Web Client Software
Step 2: Install the Honeywell IP Utility Software
1. Close all other applications that might be open on your computer.
Note We recommend that you disable any Norton AntiVirus software that might be
running on the workstation.
2. Disable User Account Control (UAC) Settings (for Windows 7 and Windows 2K8 only).
If you do not disable UAC, you will be unable to install the ActiveX software.
a. Go to Getting Started
b. Change the UAC setting to Never Notify.
c. Click OK to save the new setting.
3. Open the Honeywell IP Utility InstallShield Wizard.
Method 1: DVD
Insert the DVD into the DVD-ROM drive.
Change UAC Setting.
Note If InstallShield does not open automatically, navigate to [DVD
drive]\Honeywell IP Utility\Honeywell IP Utility Setup.exe. Double-click on
the file to launch the program.
Method 2: Website
a. Navigate to www.honeywellvideo.com.
b. Click Customer Resources
page.
Note You will need a Username and Password to log in to the Download Center. To
recieve a Username and Password, contact the customer service center for
your region. Contact information is found on the Download Center page.
c. Log into the Download Center.
d. Click Cameras under Video Systems Products.
e. Under Honeywell IP Utility, download, extract and click to download the latest
Honeywell IP Utility Set-up software.
4. When the Honeywell IP Utility InstallShield Wizard opens, follow the instructions.
After the installation is complete, a Honeywell IP Utility icon displays on the
desktop.
Download Center to reach the Download Center
28
Page 29
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Downloading the EQUIP Series Installation Guides
1. To access the installation documents that were installed with the IP Utility, click Start
Programs Honeywell Video Systems Manuals EQUIP Series
HCD5 Series.
2. Select the applicable PDF to download to your computer.
Figure 3-1 Accessing Your Installation Documents
IStep 3: Log Onto the IP Utility and Discover Network Devices
1. Double-click the Honeywell IP Utility icon on your desktop.
-ORClick Start
IP Utility.
The Honeywell IP Utility Log On window opens.
Figure 3-2 Honeywell IP Utility Log On Window
2. Select Administrator or Guest from the User Name drop-down list.
Programs Honeywell Video Systems IP Utility Honeywell
Document 800-07067V4 Rev A 29
11/2011
Page 30
Installing the Honeywell IP Utility and Web Client Software
3. Enter the case-sensitive password in the Password field.
• The default Administrator password is 1234.
• The default Guest password is guest.
Note During the installation set up, you must log on as an Administrator to access
all the features.
4. Click the arrow button .
The Honeywell IP Utility program searches for devices on the network and opens to
the Honeywell IP Utility user interface.
5. Automatically discover or manually refresh the list of devices on the network.
Use the manual refresh if a new device was added after you logged onto the system.
• You do not need to do anything to discover devices. When you log on to the IP
Utility, the devices on the network — including the devices on other subnets —
are automatically discovered and listed in the Discovery pane. After the initial
discovery, the network automatically continues to discover devices that are newly
added to the network.
• To manually refresh the device list, click the Refresh ( ) button, located near
the top of the Discovery pane.
6. Enable or disable the HTTP Server checkbox for additional security. Only an
Administrator can disable (uncheck the box), resulting in the user being unable to
access the web client, although video recording is unaffected. Figure 3-3 shows the
Honeywell IP Utility interface.
Note All examples in this User Guide show the GUI for the HCD5MIH model
camera, unless otherwise specified.
30
Page 31
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
The About menu displays the
software version installed.
The Status bar displays how many
devices are on the network, which
one you are connected to, and
which user is logged on.
The Discovery pane lists
the IP devices found on the
network and groups by
device type.
On the User tab, Administrators
can change the web client user
passwords.
IP Network Setting assigns
network settings automatically
or manually.
Connect button
Disconnect button
Limited/No connectivity
button
Refresh button
Upgrade Firmware
downloaded from the
Honeywell website.
Use the Product Filter drop-down
menu to select a specific device,
such as all
HCD5 series cameras.
Click Apply to save
manually configured
network settings.
Use Launch Browser
to open the HCD5
series IP web client for
each device.
Use Batch Firmware Upgrade
to select a group of devices and
upgrade the firmware for all.
Enable or disable HTTP
Server.
Figure 3-3 Honeywell IP Utility User Interface
Step 4: Connect to a Device and Configure Network Settings
Document 800-07067V4 Rev A 31
11/2011
When you log on to the IP Utility, the devices on the network — including the devices on
other subnets — are automatically discovered and are listed in the Discovery pane. After
the initial discovery, auto-refresh continues to discover devices that are newly added to the
network.
Page 32
Installing the Honeywell IP Utility and Web Client Software
You can also manually refresh the device discovery by clicking the Discovery icon ( ),
located near the top of the Discovery pane.
Connecting to or Disconnecting from Devices
Before configuring the IP network settings, you must connect to an IP device.
Connecting to a Device
You can connect to individual web client applications for each discovered device.
•In the Discovery pane, double-click the device to which you want to connect.
-OR-
• Select the device and click the Connect button.
The network settings for the connected device are displayed in the System pane.
Disconnecting from a Device
In the Discovery pane, select the device and click Disconnect .
Note If you disconnect the device without saving configuration details, a warning
dialog box displays. Click Yes to save and disconnect, or click Cancel to
discard the changes and disconnect the device.
Configuring the IP Network Settings Automatically or Manually
Note When you see the Limited/No connectivity button, you cannot fully
connect to the device because the discovered device is on a different subnet
from your PC. Check your network settings for both the device and your PC to
resolve this issue. Consult your network administrator for additional support.
32
The IP network setting details, such as device name, IP address, and subnet mask can be
configured for each connected device either automatically or manually.
Note It is important to click Apply to save any configuration change.
Page 33
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Click to clear this checkbox and
manually set the network details
Table 3-4 IP Network Device Setting Options
Option Description
Device Name By default, the device name is the device type plus the MAC Address. Honeywell
recommends, for security, that you change the device name.
IP Address The IP address of the device on the network.The camera obtains an IP address
by static or dynamic (automatic) means. There are two ways: Dynamic
(DHCP/APIPA), which is automatically assigned by the network administrator, or
Static (static), which is assigned by the user.
Subnet Mask The subnet mask, or netmask, value of the device on the network. IP networks
can be divided into several smaller networks by subnetting. When a network is
subnetted, you must specify a subnet mask, which tells network devices which
smaller network they belong to.
Note If the subnet mask is not properly configured, the camera might not be
able to communicate with other devices on the network.
Default Gateway The default gateway address that connects the device to the network. Enter the
IP address of the host to use as a gateway between networks. The gateway
allows communication between devices that are on different networks. Without a
correct gateway setting, the camera cannot receive or transmit data from or to
devices that are not in the same network address range.
MAC Address The MAC address is a factory-assigned address that is unique for each device.
Figure 3-4 Setting the IP Network Settings Automatically or Manually
Note All examples in this User Guide show the GUI for the HCD5MIH model
camera, unless otherwise specified.
Document 800-07067V4 Rev A 33
11/2011
Page 34
Installing the Honeywell IP Utility and Web Client Software
Updating IP Network Settings Automatically
1. In the Discovery pane, select the device and click Connect .
2. From the System tab click the Obtain an IP Address automatically check box.
3. Enter a Device Name, for example, FrontLobbyCam01.
4. Click Apply.
The network automatically assigns the IP Address based on the DHCP network server
details. If no DHCP server is present on the network, the hardware defaults to an
APIPA address (169.254.x.x).
