Honeywell ES800 User Manual

Safety of household and similar electrical appliances

Part 2-98: Particular requirements for humidifiers

Report Number. .............................. :

Test Report issued under the responsibility of:

TEST REPORT
IEC 60335-2-98

160421073GZU-003

Date of issue ................................... :

Total number of pages ................... :

July 05, 2016; Modification 1: October 12, 2016
116

Applicant’s name ............................ :

Address ........................................... :

Jmatek Limited
Suite 808A, Tower A, Manulife Financial Centre, 223-231 Wai Yip

Street, Kwun Tong, Hong Kong.

Test specification:

Standard .......................................... :

IEC 60335-2-98:2002 (Second Edition) + A1:2004 + A2:2008
IEC 60335-1:2010 (Fifth Edition)

Test procedure ............................... :

Non-standard test method ............. :

Test Report Form No. ..................... :

Test Report Form(s) Originator..... :

Master TRF ...................................... :

LVD
N/A
IEC60335_2_98E
VDE
Dated 2013-06

Copyright © 2013 Worldwide System for Conformity Testing and Certification of Electrotechnical
Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved.

This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.

If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.

This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.

Test item description ..................... :

Trade Mark ...................................... :

Manufacturer ................................... :

Model/Type reference .................... :

Ratings ............................................ :

Humidifier (Evaporative Air Cooler)
Honeywell
Jmatek Limited
ES800, ES071-1AE
DC24V, 36W, 1,5A, Class III

Note: this appliance can be powered by adapter mode with rating:
Input: AC 100-240V, 50/60Hz, 1,5A or 1,0A, Output: 24V, 1,5A,
Class II.

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 3 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

List of Attachments (including a total number of pages in each attachment): N/A
N/A

Summary of testing:

The products tested comply with the standards of
EN 60335-1:2012+A11:2014
EN 60335-2-98:2003+A1:2005+A2:2008
EN 60335-2-80:2003+A1:2004+A2:2009
EN 62233:2008

Tests performed (name of test and test clause):
Original:

Testing location:

Intertek Testing Services Shenzhen Ltd.
Guangzhou Branch

Full tests were conducted on model ES071-1AE.
Tests of clause 10, 11, 13, 15, 20, 29, 30 and

construction check were conducted on ES800.

Block E, No.7-2 Guang Dong Software Science
Park, Caipin Road, Guangzhou Science City,
GETDD, Guangzhou, China

Modification 1:

After reviewed, no test was needed to be conducted
on the appliance.

Summary of compliance with National Differences
List of countries addressed: EUROPEAN GROUP DIFFERENCES

The product fulfils the requirements of EN 60335-1:2012+A11:2014; EN 60335-2-

98:2003+A1:2005+A2:2008; EN 60335-2-80:2003+A1:2004+A2:2009; EN 62233:2008.

Copy of marking plate:
The artwork below may be only a draft. The use of certification marks on a product must be

authorized by the respective NCBs that own these marks.

Remark: the label of model ES071-1AE is the same as above except the model name.
Note1: When placing these electrical equipments on the market, the importer and manufacturer will

indicate on the electrical equipments his name, registered trade name or registered trade mark and the
postal address at which he can be contacted.

Note2: When placing these electric equipement on the market, Type, batch, or series number that allows
their identifications will be marked.

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 4 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

Test item particulars .................................................. :

Classification of installation and use ...................... :

Supply Connection..................................................... :

...................................................................................... :

Possible test case verdicts:

- test case does not apply to the test object ............ :

- test object does meet the requirement .................. :

- test object does not meet the requirement ............ :

Testing .......................................................................... :

Date of receipt of test item ......................................... :

Date (s) of performance of tests ................................ :

Portable appliance, Class III
Safety extra low voltage

N/A
P (Pass)
F (Fail)

September 29, 2016
September 29, 2016 – October 12, 2016

General remarks:

The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.

Throughout this report a comma / point is used as the decimal separator.

When determining the test result, measurement uncertainty has been considered.
This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between

Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the
agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the
agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is
authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek
name or one of its marks for the sale or advertisement of the tested material, product or service must first
be approved in writing by Intertek. The observations and test results in this report are relevant only to the
sample tested. This report by itself does not imply that the material, product, or service is or has ever been
under an Intertek certification program.

The test report only allows to be revised only within the report defined retention period unless standard or
regulation was withdrawn or invalid.

