Page 1
Embedded NVR Bundle
IP Cameras
HBD2PR1
H2D2PR1
User Guide
Document 800-18161 – Rev A – 06/2014
Page 2
Page 3
User Guide
Page 4
Revisions
Issue Date Revisions
A 06/2014 New document.
Page 5
Cautions and Warnings
| 5
WARNING
intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,
on the unit, output rated 12 V DC, minimum 0.5A, Tma=60Deg.C or from Power over
Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE
802.3af PoE standard.
The Ethernet connection is not intended to be connected to exposed (outside plant)
networks. Do not connect two power sources to the camera at the same time.
CAUTION Invisible LED radiation (850 nm). Avoid exposure to beam.
Regulatory Statements
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
To ensure compliance with electrical safety standards this product is
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
800-18161 - A - 06/2014
Page 6
6 | Embedded NVR Bundle IP Cameras User Guide
Note Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Canadian Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Manufacturer’s Declaration of Conformance
North America
The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.
Europe
The equipment supplied with this guide meets the provisions of the following European Union
council directives:
• 2004/108/EC for EMC,
• 2001/95/EC for safety, and
• 2011/65/EU for RoHS compliance.
Waste Electrical and Electronic Equipment (WEEE)
Safety Instructions
Before installing or operating the unit, read and follow all instructions. After installation, retain the safety and operating instructions for future reference.
1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.
Correct Disposal of this Product (applicable in the European Union and other
European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
www.honeywell.com/security
Page 7
| 7
2. INSTALLATION
• Install in accordance with the manufacturer’s instructions.
• Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
• Any wall or ceiling mounting of the product should follow the manufacturer’s
instructions and use a mounting kit approved or recommended by the manufacturer.
3. POWER SOURCES - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supplied to your
facility, consult your product dealer or local power company.
4. MOUNTING SYSTEM - Use only with a mounting system recommended by the
manufacturer, or sold with the product.
5. ATTACHMENTS - Do not use attachments not recommended by the product
manufacturer as they may result in the risk of fire, electric shock, or injury to persons.
6. ACCESSORIES - Only use accessories specified by the manufacturer.
7. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
8. SERVICING - Do not attempt to service this unit yourself. Refer all servicing to qualified
service personnel.
9. REPLACEMENT PARTS - When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric
shock or other hazards. Using replacement parts or accessories other than the original
manufacturers may invalidate the warranty.
800-18161 - A - 06/2014
Page 8
8 | Embedded NVR Bundle IP Cameras User Guide
www.honeywell.com/security
Page 9
Contents | 9
Contents 1
Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Canadian Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Manufacturer’s Declaration of Conformance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Overview of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Overview of the Embedded NVR Bundle IP Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Features of the Embedded NVR Bundle IP Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Camera Dimensions and Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
H2D2PR1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
HBD2PR1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Starting the Honeywell Configuration Tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installing the Quick Configuration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Opening the Honeywell Configuration Tool, Searching for Devices, and Opening a Web Client . . . 30
Upgrading a Single IP Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Upgrading the IP Cameras (Batch Upgrade) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Modifying the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3 Web Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Main User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Live Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Video Encoder Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Configuring the Live View Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Video Window Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Image Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Original Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Full Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Width and Height Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Fluency Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
800-18161 - A - 06/2014
Page 10
10 | Embedded NVR Bundle IP Cameras User Guide
Camera Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Profile Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Video Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Video Bit Stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Video Overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Network Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
TCP/IP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
PPPoE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
IP Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
SMTP (Email) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Bonjour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Multicast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
IEEE802.1X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Video Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Tampering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Abnormality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Recording Schedule and Snapshot Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Record Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
General System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Import/Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Automatic Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Online User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Log Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Appendix A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Appendix B Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
www.honeywell.com/security
Page 11
Figures | 11
Figures 1
Figure 1-1 H2D2PR1 Camera Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 1-2 H2D2PR1 Camera Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 1-3 HBD2PR1 Camera Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 1-4 HBD2PR1 Camera Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 2-1 Honeywell Config Tool Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 2-2 User License Agreement Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 2-3 Installation is Complete Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 2-4 Configtool Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 2-5 ConfigTool Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 2-6 Device Upgrade Login Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 2-7 Config Upgrade Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 2-8 Device Offline Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 2-9 Upgrade Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 2-10 ConfigTool Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 2-11 Upgrade Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 2-12 Open Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 2-13 Upgrade Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 2-14 Batch Upgrade Progress Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 2-15 Batch Upgrade Successful Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 2-16 ConfigTool Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 2-17 Selecting Net in the ConfigTool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 3-1 Logging in through an IE Browser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 3-2 Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 3-3 First Time Login Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 3-4 File Download Security Warning Popup for the Plug-in. . . . . . . . . . . . . . . . . . . . . . 42
Figure 3-5 Internet Explorer - Security Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 3-6 Plug-in Installation Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 3-7 Plug-in Installation Progress Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 3-8 Live View Window Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 3-9 Video Encoder Setup Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 3-10 System Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 3-11 Live View Window Tool Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 3-12 Video Window Configuration Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 3-13 Image Adjustment Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 3-14 Camera Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
800-18161 - A - 06/2014
Page 12
12 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-15 Profile Management Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 3-16 Video Bit Stream Configuration Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 3-17 Snapshot Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 3-18 Video Overlay Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 3-19 Storage Path Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 3-20 TCP/IP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 3-21 Connection Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 3-22 PPPoE Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 3-23 DDNS Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 3-24 Using Honeywell DDNS to Configure DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 3-25 IP Filter Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 3-26 SMTP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Figure 3-27 UPnP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Figure 3-28 SNMP Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Figure 3-29 Bonjour Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Figure 3-30 Mulitcast Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 3-31 802.1X Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 3-32 QoS Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 3-33 Motion Detection - Video Detection Configuration Interface . . . . . . . . . . . . . . . . . . . 74
Figure 3-34 Configuring the Working Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 3-35 Configuring the Motion Detection Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 3-36 Tampering Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Figure 3-37 Tampering Working Period Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . .78
Figure 3-38 Disconnection Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Figure 3-39 IP Conflict Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Figure 3-40 Recording Schedule Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 3-41 Holiday Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure 3-42 Destination Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure 3-43 FTP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Figure 3-44 Record Control Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Figure 3-45 General System Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Figure 3-46 Date and Time Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Figure 3-47 Username Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Figure 3-48 Add User Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Figure 3-49 Modifying User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Figure 3-50 Group Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 3-51 Add Group Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 3-52 Modify Group Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 3-53 Default Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 3-54 Import/Export Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Figure 3-55 Auto Maintain Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Figure 3-56 Upgrade Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Figure 3-57 Version Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Figure 3-58 Log Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
F
igure 3-59 Online User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
. . . . . . . . . 91
www.honeywell.com/security
Page 13
Figures | 13
Figure 3-60 Alarm Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Figure 3-61 Log In Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
800-18161 - A - 06/2014
Page 14
14 | Embedded NVR Bundle IP Cameras User Guide
www.honeywell.com/security
Page 15
Tables | 15
Tables 1
Table 1-1 IP Cameras Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 1-2 H2D2PR1 Camera Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 1-3 HBD2PR1 Camera Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 3-1 Live View Window Sections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 3-2 Live View Window Sections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 3-3 Live View Window Tool Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 3-4 Video Window Configuration Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 3-5 Image Adjustment Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 3-6 Camera Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 3-7 Video Bit Stream Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 3-8 Snapshot Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 3-9 Video Overlay Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 3-10 TCI/IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Table 3-11 Connection Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 3-12 DDNS Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Table 3-13 Honeywell DDNS Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Table 3-14 SMTP (Email) Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Table 3-15 SNMP Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Table 3-16 Multicast Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Table 3-17 802.1X Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 3-18 QoS Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table 3-19 Video Motion Detection - Video Detection Configurations . . . . . . . . . . . . . . . . . . . . . 74
Table 3-20 Motion Detection Area Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Table 3-21 Tampering Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Table 3-22 Destination Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Table 3-23 Record Control Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Table 3-24 General System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 3-25 Date and Time Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 3-26 Import/Export Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Table 3-27 Log Interface Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Table 3-28 Alarm Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Table A-1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Table B-1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
800-18161 - A - 06/2014
Page 16
16 | Embedded NVR Bundle IP Cameras User Guide
www.honeywell.com/security
Page 17
About This Document
This document introduces the Honeywell Embedded NVR Bundle IP Cameras. It covers how to
install and operate the Embedded NVR Bundle IP Cameras.
This document is intended for installers and users.
Overview of Contents
This document contains the following chapters and appendixes:
• Chapter 1, Introduction, introduces the Embedded NVR IP Cameras, including
descriptions of their features and illustrations showing the cameras’ dimensions.
• Chapter 2, Configuration, describes the Quick Configuration tool and how to install it.
• Chapter 3, Web Operation, describes how to connect to your camera over the internet,
describes the user interface, and how to remotely configure and operate your camera.
• Appendix A, Troubleshooting, describes possible problems and their solutions.