Updating IP Network Settings Manually
Caution When manually updating the network settings, it is important to enter
the correct IP network settings before applying them. Incorrect values
might cause a failure when connecting to the device. See Table 3-4
for definitions of each setting.
1. In the Discovery pane, select the device, and click Connect .
2. To assign a static IP address to the device, from the System tab click to clear the
Obtain an IP Address automatically check box.
3. Enter a Device Name, for example, FrontLobby01.
Note The MAC address is a factory assigned address that is unique for each
device.
4. Enter an IP Address of the device on the network.
Note The address must be in the same address range. For example, if the PC is
192.168.1.xx, then the device should be set to a similar address, for example
192.168.1.xy.
5. Enter the device Subnet Mask value. A value is required.
6. Enter a default Gateway Address that connects the device to the static network. A
value is required.
7. Click Apply.
The network settings are updated and a message displays in the status bar to confirm
the update.
34
Page 35
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Interfacing with the EQUIP PSIA Device Via a Network Video Recorder
This camera supports the PSIA specification for interoperability between network video
products. There is no support for legacy EQUIP and EQUIP2 protocols.
For further information, refer to the documentation supplied with your NVR or contact your
NVR network administrator.
Step 5: Launch the Web Client to View Live Video
Note After the IP Utility software is installed for the first time, you can change the
Administrator or Guest passwords and upgrade firmware.
Note It is important to click Apply in order to save any configuration change.
1. Log onto the web client. There are two ways to launch the web client and log on— via
the Honeywell IP Utility Program or directly from Internet Explorer.
Honeywell IP Utility
a. Log onto the Honeywell IP Utility program.
b. From the Discovery pane, click to select the device to launch its browser.
c. To enable or disable the HTTP server, select or clear the Enable HTTP Server
check box. By default, the HTTP server is enabled.
d. From the System tab, click Launch Browser.
The web client application for the selected device opens in Internet Explorer.
Internet Explorer
From Internet Explorer (v6.0+), enter the URL (IP address of the device) in the
Address bar to open the logon window.
2. Select a User Name and enter a Password.
a. From the User Name drop-down list, select admin or guest.
b. In the Password field, enter the case-sensitive password.
• The default Administrator password is 1234.
• The default Guest password is guest.
c. Click .
Document 800-07067V4 Rev A 35
11/2011
Page 36
Installing the Honeywell IP Utility and Web Client Software
3. A signed version of ActiveX® control is installed when you use the web client to
discover connected devices for the first time. If you have a previous version of IP
ActiveX is installed, you are prompted to upgrade to Honeywell secure ActiveX
control.
Figure 3-5 ActiveX Prompt
Click Yes.
4. Follow the InstallShield Wizard prompts to install the secure Honeywell IP ActiveX on
your PC.
5. The InstallShield Wizard Completed message indicates a successful ActiveX
upgrade. Click Finish.
The web client interface opens and live streaming video displays on the monitor.
Figure 3-6 Web Client Interface After Logging On
36
Page 37
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Uninstalling IP Utility, Bonjour or the ActiveX Plug-in Software
You can uninstall the IP Utility, Bonjour, or IP ActiveX software using:
•The Start menu to uninstall IP Utility and Bonjour
OR
•The Control Panel to uninstall IP Utility, Bonjour and IP ActiveX.
Uninstalling IP Utility Using the Start Menu
1. Click Start All Programs Honeywell Video Systems IP Utility Uninstall
Honeywell IP Utility.
2. Click Yes.
The Honeywell IP Utility is uninstalled.
3. During the uninstallation process, you are prompted to also uninstall the Bonjour
program. Click Yes to remove Bonjour or No to only uninstall the Honeywell IP Utility.
4. Click Finish.
Uninstalling IP Utility or IP ActiveX Using the Control Panel
1. Click Start Settings Control Panel.
2. Open Add or Remove Programs and select Honeywell IP Utility or Honeywell IP
ActiveX from the Currently installed programs list.
3. Click Change/Remove.
The IP Utility Installation Wizard screen opens.
4. Click Next
The Honeywell IP Utility is uninstalled.
5. During the uninstallation process, you are prompted to also uninstall the Bonjour
program. Click Yes to remove Bonjour or No to only uninstall the Honeywell IP Utility.
6. Click Finish.
Remove.
Document 800-07067V4 Rev A 37
11/2011
Page 38
Installing the Honeywell IP Utility and Web Client Software
38
Page 39
4
IP Camera Web Client
Before you launch the Honeywell IP web client, ensure that you complete the following
sections before configuring your HCD5 series camera:
• Chapter 2, Installation and Setup
• Chapter 3, Installing the Honeywell IP Utility and Web Client Software
This chapter covers:
• Navigating the web client interface
• Understanding the web client features and functions
• Configuring compression settings
• Configuring camera settings
• Setting tamper detection
• Configuring audio, alarm, and motion detection settings
Overview
The network camera web client is a web-based application that enables you to view video,
listen to audio, and configure camera, sabotage detection, motion detection, alarm, and
audio settings for the network camera.
Certain features of the IP Camera web client are user-based and are available only to the
Administrator. Guest users are limited to the Live View tab.
Document 800-07067V4 Rev A 39
11/2011
Page 40
IP Camera Web Client
User Profiles
Table 4-1 describes the roles and privileges for the web client application users:
Table 4-1 User Roles and Privileges
User Role User Name Privileges
Administrator admin • View video and network settings
• Configure the alarm and audio settings
• Set up the video compression settings
• Configure auto exposure and white balance
for the camera
• Set up camera sabotage and video motion
detection settings
Guest
Operator
guest • View video
Logging On and Off the IP Web Client
There are two ways to open each IP web client.
• By clicking Launch Browser from the IP Utility interface.
• Directly from Internet Explorer by entering the URL (the IP address) in the address
bar.
Launching the Web Client from IP Utility
1. From the desktop, double-click the Honeywell IP Utility icon .
-ORClick Start
IP Utility.
The Honeywell IP Utility Log On window opens.
2. From the User Name drop-down list, select Administrator or Guest.
See Table 4-1 on page 40 for User roles and privileges.
3. In the Password field, enter the case-sensitive password.
• The default Administrator password is .
• The default Guest password is guest.
4. Click .
The Honeywell IP Utility program searches for devices on the network and opens to
the Honeywell IP Utility user interface.
Programs Honeywell Video Systems IP Utility Honeywell
Only one Administrator can be logged in at a time.
40
Page 41
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Connect to the device then click
Launch Browser
Enable HTTP
Server must be
enabled. If it isn’t,
the Launch
Browser button
might not be
available.
5. In the Discovery pane, double-click the device you want to connect to.
-ORSelect the device and click Connect .
The network settings for the connected device are displayed in the System pane.
6. Click Launch Browser (see Figure 4-1) to go to the web client logon page.
Figure 4-1 Launching the Web Client from the IP Utility
Note All examples in this User Guide show the GUI for the HCD5MIH model
camera, unless otherwise specified.