Manufacturer’s Declaration per sub-clause 4.2.5 of IECEE 02:

The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the

Yes
Not applicable

sample(s) submitted for evaluation is (are)
representative of the products from each factory has

been provided ................................................................ :

When differences exist; they shall be identified in the General product information section.

Name and address of factory (ies) ........................... :

Foshan Shunde Toppin Electrical Technology Co.,
Ltd
No.7 Chaogui Road Hi-Tech Area,Ronggui, Shunde

District, Foshan City, Guangdong, China

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 5 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

General product information:
Original:

The appliances are evaporative air cooler intended for household indoor use.
The appliances are supplied by a safety extra-low voltage.
The two models have the same electric component, such as DC fan motor, water pump, sync. Motor and
etc.

Modification 1:

This test report replaces the original test report 160421073GZU-003, dated on July 05, 2016. It is issued
because of adding supplementary information in this report:

1. Add “Note: this appliance can be powered by adapter mode with rating: Input: AC 100-240V,

50/60Hz, 1,5A, Output: 24V, 1,5A or 1,0A, Class II.” in Ratings on page 1.

2. Add below information in table 24.1:

Note: this appliance can be powered by the following adapter mode
Adapter Foshan city

Dizhi power
supply Co., Ltd.

DSS36­2401500-H

Input: AC 100­240V; 50/60Hz;
1,5A; Output:

IEC/EN 61558­2-16

TUV Rheinland
S 50316491

24V; 1,5A;
Class II

Alternative Dongguan yuan

shuai electronic
Co., Ltd

YeS36W­2400150V

Input :100­240V~; 50/60H
z; 1,0A Max;
Output : 24V;
1,5A; Class II

Alternative Various Various Input: AC 100-

240V; 50/60Hz;
1,5A; Output:
24V; 1,5A;
Class II

IEC/EN 61558­2-16

IEC/EN 61558­2-16

Intertek
16HKS0430-01

S & other EU
certification
marks

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 6 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

5 GENERAL CONDITIONS FOR THE TESTS ---­ Tests performed according to clause 5, e.g. nature

P

of supply, sequence of testing, etc.

5.6 Humidistats are short-circuited or rendered

N/A

inoperative (IEC 60335-2-98)

6 CLASSIFICATION ----

6.1 Protection against electric shock:

Class III P

Class 0, 0I, I, II, III ....................................... ......... :

6.2 Protection against harmful ingress of water IPX0 N/A

7 MARKING AND INSTRUCTIONS ----

7.1 Rated voltage or voltage range (V) ....................... : DC24V P

Symbol for nature of supply, or ............................. :

P

Rated frequency (Hz) ............................................ : N/A

Rated power input (W), or ..................................... : 36 P

Electrode-type appliances marked with rated power

N/A

input (IEC 60335-2-98)

Rated current (A) ................................................. : 1,5 P

Manufacturer's or responsible vendor's name,

Honeywell P

trademark or identification mark ........................... :

Model or type reference ........................................ : See marking plates P

Symbol IEC 60417-5172, for class II appliances N/A

IP number, other than IPX0 .................................. : IPX0 N/A

Symbol IEC 60417-5180, for class III appliances,

P

unless
the appliance is operated by batteries only N/A
Symbol IEC 60417-5036, for the enclosure of

N/A
electrically-operated water valves in external
hose-sets for connection of an appliance to the
water mains, if the working voltage exceeds
extra-low voltage

Appliances manually filled have level mark or other

N/A
means to indicate when they filled to their rated
capacity, unless they cannot be filled beyond this
capacity. Indication visible when appliance being
filled. (IEC 60335-2-98)

If temperature of water vapour exceeds 60 °C,

N/A
appliance marked with symbol IEC 60417-5597
(2002-10) or (IEC 60335-2-98/A2)

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 7 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

with substance of the following:

N/A
CAUTION: Hot water vapour
(IEC 60335-2-98/A2)

7.2 Warning for stationary appliances for multiple

N/A
supply

Warning placed in vicinity of terminal cover N/A

7.3 Range of rated values marked with the lower and

N/A
upper limits separated by a hyphen

Different rated values marked with the values

N/A
separated by an oblique stroke

7.4 Appliances adjustable for different rated voltages,

N/A
the voltage setting is clearly discernible

Requirement met if frequent changes are not

N/A
required and the rated voltage to which the
appliance is to be adjusted is determined from a
wiring diagram