• Appendix B, Specifications, provides the cameras’ specifications.
• Index, provides a searchable list for easy access to the document.
800-18161 - A - 06/2014
Page 18
18 | Embedded NVR Bundle IP Cameras User Guide
Related Documents
This document is a necessary prerequisite for understanding the Embedded NVR Bundle IP
Cameras. For more information, please refer to the following documents:
Document title Part number Description
Embedded NVR Quick Connection
Guide
Embedded NVR Quick Networking
Guide
H2D2PR1 1080p True Day/Night IR
Ball IP Camera Quick Installation
Guide
HBD2PR1 1080p True Day/Night IR
Bullet IP Camera Quick Installation
Guide
Embedded NVR User Guide 800-18160 Describes the embedded NVR, how to install it, how to
800-16860 Visually describes how to connect and start up an
Embedded NVR.
800-16861 Visually describes how to configure network
connections, including the mobile application.
800-17073 Describes the physical setup of a H2D2PR1 ball
camera.
800-17077 Describes the physical setup of a HBD2PR1 ball
camera.
configure it, and how to use it.
Typographical Conventions
This document uses the following typographical conventions:
Font What it represents Example
Helvetica
Lucida Values of editable fields that are mentioned in the
Swiss721 BT Bold Words or characters that you must type. The word
www.honeywell.com/security
Keys on the keyboard Press Ctrl+C
The Time from field can be set to
body text of the document for reference purposes,
but do not need to be entered as part of a procedure
Text strings displayed on the screen
Syntax
“enter” is used if you must type text and then press
Enter or Return key.
the
Menu titles and other items you select Double-click Open from the File menu.
Buttons you click to perform actions Click Exit to close the program.
Hours:Minute:Seconds.
The message Unauthorized displays.
(object) entered
Enter the password.
Page 19
Font What it represents Example
| 19
Italic Placeholders: words that vary depending on the
situation
Cross-reference to external source Refer to the Embedded NVR Quick
Cross-reference within document See Chapter 2, Configuration.
Enter your user name.
Installation Guide.
800-18161 - A - 06/2014
Page 20
20 | Embedded NVR Bundle IP Cameras User Guide
www.honeywell.com/security
Page 21
1
Introduction 1
This chapter covers:
• An overview of the Embedded NVR Bundle IP Cameras IP Cameras and their features.
Overview of the Embedded NVR Bundle IP Cameras
The Embedded NVR Bundle IP Cameras IP Cameras integrate the traditional camera with
network video technology, while combining video data collection and transmission. They can
directly connect to the network without any auxiliary device.
The Embedded NVR Bundle IP Cameras IP Cameras use standard H.264 video compression
technology, which guarantees maximum video quality.
Some of the Embedded NVR Bundle IP Cameras IP Cameras (H2D2PR1, HBD2PR1) support IR
night vision. At night or in dimly environments, these cameras can use IR light to illuminate the
scene. The waterproof design conforms to IP66 standards, making the Embedded NVR Bundle
IP Cameras suitable for use in outdoor environments.
The Embedded NVR Bundle IP Cameras can be used alone or used in a network. When not in
a system, you can connect them to the Internet and then use a Internet web client on your PC.
Due to their flexibility, the Embedded NVR Bundle IP Cameras IP Cameras can be used in many
environments to monitor offices, banks, or roads, for example.
800-18161 - A - 06/2014
Page 22
22 | Embedded NVR Bundle IP Cameras User Guide
Features of the Embedded NVR Bundle IP Cameras
Table 1-1 IP Cameras Features
Category Features
User Management • Different user rights for each group; each user belongs to
a specific group.
• User rights cannot exceed Group rights.
Storage • Supports central server backup in accordance with your
configuration and setup in Alarm or Schedule settings.
• Supports recording via the Internet. The recorded files are
stored on the client’s PC.
• Supports network storage, such as FTP.
Network Monitor • Cameras support one-channel video data transmission to
a network terminal, and the decoding of that data. The
Delay time is less than 270ms (network bandwidth
support is required).
• Supports a maximum of 20 connections.
• Compatible with the following transmission protocols:
HTTP, TCP, UDP, MULTICAST, RTP/RTCP, RTSP.
• Supports web access.
www.honeywell.com/security
Page 23
Introduction | 23
Table 1-1 IP Cameras Features
Category Features
Network Management • Supports network camera configuration and
management via the Ethernet.
• Supports device management via the Internet or through
the client’s PC.
Power • External 12 V DC adapter.
• Supports PoE.
WARNING Do NOT connect these two power sources to
the cameras at the same time. This could result in
damage to the camera.
Assistant Function • Log function.
• Supports system resource information and running status
real-time display.
• Supports Day/Night mode auto switch.
• Supports picture parameter setup such as electronic
shutter and gain setup.
• Supports motion detection.
• Supports backlight compensation: screen auto splits to
aid in configuring backlight compensation, which adjusts
to the scene brightness.
• Supports video watermark function to avoid video
modification.
• Built-in IR light. Supports IR night vision (depending on
the camera model).
• Enclosure conforms to IP66 protection. The cameras are
waterproof.
Camera Dimensions and Components
For camera specifications, please see Appendix B on page 97.
800-18161 - A - 06/2014
Page 24
24 | Embedded NVR Bundle IP Cameras User Guide
In millimeters
H2D2PR1
Dimensions
Figure 1-1 H2D2PR1 Camera Dimensions
Components
Figure 1-2 H2D2PR1 Camera Components
Table 1-2 H2D2PR1 Camera Components
Name Function
1 Lens
2 Dome body
www.honeywell.com/security
Page 25
HBD2PR1
In millimeters
Introduction | 25
Table 1-2 H2D2PR1 Camera Components
Name Function
3 Dome camera enclosure
4 LAN Network port to connect to standard Ethernet.
5 12 V DC Connect 12 V DC
Dimensions
Figure 1-3 HBD2PR1 Camera Dimensions
Components
Figure 1-4 HBD2PR1 Camera Components
800-18161 - A - 06/2014
Page 26
26 | Embedded NVR Bundle IP Cameras User Guide
Table 1-3 HBD2PR1 Camera Components
Name Function
1 LAN Network port to connect to standard Ethernet.
Note Before connecting to the RJ-45 port, pull the anti-dust cover
2 12 V DC Connect 12 V DC
over the network cable.
www.honeywell.com/security
Page 27
2
Configuration 2
This chapter includes:
• An overview of the Honeywell Configuration Tool.
• Installation procedures for the Honeywell Configuration Tool.
Overview
The Honeywell Configuration Tool can be used to:
• Search for the current IP address.
• Modify the current IP address.
• Upgrade the IP camera.
Note The Honeywell Configuration tool applies only to the IP addresses in the same
segment.
Starting the Honeywell Configuration Tool
You must install the Honeywell Configuration Tool before you can use it to discover IP devices.
800-18161 - A - 06/2014
Page 28
28 | Embedded NVR Bundle IP Cameras User Guide
Installing the Quick Configuration Tool
1. Insert the Software CD that came with your NVR into your PC. Navigate to and double-click
Honeywell Config Tool to install the configuration tool software.
The Honeywell Config Tool installation wizard opens.
Figure 2-1 Honeywell Config Tool Wizard
2. Click Next to begin the installation. The User License Agreement page appears.
www.honeywell.com/security
Page 29
Figure 2-2 User License Agreement Page
Configuration | 29
3. Click to select I agree, and then click Install to install the software.
The Installation is Complete page appears has been successful.
Figure 2-3 Installation is Complete Page
4. Click Enjoy Now to open and use the Config Tool.
800-18161 - A - 06/2014
Page 30
30 | Embedded NVR Bundle IP Cameras User Guide
Opening the Honeywell Configuration Tool, Searching for Devices, and Opening a Web Client
In the Config Tool, you will find the IP addresses for the IP devices (NVRs and IP cameras).
1. Click to open the Config Tool.
Figure 2-4 Configtool Interface
2. Click in the Config column for a device to open a Web Client for that device.
Upgrading a Single IP Camera
1. Open the ConfigTool software.
Figure 2-5 ConfigTool Login
2. Select from the list the device you want to upgrade.
3. Click Login to log in to the device.
www.honeywell.com/security
Page 31
Configuration | 31
Note If you do not select a device before clicking Login, you will get a Connection
Error message.
Figure 2-6 Device Upgrade Login Interface
4. Click OK. The Config Upgrade interface appears.
Figure 2-7 Config Upgrade Interface
5. Click OpenFile to select the upgrade file, and then click Upgrade to begin the upgrade.
When the upgrade is complete, and the device is rebooting a Device is offline:
[device IP address] message appears.