Note If the Launch Browser button is inactive, then you must enable Enable HTTP
Server. Click to enable the HTTP Server, and then click Apply. The Launch
Browser button should then be enabled.
Document 800-07067V4 Rev A 41
11/2011
Page 42
IP Camera Web Client
Logging Onto the Web Client from Internet Explorer
1. From Internet Explorer (v6.0+), enter the URL (IP address of the device) in the
Address bar to open the logon window.
The web client log on page opens.
2. Select a User Name and enter a Password.
a. From the User Name drop-down list, select admin or guest.
b. In the Password field, enter the case-sensitive password.
• The default Administrator password is 1234.
• The default Guest password is guest.
c. Click .
3. The web client interface opens and live streaming video displays on the monitor.
Logging Out of the Web Client
To log out from the web client application, click Logout at the top of the web client window.
42
Page 43
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
The URL corresponds to the IP Address as
configured in the IP Utility.
Click Logout to exit the program.
Confirm the user type logged in.
Each tab has a section for configuration
and/or navigation controls.
Click the tabs
to access the
available
configurations
and settings.
If logged on as a Guest, only the Live
View tab is available. Administrators
can access all tabs.
The image from your
HCD5 series camera
displays on every tab.
SnapShot
Navigating the Web Client User Interface
Figure 4-2 Web Client Window Layout: Administrator Log On
Document 800-07067V4 Rev A 43
11/2011
The web client application user interface consists of multiple user-friendly views organized
by function. Access to the views is user-controlled.
Table 4-2 Tabs/Views in the Web Client Application
Tab Enables you to...
Live View View video and take SnapShots.
Device Settings View the network settings and firmware details of the camera.
Restore to factory defaults and reboot a camera.
Compression
Settings
Select the compression mode.
Set the maximum bit rate and/or target bit rate that the camera will
provide across the network based on priority mode settings. This
value is the threshold that you do not want the bit rate to exceed.
View received bit rate and frame rate statistics of the current image
in real time.
Camera Setup Configure auto exposure and white balance for the camera.
Video Analytics Configure the camera sabotage detection settings and view video
display.
IO and Audio Configure the alarm and audio settings.
Page 44
IP Camera Web Client
The menu bar displays
which user is logged on
and provides a link to log
out of the application.
Screens are divided
between displaying
current video and the
configuration options
associated with the view.
Click a Tab to
display the
corresponding view.
Click to select the
video stream.
SnapShot
When an alarm is
detected, an alarm
message appears here
to notify the operator.
Logging on as a Guest limits users
to Live View tab functions only.
See Live View for more details.
When an alarm is detected,
an alarm message appears
here to notify the operator.
SnapShot
Figure 4-3 Web Client: Administrator User
Figure 4-4 Web Client: Guest User
Live View
44
Live View shows live video from the selected camera (see Figure 4-4).
Page 45
Taking a SnapShot
The SnapShot function allows you to save an image from Live View to a default folder
on your computer (C:\Program Files\Honeywell Video Systems\Support\Snapshots). Files
are saved as: DeviceName_Date_Time.bmp. You are not asked for confirmation.
SnapShot is available to Administrators and Users with administrator and guest privileges.
Device Settings
The Device Settings tab allows you to view the network settings and firmware details of the
camera. It also allows you to restore or to reboot a device.
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Configuring IP and Firmware Settings
Depending on the hardware installation, there is a tab called either Device Information or
Device Settings. In both cases, the IP and Firmware Settings panel mirrors the information
available in the Honeywell IP Utility. It provides read-only network settings, firmware
settings, and video formats without having to access the IP Utility.
The Device Settings are the same for the Primary and Secondary streams.
Figure 4-5 Device Settings
Document 800-07067V4 Rev A 45
11/2011
Page 46
IP Camera Web Client
Device Name as entered in the IP
Utility program
IP Address on the network
(DHCP/Static/APIPA)
Firmware Settings including
product name and version
Video Output - Enable or disable local video
out to a spot monitor. HCD5HIH(X) only.
Note Enabling Local Video Out will
disable to the secondary video
stream. HCD5HIH(X) only.
Subnet Mask and Default Gateway
address that connects the camera to
the network
MAC Address is a factory assigned
address unique for each device
Video Format - NTSC or PAL
Select a location for saving Snapshots
Figure 4-6 IP and Firmware Settings: Device Information Tab
Resetting the Device
46
You can choose from Restart, Restore, and Reset to Defaults. See Figure 4-6. Each of
these functions take approximately 2 minutes to complete, and during that time, the camera
will lose connection to the web client. You will be asked if you wish to proceed before the
action occurs.
Restart Restarts the camera while maintaining the existing configurations.
Restore Resets the camera to the factory defaults, except the network settings.
Reset to
Defaults
Resets the camera to the factory defaults, including the network
settings.
Page 47
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Compression Settings
The video signal sent from the camera to the web client has a number of settings that can
be edited which affect how the video displays in the web client. The Compression Settings
view enables you to configure these settings:
•Stream Type
• Enable/Disable the Secondary Stream
•Resolution
•Frame Rate
•Priority (Quality, Bit Rate, or Frame Rate)
• Compression Ratio (if Quality is chosen as the priority)
• Target Bit Rate (if Bit Rate or Frame Rate is chosen as the priority)
• Maximum Bit Rate that the camera will provide across the network (if Quality is
chosen as the priority)
• GOP (number of frames) / Key Frames
Figure 4-7 Compressions Settings Tab: Primary Stream
Your camera supports simultaneous video streams. The Primary stream delivers H.264
compressed video in real time 30 fps at 1280 x 720 resolution. The Secondary stream
delivers MJPEG compressed video in real time 30 fps at 640 x 360 resolution.
Document 800-07067V4 Rev A 47
11/2011
Page 48
IP Camera Web Client
Set the Resolution
Set the Frame Rate
Set the
Priority
to Quality, or Bit or Frame Rate
Set the Compression Ratio
Set the Target Bit Rate
Set the Maximum Bit Rate (kbps)
Set the GOP (Group of Pictures)
Default settings shown for NTSC models
Set the Frame Rate
Set the
Priority
to Quality, or Bit or Frame Rate
Set the Compression Ratio
Set the Target Bit Rate
Set the Maximum Bit Rate (kbps)
Enable/Disable the secondary stream
Set the Resolution
Default settings shown for NTSC models
Primary Stream Video Codec Settings
Figure 4-8 Primary Stream Video Codec Settings
Secondary Stream Video Codec Settings
Click on the Secondary Stream tab. A warning message appears: The secondary
stream is disabled. To enable, select compression settings tab and
configure secondary stream.(HCD5HIH only)
You will have access to the Secondary Stream Video Codec Settings.
Figure 4-9 Secondary Stream Video Codec Settings
Note Enabling the secondary (MJPEG) stream disables the local video out (aim
and focus). (HCD5HIH only)
48
Page 49
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
.
Select this Priority
field setting
Field Setting Description
Quality
(see Figure 4-10)
Maximum Bit Rate
The Target Bit Rate field
is grayed out.
The camera maintains the picture quality until the
bit rate delivered exceeds the Maximum Bit Rate
(MBR), at which point the camera drops frames to
ensure that the MBR is not exceeded.
Bit Rate
(see Figure 4-10)
Target Bit Rate
Maximum Bit Rate and
Compression Ratio fields
are grayed out.