7.5 Appliances with more than one rated voltage or one

N/A
or more rated voltage ranges, marked with rated
input or rated current for each rated voltage or
range, unless

the power input is related to the arithmetic mean

N/A
value of the rated voltage range

Relation between marking for upper and lower limits

N/A
of rated power input or rated current and voltage is
clear

7.6 Correct symbols used P
Symbol for nature of supply placed next to rated

N/A
voltage

Symbol for class II appliances placed unlikely to be

N/A
confused with other marking

Units of physical quantities and their symbols

P
according to international standardized system

7.7 Connection diagram fixed to appliances to be

N/A
connected to more than two supply conductors and
appliances for multiple supply, unless

correct mode of connection is obvious N/A

7.8 Except for type Z attachment, terminals for connection to the supply mains indicated

----

as follows:

- marking of terminals exclusively for the neutral

N/A
conductor (letter N)

- marking of protective earthing terminals (symbol

N/A
IEC 60417-5019)

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 8 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- marking not placed on removable parts N/A

7.9 Marking or placing of switches which may cause a

P
hazard

7.10 Indications of switches on stationary appliances and
controls on all appliances by use of figures, letters

By symbols and other visual
means

P

or other visual means............................................ :

This applies also to switches which are part of a

P

control

If figures are used, the off position indicated by the

N/A

figure 0

The figure 0 indicates only OFF position, unless no

N/A

confusion with the OFF position

7.11 Indication for direction of adjustment of controls P

7.12 Instructions for safe use provided P

Details concerning precautions during user

P

maintenance

The instructions state that: ----

- the appliance is not to be used by persons

P
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction

- children being supervised not to play with the

P
appliance

For a part of class III construction supplied from a

N/A
detachable power supply unit, the instructions state
that the appliance is only to be used with the unit
provided

Instructions for class III appliances state that it must

P
only be supplied at SELV, unless

it is a battery-operated appliance, the battery being

N/A
charged outside the appliance

Instructions include details regarding filling, cleaning

P
and descaling (IEC 60335-2-98)

The instructions shall state the substance of the following: (IEC 60335-2-98) ----

- care should be taken when using the appliance due

N/A

to the emission of hot water vapour;
(IEC 60335-2-98)

- unplug the appliance during filling and cleaning.

P

(IEC 60335-2-98)

The instructions for electrode-type appliances shall include the substance of the

----

following (IEC 60335-2-98):

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 9 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- the composition and quantity of solution to be used

N/A

and advice not to use an excessive amount of salt;
(IEC 60335-2-98)

- the appliance is not to be operated from a d.c.

N/A

supply. (IEC 60335-2-98)

If symbol IEC 60417-5597 (2002-10) used, meaning

N/A
explained (IEC 60335-2-98/A2)

7.12.1 Sufficient details for installation supplied P
For an appliance intended to be permanently

N/A
connected to the water mains and not connected by
a hose-set, this is stated

The installation instructions for appliances intended

N/A
to be connected to the water mains shall state the
maximum permissible water pressure in pascals.
(IEC 60335-2-98)

7.12.2 Stationary appliances not fitted with means for

N/A
disconnection from the supply mains having a
contact separation in all poles that provide full
disconnection under overvoltage category III, the
instructions state that means for disconnection
must be incorporated in the fixed wiring in
accordance with the wiring rules

7.12.3 Insulation of the fixed wiring in contact with parts

N/A
exceeding 50 K during clause 11; instructions state
that the fixed wiring must be protected

7.12.4 Instructions for built-in appliances: ----

- dimensions of space N/A

- dimensions and position of supporting and fixing N/A

- minimum distances between parts and

N/A
surrounding structure

- minimum dimensions of ventilating openings and

N/A
arrangement

- connection to supply mains and interconnection of

N/A
separate components

- allow disconnection of the appliance after

N/A
installation, by accessible plug or a switch in the
fixed wiring, unless

a switch complying with 24.3 N/A

7.12.5 Replacement cord instructions, type X attachment

N/A
with a specially prepared cord

Replacement cord instructions, type Y attachment N/A
Replacement cord instructions, type Z attachment N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 10 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

7.12.6 Caution in the instructions for appliances

N/A
incorporating a non-self-resetting thermal cut-out
that is reset by disconnection of the supply mains, if
this cut-out is required to comply with the standard