800-18161 - A - 06/2014
Page 32
32 | Embedded NVR Bundle IP Cameras User Guide
Figure 2-8 Device Offline Message
6. Click OK to close the Device Offline warning message, and to return to the Upgrade
interface.
Figure 2-9 Upgrade Interface
7. Log into the device again.
www.honeywell.com/security
Page 33
Note If you do not select a device before clicking Login, you will get a Connection
Error.
Upgrading the IP Cameras (Batch Upgrade)
1. Open the ConfigTool software if it is not already open.
Figure 2-10 ConfigTool Login
Configuration | 33
2. Click Upgrade to begin the batch upgrading process.
The Upgrade interface appears.
800-18161 - A - 06/2014
Page 34
34 | Embedded NVR Bundle IP Cameras User Guide
Figure 2-11 Upgrade Interface
3. Click Open to find and select the upgrade file.
The Open interface appears.
Figure 2-12 Open Interface
4. Select the upgrade firmware, and then click Open or double-click the file to open it.
www.honeywell.com/security
The Open interface closes and you return to the Upgrade interface.
Page 35
Figure 2-13 Upgrade Interface
Configuration | 35
5. Click to select the devices you want to upgrade. Their row turns blue when selected.
6. Click Upgrade to begin the batch upgrade.
A message appears in the Upgrade State fields for each selected IP camera to show the
batch upgrade progress.
Figure 2-14 Batch Upgrade Progress Message
800-18161 - A - 06/2014
Page 36
36 | Embedded NVR Bundle IP Cameras User Guide
A message appears to show that the batch upgrade procedure is successful.
Figure 2-15 Batch Upgrade Successful Message
Modifying the IP Address
1. Open the ConfigTool software if it is not already open.
Figure 2-16 ConfigTool Login
www.honeywell.com/security
Page 37
2. Select from the list the device you want to modify.
3. Click Login to log in to the device.
Figure 2-17 Selecting Net in the ConfigTool
Configuration | 37
4. Click Net to open the Net tab.
5. Enter the new IP Address, and the corresponding Subnet Mask and Gateway.
6. Click Save to save these new settings.
800-18161 - A - 06/2014
Page 38
38 | Embedded NVR Bundle IP Cameras User Guide
www.honeywell.com/security
Page 39
3
Web Operation 3
This chapter includes:
• Instructions for connecting to your camera over the Internet.
• A description of the main Internet interface, and instructions on how to configure it.
• Instructions about configuring the camera setup.
Network Connection
The Embedded NVR Bundle IP Cameras support Internet access and management through
your PC. Through the Internet, you can do the following:
• Monitor channel preview
• Configure the system
• Configure and monitor alarms
Before You Begin
Ensure that the following conditions are met:
• Ensure that your network camera is properly connected to the network.
• Ensure that the camera IP address and PC IP address are in the same network segment. If
there is a router, set the corresponding gateway and subnet mask.
• Ping to check that the connection works well. Use "ping *** *** *** ***", where
"*** *** *** ***" is the network camera’s IP address.
800-18161 - A - 06/2014
Page 40
40 | Embedded NVR Bundle IP Cameras User Guide
Browser address bar
Main User Interface
1. Open Internet Explorer, enter the camera’s network address in the address bar, and then
click Enter.
For example, if your camera’s IP address is 192.168.1.108, then please enter
http://192.168.1.108 in the IE browser address bar.
Figure 3-1 Logging in through an IE Browser
2. Enter your username (default: admin) and password (default: 1234), then click Login.
www.honeywell.com/security
The login window appears.
Figure 3-2 Login Window
Page 41
Web Operation | 41
Note For security reasons, please modify your password after you log in for the first
time.
If this is your first time to log in, you will see this message:
Figure 3-3 First Time Login Message
3. (If this is your first time logging in.) Click Please click here to download and install the
plug-in.
A File Download-Security Warning popup appears that asks if you would like to run or
save this file.
800-18161 - A - 06/2014
Page 42
42 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-4 File Download Security Warning Popup for the Plug-in
4. Click Run.
An Internet Explorer - Security Warning appears.
Figure 3-5 Internet Explorer - Security Warning
5. Click Run to start this software.
www.honeywell.com/security
Page 43
Figure 3-6 Plug-in Installation Window
6. Click Install. A progress window appears.
Figure 3-7 Plug-in Installation Progress Window
Web Operation | 43
Live Interface
When you log in, the Live interface appears.
When the plug-in installation is complete, the installation page automatically closes. The
web client automatically refreshes, and then you can view video from the camera.
800-18161 - A - 06/2014
Page 44
44 | Embedded NVR Bundle IP Cameras User Guide
1
2
3
4
Figure 3-8 Live View Window Interface
Table 3-1 Live View Window Sections
Section Number Description
1 Video encoder configuration bar
2 System menu
3 Window function option bar
4 Live view window adjustment tool bar
Video Encoder Setup
Use the Video Encoder configuration bar to configure the main stream, sub stream, and
protocols.
www.honeywell.com/security
Page 45
System Menu
Web Operation | 45
Figure 3-9 Video Encoder Setup Bar
Table 3-2 Live View Window Sections
Parameter Function
Main stream In a normal network bandwidth environment, the main stream
can record audio/video files and support a network monitor.
Set the main stream resolution if your camera supports it.
Sub stream If the network bandwidth is not sufficient, you can use the sub
stream to support a network monitor.
Protocol You can select the stream media protocol from the drop-down
list.
There are three options: TCP, UDP, or Multicast.
The System Menu is used for
• Live monitoring. See Live Interface on page 43.
• Camera setup. See Camera Configuration on page 48.
• Alarm setup. See Alarm on page 92.
• Logging out. See Log Out on page 93.
Figure 3-10 System Menu Bar
800-18161 - A - 06/2014
Page 46
46 | Embedded NVR Bundle IP Cameras User Guide
Configuring the Live View Window
Figure 3-11 Live View Window Tool Bar
Table 3-3 Live View Window Tool Bar
SN Tool Function
Digital zoom • When the video is in the original state, click
Snapshot Click to take a snapshot of an important scene.
and hold down the left mouse button
on Live video to zoom in on a specific area.
Right-click the mouse to restore previous
view.
• Click , then use the middle mouse
button to zoom in/out on the live video.
The snapshot is saved to \picture download
(default). Snapshots are saved in JPEG format.
See Path on page 57 for information about
configuring where snapshots are saved.
To change the default save path, go to
Setup>Camera>Video>Path.
Triple snap Click, and the camera snaps at 1 f/s. All images
Record Click to start manual recording. All video is
Help Click to open the Help file.
Video Window Configuration
The video window configuration controls include these icons:
Figure 3-12 Video Window Configuration Controls
Table 3-4 Video Window Configuration Controls
Icon Function
Image Control
Original Size
Full Screen
Width and Height Ratio
are saved to Setup>Camera>Video>Path.
recorded in Setup>Camera>Video>Path.
www.honeywell.com/security
Adjust Fluency
Page 47
Web Operation | 47
Image Control
Click to open the picture setup interface, which opens in the top right corner of the video
interface.
Figure 3-13 Image Adjustment Interface
Table 3-5 Image Adjustment Controls
Parameter Function
Video Setup
Adjust the monitor’s
brightness.
Adjust the monitor’s contrast.
Adjust the monitor’s hue.
Adjust the monitor’s color
saturation.
Restore brightness, contrast,
saturation, and hue values to
defaults.
Note
• All the operations here
apply to the Web end
only.
• Go to Setup>Camera>
Conditions to adjust the
corresponding items.
Original Size
Click to return the video display to the original, actual size. This size depends on the
resolution of the bit stream.
Full Screen
Click to enter the full-screen mode. Double-click the mouse or press Esc on your
keyboard to exit the full screen mode.
800-18161 - A - 06/2014
Page 48
48 | Embedded NVR Bundle IP Cameras User Guide
Width and Height Ratio
Click to restore the video to the original aspect ratio, or to a ratio suitable for the window.
Fluency Adjustment
Click to select a fluency level to suit your situation. The default is Normal, which has
minimum delay. If your connection is slow, you might select Fluent mode. But if you choose
Fluent mode, there might be a decrease in the image quality, and possibly a delay in the video.
Setup
Camera Configuration
Conditions
On the Conditions tab, you can view camera property information. The configurations become
valid immediately after they are saved.
Figure 3-14 Camera Setup Window
www.honeywell.com/security
Page 49
Web Operation | 49
Table 3-6 Camera Configurations
Parameter Function
Profile Select from Normal, Day, Night.
Brightness Adjusts monitor brightness. Choosing a higher value increases the
video brightness. Adjustments to this value affects the brightness of
the video. Select from 0 to 100. The recommended range is between
40 to 60. The default is 50.
Note If this value is too high, then the video can become hazy.