The camera adjusts the picture quality to ensure
that the bit rate delivered does not exceed the
Target Bit Rate (TBR), at which point the camera
drops frames to ensure that the TBR is not
exceeded.
Frame Rate
(see Figure 4-10)
(Not available for
for Secondary
stream)
Target Bit Rate
Maximum Bit Rate and
Compression Ratio fields
are grayed out.
The camera maintains the selected frame rate
while adjusting image quality to meet the TBR. This
mode allows the actual bit rate to fluctuate beyond
the user-defined TBR while maintaining the
selected frame rate.
Configuring the Compression Settings
1. On the Compression Settings tab, in the Statistics area, select the Received check
box to receive in real time the bit rate and frame rates for the current image.
Deselecting the check box disables the refresh rate.
Note The Received check box is disabled by default. When you log out, this check
box reverts to the disabled state.
2. Use Table 4-3 to set up the streaming resolution and Table 4-4 for the other
compression settings.
Table 4-3 Video Streaming Resolutions
Primary Stream Resolutions Secondary Stream Resolutions
1920 x 1080 (HCD5HIH only)
1280 x 720
800 x 450
640 x 360
320 x 180
Table 4-4 Compression Settings
Setting Options Description
Frame Rate 1–30 (NTSC)
1–25 (PAL)
Priority Quality, Bit Rate,
Frame Rate
The frame rate that is displayed per second. For NTSC, select from 1 fps (lowest)
to 30 fps (highest). For PAL, select from 1 fps (lowest) to 25 fps (highest).
Allows you to set the maximum bit rate and/or target rate value, based on priority
mode settings. This value is the threshold that you do not want the bit rate to
exceed. The Secondary Stream is configurable for Quality or Bit Rate only. [?]
640 x 360
320 x 180
Document 800-07067V4 Rev A 49
11/2011
Page 50
IP Camera Web Client
Statistics are received for the current image in real time when Received is enabled.
Set the Resolution for NTSC or PAL video signals.
Table 4-4 Compression Settings(cont’d)
Setting Options Description
Compression
Ratio
Target Bit
Rate (kbps)
GOP (No. of
Frames)
Minimum, Low,
Medium, High,
Maximum
250 – 6000 kbps Enter the Target Bit Rate in kbps (kilobits per second) which represents the
1– 50 Select the GOP (Group of pictures) number from 1 to 50. (Not available on the
Figure 4-10 Video Codec Settings
When Quality is selected as the Priority, select the Compression Ratio.
Minimum is the highest visual quality; Maximum is the lowest visual quality.
amount of data processed per second.
Secondary Stream.)
3. Click Apply. Adjustments in your compression settings are captured in the statistics.
As you make adjustments, the Statistics field acts as a visual reminder of how your
settings affect the bit rate, frame rate, and bandwidth usage.
4. When you are satisfied with your settings — that is, that the image quality and
bandwidth usage meets your requirements — click Apply to save your settings.
Settings are not saved unless you click Apply.
Statistics: Received Bit Rate and Frame Rate
To view in real time the received bit rate and frame rate statistics of the current image:
1. Click the Compression Settings tab.
2. In the Statistics area, select the Received check box.
50
Page 51
Camera Setup
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Deselecting the check box disables the refresh rate.
Note The Received check box is disabled by default. When you log out, this check
box reverts to the disabled state.
The Camera Setup view provides access to the settings used to configure the camera
configurations for both Primary and Secondary streams. The following section explains
Auto Exposure and White Balance setup.
Note You must click Apply after you make changes to any settings to save those
changes. Settings are not saved unless you click Apply.
Figure 4-11 Camera Setup
Auto Exposure
The Auto Exposure settings allow the user to access and configure exposure-related
settings as described in Table 4-5.
Document 800-07067V4 Rev A 51
11/2011
Page 52
IP Camera Web Client
Note You must click Apply after you make changes to any settings to save those
changes. Settings are not saved unless you click Apply.
Table 4-5 Auto Exposure Settings
Setting Options Description
ELC (Electronic Light
Compensation)
ALC (Automatic Light
Compensation)
(HCD5MIH and
HCD5HIH only)
AGC (Automatic Gain
Control)
DNR (Digital Noise
Reduction)
Flickerless
(HCD5MIH and
HCD5HIH only)
DSS
(Digital Slow Shutter)
Day/Night Auto, Day, Night Controls True Day/Night (TDN) operation. When Auto is selected, the
Level 1–25 Electronic shutter control. Select ELC when using a manual iris lens.
Adjust the ELC level to the appropriate value so that the image is well
exposed (neither too bright nor too dark).
DC Iris Level: 1 – 25 Select ALC when using a DC (auto iris) lens. Adjust the ALC level to the
appropriate value so that the image is well exposed (neither too bright
nor too dark).
Off, 20 dB–40 dB Adjust the maximum value of AGC gain. AGC can be Off, or set to
20 dB, 30 dB, or 40 dB.
Note As AGC levels are reduced, the threshold ranges for DayToNight
and NightToDay are decreased.
Off, On Improves picture performance in low light by reducing video noise.
DNR is deactivated if AGC is turned Off.
Off, On Eliminates the “flicker” that can appear in an image under certain
lighting conditions (for example, fluorescent lighting). This setting is not
available if you have selected ELC.
Off, Low, High Automatically provides a clear image under low-light conditions. DSS
improves the picture quality (brightness) in low-light scenes. DSS might
introduce motion blur; the higher the setting, the more likely motion blur
will occur.
IR-cut filter will be removed automatically in low-light scenes. When Day
is selected, the IR-cut filter is on at all times. When Night is selected, the
IR-cut filter is off (removed) at all times.
Night Mode B/W or Color Sets the color mode as B/W (monochrome) or Color in Night Mode.
Day/Night must be set to Night.
Detect Time 5–60 seconds Sets the time (5–60 seconds) before the camera switches to Day or
Night mode after detecting a low-light condition or a normal light
condition, respectively.
Day/Night must be set to Auto.
WDR (Wide Dynamic
Range) (HCD5WIH
only)
LDC (Lens Distortion
Correction)
(HCD5WIH only)
52
Off, Low, Medium,
High
Off, On When On, LDC reduces picture distortion. The performance of Frame
Wide dynamic range provides clear, balanced images in high-contrast
lighting conditions. Set the WDR to Off, Low, Medium, or High.
Rate mode might be impacted by LDC.
Page 53
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Table 4-5 Auto Exposure Settings (cont’d)
Setting Options Description
DayToNight 1 –7 Determines the low light detection level (1–7) when the camera
switches to Night mode. The lower the value, the darker the lighting
conditions before the camera switches.
Day/Night must be set to Auto.
Note The DayToNight threshold level must be set at least 2 less than
the NightToDay threshold setting.
Note The DayToNight threshold range is decreased if the AGC level is
reduced.
NightToDay 3 –9 Determines the low light detection level (3–9) when the camera
switches to Day mode. The higher the value, the brighter the lighting
conditions before the camera switches.
Day/Night must be set to Auto.
Note The NightToDay threshold range is decreased if the AGC level is
reduced.
White Balance
White Balance ensures that color integrity is maintained in the camera image by
compensating for the temperature color “casts” that different light sources can cause. Use
Table 4-6 to set up White Balance options.
