Honeywell HCC-745PTW, HCC-745NTW Operation Manual

-1 -

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance(servicing) instructions in th e literature
accompanying the appliance.

OPERATION MANUAL

OSD COLOR CAMERA

with BMB (Black Mask BLC)

HCC-745N/P Series

READ AND KEEP THIS OPERATION MANUAL

-2 -

Warning:
This equipment generates and uses radio frequency energy
and if not installed and used properly, I.e., in strict accordance
with the instruction manual, may cause harmful interference
to radio communications. It has been tested and found to comply
with the limits for a Class A computing device pursuant to Subpart
J of Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.

Warning:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
PREFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

Indicate a potentially hazardous situation which if not avoided,
may result in minor or moderate injury. It may also be used to
alert against unsafe practices.

-3 -

CAUTION FOR SAFE OPERATION

1. Water and Moisture

To prevent fire or shock hazard, do not expose this camera

to rain or moisture.

2. Servicing

Do not attempt to disassemble or repair by yourself.
You may be exposed to dangerous voltage or other hazards.
Note that all servicing is qualified service personnel.
Modifications not approved by manufacturer could
void the user's authority to operate the equipment.

3. Power Sources

To prevent electric shocks and risk of hazards, do NOT use
more than the specified power source.

4. Environment

Do not install too warm or too cold place. Recommended
operation temperature is between -5℃ and 60℃

5. Sunlight

Do not point the camera at the sun. CCD can be damaged.

6. Heavy Shock and Vibration

Do not drop the camera or subject it to heavy shock of
vibration.

7. Install on an Unstable Place

Do not place or install this camera on an unstable place,
stand, tripod, bracket or table. That may cause serious injury
to people or damage to appliance.

8. When operation is incorrect or a malfunction is obs erved

While operating, if any abnormal condition (strange sound,
smell or smoke) or a malfunction (no pictures, etc.) is
observed, stop using the camera immediately, turn the
power off, then contact your supplier.

9. Cleaning

Turn the power off and wipe off the dirt with a dry soft
cloth. If it is extremely dirty, use furniture cleaner to wipe it
off. To clean the lens, use a blower or lens cleaning
tissue. (available from any camera dealer)

10. Do not shoot any source of bright light.

If the objects contain very bright areas, bright vertical or
horizontal lines may appear on the screen. This is called
"smear" , a Phenomenon which often occurs with solid

- state pickups, and is not a malfunction.

11. Damage Requiring service

Unplug the camera from the power source and refer
servicing to qualified service personnel under the following
condition:

a. If the power-supply cord or plug is damaged.
b. If the camera has been exposed to rain or water.
c. If liquid has been spilled, or objects have fallen into the camera.
d. If the camera does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a

qualified technician to restore the camera to its normal operation.
e. If the camera has been dropped or the cabinet has been damaged.
f . If the camera exhibits a distinct change in performance.

-4 -

CONTENTS

1. Features -------------------------------------------------------------- 5

2. Names & Functions ---------------------------------------------- 6

5. On Screen Display -------------------------------------------------- 11

Thank you for using this OSD Color Camera with BMB. To get the best
efficiency, read carefully all instructions in this manual before use, and
keep this manual for reference. If you have any problems with this camera,
contact your supplier to service.

4. Camera Control Methods------------------------------------------ 10

7. Dimensions ---------------------------------------------------------- 17

6. Specifications-------------------------------------------------------- 16

3. Installation----------------------------------------------------------- 8

-5 -

1. Features

Honeywell’s HCC-745N/P Series is a high sensitivity CCD color camera with high sensitivity function
of the field integration technique.

▣ 1/3” IT Super HAD CCD ( NTSC: 410,000 / PAL: 470,000 )
▣ Outstanding BLC implementation with Honeywell’s BMB(Black Mask BLC) function.

( 4 steps available : OFF / White / Gray / Black)

▣ Adapted CS/C mount lens adjustable.
▣ Excellent signal-to-noise ratio of more than 50dB.
▣ High Sensitivity : Minimum illumination of 0.001lx ( F1.2, 30IRE, SENS On X 128 )
▣ 2-WAY Auto Iris : Video iris or DC iris lens can be used.