Contrast Adjusts monitor contrast. Choosing a higher value increases the
contrast. Select from 0 to 100. The recommended range is between 40
to 60. The default is 50.
Note If this value is too low, then the video can become hazy.
Note If this value is too high, then the dark parts of the video could
lose details, and the bright parts of the video could become
overexposed.
Saturation Adjusts monitor color saturation. Choosing a higher value increases
the color saturation/strength. This value has no effect on the general
brightness of the video. Select from 0 to 100. The recommended range
is between 40 to 60. The default is 50.
Note You might see a distortion in grays if the white balance is off.
Sharpness Adjusts video sharpness. Choosing a higher value increases the
sharpness of the video. Select from 0 to 100. The recommended range
is between 40 to 60. The default is 50.
Note Choosing a higher value can introduce video noise to the
image.
Anti-flicker Outdoor: In Outdoor mode, you can select any exposure mode to
avoid flicker.
50Hz: When the current is 50Hz, the system can automatically adjust
the exposure according to the environment’s brightness to prevent
stripes in the video.
60Hz: When the current is 60Hz, the system can automatically adjust
the exposure according to the environment’s brightness to prevent
stripes in the video.
800-18161 - A - 06/2014
Page 50
50 | Embedded NVR Bundle IP Cameras User Guide
Table 3-6 Camera Configurations
Parameter Function
Auto The video brightness can automatically change
Low Noise • The video whole brightness can
Exposure
Low Motion Blur • The video whole brightness can
according to the changes in the scene’s
lighting. If you set a higher gain max value, then
you will get less noise.
automatically change within the proper
exposure range according to the different
environments. The higher the gain max
value is, the lower the noise.
• For the same environments, the noise of
the low noise mode shall be smaller than
the noise of the auto mode.
automatically change within the proper
exposure range according to the different
environments. The lower the gain max
value is, the weaker the tail.
• For the same environments, the noise of
the Low Motion Blur mode will be smaller
than that of the Auto mode.
Manual Displays manual exposure values.
White Balance Sets the White Balance mode, which affects the general hue of the
video. This function is on by default.
Select from Auto, Sunny, Cloudy, Home, Office, Night, or Disable, to
adjust the video to the best quality.
Auto: Auto white balance is on. The system can adjust the color
temperature to ensure that the video color is correct.
Day: The threshold of the white balance is in sunny mode.
Night: The threshold of the white balance is in night mode.
Customized: You can set the gain for the red/blue channel. The value
ranges from 0 to 100.
Day & Night Sets the camera color and the B/W mode switch. When the
configuration file is set to General, then the default is Auto. When the
configuration file is set to Day, then the default is Color. When the
configuration file is Night, then the default is Black & White.
Color: The camera outputs video in color.
Auto: The camera switches from Color to Black & White according to
the conditions, such as if the scene is generally bright, or if IR
illumination is required.
Black & White: The camera outputs black and white video.
www.honeywell.com/security
Page 51
Web Operation | 51
Table 3-6 Camera Configurations
Parameter Function
BLC Mode OFF Disables the BLC function. The default for BLC
is that it is disabled.
BLC The camera automatically adjusts the exposure
to suit the conditions, so that the darkest area
of the video can be seen.
WDR By lowering the brightness of the brightest
area, and enhancing the brightness of the
darkest area, WDR balances brightness and
darkness in a scene so that both the darkest
area and the lightest area can be seen clearly at
the same time.
This value ranges from 1 to 100.
Note When you switch the camera from
non-WDR to WDR mode, there might be
a few seconds lapse in video.
HLC When the HLC function is enabled, the camera
can lower the brightness of the brightest
section of video, according to the selected HLC
control level. HLC can reduce the amount of
halo and lower the brightness of the entire
video image.
This value ranges from 1 to 100. The default
value is 50 when HLC is turned on.
HLC is enabled only when Anti-flicker is set to
Outdoor, and the Exposure is set to Auto.
Mirror Click to switch the video from left to right.
This function is disabled by default.
Flip No Flip: This function is disabled by default.
Flip 180°: The video resolution needs to be set to 720p or less for the
Flip 180° function to work.
3D Noise
3D noise reduction is enabled by default.
Reduction
3D NR Level This value ranges from 0 to 100. The default is 50 when 3D NR is on.
Full-screen
Test
Click the button on the bottom left of the video window to begin
a full-screen test. Double-click to return to the normal-sized test.
Default Click to return the camera to the default setup.
Cancel Click to cancel the current operation and restore the previously saved
operation.
Save Click to save the currently configured customized settings.
800-18161 - A - 06/2014
Page 52
52 | Embedded NVR Bundle IP Cameras User Guide
Profile Management
Figure 3-15 Profile Management Tab
Profile management has three modes: Normal, Full Time, and Schedule.
• Select Normal to configure the video as normal.
• Select Full Time, and you must select either Day or Night for the video.
• Select Schedule, and you can configure a detained time interval.
Note When you make changes to the video configuration, you will immediately see the
Video Configuration
Video Bit Stream
Figure 3-16 Video Bit Stream Configuration Window
effects of those changes in the video. However, you must click Save to save and
apply these settings.
www.honeywell.com/security
Page 53
Table 3-7 Video Bit Stream Configurations
Parameter Function
Code-Stream Type Select from General stream and Motion stream. You can select different
encoder frame rates for different recording events.
The system supports the Active Control Frame (ACF) function. This allows
you to record in different frame rates.
For example, you can use a high frame rate to record important events, use
a lower frame rate to record scheduled events, and set a different frame rate
for recording motion detection.
Encode Mode Select from three options for Encoder Mode: H.264 (main profile standard),
H.264H (high profile standard), and MJPEG mode.
H.264: Main profile encoding mode.
H.264H: High profile encoding mode.
MJPEG: In this encoding mode, the video needs a larger bit stream to
guarantee the video definition. You can use the maximum bit stream value
in the Recommended Bit to get better video output.
Web Operation | 53
Main Stream
Resolution You can select from multiple resolutions from the drop-down list. The
recommended bit stream value is different for each resolution.
Note You can not set a resolution higher than 720p (not including 720p)
when the Flip function is On.
Frame Rate (FPS) PAL: 1~25f/s; NTSC: 1~30f/s.
The frame rate can vary due to different resolutions.
Bit Rate Type Select either VBR or CBR.
Note You can set the video quality in VBR mode.
Reference Bit
Stream
Displays the Reference Bit Rate value according to the resolution and
frame rate you have selected.
Bit Rate In VBR, the Bit Rate here is the maximum value. In CBR, it is a fixed value.
See the Reference Bit Stream for a recommended value.
I Frame Interval Set the P-frame amount between two I frames. The value ranges from 25 to
150. The default is 50.
The recommended value for Frame Rate is *2.
Watermark This function allows you to verify that the video has not been altered. Select
to enable the Watermark function, and then enter the watermark text. The
default watermark text is DigitalCCTV. The maximum length is 85 digits.
The characters can include only numbers, letters, and an underline.
800-18161 - A - 06/2014
Page 54
54 | Embedded NVR Bundle IP Cameras User Guide
Table 3-7 Video Bit Stream Configurations
Parameter Function
Enable Click the check box to enable the extra stream.
This function is enabled by default.
Code-stream Type General bit stream.
Encoder Mode Select from three options for Encoder Mode: H.264 (main profile standard),
H.264H (high profile standard), and MJPEG mode.
The H.264 and H.264H are both H264 bit stream and H.264 is the main
encoding mode. You need to enable the sub stream function in your camera
and set the resolution as CIF. Then you can use a Smartphone or tablet
computer application to monitor the NVR.
MJPEG: In this encoder mode, the video needs a larger bit stream to
guarantee the video definition. You can use the maximum bit stream value
in the reference bit rate to get better video output.
Resolution There are multiple resolutions to select from the drop-down list. The
recommended bit stream value is different for each resolution.
Sub Stream
Frame Rate PAL: 1~25f/s; NTSC: 1~30f/s.
The frame rate can vary due to different resolutions.
Bit Rate Type Select either VBR or CBR.
Note You can select the video quality in VBR mode. The value ranges from
1 to 6.
Recommended Bit
Rate
Recommended bit rate value according to the resolution and frame rate you
have set.
Bit Rate In CBR, the bit rate here is the maximum value. In dynamic video, the
system needs a lower frame rate or lower video quality to guarantee the
quality.
I Frame Interval Set the P-frame amount between two I frames. The value ranges from 25 to
150. The default is 50.
The recommended value for Frame Rate is *2.
www.honeywell.com/security
Page 55
Web Operation | 55
Snapshot
Figure 3-17 Snapshot Configuration Interface
Table 3-8 Snapshot Configurations
Parameter Function
Shapshot Type Select from either General (schedule) or Event (activation).