Note You must click Apply after you make changes to any settings to save those
changes. Settings are not saved unless you click Apply.
Table 4-6 White Balance Settings
Option Description
Auto (Auto White
Balance Control Mode)
Manual Manual white balance mode. Set the Red and Blue gains
WBC Push (Auto White
Balance Control Mode)
An automatic white balance mode that can be used in
scenes which have constant lighting. The user can optimize
WB for the given scene by pressing and holding an
adjustment button.
from 0–255.
Automatically adjust the white balance to your specific
environment. When selected, the white balance is locked.
Note This setting is recommended for situations in which
the light conditions are constant, so that the
specified color temperature does not change.
Document 800-07067V4 Rev A 53
11/2011
Page 54
IP Camera Web Client
Each Tamper Detection
Setting provides 3
threshold levels: High
(80%), Medium (50%)
and Low (30%).
Video Analytics
Your camera can be configured to detect camera sabotage and motion within a scene via
the Video Analytics view (see Figure 4-12). The Video Analytics tab enables a user to set the
tamper detection threshold settings for blur, blinding and scene changes.
Figure 4-12 Video Analytics Tab
Each setting has three threshold levels: high (80%), medium (50%) and low (30%). When
these thresholds are exceeded, camera sabotage or motion is detected, and alarm
messages appear above the video display and alarm signals are sent to DVRs/NVRs (see
Figure 4-14).
54
Page 55
Sabotage Detection
Set the Blur Threshold. Blur
can be affected by elements
such as water, for example
Set the Blinding Threshold.
Blinding applies to obstacles in
front of the camera lens
Set the Scene Change
Threshold
Figure 4-13 Tamper Detection Settings on the Video Analytics Tab
There are three types of sabotage detection in the Tamper Detection Setting tab on the
Video Analytics tab: blinding the camera, blurring the video display, and tampering with the
camera field of view. The user should note that when the following conditions are
applicable, the tamper detection features should be manually disabled to avoid raising false
alarms:
• During the configuration of the video display
• While text is overlaid on the video
• If the video display becomes too dark
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Figure 4-14 Video Analytics Alarm Message
Configuring Video Blur Detection
The video appears blurred when the camera is exposed to elements such as water. When
this occurs, video blurring in the field of view is detected and an alarm message appears
(see Figure 4-14) above the video display. To detect video blurring:
1. Click the Video Analytics tab.
2. In the Blur Threshold list, select one of the following options:
Table 4-7 Blur Threshold Values
Value To detect …
High (80%) Maximum video blurring. The alarm message appears when
the video display is blurred by 80% or more.
Medium (50%) Medium video blurring. The alarm message appears when
the video display is blurred by 50% or more.
Low (30%) Minimum video blurring. The alarm message appears when
the video display is blurred by 30% or more.
3. Click Apply.
Document 800-07067V4 Rev A 55
11/2011
Page 56
IP Camera Web Client
Note To turn off video blur detection, select Disable in the Blur Threshold list.
Disable is the default value.
Note You must click Apply after you make changes to any settings to save those
changes. Settings are not saved unless you click Apply.
Configuring Camera Blinding Detection
An obstacle in front of the camera lens can blind the camera. When this occurs, camera
blinding is detected and an alarm message appears above the video display (see
Figure 4-14). To detect camera blinding:
1. Click the Video Analytics tab.
2. In the Blinding Threshold list, select one of the following options:
Table 4-8 Blinding Threshold Values
Value To detect …
High (80%) Maximum blinding. The alarm message appears when your
camera is blinded by 80% or more.
Medium (50%) Medium blinding. The alarm message appears when your
camera is blinded by 50% or more.
Low (30%) Minimum blinding. The alarm message appears when your
camera is blinded by 30% or more.
3. Click Apply.
Note To turn off camera blind detection, select Disable in the Blinding Threshold
list. Disable is the default value.
Note You must click Apply after you make changes to any settings to save those
changes. Settings are not saved unless you click Apply.
56
Page 57
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Configuring Camera Field of View Change Detection
The web client application can detect tampering of the camera field of view and show an
alarm message above the video display (see Figure 4-14). To detect a change in the
camera field of view:
1. Click the Video Analytics tab.
2. In the Scene Change Threshold list, select one of the following options:
Table 4-9 Scene Change Threshold Values
Value To detect …
High (80%) Maximum change in the camera field of view. The alarm
message appears when tampering causes at least an 80%
change in your camera field of view.
Medium (50%) Medium change in the camera field of view. The alarm
message appears when tampering causes at least a 50%
change in your camera field of view.
Low (30%) Minimum change in the camera field of view. The alarm
message appears when tampering causes at least a 30%
change in your camera field of view.
3. Click Apply.
Note To turn off camera field of view change detection, select Disable in the Scene
Change Threshold list. Disable is the default value.
Note You must click Apply after you make changes to any settings to save those
changes. Settings are not saved unless you click Apply.
Configuring Video Motion Detection
For motion detection, an Administrator can enable and configure up to 5 zones within a
scene. The enabled and configured zones will be monitored for motion.
1. Click the Region drop-down menu, then select a region from the five available.
2. Click the VMD drop-down arrow, and select Enable.
The Regions appear in their default positions.
3. Click Apply.
Document 800-07067V4 Rev A 57
11/2011
Page 58
IP Camera Web Client
Region-defining box
4. Click and drag the box to resize and place it over the camera image.
5. Select the sensitivity level (High, Medium, Low).
Figure 4-15 Video Analytics: Defining a Region
Note To disable a zone, click the VMD drop-down menu, then select Disable.
58
Page 59
Alarm and Audio
Figure 4-16 Audio and IO Settings Tab
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Alarm Settings
Audio Settings
Connect external devices such as sirens or flashing lights to the alarm output connector to
signal camera users that an alarm is activated. Set the Alarm Output as Normally Open or
Normally Close. See Connecting Alarms on page 23 for more information.
When alarm inputs are connected, the camera triggers an alarm only when the normal state
(open or closed) changes. An alarm message appears on the web client screen (see
Figure 4-14) to notify the operator.
The network camera supports bi-directional audio. There are two supported voice band
channels that function in full duplex mode. Connect industry-standard line level audio input
and output to the back of your camera. See Connecting Audio on page 24 for more
information.
Audio configuration for your network camera is straightforward.
Document 800-07067V4 Rev A 59
11/2011
Page 60
IP Camera Web Client
Figure 4-17 Audio Settings
To listen to or capture audio from the camera, enable the Camera to Client (PC) check box
( ). To listen to audio from the client (PC), enable the Client (PC) to
Camera check box.
60
Page 61
A
Troubleshooting
Technical Support
Prior to calling Honeywell technical support, refer to the following topics for possible
solutions to problems with your network camera. To contact the Honeywell Video
Systems technical support team, call 1-800-796-2288 (North America only) or send an
e-mail to HVSsupport@honeywell.com.
Any equipment returned to Honeywell Video Systems for warranty or service repair must
have a Return Merchandise Authorization (RMA) number. The RMA number must be
clearly marked on all return packages and internal paperwork.
Problem: Failure of IP Utility Software Installation
Solution 1 Disable Norton AntiVirus software, then install the IP Utility software.