▣ OSD Control :

Flickerless, AGC, Manual shutter control, Maximum Sensitivity select,
BMB Level, BLC Level, Title and Camera ID setting, Sync Mode

▣ External synchronization with LINE LOCK and Auto Detection.
▣ Auto White Balance : Auto white balance realizes true color reproduction within various light sources.
▣ Remote Control through RS485 / RS232C

-. Camera ID : 0 ~ 255

-. Title : 10 characters

-. Camera ID & Title Display Position : Bottom Right, Bottom Left, Top Right, Top Left, No Display

-. AWB Mode : ATW, AWC, INDOOR, USER FIX, OUTDOOR, Fluorescent, MWB

-. BLC Mode : OFF, Low BL, Mid BL, High BL

-. BMB Mode : OFF, White, Gray, Black

-. ELC / ALC Mode : ELC (AUTO/Manual), ALC (VSD Lens/DC Lens, Level)

-. SENS Mode : OFF, FIX, AUTO

-. Max Fields Control : x2 ~ x128

-. Sync. Control : AUTO, Internal, LineLock (V.PH control)

-. Shutter Speed Control : 10 steps including Flickerless

-. Max AGC Control : OFF ~ 38dB

-6 -

LENS CONNECTOR

Connect Auto Iris Lens
plug

Set Screw

Loosen Locking Ring with a Phillips
screwdriver to adjust Mounting Ring

2. Names & Functions

C/CS Mount Adaptor

• C-Mount lens : Turn Counterclockwise

• CS-Mount lens : Turn Clockwise

-7 -

POWER ON LAMP

In power ON state , this LED is ON .

VIDEO OUTPUT

This is the output terminal
for composite video signal

CAMERA CONTROL CONNECTOR

This is the 4 pin connector for external camera controls.
( Refer to 4. Camera Control Methods )

POWER INPUT

TERMINAL

(+) BUTTON

(UP) BUTTON

(-) BUTTON

MENU BUTTON

(DOWN) BUTTON

Lens Type Select Switch

DC Lens : with no iris amp.
VSD Lens : with iris amp.

-8 -

3.2 Mounting a Lens

3.2.1 C/CS Mount Lens

① Remove the protective cap in front of the camera.
② Adjust the mount ring whether it is for C or CS.

③ Loosen Set Screw with a Phillips screwdriver.
④

Turn the mount ring counterclockwise in case of C-Mount Lens.

Turn the mount ring clockwise in case of CS-Mount Lens

3.2.2 Auto Iris Lens

① Remove the cover of the iris lens plug and connect with Lens cable.

3. Installation

3.1 Check all accessories with enclosed package .

-. HCC-745N/P SET

-. 4 PIN CONNECTION CABLE ( G-111303-200 )

-. OPERATION MANUAL ( G-111304-001 )

-. Auto Iris Lens Plug

VSD LENS PIN CONFIGURATION

1

2

3

4

①

③
④②

1. POWER(12V) 2. NO CONNECTION

3. VIDEO SIGNAL 4. GND
Set the select switch to VSD

DC IRIS LENS PIN CONFIGURATION

1

2

3

4

①

③
④②

1. CONTROL- 2. CONTROL+

3. DRIVE+ 4. DRIVE­Set the select switch to DC

* For the best condition, read lens manual carefully .

-9 -

3.4 Connection of POWER supply

☞ Must be checked the power source from the external power supply before power on.
☞ Power source capacity : AC 24V, more than 500mA (Recommended Honeywell HAC-2450)

DC 12V, more than 500mA (Recommended Honeywell HDC-1260R)

② Connect the Lens plug to the Lens connector (SIDE PART)
③ EE MODE must be set to ALC MODE on OSD menu ( Refer to. 5.7 )

-. In the case of having no iris amplifier : Set DC LENS on OSD menu
☞ If using DC lens, “LEVEL” of DC LENS on OSD menu must be adjust carefully.