Image Size Same as the main stream resolution.
Quality Select from six levels of image quality.
Interval Set the snapshot frequency from 1s to 7s.
Note See Path on page 57 for information about configuring where snapshots are
saved.
Note Snapshots are saved as JPEGs.
800-18161 - A - 06/2014
Page 56
56 | Embedded NVR Bundle IP Cameras User Guide
Video Overlay
Figure 3-18 Video Overlay Configuration Interface
Table 3-9 Video Overlay Configurations
Parameter Function
Privacy Mask Used to mask off areas of the video for privacy.
You can configure up to four (4) privacy mask zones.
Channel Title Enable this function so that the system overlays channel
information in the video window.
Use the mouse to drag the channel title to the desired position.
Time Title Enable this function so that the system overlays the time
information in the video window.
Use the mouse to drag the time to the desired position.
Location Enable this function so that the system overlays the customized
location information in the video window.
Use the mouse to drag the location information to the desired
position.
www.honeywell.com/security
Page 57
Web Operation | 57
Path
Figure 3-19 Storage Path Interface
Set the storage path for snapshots ( in the live interface) and for recorded video ( in
the live interface). The default paths are C:\PictureDownload\ and C:\PictureRecord\.
Note Shapshots are saved as bitmaps.
Click Save to save any changes to the storage paths.
800-18161 - A - 06/2014
Page 58
58 | Embedded NVR Bundle IP Cameras User Guide
Network Configuration
TCP/IP
Figure 3-20 TCP/IP Interface
Table 3-10 TCI/IP Configuration
Parameter Function
Host Name Configure to set the current host camera’s name. Maximum 32
characters.
Ethernet Card Select an Ethernet port. The default is wire LAN.
Note If you modify these settings, you will have to reboot your
camera to activate the new setup.
Mode There are two modes: Static and DHCP.
The IP/submask/gateway are Null when you select DHCP mode to
automatically search for the IP.
If you select Static mode, then you need to manually set the
IP/submask/gateway.
If you select DHCP mode, then you can view the
IP/submask/gateway from the DHCP.
If you switch from DHCP mode to Static mode, then you need to
reset the IP parameters.
IP/submask/gateway and DHCP are read-only when the PPPoE
function is correctly working.
MAC Address Displays the MAC address.
IP Version Select the IP version, either IPV4 or IPV6. You can access the IP
address of both of these versions.
www.honeywell.com/security
Page 59
Web Operation | 59
Table 3-10 TCI/IP Configuration
Parameter Function
IP Address Use the keyboard to enter the corresponding number to modify the
IP Address, and then set the corresponding Subnet Mask and
Default Gateway.
Preferred DNS
Server
Alternate DNS
Server
Enable ARP/Ping
to set IP Address
Service
Enter the preferred DNS IP address.
Enter an alternate DNS IP address.
If you know the camera’s MAC address, then use the ARP/Ping
command to modify or set the camera’s IP address.
Before operating the camera, please ensure that the network
camera and the PC are in the same LAN. This function is On by
default.
To enable ARP/Ping to set the IP address service:
1. Get an IP address. Set the network camera and the PC in the
same LAN.
2. Get the physical address from the label on the network camera.
3. Go to the Run interface, and then enter the following
commands:
arp -s <IP Address> <MAC>
ping -l 480 -t <IP Address>
Such as: arp -s 192.168.0.125 11-40-8c-18-10-11
ping -l 480 -t 192.168.0.125
4. Reboot the camera.
You can see that the setup was successful if you can see that
there is output information such as Reply from
192.168.0.125... from the command output lines.
5. Close the command line.
6. Open the browser and then enter http://<IP address>.
Click Enter, and then you should have access.
800-18161 - A - 06/2014
Page 60
60 | Embedded NVR Bundle IP Cameras User Guide
Connection
Figure 3-21 Connection Configuration Interface
Table 3-11 Connection Configurations
Parameter Function
Max Connection This shows the maximum number of Web connections for the same
camera. The value ranges from 1 to 20. The maximum number of
connections is 20.
TCP Port The default is 37777. You can enter an actual port number, if
necessary.
UDP Port The default is 37778. You can enter an actual port number, if
necessary.
HTTP Port The default is 80. You can enter an actual port number, if
necessary.
www.honeywell.com/security
Page 61
Web Operation | 61
Table 3-11 Connection Configurations
Parameter Function
RTSP Port The default is 554. The RTSP stream query format is:
Main stream:
rtsp://username:password@ip:port/cam/realmonitor?
channel=1&subtype=0
Sub stream:
rtsp://username:password@ip:port/cam/realmonitor?
channel=1&subtype=1
You are required to manually enter the following four items:
username/password/IP, and port.
IP: The camera’s IP.
Port: The default is 554. You can leave this field blank if you are
using the default value.
Follow standard RTP protocols, and when the encoding mode is
MJPEG, the maximum resolution only supports 2040x2040.
HTTPs Enable the HTTPs port.
HTTPs Port The default is 443.
PPPoE
Figure 3-22 PPPoE Configuration Interface
1. Enter the PPPoE Username and Password that you received from the Internet Service
Provider (ISP), and enable the PPPoE function.
2. Click to Save the current setup, and then reboot the camera to activate this new setup.
The camera connects to the internet via PPPoE after rebooting.
3. Find the IP address in the WAN from the IP address column.
800-18161 - A - 06/2014
Page 62
62 | Embedded NVR Bundle IP Cameras User Guide
Note When PPPoE is on, please disable UPnP so it does not interfere with PPPoE.
Note You must go to the IP address to check the camera’s current information. You
can access the web client through this address.
DDNS
Set the DDNS to connect the Honeywell DDNS server so that you can access the system
through the servers.
Manually Configuring the DDNS
Figure 3-23 DDNS Configuration Interface
To set the DDNS, go to the corresponding service website to apply a domain name, and then
access the system through that domain. This works even if your IP address has changed.
Note When your camera is connected to the WLAN, you should disable UPnP.
www.honeywell.com/security
Page 63
Web Operation | 63
Table 3-12 DDNS Configurations
Parameter Function
Server Type You can select the DDNS protocol from the drop-down list, and then
enable the DDNS function. Select the Honeywell DDNS server (which is
free) to enable the DDNS function.
Server Address The DDNS server IP address.
Domain Name Your self-defined domain name.
Username The user name you enter to log into the server.
Password The password you enter to log into the server.
Update Period This is the frequency at which the camera regularly sends out the life
signal to the server.
You can set the interval value between the camera and the DDNS server
here.
Using Honeywell DDNS to Configure DDNS
Figure 3-24 Using Honeywell DDNS to Configure DDNS
Table 3-13 Honeywell DDNS Configurations
Parameter Function
Server Type You can select the DDNS protocol from the drop-down list, and
then enable the DDNS function. Select the Honeywell DDNS server
(which is free) to enable the DDNS function.
Server Address This is the DDNS server IP address. Under Honeywell DDNS, the
default server address is www.hennvr-ddns.com.
Mode Select Auto or Manual. The default is Auto. If you select Manual,
then you must enter a domain name.
Domain Name Auto and self-defined domain names are both MAC
address.hennvr-ddns.com. You can define the prefix.
Username The user name you enter to log in the server (Optional).
800-18161 - A - 06/2014
Page 64
64 | Embedded NVR Bundle IP Cameras User Guide
IP Filter
Enable the IP filter function so that only the specified IP/MAC addresses can access the network
camera. You can specify an IP address or an IP address segment, such as from 192.168.1.1 to
192.168.1.100, for example. If you do not check the box to enable Tru sted Sites, then there will
be no access limitation.
Figure 3-25 IP Filter Configuration Interface
Before you can restrict access through the cameras through the IP filter, you must first configure
the Trusted Sites here.
Note You must add these addresses before enabling Trusted Sites.
Note You must set the MAC address in the same network segment as the camera’s IP
address.
www.honeywell.com/security
Page 65
SMTP (Email)
Figure 3-26 SMTP Configuration Interface
Web Operation | 65
Table 3-14 SMTP (Email) Configurations
Parameter Function
SMTP Server Enter the server address.
Port The default value is 25. You can modify this value as necessary.
Anonymity Supports the anonymity function for the server. You can
automatically login anonymously. You do not need to enter the user
name, password, and the sender information.
Username The username for the sender’s email account.
Password The password for the sender’s email account.
Sender The sender’s email address.
Authentication
Enable
Title Subject: Enter the email subject here.
Attachment If you check this box, then the system can send out an email with
Mail Receiver Enter the receiver’s email address here. You can add a maximum
This is the encryption mode. Select SSL, TLS, or None.
the snapshot picture.
of three addresses.