Solution 2 Enable Microsoft .NET Framework 3.5 on your workstation. It usually comes
pre-installed on Windows 7.
Enabling Microsoft .NET Framework 3.5 on Your Workstation
1. Go to Start Control Panel Programs Programs and Features.
2. Click the check box beside Microsoft .NET Framework 3.5 to enable it.
3. Click OK to save the new setting.
Document 800-07067V4 Rev A 61
11/2011
Page 62
Troubleshooting
Problem: Web Client Does Not Display the Expected Video
Possible solutions:
• Ensure that your web browser settings have been configured to allow ActiveX controls
(see Step 5: Launch the Web Client to View Live Video on page 35 for information on
setting up your browser).
• Ensure that the network cable from the camera is connected to both the camera and
the network.
Problem: Cannot Connect to a Device
When the following message (Figure A-1) displays in the status bar of the IP Utility, your
device connection is limited. Usually this warning state indicates that your PC and the
device you are connecting to are on different subnets. Contact your network administrator
for help to resolve your network issue(s).
Figure A-1 Limited or No Connection Message
62
Page 63
B
HCD5HIH Specifications
Note These specifications refer to all models, except where otherwise noted.
Specifications are subject to change without notice.
Video Signal Specifications NTSC PAL
Scanning System: Progressive
Image Sensor: 1/2.7” CMOS
Number of Pixels (H x V): 1920 x 1080 (HD)
Minimum Illumination: 0.15 lux color @ 50 IRE, F1.2
Video Output (local): 1.0 Vp-p @ 75 Ohms
S/N Ratio: 50 dB or more (AGC Off)
Auto Gain Control (AGC): Off/On, selectable (20 – 40 dB)
Auto Electronic Shutter (ELC): 1/30 – 1/24,000 sec 1/25 – 1/24,000 sec
Automatic Lens Iris Control: DC Iris level 1 – 25
White Balance (AWB): AWC, MWB (Manual Mode), AWC Push
Audio Signal Specifications
Audio/Two-Way: Line in/out
Electrical Specifications
Input Voltage: 24V AC, PoE IEEE 802.3af
Input Voltage Range: 17 – 28V AC
Surge Suppression: 1.5 kW transient
Power Consumption: 5 W (max)
Mechanical
Dimensions (WxH): See diagrams on page 65
Weight: 1.1 lb (0.5 kg) camera only
Construction: Housing: Aluminum
Connectors: Local Video Output: BNC
Environmental
Temperature: Operating: -22°F to 140°F (-30°C to 60°C)
Relative Humidity: 0% to 85%, non-condensing
Finish: Cool gray powder coat
Lens: 4-Pin Connector
Power Input: Removable screw terminal block
Alarm I/O: Removable screw block
Audio In: 3.5 mono phone jack
Audio Out: 3.5 mono phone jack
Network: RJ45 connector
Storage: -40°F to 158°F (-40°C to 70°C)
Document 800-07067V4 Rev A 63
11/2011
Page 64
HCD5HIH Specifications
IP Specifications
Video Compression: H.264, MJPEG
Primary Stream
Resolutions:
1920 x 1080
1280 x 720
800 x 450
640 x 360
320 x 180
Secondary Stream
Resolutions:
640 x 360
320 x 180
Software Update: Field Upgradeable
Frame Rate NTSC/PAL: Up to 30/25 fps video in all resolutions
Video Streaming: Dual Streaming: H.264 and MJPEG
Controllable frame rate and bandwidth
Security: Multiple user access levels with password protection
Video access from web
browser:
Minimum web browsing
requirements:
Camera live view for 1 client. Full control of all camera
settings available to administrator
Pentium IV CPU 3.1 GHz or faster
1 GB RAM (32-bit) or 2 GB RAM (64-bit)
Windows XP
®
, Windows 7 (32/64), Windows 2K8
(32/64), or WINServer 2003
Internet Explorer 6,7, or 8
Installation, Management, and
Maintenance:
Honeywell IP Utility software identifies the IP address,
checks the status of the device. Firmware upgrades over
HTTP, firmware available at www.honeywellvideo.com.
Supported Protocols: HTTP, TCP, RTSP, RTP, UDP, ARP, DNS, RTCP, FTP,
ICMP, DHCP, Bonjour, IGMP, Telnet
Regulatory
EMC 2004/108/EC
Emissions: EN 55022
Immunity: EN 50130-4
Safety: GPSD: 2001/95/EC
UL 60905-1; CSAC22.2 No.60950-1
64
Page 65
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
5.34” (135.6 mm)
0.81” (20.6 mm)
2.44” (62.0 mm)
2.44” (62.0 mm)
Figure B-1 Camera Dimensions
Document 800-07067V4 Rev A 65
11/2011
Page 66
HCD5HIH Specifications
66
Page 67
C
HCD5MIH Specifications
Note These specifications refer to all models, except where otherwise noted.
Specifications are subject to change without notice.
Video Signal Specifications NTSC PAL
Scanning System: Progressive
Image Sensor: 1/4” CMOS
Number of Pixels (H x V): 1280 x 720 (HD)
Minimum Illumination: 0.15 lux color @ 50 IRE, F1.2
Video Output (local): 1.0 Vp-p @ 75 Ohms
S/N Ratio: 50 dB or more (AGC Off)
Auto Gain Control (AGC): Off/On, selectable (20 – 40 dB)
Auto Electronic Shutter (ELC): 1/30 – 1/24,000 sec 1/25 – 1/24,000 sec
Automatic Lens Iris Control: DC Iris level 1 – 25
White Balance (AWB): AWC, MWB (Manual Mode), AWC Push
Audio Signal Specifications
Audio/Two-Way: Line in/out
Electrical Specifications
Input Voltage: 24V AC, PoE IEEE 802.3af
Input Voltage Range: 17 – 28V AC
Surge Suppression: 1.5 kW transient
Power Consumption: 5 W (max)
Mechanical
Dimensions (WxH): See diagrams on page 69
Weight: 1.1 lb (0.5 kg) camera only
Construction: Housing: Aluminum
Connectors: Local Video Output: BNC
Environmental
Temperature: Operating: -22°F to 140°F (-30°C to 60°C)
Relative Humidity: 0% to 85%, non-condensing
Finish: Cool gray powder coat
Lens: 4-Pin Connector
Power Input: Removable screw terminal block
Audio In: 3.5 mono phone jack
Audio Out: 3.5 mono phone jack
Network: RJ45 connector
Storage: -40°F to 158°F (-40°C to 70°C)
Document 800-07067V4 Rev A 67
11/2011
Page 68
HCD5MIH Specifications
IP Specifications
Video Compression: H.264, MJPEG
Primary Stream
Resolutions:
1280 x 720
800 x 450
640 x 360
320 x 180
Secondary Stream
Resolutions:
640 x 360
320 x 180
Software Update: Field Upgradeable
Frame Rate NTSC/PAL: Up to 30/25 fps video in all resolutions
Video Streaming: Dual Streaming: H.264 and MJPEG
Controllable frame rate and bandwidth
Security: Multiple user access levels with password protection
Video access from web
browser:
Minimum web browsing
requirements:
Camera live view for 1 client. Full control of all camera
settings available to administrator
Pentium IV CPU 3.1 GHz or faster
1 GB RAM (32-bit) or 2 GB RAM (64-bit)
Windows XP
®
, Windows 7 (32/64), Windows 2K8
(32/64), or WINServer 2003
Internet Explorer 6,7, or 8
Installation, Management, and
Maintenance:
Honeywell IP Utility software identifies the IP address,
checks the status of the device. Firmware upgrades over
HTTP, firmware available at www.honeywellvideo.com.