It may cause any hunting.

-. In the case of having iris amplifier : Set VSD LENS on OSD menu

④Set the S/W on the REAR of the camera to DC or VSD, too.

☞ When connecting Auto iris lens, be sure to use the connector to be recommended

by manufacturer. (E4-191, Chuo Musen, Japan)

☞

After connecting Auto iris-lens you may need to set flange back focus.

3.3 Flange back focus adjustment

3.3.1 In case of fixed focus lens
a. Loosen the Set Screw and set the focus ring of lens to infinity ( ∞ ).
b. Tune the mount adapter to get a clear picture( distance from camera to object is more than 23m)

and fasten the Set Screw.

3.3.2 In case of zoom lens
a. Loosen the Set Screw and set the lens to the maximum telephoto position.

Then turn the focus ring to focus.

☞ in the case of Auto iris lens, shoot a comparatively dark object or reduce

the ambient light so that the Iris is fully open.
b. Set the lens to its maximum wide angle position, and set the focus.
c. Repeat step a and b, until the difference between focusing position a and b is smallest.
d. When the best focusing point is found, fasten the Set Screw.

-10 -

4.1 Remote Control using for RS-232C connection ( HCC-745N/P )

4. Camera Control Methods

Connect to Serial PORT
( COM1 or COM2 )

4P Cable

2
3
4

RD ( TxD )

TD ( RxD )

GND

4P Cable

Serial Cable

Serial Cable
( 9 Pin D-Sub )

2

RD

3

TD

5

SG

4
6

7
8

Connect internally
for communication

4.2 Remote Control using for RS-485 connec tion ( HCC-745N/P-VR )

Connect to Serial PORT
(COM1 or COM2)

4P Cable

Serial Cable

RS485 Converter

3
2

TRx +

TRx-

4P Cable

RS485 Converter

TRx+
TRx-

RS485

RS232C

1. Red : Not Use

2. Blue : RD(TxD)

3. Yellow : TD(RxD)

4. Black : GND

1. Red : Not Use

2. Blue : TRx-

3. Yellow : TRx+

4. Black : Not Use

-11 -

5. On Screen Display

<Fig5-1. Operating OSD display position>

5.1 How to display Operating OSD
a. Pressing the MENU key softly confirm current Operating OSD.

It is disappeared a few seconds later if there are no other key actions.

b. Even though Operating OSD is disappeared,

it keep displaying Camera ID or Title in screen.
In order to do not display ID, one method is to change EEPROM data
of Camera, the other is to use external communication through RS-232C.

c. Using RS-232C communication, change display position of ID;

Bottom Right -> Top Left -> Top Right -> Non display.

* If display Operating OSD is not needed by special purpose

like using external text overlay board, it can be OFF modeat all times

through external communication control as RS-232C, RS485.

③ ④ ⑤

①,②

①,② ①,②

①,②

Fluorescent mode (4200°K)FRS
User mode (4700°K)USR

Manual WB modeMWB

One Push modeAWC

1/500001/50000

1/300001/30000

1/100001/10000

1/40001/4000

1/20001/2000

1/10001/1000

1/5001/500

1/2501/250

Outdoor Preset (6300°K)OUT

Flickerless ON
( NTSC:1/120,PAL 1/100)

FL

Auto Trace White BalanceATWWB MODE

⑤

Indoor Preset (3200°K)IN

DESCRIPTIONOSD FormatFUNCTION

Normal Shutter
( NTSC:1/60 PAL :1/50 )

1/60 (1/50)Shutter

Speed

④

Back Light ONH.BL M.BL L.BL

Back Light OFFNon d isp layBack Light

③

Refer to. 5.7■■…■■TITLE

②

In case that ID is 0Non disp layCAMERA ID

①

In case that ID is 1 ~ 255ID : 002

-12 -

5.2 Display SETUP MENU

a. Press MENU key above 2 seconds so that SETUP MENU is displayed

on the screen.
b. Select item of SETUP MENU using UP / DOWN key.
c. (+) / (-) key is used to increase / decrease data of selected item.