7.12.7 Instructions for fixed appliances stating how the

N/A
appliance is to be fixed

7.12.8 Instructions for appliances connected to the water mains: ----

- max. inlet water pressure (Pa) ............................ : N/A

- min. inlet water pressure, if necessary (Pa) ........ : N/A

Instructions concerning new and old hose-sets for

N/A
appliances connected to the water mains by
detachable hose-sets

7.13 Instructions and other texts in an official language English P

7.14 Marking clearly legible and durable, rubbing test as

P
specified

7.15 Markings on a main part P
Marking clearly discernible from the outside, if

P
necessary after removal of a cover

For portable appliances, cover can be removed or

P
opened without a tool

For stationary appliances, name, trademark or

N/A
identification mark and model or type reference
visible after installation

For fixed appliances, name, trademark or

N/A
identification mark and model or type reference
visible after installation according to the instructions

Indications for switches and controls placed on or

P
near the components. Marking not on parts which
can be positioned or repositioned in such a way that
the marking is misleading

Symbol IEC 60417-5597 (2002-10) or

N/A
(IEC 60335-2-98/A2)

marking relating to hot water vapour near vapour

N/A
outlet (IEC 60335-2-98/A2)

7.16 Marking of a possible replaceable thermal link or

N/A
fuse link clearly visible with regard to replacing the
link

8 PROTECTION AGAINST ACCESS TO LIVE PARTS ----

8.1 Adequate protection against accidental contact with

Supplied at SELV P
live parts

8.1.1 Requirement applies for all positions, detachable

N/A
parts removed

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 11 of 116 Report No.: 160421073GZU-003

61032, with a force not exceeding 1

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Lamps behind a detachable cover not removed, if

N/A
conditions met

Insertion or removal of lamps, protection against

N/A
contact with live parts of the lamp cap

Use of test probe B of IEC 61032, with a force not

N/A
exceeding 1 N: no contact with live parts

Use of test probe B of IEC 61032 through openings,

N/A
with a force of 20 N: no contact with live parts

8.1.2 Use of test probe 13 of IEC 61032, with a force not

N/A
exceeding 1 N, through openings in class 0
appliances and class II appliances/constructions: no
contact with live parts

Test probe 13 also applied through openings in

N/A
earthed metal enclosures having a non-conductive
coating: no contact with live parts

8.1.3 For appliances other than class II, use of test

N/A
probe 41 of IEC
N: no contact with live parts of visible glowing
heating elements

8.1.4 Accessible part not considered live if: ----

- safety extra-low a.c. voltage: peak value not

N/A
exceeding 42,4 V

- safety extra-low d.c. voltage: not exceeding 42,4 V Supplied at SELV: 24VDC P

- or separated from live parts by protective

N/A
impedance

If protective impedance: d.c. current not exceeding

N/A
2 mA, and

a.c. peak value not exceeding 0,7 mA N/A

- for peak values over 42,4 V up to and including

N/A
450 V, capacitance not exceeding 0,1 µF

- for peak values over 450 V up to and including

N/A
15 kV, discharge not exceeding 45 µC

- for peak values over 15kV, the energy in the

N/A
discharge not exceeding 350 mJ

8.1.5 Live parts protected at least by basic insulation before installation or assembly: ----

- built-in appliances N/A

- fixed appliances N/A

- appliances delivered in separate units N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 12 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

8.2 Class II appliances and constructions constructed

N/A
so that there is adequate protection against
accidental contact with basic insulation and metal
parts separated from live parts by basic insulation
only

Only possible to touch parts separated from live

N/A
parts by double or reinforced insulation

9 STARTING OF MOTOR-OPERATED APPLIANCES ---­ Requirements and tests are specified in part 2

N/A
when necessary

10 POWER INPUT AND CURRENT

10.1 Power input at normal operating temperature, rated

(see appended table) P
voltage and normal operation not deviating from
rated power input by more than shown in table 1 . :

For electrode-type appliances, negative deviation not

N/A
limited (IEC 60335-2-98/A1)

Test carried out at upper and lower limits of the

N/A
ranges for appliances with one or more rated
voltage ranges, unless

the rated power input is related to the arithmetic

N/A
mean value

10.2 Current at normal operating temperature, rated

(see appended table) P
voltage and normal operation not deviating from

rated current by more than shown in table 2 ......... :