Supported Protocols: HTTP, TCP, RTSP, RTP, UDP, ARP, DNS, RTCP, FTP,
ICMP, DHCP, Bonjour, IGMP, Telnet
Regulatory
EMC 2004/108/EC
Emissions: EN 55022
Immunity: EN 50130-4
Safety: GPSD: 2001/95/EC
UL 60905-1; CSAC22.2 No.60950-1
68
Page 69
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
5.34” (135.6 mm)
0.81” (20.6 mm)
2.44” (62.0 mm)
2.44” (62.0 mm)
Figure C-1 Camera Dimensions
Document 800-07067V4 Rev A 69
11/2011
Page 70
HCD5MIH Specifications
70
Page 71
D
HCD5WIH Specifications
Note These specifications refer to all models, except where otherwise noted.
Specifications are subject to change without notice.
Video Signal Specifications NTSC PAL
Scanning System: Progressive
Image Sensor: 1/3” CMOS
Number of Pixels (H x V): 1280 x 720 (HD)
Minimum Illumination: 0.15 lux color @ 50 IRE, F1.2
Video Output (local): 1.0 Vp-p @ 75 Ohms
S/N Ratio: 50 dB or more (AGC Off)
Auto Gain Control (AGC): Off/On, selectable (20 – 40 dB)
Auto Electronic Shutter (ELC): 1/30 – 1/24,000 sec 1/25 – 1/24,000 sec
White Balance (AWB): AWC, MWB (Manual Mode), AWC Push
Audio Signal Specifications
Audio/Two-Way: Line in/out
Electrical Specifications
Input Voltage: 24V AC, PoE IEEE 802.3af
Input Voltage Range: 17 – 28V AC
Surge Suppression: 1.5 kW transient
Power Consumption: 5 W (max)
Mechanical
Dimensions (WxH): See diagrams on page 73
Weight: 1.1 lb (0.5 kg) camera only
Construction: Housing: Aluminum
Connectors: Local Video Output: BNC
Environmental
Temperature: Operating: -22°F to 140°F (-30°C to 60°C)
Relative Humidity: 0% to 85%, non-condensing
Finish: Cool gray powder coat
Lens: 4-Pin Connector
Power Input: Removable screw terminal block
Audio In: 3.5 mono phone jack
Audio Out: 3.5 mono phone jack
Network: RJ45 connector
Storage: -40°F to 158°F (-40°C to 70°C)
Document 800-07067V4 Rev A 71
11/2011
Page 72
HCD5WIH Specifications
IP Specifications
Video Compression: H.264, MJPEG
Primary Stream
Resolutions:
1280 x 720
800 x 450
640 x 360
320 x 180
Secondary Stream
Resolutions:
640 x 360
320 x 180
Software Update: Field Upgradeable
Frame Rate NTSC/PAL: Up to 30/25 fps video in all resolutions
Video Streaming: Dual Streaming: H.264 and MJPEG
Controllable frame rate and bandwidth
Security: Multiple user access levels with password protection
Video access from web
browser:
Minimum web browsing
requirements:
Camera live view for 1 client. Full control of all camera
settings available to administrator
Pentium IV CPU 3.1 GHz or faster
1 GB RAM (32-bit) or 2 GB RAM (64-bit)
Windows XP
®
, Windows 7 (32/64), Windows 2K8
(32/64), or WINServer 2003
Internet Explorer 6,7, or 8
Installation, Management, and
Maintenance:
Honeywell IP Utility software identifies the IP address,
checks the status of the device. Firmware upgrades over
HTTP, firmware available at www.honeywellvideo.com.
Supported Protocols: HTTP, TCP, RTSP, RTP, UDP, ARP, DNS, RTCP, FTP,
ICMP, DHCP, Bonjour, IGMP, Telnet
Regulatory
EMC 2004/108/EC
Emissions: EN 55022
Immunity: EN 50130-4
Safety: GPSD: 2001/95/EC
UL 60905-1; CSAC22.2 No.60950-1
72
Page 73
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
5.34” (135.6 mm)
0.81” (20.6 mm)
2.44” (62.0 mm)
2.44” (62.0 mm)
Figure D-1 Camera Dimensions
Document 800-07067V4 Rev A 73
11/2011
Page 74
HCD5WIH Specifications
74
Page 75
E
Glossary
AGC (Automatic Gain Control) Video Amplifier in a camera that boosts the amount of
video gain (including the noise) to maintain a 1V p-p (1-volt peak-to-peak) video signal
output. It becomes operational when the light level is low. The circuit is designed to
compensate for fluctuations in scene illumination which would cause the video output
level to be too low. If the video level (scene illumination) is adequate, the circuit does not
apply any gain to the signal. As the video level falls, more gain is applied by the AGC
circuit to the video signal.
ALC (Automatic Light Compensation) Setting in an Auto Iris lens to control the iris
opening.
DHCP (Dynamic Host Configuration Protocol) Allows a server to dynamically assign
IP addresses to nodes (workstations) automatically. Provides client information including
subnetwork mask, gateway address, and DNS (Domain Address Server) addresses.
DNR (Digital Noise Reduction) Reduces the appearance of noise in low-light
conditions.
DSS (Digital Slow Shutter) Improves picture quality (brightness) in low-light scenes.
DSS might introduce motion blur. The higher the DSS setting, the more likely motion blur
will occur.
ELC (Electronic Light Control) Typically used with manual iris lenses. The image
brightness is controlled electronically by the camera through automatically adjusting
shutter speed for a properly exposed picture.
Flickerless Eliminates the “flicker” that can appear in an image under certain lighting
conditions (for example, fluorescent lighting). This is usually caused by the interaction of
the shutter with the AC frequency of the lighting.
FOV (Field of View) The part of the scene visible with a particular lens. The height
(horizontal) and width (vertical) picture size at a given distance that can be seen through
a lens. Generally, shorter focal length lenses have a wider field of view than those with
longer focal lengths.
Gain The amplification a system provides to a signal.
IP Address A unique, 32-bit identifier for a specific TCP/IP host computer on a network.
Iris Adjust Adjusts the iris to either open or close in response to changing light
conditions.
NTSC (National Television Standards Committee) A standard of specifications for
television transmission in the U.S., Canada, Japan, Central American, and half of South
America. The North American system uses interlaced scans and 525 horizontal lines per
frame at 30 frames per second.
Document 800-07067V4 Rev A 75
11/2011
Page 76
Glossary
PAL (Phase Alternate Line) A standard of specifications for television transmission for
color TV signals used in West Germany, England, Holland, Australia, and several other
countries. It uses an interlaced format with 625 lines per frame at 25 frames per second.
PoE (Power over Ethernet) A method of powering Ethernet-connected devices via the
Ethernet cabling as defined in the IEEE 802.3af standard.