5.3 Quit SETUP MENU
a. Press the MENU key again. SETUP MENU is disappeared,

“SAVE?” or “QUIT?” is displayed at center of screen.
If there is no change of adjustment state of Camera,
“QUIT?” is showed, else “ SAVE?” is showed.

① “QUIT?” : quit SETUP MENU without saving changed value.
② “SAVE?” : quit SETUP MENU with saving changed value.

b. Press (+) / (-) key to choose, and press the MENU key again.

whole SETUP MENU is quitted.

( If MENU key is not pressed and UP / DOWN key is pressed,

SETUP MENU is appeared again. )

5.4 Configuration of OSD MENU

5.5 SETUP MENU functions
① Camera ID

: Press (+) or (-) key to access Camera ID setup frame.

CAMERA ID OFF → 001 → . . . . → 255

② ELC / ALC Mode

: Press (+) or (-) key to access ELC/ALC Mode setup frame.

ELC / ALC ELC MODE → ALC MODE → . . . .

③ Shutter Speed Control

: You can adjust Brightness with high shutter speed.

( It doesn’t work on AUTO of ELC mode. )

SHUTTER 1/60(1/50) → FL → 1/250 →. . . .

④ White Balance Mode

: Press (+) or (-) key to access White Balance Mode setup frame.

WB CONTROL ATW → AWC → MWB →. . . .

⑤ Set Maximum AGC Gain

: You can adjust Maximum value of AGC Gain.

AGC CONTROL OFF → 10dB → 12dB →. . . . → 38dB →

<<SETUP MENU >>

①

CAMERA ID 002

② ELC / ALC ELC MODE
③ SHUTTER 1/60
④ WB CONTROL AWC
⑤ AGC CONTROL 34dB
⑥ SENS UP AUTO
⑦ MAX FIELD x128
⑧ SYNC. CONT. AUTO
⑨ INITIAL SET OFF

EXIT MENU

<Fig5-2. SETUP MENU >

Camera ID, Title
Display Position

ELC Mode : AUTO, MANUAL
ALC Mode : VSD LENS

DC LENS (LEVEL)

Shutter
Speed

ATW, Outdoor, Indoor,User,
Fluorescent ,
AWC(Auto, Manual;Push&Lock),
MWB(RED, BLUE)

AGC
Control
Sensitivity
Up

Max Field

AUTO, INTERNAL,
LineLock(V.PH)

Initial Set

SETUP
MENU

CAMERA
ID

ELC/ALC
Mode

White
Balance

Sync.
Control

Exit Menu

If SENS UP Mode is set to AUTO or FIX, you can adjust AGC
from 18dB ~ 38dB.

☞ Notes

-13 -

ⓖ Title

: It is the name of Camera. It enters 10 characters including blank.

TITLE: ■■■■■■■■■■

ⓗ Position

: You can choose the position to display Camera ID or Title.

POSITION:T.R. → B.R. → B.L. → T.L. → NO DISP . . . .

ⓘ Return

: To move the first SETUP frame.

⑥ Sens Up Mode

: Use for compensating the low illumination condition. In case that use

this function because of low illumination condition, adjust maximum
integration fields to get brighter and dynamical image. But the scene
becomes slower than OFF mode.

SENS UP OFF → AUTO → FIX → . . . .

⑦ Max Field Control

: The larger max fields is, simultaneously the noise of image is larger.

This is phenomenon because too small video output is integrated
on many fields memory. To get more dynamical image, adjust maximum
integration fields and set maximum AGC gain highly, then make better
the standard of dynamic image.

MAX FIELD OFF → x2 → x4 → x6 → x8 → x10

→ x16 → x 32 → x64 → x128 . . . .

⑧ Sync. System Mode

: Press (+) or (-) key to access Sync. System setup frame.

SYNC. CONT. AUTO → INTERNAL → LINELOCK → . . . .

⑨ INITIAL SET Mode

: Set the INITIAL SET Mode ON so that all changed data are returned to

shipping condition. Mode becomes OFF if SETUP MENU state is different
from shipping condition.