Test carried out at upper and lower limits of the

N/A
ranges for appliances with one or more rated
voltage ranges, unless

the rated current is related to the arithmetic mean

N/A
value of the range

11 HEATING ----

11.1 No excessive temperatures in normal use P

11.2 The appliance is held, placed or fixed in position as

P

described .............................................................. :

11.3 Temperature rises, other than of windings,

P
determined by thermocouples

Temperature rises of windings determined by

N/A
resistance method, unless

the windings are non-uniform or it is difficult to

N/A
make the necessary connections

11.4 Electrode-type appliances are supplied at 1,06 times

N/A
rated voltage (IEC 60335-2-98)

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 13 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

If temperature rise limits exceeded in appliances

N/A
incorporating motors, transformers or electronic
circuits, and the power input is lower than rated
power input, test repeated with appliance supplied at
1,06 times rated voltage (IEC 60335-2-98)

11.5 Motor-operated appliances operated under normal

24VDC x 1,06=25,44V P
operation at most unfavourable voltage between

0,94 and 1,06 times rated voltage (V) ................... :

11.6 Combined appliances are operated as heating

N/A
appliances (IEC 60335-2-98)

11.7 Appliances are operated until steady conditions are

P
established (IEC 60335-2-98)

11.8 Temperature rises monitored continuously and not

(see appended table) P

exceeding the values in table 3 ............................ :

The temperature rise limits of motors, transformers

N/A
and components of electronic circuits, including parts
directly influenced by them, exceeded when
appliance operated at 1,15 times rated power input
(IEC 60335-2-98)

If the temperature rise of a motor winding exceeds

N/A
the value of table 3, or

if there is doubt with regard to classification of

N/A
insulation,

tests of annex C are carried out N/A
Sealing compound does not flow out P
Protective devices do not operate, except P
components in protective electronic circuits tested

N/A
for the number of cycles specified in 24.1.4

13 LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING

----

TEMPERATURE

13.1 Leakage current not excessive and electric strength

N/A
adequate

Electrode-type appliances supplied at 1,06 times

N/A
rated voltage (IEC 60335-2-98)

Motor-operated appliances and combined

N/A
appliances supplied at 1,06 times the rated voltage

(V) ......................................................................... :

Protective impedance and radio interference filters

N/A
disconnected before carrying out the tests

13.2 For class 0, class II and class III appliances,

Class III appliance N/A
leakage current measured by means of the circuit
described in figure 4 of IEC 60990

For other appliances, a low impedance ammeter

N/A
may be used

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 14 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Leakage current measurements ........................... : (see appended table) N/A

Electrode-type appliances, leakage current measured

N/A
between metallic mesh placed in water vapour,
10 mm from outlet, and accessible metal parts
including metal foil (IEC 60335-2-98/A1)

Leakage current not exceed 0,25 mA

N/A
(IEC 60335-2-98/A1)

13.3 The appliance is disconnected from the supply N/A

Electric strength tests according to table 4 ........... : (see appended table) N/A

No breakdown during the tests N/A
14 TRANSIENT OVERVOLTAGES ---­ Appliances withstand the transient over-voltages to

N/A
which they may be subjected

Clearances having a value less than specified in

(see appended table) N/A
table 16 subjected to an impulse voltage test, the

test voltage specified in table 6 ............................. :

No flashover during the test, unless N/A
of functional insulation if the appliance complies

N/A
with clause 19 with the clearance short-circuited

15 MOISTURE RESISTANCE ----

15.1 Enclosure provides the degree of moisture

N/A
protection according to classification of the
appliance

Compliance checked as specified in 15.1.1, taking

N/A
into account 15.1.2, followed by the electric strength
test of 16.3

No trace of water on insulation which can result in a

N/A
reduction of clearances or creepage distances
below values specified in clause 29

15.1.1 Appliances, other than IPX0, subjected to tests as

N/A

specified in IEC 60529 .......................................... :

Water valves containing live parts in external hoses

N/A
for connection of an appliance to the water mains
tested as specified for IPX7 appliances

15.1.2 Hand-held appliance turned continuously through

N/A
the most unfavourable positions during the test

Built-in appliances installed according to the

N/A
instructions

Appliances placed or used on the floor or table

N/A
placed on a horizontal unperforated support

Appliances normally fixed to a wall and appliances

N/A
with pins for insertion into socket-outlets are
mounted on a wooden board

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 15 of 116 Report No.: 160421073GZU-003

from the vertical for a period

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

For IPX3 appliances, the base of wall mounted

N/A
appliances is placed at the same level as the pivot
axis of the oscillating tube