Shutter Speed The speed at which the charge is read out from the imager chip. Adjusts
the light sensitivity of the camera. A faster (briefer) shutter speed can arrest the motion of a
fast moving object (reduce image blur), rendering it sharp. Fast shutter speeds allow less
light to all on the CCD and can darken the image. For fast shutter speeds, ensure there is
adequate lighting. Usually selected using DIP switches on the side of the camera.
Subnet Mask A number used to identify a subnetwork so that an IP address can be shared
on a LAN.
True Day/Night The incorporation of a moving mechanical IR filter within the camera
ensures true 24 hour surveillance, providing high quality color images during the day and
similar quality black & white images at night when used with IR lighting.
UPS (Uninterruptible Power Supply) These are power supplies used in the majority of
high security systems, whose purpose is to back up the system when the main power fails.
76
Page 77
Index
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
A
ActiveX control 36
administrator
privileges 26
administrator password, default 29
AGC (Automatic Gain Control) 52
AGC (automatic gain control) 52
alarm configuration 59
alarm output settings 59
alarm settings 59
ALC (automatic light compensation) 52
APIPA address 33, 34, 46
audio configuration 59
audio settings 59
auto
configuration, IP network 32–34
device discovery 29, 34
log out, IP Utility 35
auto exposure settings 51
Auto White Balance Control mode 53
Automatic Gain Control 52
Automatic Light Compensation 52
AWC (auto white balance control mode) 53
B
bit rate 48, 49
setting 47, 49
viewing statistics 50
blinding threshold 54, 56
blur threshold 54, 55
Bonjour software 27
C
camera
type 45
camera blinding 56
camera field of view change 57
camera settings
AGC 52
ALC 52
AWC 53
DayToNight 53
detect time 52
flickerless 52
MWB 53
NightToDay 53
compression ratio, setting 47
compression settings 47, 48
bit rate 49
frame rate 49
GOP (group of pictures) 50
maximum bit rate 49
picture quality 50
target bit rate 50
configuration
alarm 59
audio 59
configuring
IP network settings 32–34
connect button 31
connecting
to devices 32, 40
D
DayToNight 53
default
passwords 29
default gateway 33
device
connecting 32
disconnecting 32
discovering 29, 34
information tab 45
name 33
DHCP address 33, 34, 46
digital noise reduction 52
digital slow shutter 52
disconnect button 31
disconnecting, from IP Utility 32
DNR 52
DSS 52
Document 800-07067V4 Rev A 77
11/2011
Page 78
E
EQUIP series
manuals 28
web client and 35, 40
IP Utility, logging onto 29
L
F
features, camera 16
field of view change 57
finding installed user manuals 29
firmware
settings 45
upgrading 31
flickerless 52
frame rate 48, 49
setting 47
viewing statistics 50
functions, camera 18
G
gateway 33, 46
GOP (group of pictures) 48, 50
group of pictures (GOP) 50
guest password, default 29
guest user privileges 26
H
HTTP server 30
I
installed components 27
IP
address 33, 34, 46
APIPA 33
DHCP 33
network settings 32–34, 45
IP address 33
IP network settings 32
default gateway 33
IP address 33
MAC address 33
subnet mask 33
IP Utility
description 25
disconnecting 32
discovering devices 29, 34
installing 28
interface overview 31
logging on 29
logging out 35
uninstalling 37
user types 26
LAN 27
launch web client 31, 35, 40
launching an IP web client 40
launching the IP Utility 29
limited/no connectivity button 31, 32
live view tab
layout 43
log off from the IP web client 42
logging onto an IP web client 40
logging onto the IP Utility 29
M
MAC address 33, 34, 46
manual white balance mode 53
manual, configuration, IP network 32–34
maximum bit rate 49
maximum bit rate, setting 47
motion detection 57
MWB (manual white balance) mode 53
N
netmask 33
NightToDay 53
NTSC
video format 46
video resolution 48
NTSC, video resolution 50
O
opening an IP web client 40
operating system 27
P
PAL
video format 46
video resolution 48
PAL, video resolution 50
password
defaults 29
picture quality 48, 50
priority 47
priority order
quality or bit rate 48
processor 27
profiles, user 26
78
Page 79
HCD5 EQUIP® Series True Day/Night Network Box Camera Reference Guide
Q
quality 49
quality priority setting 50
R
RAM 27
refresh button 31
resolution 48
resolution, setting 47
S
scene change threshold 54, 57
security settings, ActiveX 36
setting
IP network 31
settings
alarm 59
audio 59
auto exposure 51
software
downloading from website 25, 28
installing 27, 28
uninstalling 37
version 31
start menu 27
statistics
frame rate 50
received bit rate 50
statistics, viewing bit rate 50
statistics, viewing frame rate 50
subnet mask 33, 46
system requirements 27
T
tamper detection 55
target bit rate 48, 50
target bit rate, setting 47
thresholds, video analytics 54
U
uninstalling, software 37
upgrading firmware 31
user manuals, how to find installed 29
user profiles 26
V
video
analytics tab 54
format 46
viewing live 43
video analytics 54
blinding threshold 56
blur threshold 55
camera blinding 56
field of view change 57
motion detection 57
sabotage detection
sabotage detection 55
scene change threshold 57
tamper detection 55
video blurring 55
video blurring 55
video motion detection 57
VMD 57
W
web browser 27
web client
compression settings 47
launching and logging on/off 35
user types 26
web-client
description 26
website 25, 28
Document 800-07067V4 Rev A 79
11/2011
Page 80
80
Page 81
Page 82
Honeywell Systems (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywellvideo.com
+1.800.796.2288
Honeywell Security Northern Europe
Ampèrestraat 41
1446 TR Purmerend, The Netherlands
www.honeywell.com/security/nl
+31.299.410.200
Honeywell Security Europe/South Africa
Aston Fields Road, Whitehouse Industrial Estate
Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
+44.01928.754028
Honeywell Systems Caribbean/Latin America
9315 NW 112th Ave.
Miami, FL 33178, USA
www.honeywellvideo.com
+1.305.805.8188
Honeywell Systems Pacific
Level 3, 2 Richardson Place
North Ryde, NSW 2113, Australia
www.honeywellsecurity.com.au
+61.2.9353.7000
Honeywell Systems Asia
35F Tower A, City Center, 100 Zun Yi Road
Shanghai 200051, China
www.asia.security.honeywell.com
+86 21.5257.4568
Honeywell Security Middle East/N. Africa
Post Office Box 18530
LOB Building 08, Office 199
Jebel Ali, Dubai, United Arab Emirates
www.honeywell.com/security/me
+971.04.881.5506
Honeywell Security Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
www.honeywell.com/security/de
+49 74 31 / 8 01-18 70
Honeywell Security France
Immeuble Lavoisier
Parc de Haute Technologie
3-7 rue Georges Besse
92160 Antony, France
www.honeywell.com/security/fr
+33.(0).1.40.96.20.50
Honeywell Security Italia SpA
Via della Resistenza 53/59
20090 Buccinasco
Milan, Italy
www.honeywell.com/security/it
+39.02.4888.051
Honeywell Security España
Avenida de Italia, n° 7
P.I. - C.T.C. Coslada
28821 Coslada, Madrid, Spain
www.honeywell.com/security/es
+34.902.667.800
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
Document 800-07067V4 – Rev A – 11/2011
© 2011 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot
assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change
without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Loading...