INITIAL SET OFF → ON → . . . .

< Fig 5-3. Camera ID setup frame >

ⓐ CAM ID : 002

ⓑ
ⓒ
ⓓ
ⓔ
ⓕ

ⓖ TITLE:HCC-745N■■
ⓗ POSITION:T.R.
ⓘ RETURN

0
G
X
n

;

2

I
Z
p

!

1
H
Y
o
~

7
N
e
u

*

3
J

a
q
?

4
K
b
r
#

5
L
c
s
$

6

M

d
t

%

8
P

f
v
&

9
Q
g
w

/

A
R
h
x
<

E
V

l
.

=

B
S

i
y
>

C
T

j

z

+

D
U
k

,

-

F
W
m

:

■

Using RS-232C, RS-485 Communication, you can choose the one
among Camera ID and Title which is displayed.

☞ Notes

Let’s enter the Title as “R1” , example

-. Select the position of title character by using (+) or (-) key.
The chosen position is blinking.

TITLE: □ ■■■■■■■■■

-. Select the character “R” among

ⓑ~ ⓕ

by using UP,DOWN,

(+),(-) key. The chosen character “R” is blinking.

-. Press MENU key, the character “R” is entered in the Title.

TITLE: R ■■■■■■■■■

-. Select the next position of title character by using (+) or (-) key.
The chosen position is blinking.

TITLE: R □ ■■■■■■■■

-. Select the character “7” among

ⓑ~ ⓕ

by using UP,DOWN,

(+),(-) key. The chosen character “7” is blinking.

-. Press MENU key, the character “7” is entered in the Title.

TITLE: R7 ■■■■■■■■

▣ How to Enter the Title ▣

7
N
e

8
P

f

9
Q
g

A

R

h

E
V

l

B
S

i

C
T

j

D
U
k

F
W
m

7

N
e

8
P

f

9
Q
g

A
R
h

E
V

l

B
S

i

C
T

j

D
U
k

F
W
m

5.6 Camera ID setup frame

ⓐ Camera ID

: It is the number assigned each Camera in case of

controlling many Cameras. It is from 0 to 255. But in case of 0, that is
not displayed on screen.

CAM ID : 000 ~ 255

-14 -

5.7 ELC/ALC MODE setup frame
ⓙ EE MODE

: You can select the Lens Type, Manual Lens or Automatic Lens.

♦ ELC MODE ( for Manual Lens )

-. AUTO : Iris operates electronic exposure automatically.

-. MANUAL : Adjust iris by changing high shutter speed manually.

♦ ALC MODE ( for Automatic Iris Lens )

-. VSD LENS : VSD type lens

-. DC LENS : DC type lens. Adjust “LEVEL”until the monitor picture
appears to be not too bright or too dark.

ⓚ Backlight Compensation MODE

: It prevents the center object too darken when the excessive light is behind

the center object.

BLC MODE : OFF → LOW BL → MID BL → HIGH BL → ….

ⓛ Black Mask BLC MODE

: It is another function of BLC. It mask the excessive light to dark level and

make brighter to see object around the excessive light.

BMB MODE : OFF → WHITE → GRAY → BLACK → ….

ⓜ Return

: To move the first SETUP frame.

< ELC / ALC MODE >

ⓙ EE MODE : ALC MODE

DC LENS
LEVEL 04

ⓚ BLC MODE : OFF
ⓛ BMB MODE : OFF

ⓜ RETURN

< Fig 5-4. ELC/ALC Mode setup frame >

If BLC Mode is set, BMB Mode will be cancelled.
If BMB Mode is set, BLC Mode will be cancelled.

☞ Notes

▣ BMB and BLC ▣

When excessive light is existed, overall image is seen dark.

When BLC is activated, overall image is seen bright strongly. .

When Camera mask the strong background light with BMB function,
the rest of image is seen clearly.