For IPX4 appliances, the horizontal centre line of

the appliance is aligned with the pivot axis of the
oscillating tube, and

for appliances normally used on the floor or table,

the movement is limited to two times 90° for a
period of 5 min, the support being placed at the
level of the pivot axis of the oscillating tube

Wall-mounted appliances, take into account the

distance to the floor stated in the instructions

Appliances normally fixed to a ceiling are mounted

underneath a horizontal unperforated support, the
pivot axis of the oscillating tube located at the level
of the underside of the support, and

for IPX4 appliances, the movement of the tube is

limited to two times 90°
of 5 min

Appliances with type X attachment fitted with a

flexible cord as described

Detachable parts subjected to the relevant

treatment with the main part

However, if a part has to be removed for user

maintenance and a tool is needed, this part is not
removed

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

15.2 Spillage of liquid does not affect the electrical

N/A
insulation

Appliances with type X attachment fitted with a

N/A
flexible cord as described

Appliances incorporating an appliance inlet tested

N/A
with or without an connector, whichever is most
unfavourable

Detachable parts are removed N/A
Overfilling test with additional amount of

N/A

water, over a period of 1 min (l) ............................ :

In case of doubt, the spillage test is carried out with

N/A
the appliance deviating from the normal position of
use by an angle not exceeding 5 ° (IEC 60335-2-98)

Appliances intended to be connected to water mains

N/A
operated until maximum water level reached. Inlet
valve held open and filling continued for 15 min after
first evidence of overflow or (IEC 60335-2-98)

until inflow stops automatically (IEC 60335-2-98) N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 16 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

The appliance withstands the electric strength test

N/A
of 16.3

No trace of water on insulation that can result in a

N/A
reduction of clearances or creepage distances
below values specified in clause 29

15.3 Appliances proof against humid conditions N/A
Checked by test Cab: Damp heat steady state in

N/A
IEC 60068-2-78

Detachable parts removed and subjected, if

N/A
necessary, to the humidity test with the main part

Humidity test for 48 h in a humidity cabinet N/A
Reassembly of those parts that may have been

N/A
removed

The appliance withstands the tests of clause 16 N/A
16 LEAKAGE CURRENT AND ELECTRIC STRENGTH ----

16.1 Leakage current not excessive and electric strength

N/A
adequate

Protective impedance disconnected from live parts

N/A
before carrying out the tests

Tests carried out at room temperature and not

N/A
connected to the supply

16.2 Single-phase appliances: test voltage 1,06 times

N/A

rated voltage (V) ................................................... :

Three-phase appliances: test voltage 1,06 times

N/A

rated voltage divided by √3 (V) ............................. :

Leakage current measurements ........................... : (see appended table) N/A

Limit values doubled if: ----

- all controls have an off position in all poles, or N/A

- the appliance has no control other than a thermal

N/A
cut-out, or

- all thermostats, temperature limiters and energy

N/A
regulators do not have an off position, or

- the appliance has radio interference filters N/A
With the radio interference filters disconnected, the

(see appended table) N/A

leakage current do not exceed limits specified ..... :

16.3 Electric strength tests according to table 7 ........... : (see appended table) N/A

Test voltage applied between the supply cord and

(see appended table) N/A
inlet bushing and cord guard and cord anchorage

as specified ........................................................... :

No breakdown during the tests N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 17 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

17 OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS

----

No excessive temperatures in transformer or

(see appended table) N/A
associated circuits in event of short-circuits likely to

occur in normal use .............................................. :

Appliance supplied with 1,06 or 0,94 times rated

N/A
voltage under the most unfavourable short-circuit or

overload likely to occur in normal use (V) ............. :

Basic insulation is not short-circuited N/A
Temperature rise of insulation of the conductors of

N/A
safety extra-low voltage circuits not exceeding the
relevant value specified in table 3 by more than
15 K

Temperature of the winding not exceeding the value

N/A
specified in table 8

However, limits do not apply to fail-safe

N/A
transformers complying with sub-clause 15.5 of
IEC 61558-1

18 ENDURANCE ---­ Requirements and tests are specified in part 2

N/A
when necessary

19 ABNORMAL OPERATION ----

19.1 The risk of fire, mechanical damage or electric

P
shock under abnormal or careless operation
obviated

Electronic circuits so designed and applied that a

(see appended table) N/A

fault will not render the appliance unsafe ............. :