800-18161 - A - 06/2014
Page 66
66 | Embedded NVR Bundle IP Cameras User Guide
Table 3-14 SMTP (Email) Configurations
Parameter Function
Interval The interval for sending ranges from 0 to 3600 seconds. 0 seconds
means that there is no interval.
The system will not immediately send the email when the alarm
occurs. When an alarm, motion detection, or abnormality occurs to
activate an email, the system sends the email according to the
interval you have specified here. This is very useful when there are
too many emails that have been triggered, which can result in a
heavy load for the email server.
Health Mail Enable Check to enable this function.
Update Period
(interval)
Email Test The system will automatically send an email to test the connection.
This allows the system to send a test email to check the connection.
Check to enable this function, and then set the corresponding email
interval.
You can set the Update Period so that the system sends out
regularly scheduled emails.
Before you can do an email test, you must save the email setup
information.
UPnP
UPnP allows you to establish the mapping relationship between the LAN and the public network.
In the UPnP configuration interface, you can add, modify, or remove a UPnP item.
Figure 3-27 UPnP Configuration Interface
www.honeywell.com/security
Page 67
Web Operation | 67
Note For UPnP on different routers, you must disable the UPnP function.
Enabling UPnP in Windows
If UPnP is enabled in the Windows operating system, then the network can automatically detect
the camera through My Network Places.
1. Go to Start>Control Panel>Add or remove programs.
2. Click to select Add or remove programs, and then select Network Services from the
Windows Components Wizard.
3. Click Details, and then click to select Internet Gateway Device Discovery and Control
client and UPnP User Interface.
4. Click OK to begin the installation.
SNMP
SNMP allows for the communication between the network management work station software
and the proxy for the managed camera. Please install software such as MG MibBrowser 8.0c or
establish SNMP service before you use this function.
Note You must reboot the camera to activate the new setup.
800-18161 - A - 06/2014
Page 68
68 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-28 SNMP Configuration Interface
Table 3-15 SNMP Configurations
Parameter Function
SNMP Port The listening port for the proxy program of the device/camera. This
is a UDP port not a TCP port. The value ranges from 1 to 65535.
The default is 161.
Read Community This is a string, and it is a command between the management
process and the proxy process. The read community defines the
authentication, the access control, and the management
relationship between one proxy and one group of the managers.
Please ensure the camera and the proxy are the same.
The read community will read all the objects that the SNMP
supports in the specified time. The default setting is public.
Write Community This is a string, and it is a command between the manage process
and the proxy process. The write community defines the
authentication, the access control, and the management
relationship between one proxy and one group of the managers.
Please ensure the camera and the proxy are the same.
The write community will read/write/access all the objects that the
SNMP supports in the specified time. The default setting is write.
Trap Address The destination address of the Trap information from the camera’s
proxy program.
Trap Port The destination port of the Trap information from the camera’s
proxy program. This is for exchanging information between the
gateway camera and the client-end PC in the LAN. It is a
non-protocol connection port. It has no effect on the network
applications. It is a UDP port not a TCP port. The value ranges from
1 to 65535. The default is 162.
www.honeywell.com/security
Page 69
Web Operation | 69
Table 3-15 SNMP Configurations
Parameter Function
SNMP Version SNMP v1: The system only processes v1 information.
SNMP v2: The system only processes v2 information.
SNMP v3: You can set the user name and password. There is
account security verification when the server wants to connect to
the camera. At the same time, the v1 and v2 is null and cannot be
selected.
Read-only
Username
Authentication
Type
Authentication
Password
Encryption Type You can configure this parameter only when you select SNMP v3.
Encryption
Password
Read&write
Username
Authentication
Type
Authentication
Password
Encryption Type You can configure this parameter only when you select SNMP v3.
Encryption
Password
You can configure this parameter only when you select SNMP v3.
The default setting is public.
You can configure this parameter only when you select SNMP v3.
You can select either MD5 or SHA. The default setting is MD5.
You can configure this parameter only when you select SNMP v3.
The password requires a minimum of 8 characters.
The default setting is CBC-DES.
You can configure this parameter only when you select SNMP v3.
The password requires a minimum of 8 characters.
You can configure this parameter only when you select SNMP v3.
The default setting is private.
You can configure this parameter only when you select SNMP v3.
You can select either MD5 or SHA. The default setting is MD5.
You can configure this parameter only when you select SNMP v3.
The password requires a minimum of 8 characters.
The default setting is CBC-DES.
You can configure this parameter only when you select SNMP v3.
The password requires a minimum of 8 characters.
Bonjour
Bonjour is based on the multicast DNS service from Apple. It can automatically broadcast its
service information and listen to the camera information from the other camera.
800-18161 - A - 06/2014
Page 70
70 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-29 Bonjour Configuration Interface
If you do not know the network camera’s information such as its IP address, you can use
Bonjour’s browser in the same LAN to search for and then access network cameras.
After the network camera is detected by Bonjour, you can see the server name.
Note You can also use Bonjour with the Safari browser.
1. Click Display All Bookmarks in your browser.
2. Open Bonjour.
The system should automatically detect network cameras through Bonjour on the LAN.
Multicast
Multicast is a transmission mode for data packets. When there are multiple hosts to receive the
same data packet, multiple cast (multi-cast) is the best option for reducing the bandwidth and
the CPU load. The source host can send out just one data packet. This function depends on the
relationship between group members and the router’s group.
In the Multicast configuration interface, you can set the multicast address and port.
Note You also need to go to the Live interface to set the protocol to Multicast.
www.honeywell.com/security
Page 71
Figure 3-30 Mulitcast Configuration Interface
Table 3-16 Multicast Configurations
Web Operation | 71
Parameter Function
Enable Select to enable the multicast function. Main stream and sub stream
can not be used at the same time.
Multicast Address The main/sub stream multicast address is 239.255.42.42 and its
range is 224.0.0.0~239.255.255.255.
Port Multicast port. The main stream is 36666; the sub stream is 36667,
and the range is 1025~65534.
IEEE802.1X
IEEE802.1X is the access control and authentication protocol for local and metropolitan area
networks. It uses a port-based network access control protocol to restrict unauthorized user
and/or device access to the LAN / WLAN.
IEEE802.1X supports the client’s ability to manually choose how authentication works for
accessing the LAN or not. IEEE802.1X supports the ability to:
• authenticate
• calculate the fee
•ensure security
• maintain requirements
800-18161 - A - 06/2014
Page 72
72 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-31 802.1X Configuration Interface
Table 3-17 802.1X Configurations
Parameter Function
Authentication PEAP (protected EAP protocol)
Username Enter a username to log in. This username is authenticated by the
server.
Password Enter the password.
QoS
Quality of Service (QoS) is a network security mechanism. It fixes problems with network delay
and jams. For network service, the quality of service includes the transmission bandwidth, delay,
and packet loss, for example. Through QoS, we can guarantee the transmission bandwidth, to
reduce the delay, to reduce the loss of data packets, and to enhance the quality with anti dither.
You can set the IP’s DSCP (Differentiated Services Code Point) to distinguish the data packet
so that the router or the hub can provide different services for various data packets. It can select
different queues according to the priority of the packets, and select the bandwidth for each
queue. It can also select different ratios to discard if the bandwidth is overloaded.
www.honeywell.com/security
Page 73
Figure 3-32 QoS Configuration Interface
Table 3-18 QoS Configurations
Web Operation | 73
Parameter Function
Realtime Monitor This value ranges from 0 to 63. The router or the switcher can
provide different service for different packets.
Command This value ranges from 0 to 63. The router or the switcher can
provide different service for different packets.
800-18161 - A - 06/2014
Page 74
74 | Embedded NVR Bundle IP Cameras User Guide
Events
Video Motion Detection
Figure 3-33 Motion Detection - Video Detection Configuration Interface
Table 3-19 Video Motion Detection - Video Detection Configurations
Parameter Function
Enable Check to enable motion detection.
Working Period Configure the arm/disarm period. Click Setup to open the setup
menu. See Configuring the Working Period on page 75.
Anti Dither The system memorizes only one event during the anti-dither
period. Choose an anti-dither period from 0s to 100s.
Area Configure the motion detection region, its sensitivity, and area. The
default settings covers the entire area. You must click Save to
enable these settings. See Configuring the Motion Detection Area
on page 76.
Record When Record is enabled, you can trigger motion detection to
activate recording.
Record Delay The system can delay recording for a specified time after the alarm
has ended. Choose a delay period from 10s to 300s.
Send Email When this function is enabled, the system sends an email alert to
you when an alarm occurs.