Normal AE operation

BLC operation

BMB operation

-15 -

5.8 White Balance Control setup frame
ⓝ WB MODE

♦ ATW ( Auto Trace White Balance Mode )

. It is the feedback system that automatically aligns the white balance.

( 2,800 ºK~ 8,000 ºK )

♦ AWC ( Auto White Balance Control Mode )

It performs more faster action than ATW mode without operating
range.

-. AUTO : AWC operates all the time.

-. MANUAL : PUSH – Press “MENU” key and start AWC operation.
LOCK – Release key to fit the present shooting scene.

♦ INDOOR ( 3200 ºK )
♦ FLUORESCENT ( 4200 ºK )
♦ USER FIXED ( 4700 ºK )
♦ OUTDOOR ( 6300 ºK )
♦ MWB ( MANUAL Mode )

-. RED : 0 ~20

-. BLUE : 0~20

ⓞ Return

: To move the first SETUP frame.

< White Balance >

ⓝ WB MODE : MWB

WB CONT : R=00

B=00

ⓞ RETURN

< Fig 5-5. WB Control setup frame >

5.9 Synchronization Control setup frame
ⓟ SYNC MODE

: It provides 3 Modes, Internal, LineLock and AUTO.

♦ INTERNAL
♦ LINELOCK

: You can adjust the proper phase with step.

-. V.PH : 000 ~ 300 (factory default : 0)

-. STEP : 00 ~ 50

♦ AUTO

: Camera detects sync. System automatically.

ⓠ Return

: To move the first SETUP frame.

< Sync. Control >

ⓟ SYNC MODE : LINELOCK

V.PH 000
STEP=10

ⓠ RETURN

< Fig 5-6. Sync. Control setup frame >

LINELOCK mode is not available in DC 12V power.

☞ Notes

-16 -

6. Specifications

OFF, White, Gray, BlackOFF, White, Gray, BlackBMB

C/CS MountC/CS MountLens Mount

EE, VSD, DCEE, VSD, DCALC

AC24V±20%, DC12V±2V, Max 3WAC24V±20%, DC12V±2V, Max 3WPower Source

-10℃ ~ +50℃-10℃ ~ +50℃Operating Temp.

-20℃ ~ +70℃-20℃ ~ +70℃Storage Temp.
380g380gWeight

OFF ~ 38dBOFF ~ 38dBAGC

1/50s ~1/50,000s ( 10 steps )1/60s ~1/50,000s ( 10 steps )Elec. Shutter

ATW, AWC, INDOOR, OUTDOOR, FLUORESCENT, USER, MWBWhite Balance

OFF, Low, Middle, HighOFF, Low, Middle, HighBLC

less than 0.1lx (F1.2, 30IRE, AGC ON)
SENS ON 0.001lx ( X128 fields )

less than 0.1lx (F1.2, 30IRE, AGC ON)
SENS ON 0.001lx ( X128 fields )

Min. illumination

more than 50dBmore than 50dBS/N Ratio

VBS 1.0Vp-p / BNCVBS 1.0Vp-p / BNCVideo out

480 TV Lines480 TV LinesH Resolution

15.625KHz(H), 50.0Hz(V)15.734KHz(H), 59.94Hz(V)Scanning frequency

Internal / Line lock / AutoInternal / Line lock / AutoSync system

68(W) * 56(H) * 120(D)68(W) * 56(H) * 120(D)Dimensions

625 Lines 2:1 Interlace525 Lines 2:1 InterlaceScanning system

752H * 582V (440,000pixels)768H * 494V (380,000pixels)Effective pixel

1/3” CCD (total 470,000pixels)1/3” CCD (total 410,000pixels)Imaging device

HCC-745PHCC-745NMODEL NAME

-17 -

7. Dimension

-18 -

MEMO

Printed in Korea

G-111304-001

Honeywell Co., Ltd.
Address : 17F, Kukje Center Building 191, Hankangro -2ga,

Yongsan-gu, Seoul 140-702, Korea

Phone : [phone], 6108, 6107, 6292
Fax : [phone]
http : //www.honeywell.co.kr/security/english
E-mail : [e-mail]