Appliances incorporating heating elements

N/A
subjected to the tests of 19.2 and 19.3, and

if the appliance also has a control that limit the

N/A
temperature during clause 11 it is subjected to the
test of 19.4, and

if applicable, to the test of 19.5 N/A
Appliances incorporating PTC heating elements are

N/A
also subjected to the test of 19.6

Appliances incorporating motors subjected to the

P
tests of 19.7 to 19.10, as applicable

Appliances incorporating electronic circuits

N/A
subjected to the tests of 19.11 and 19.12, as
applicable

Appliances incorporating contactors or relays

N/A
subjected to the test of 19.14, being carried out
before the tests of 19.11

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 18 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Appliances incorporating voltage selector switches

N/A
subjected to the test of 19.15

Unless otherwise specified, the tests are continued

N/A
until a non-self-resetting thermal cut-out operates,
or

until steady conditions are established P
If a heating element or intentionally weak part

N/A
becomes open-circuited, the relevant test is
repeated on a second sample

19.2 Test of appliances with heating elements with

N/A
restricted heat dissipation; test voltage (V), power

input of 0,85 times rated power input (W) ............. :

Container of electrode-type appliances filled with

N/A
saturated solution of NaCl at 20 °C ± 5 °C, appliance
being supplied at rated voltage (IEC60335-2-98)

19.3 Test of 19.2 repeated; test voltage (V), power input

N/A

of 1,24 times rated power input (W) ..................... :

Test not applicable to electrode-type appliances

N/A
(IEC60335-2-98)

19.4 Appliances only filled with sufficient water to cover

N/A
heating elements (IEC60335-2-98)

Fans switched off (IEC60335-2-98) N/A

19.5 Test of 19.4 repeated on class 0I and I appliances

N/A
with tubular sheathed or embedded heating
elements. No short-circuiting, but one end of the
element connected to the sheath

The test repeated with reversed polarity and the

N/A
other end of the heating element connected to the
sheath

The test is not carried out on appliances intended to

N/A
be permanently connected to fixed wiring and on
appliances where an all-pole disconnection occurs
during the test of 19.4

19.6 Appliances with PTC heating elements tested at

N/A
rated voltage, establishing steady conditions

The working voltage of the PTC heating element is

N/A
increased by 5 % and the appliance is operated
until steady conditions are re-established. The
voltage is then increased in similar steps until
1,5 times working voltage or until the PTC heating

element ruptures (V) ............................................. :

19.7 Stalling test by locking the rotor if the locked rotor

P
torque is smaller than the full load torque, or

locking moving parts of other appliances N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 19 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Locked rotor, capacitors open-circuited one at a

N/A
time

Test repeated with capacitors short-circuited one at

N/A
a time, unless

capacitor is of class P2 of IEC 60252-1 N/A
Appliances with timer or programmer supplied with

N/A
rated voltage for each of the tests, for a period

equal to the maximum period allowed .................. :

Other appliances supplied with rated voltage for a

N/A

period as specified ................................................ :

Winding temperatures not exceeding values

(see appended table) P

specified in table 8 ................................................ :

19.8 Multi-phase motors operated at rated voltage with

N/A
one phase disconnected

19.9 Running overload test on appliances incorporating

N/A
motors intended to be remotely or automatically
controlled or liable to be operated continuously

Motor-operated and combined appliances for which

N/A

30.2.3 is applicable and that use overload protective
devices relying on electronic circuits to protect the
motor windings, are also subjected to the test

Winding temperatures not exceeding values as

(see appended table) N/A

specified ................................................................ :

19.10 Series motor operated at 1,3 times rated voltage for

N/A

1 min (V) ............................................................... :

During the test, parts not being ejected from the

N/A
appliance

19.11 Electronic circuits, compliance checked by

N/A
evaluation of the fault conditions specified in

19.11.2 for all circuits or parts of circuits, unless

they comply with the conditions specified in 19.11.1 P
Appliances incorporating an electronic circuit that

N/A
relies upon a programmable component to function
correctly, subjected to the test of 19.11.4.8, unless

restarting does not result in a hazard N/A
Appliances having a device with an off position

N/A
obtained by electronic disconnection, or a device
placing the appliance in a stand-by mode, subjected
to the tests of 19.11.4