Snapshot Check to enable the system to backup motion detection snapshot
files. (See Path on page 57 for information about configuring where
snapshots are saved.)
www.honeywell.com/security
Page 75
Configuring the Working Period
Figure 3-34 Configuring the Working Period
Web Operation | 75
800-18161 - A - 06/2014
Page 76
76 | Embedded NVR Bundle IP Cameras User Guide
Configuring the Motion Detection Area
Figure 3-35 Configuring the Motion Detection Area
Table 3-20 Motion Detection Area Configurations
Parameter Function
Sensitivity Adjust the brightness sensitivity. You might need to increase the
brightness sensitivity to trigger motion detection. You can
configure up to four areas. The sensitivity ranges from 0 to 100. We
recommend that you choose a sensitivity between 30 to 70. The
default is 50.
Threshold The threshold determines how much change in a scene is required
to trigger an alarm. The lower the threshold setting, the easier it is
to trigger a motion detection alarm. You can configure up to four
areas. The sensitivity ranges from 0 to 100. We recommend that
you choose a sensitivity between 10 to 50.
Delete All Delete all motion detection areas.
Delete Delete the selected motion detection area.
www.honeywell.com/security
Page 77
Tampering
Figure 3-36 Tampering Configuration Interface
Table 3-21 Tampering Configurations
Parameter Function
Web Operation | 77
Enable Check to enable the Tampering function.
Working Period The video masking feature is activated during the specified period.
See Tampering Working Period Configuration Interface on page 78.
You can configure up to six periods per day. Draw a circle to enable
the corresponding time period.
Select a date. If you do not select a date, the current setup will be
applied to today only. You can select All to apply the working
period to the whole week.
Click OK to save the changes. The system goes back to the Motion
Detection interface. Click Save to exit.
Record If Record is enabled, a video masking event can activate recording.
Record Delay The system will wait for the specified time before it begins
recording. Select from 10s to 300s.
Send Email When enabled, the system sends an email alert when an alarm
occurs.
Snapshot When enabled, the system automatically sends an email when an
alarm occurs.
800-18161 - A - 06/2014
Page 78
78 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-37 Tampering Working Period Configuration Interface
Abnormality
There are two statuses: Disconnection and IP Conflict.
Figure 3-38 Disconnection Configuration Interface
Figure 3-39 IP Conflict Configuration Interface
www.honeywell.com/security
Page 79
Storage
Web Operation | 79
Recording Schedule and Snapshot Schedule
You can add or remove schedules for recording and snapshots.
There are two recording modes: General (auto) and Motion Detection.
You can configure up to six recording periods per day.
Note Ensure that you have enabled the corresponding recording mode in
Setup>Storage>Conditions.
Figure 3-40 Recording Schedule Configuration Interface
Recording Schedule Color Codes:
• Green: General recording/snapshot
• Yellow: Motion detection recording/snapshot
Setting Holidays
You can set specific days as holidays, for which the recording schedule is different. When
enabled, the selected/configured dates will record according to the holiday setup.
800-18161 - A - 06/2014
Page 80
80 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-41 Holiday Schedule
Destination
Configure the storage mode for the network camera recording files or snapshots. Choose from:
Local or FTP. You can select only one mode at a time. The system can save according to the
event type. The event type corresponds with the two modes (general/motion) in the Schedule
interface. Check the box to enable.
Figure 3-42 Destination Configuration Interface
Table 3-22 Destination Configurations
Parameter Function
Event Type Including Scheduled and Motion Detect.
FTP Select to save in the FTP server.
Click FTP to open the FTP tab.
www.honeywell.com/security
Page 81
Web Operation | 81
Figure 3-43 FTP Configuration Interface
Check to enable FTP. When enabled, event-triggered (either scheduled or motion detection,
depending on what you chose in Figure 3-42) video and snapshots will be saved to the FTP.
Record Control
Figure 3-44 Record Control Configuration Interface
Table 3-23 Record Control Configurations
Parameter Function
Pack Duration Select the file size. The default is 8 minutes.
Pre-event Record Enter a pre-record value.
For example, the system can record the four seconds of video in the
buffer. Recording begins five seconds before the event trigger.
Disk Full Choose from: Stop Recording or Overwrite the previous files
when the HDD is full.
Overwrite: If the current working HDD is full, then the system will
overwrite the previous file.
Stop: If the current working HDD is full or is overwriting, the system
will stop recording.
Record Mode Choose from: Auto, Manual, or Off.
Record Stream Choose from: Main Stream or Sub Stream.
800-18161 - A - 06/2014
Page 82
82 | Embedded NVR Bundle IP Cameras User Guide
System
General System Setup
The general interface includes the local host setup (including the camera name and GUI
language), and the date/time setup.
General
Figure 3-45 General System Configuration Interface
Table 3-24 General System Configurations
Parameter Function
Device Name Enter the camera’s name.
Language Select a language from the drop-down list.
Video Standard Select the video standard, either NTSC or PAL.
www.honeywell.com/security
Page 83
Date and Time
Figure 3-46 Date and Time Configuration Interface
Web Operation | 83
Table 3-25 Date and Time Configurations
Parameter Function
Date Format Select a date format from the drop-down list.
Time Format Select a time format, either 24-hour or 12-hour.
Time Zone Select the time zone for the camera.
Current Time Set it to set the system’s time. You have to Save to activate this
time.
Sync PC Click to sync the camera’s time with your PC’s time.
DST Configure the Daylight Savings Time for the camera, when Daylight
Savings Time begins and ends. Choose from either a Date or a
Week for the DST.
NTP Click to enable NTP.
NTP Server Configure the NTP time server.
Port Configure the port for the NTP time server.
Update Period Configure synchronization periods between the camera and the
time server.
800-18161 - A - 06/2014
Page 84
84 | Embedded NVR Bundle IP Cameras User Guide
Accounts
Note The system supports up to 15 characters for the user name or user
group name. You can use letters, numbers, and the underline (_) for the
user or group name.
You can configure up to 18 users and eight groups (default factory settings). The
factory default setup includes two user levels: user and admin.
When configuring groups, you can configure the rights of those groups.
You can also set rights for individuals within groups.
Note User management adopts group/user modes. The user name and the group
name should be unique. A user can be included in only one group at a time.
User Name
In the Username Configuration interface, you can enable anonymous login, add/remove
users, and modify a username.
Figure 3-47 Username Configuration Interface
Enable Anonymous Login: Click to enable. When you enter an IP, no username or password
is required. You can log in anonymously (with limited rights). Click Logout to end your
anonymous session.
Add User: Add a user to a group and configure that user’s rights.
www.honeywell.com/security
Page 85
Figure 3-48 Add User Configuration Interface
Web Operation | 85
There are four types of default user:
•admin
• 888888
• 666666
• hidden user "default"
All user types except 666666 have administrator rights. 666666-type users have only monitoring
rights.
The hidden user "default" is for internal system use only, and it can not be deleted. When there
is no login user, this hidden user "default" is automatically used for logging in. You can configure
some rights for the hidden user, such as monitoring ability, so that user can view channels
without logging in.
In the Add User configuration interface, you can enter a user name and password, then select
a group.
Note User rights can not exceed the rights of the group to which that user belongs.
TIP! Ensure that the general user has lower rights than the admin user.
Modifying Users: Click to modify a user’s properties, including their group, passwords,
and rights.
800-18161 - A - 06/2014
Page 86
86 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-49 Modifying User Interface
Modifying a Password: Enter the old password once, and then enter the new password twice
to confirm the new password. Click Save to save the new settings.
Note Passwords can contain up to 32 characters, using numbers and letters only.
Only users with account rights can modify other users’ passwords.
Group
In the Group configuration interface, you can add/remove groups and modify group passwords.
www.honeywell.com/security
Page 87
Figure 3-50 Group Configuration Interface
Web Operation | 87
Adding a Group: Add a group and configure that group’s rights. Enter the group name, and
then check the box to select the corresponding rights, including live (view), record control, and
account.
Figure 3-51 Add Group Interface
Modifying a Group: Click Modify Group to open the Modify Group interface.
800-18161 - A - 06/2014
Page 88
88 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-52 Modify Group Interface
Default
In the Modify Group Interface, you can edit Remarks and Rights.
Click Default to restore the camera to the factory preset settings.
Figure 3-53 Default Interface
Note The system can not reset some information, such as the network IP address.
www.honeywell.com/security
Page 89
Import/Export
Web Operation | 89
Figure 3-54 Import/Export Configuration Interface
Table 3-26 Import/Export Configurations
Parameter Function
Import Click to import local setup files to the system.
Export Click to export the corresponding system setup to your local PC.
Automatic Maintenance
You can select either Auto Reboot or Manual Reboot.
Figure 3-55 Auto Maintain Configuration Interface
800-18161 - A - 06/2014
Page 90
90 | Embedded NVR Bundle IP Cameras User Guide
Upgrade
Figure 3-56 Upgrade Interface
Select the upgrade file, and then click Upgrade to begin the firmware update.
CAUTION Selecting the incorrect upgrade file might cause a
camera malfunction.
Information
Version
In the Version interface, you can view the system hardware features, the software version, and
the release date. This information is for reference only; it is not configurable.
Figure 3-57 Version Interface
www.honeywell.com/security
Page 91
Log
Figure 3-58 Log Interface
Web Operation | 91
Table 3-27 Log Interface Configurations
Parameter Function
Start Time Configure the start time for the requested log.
End Time Configure the end time for the requested log.
Type Select a log type: System, Operation, Configuration Operation,
Data Operation, Event Operation, Record Operation, Account
Management, Log Clearing.
Search Select a log type from the drop-down list, and then click Search to
view the list that is generated by the search.
Click Stop to terminate the current search.
Log Information Select one item to view its detailed information.
Backup Click Backup to back up log files to the currently selected PC.
Clear Click Clear to delete all the displayed log files.
Note The system does not support clearing by type.
Online User
View the current online user, group name, IP address, and log-in time.
800-18161 - A - 06/2014
Page 92
92 | Embedded NVR Bundle IP Cameras User Guide
Figure 3-59 Online User Interface
Alarm
Click the Alarm tab to open the alarm configuration interface.
Figure 3-60 Alarm Configuration Interface
Table 3-28 Alarm Configurations
Type Parameter Function
Motion Detection System alarms when a motion detection alarm
Alarm Type
occurs.
www.honeywell.com/security
Tampering System alarms when the camera has been
tampered with.
Page 93
Log Out
Web Operation | 93
Table 3-28 Alarm Configurations
Type Parameter Function
Operation Prompt System pops up an alarm dialog box.
Play Alarm Tone When an alarm occurs, the system automatically
Alarm Tone
Tone Path Select the alarm sound file.
Click Log Out to log out of the system. The system automatically opens the Log In interface.
Figure 3-61 Log In Interface
generates an audible sound. You can select a
tone from your PC for the alarm tone prompt.
800-18161 - A - 06/2014
Page 94
94 | Embedded NVR Bundle IP Cameras User Guide
www.honeywell.com/security
Page 95
A
Troubleshooting A
Table A-1 Troubleshooting
Problem Possible Cause/Solution
I can not boot up
the camera or
operate it properly
Water leakage
occurred
IR video is poor Check the power supply. The improper power supply might not be
I can not upgrade
the camera
through the
network
I can not login to
the client-end or
the WEB
Click and hold RESET for at least five seconds to restore the
camera’s factory default settings.
Check the front glass cap or rear waterproof cap. Removing or
loosening the front or rear cap could result in water leakage.
able to support the IR lights.
The object that you want illuminated might be out of the IR
illumination range.
IR-CUT does not switch to Night mode. The photosensitive chip at
the front end of the camera might be malfunctioning.
If the network upgrade fails, try using port 3800 to continue the
upgrade.
Windows OS 98/Windows ME: If you can not install the client-end or
can not view video after installation, we recommend that you switch
to Win 2000 SP4 OS or install a lower version of the client-end
software.
Ensure that the ActiveX controls are not blocking the client-end.
Ensure that your video cards is dx8.1 or higher.
Ensure that you have a good network connection.
Ensure that you have a valid network setup. See Network
Configuration on page 58.
Ensure that you are using a valid username and/or password.
800-18161 - A - 06/2014
Page 96
96 | Embedded NVR Bundle IP Cameras User Guide
Table A-1 Troubleshooting
Problem Possible Cause/Solution
I can not play the
downloaded file
Ensure that you have a player. Look for the player on the CD that
came with your camera.
Ensure that your video card is dx8.1 or higher.
Media Player: Ensure that you have installed the Div
X503Bundle.exe plugin for playing .AVI files.
Windows XP: Ensure that you have installed the Div
X503Bundle.exe plugin for playing .AVI files and the ffdsho-2004
1012.exe plugin.
To guarantee
setup update
After you have modified the setup, please reboot the camera
through the software, to ensure that the updates are applied.
Power adapter The general power adapter can work ranging from 0°C to 40°C. The
camera might experience an unstable power supply when the
temperature exceeds the working temperature.
Please replace with an industry-level power adapter if you are using
in cold-weather environments. We recommend that you use a UPS
power adapter.
www.honeywell.com/security
Page 97
B
Specifications B
Table B-1 Specifications
Operational
Video Standard NTSC / PAL
Scanning System Progressive
Image Sensor 1/3" 2 Megapixel progressive scan Exmor CMOS
Effective Pixels 1920 (H) × 1080 (V)
Minimum Illumination 0.5 Lux @ F1.6 (Color); 0 Lux @ F1.6 (IR LEDs on)
Maximum IR LEDs
length
Video Output N/A
S/N Ratio More than 50 db
Gain Control Auto / Manual
Electronic Shutter
Speed
Lens Type 3.6 mm Fixed, F1.6
Horizontal Angle of
View
Mount Type Board-in type
White Balance Auto / Day / Night / Customized
Day/Night Auto(ICR) / Color / B&W
Backlight
Compensation
H2D2PR1: 20 m
HBD2PR1: 30 m
Auto / Manual (1/3 ~ 1/10000s)
H2D2PR1: 88° (53°)
HBD2PR1: 88° (53°/39°)
BLC/DWDR
Exposure Mode Manual / Low noise / Low motion blur / Auto
Ranges from 1/3 to 1/10000
Video Frame Rate PAL: Main Stream (1920 x 1080 @ 25fps),
Sub Stream (704 x 576 @ 25fps)
NTSC: Main Stream (1920 x 1080 @ 30fps),
Sub Stream (704 x 480 @ 30fps)
800-18161 - A - 06/2014
Page 98
98 | Embedded NVR Bundle IP Cameras User Guide
Table B-1 Specifications
Noise Reduction 3D
Video Flip Support mirror function and flip function.
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports 4 privacy mask zones (max).
Video Setup Support parameter setup such as bright, contrast.
Video Information Channel title, time title, motion detect, privacy mask.
Motion Detection 396 (18 x 22) detection zones; sensitivity level ranges from 0 to
Electrical
Power Supply 12 V DC
Power Consumption 6 W maximum
100; area threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email
function and etc.
PoE IEEE802.3af, Type X, Class X
Mechanical
Dimensions H2D2PR1: Ø4.5 x 3.4 inches (Ø114 x 86 mm)
HBD2PR1: 6.6 x 2.6 x 2.3 inches (168.1 x 66.0 x 58.4 mm)
Weight H2D2PR1: 0.64 pounds (0.29 kg)
HBD2PR1: 1.10 pounds (0.5 kg)
Construction
Recording and Storage Network storage
Connectors 1-channel wire Ethernet port; 10/100 Base-T Ethernet
Environmental
Operational
-4°F to +140°C (-20°C to +60°C)
Temperature
Working Humidity less than or equal to 95%
Rating IP66
IP Specifications
Video Compression H.264 / MJPEG
Primary Stream
Resolution
1080p (1920 x 1080) / SXGA (1280 x 1024) / 1.3M (1280 x 960)
/ 720p (1280 x 720) / D1(704 x 576; 704 x 480) / CIF (352 x 288;
352 x 240)
Frame Rate Main Stream: 1080p / SXGA / 1.3M / 720p / D1 / CIF (1~25/30
fps)
Sub Stream: D1 / CIF (1~25/30 fps)
www.honeywell.com/security
Video Streaming Dual Streaming: H.264/MJPEG; MJPEG
Video Bit Rate H.264: 1280 K~8192 Kbps @ 1080p
Page 99
Specifications | 99
Table B-1 Specifications
Security Up to 20 users, multiple user access levels with password
protection
Operating System
CPU Requirements
System Memory
Network Card RJ-45 (10/100 Base-T)
®
Web Browser Microsoft Internet Explorer
Google Chrome®; Apple Safari
6.0 or later; Mozilla Firefox®;
®
Network Protocol IPv4 / IPv6, HTTP, HTTPS, SSL, TCP/IP, UDP, UPnP, ICMP,
IGMP, SNMP, RTSP, RTP, SMTP, NTP, DHCP, DNS,
Smart Phone/Tablet
IOS; Android
Compatibility
Standards ONVIF Profile S
Network
Default Restoration Built-in RESET button
Remote Operation Monitor; system setup; log information; maintenance upgrades.
Regulatory
Emissions FCC Part 15B, CE (EN 55022)
Immunity EN 50130-4
Safety EN 60950-1
North America UL listed to UL/CSA 60950-1
800-18161 - A - 06/2014
Page 100
100 | Embedded NVR Bundle IP Cameras User Guide
www.honeywell.com/security
Loading...