If the safety of the appliance under any of the fault

N/A
conditions depends on the operation of a miniature
fuse-link complying with IEC 60127, the test of

19.12 is carried out

During and after each test the following is checked: ----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 20 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- the temperature of the windings do not exceed the

N/A

values specified in table 8

- the appliance complies with the conditions

N/A
specified in 19.13

- any current flowing through protective impedance

N/A
not exceeding the limits specified in 8.1.4

If a conductor of a printed board becomes open-circuited, the appliance is

considered to have withstood the particular test, provided both of the following
conditions are met:

- the base material of the printed circuit board

N/A
withstands the test of annex E

- any loosened conductor does not reduce

N/A
clearance or creepage distances between live parts
and accessible metal parts below the values
specified in clause 29

19.11.1 Fault conditions a) to g) in 19.11.2 are not applied to circuits or parts of circuits
meeting both of the following conditions:

- the electronic circuit is a low-power circuit, that is,

N/A
the maximum power at low-power points does not
exceed 15 W according to the tests specified

- the protection against electric shock, fire hazard,

N/A
mechanical hazard or dangerous malfunction of
other parts of the appliance does not rely on the
correct functioning of the electronic circuit

----

----

19.11.2 Fault conditions applied one at a time, the appliance operating under conditions

---­specified in clause 11, but supplied at rated voltage, duration of the tests as
specified:

a) short circuit of functional insulation if clearances

N/A
or creepage distances are less than the values
specified in clause 29

b) open circuit at the terminals of any component N/A
c) short circuit of capacitors, unless N/A
they comply with IEC 60384-14 N/A
d) short circuit of any two terminals of an electronic

N/A
component, other than integrated circuits

This fault condition is not applied between the two

N/A
circuits of an optocoupler

e) failure of triacs in the diode mode N/A
f) failure of microprocessors and integrated circuits N/A
g) failure of an electronic power switching device N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 21 of 116 Report No.: 160421073GZU-003

n

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Each low power circuit is short-circuited by

N/A
connecting the low-power point to the pole of the
supply source from which the measurements were
made

19.11.3 If the appliance incorporates a protective electronic

N/A
circuit which operates to ensure compliance with
clause 19, the relevant test is repeated with a single
fault simulated, as indicated in a) to g) of 19.11.2

19.11.4 Appliances having a device with an off position

N/A
obtained by electronic disconnection, or

a device that can be placed in the stand-by mode, N/A
subjected to the tests of 19.11.4.1 to 19.11.4.7, the

N/A
device being set in the off position or in the stand-by
mode

Appliances incorporating a protective electronic

N/A
circuit subjected to the tests of 19.11.4.1 to

19.11.4.7, the tests being carried out after the
protective electronic circuit has operated, except
that

appliances operated for 30 s or 5 min during the

N/A
test of 19.7 are not subjected to the tests for
electromagnetic phenomena.

Surge protective devices disconnected, unless N/A
They incorporate spark gaps N/A

19.11.4.1 The appliance is subjected to electrostatic

N/A
discharges in accordance with IEC 61000-4-2, test
level 4

19.11.4.2 The appliance is subjected to radiated fields in

N/A
accordance with IEC 61000-4-3, test level 3

19.11.4.3 The appliance is subjected to fast transient bursts i

N/A
accordance with IEC 61000-4-4, test level 3 or 4 as
specified

19.11.4.4 The power supply terminals of the appliance

N/A
subjected to voltage surges in accordance with
IEC 61000-4-5, test level 3 or 4 as specified

Earthed heating elements in class I appliances

N/A
disconnected

19.11.4.5 The appliance is subjected to injected currents in

N/A
accordance with IEC 61000-4-6, test level 3

19.11.4.6 Appliances having a rated current not exceeding

N/A
16 A are subjected to the class 3 voltage dips and
interruptions in accordance with IEC 61000-4-11

Appliances having a rated current exceeding 16 A

N/A
are subjected to the class 3 voltage dips and
interruptions in accordance with IEC 61000-4-34

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 22 of 116 Report No.: 160421073GZU-003

ot emit flames,

complies with

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

19.11.4.7 The appliance is subjected to mains signals in

N/A
accordance with IEC 61000-4-13, test level class 2

19.11.4.8 The appliance is supplied at rated voltage and

N/A
operated under normal operation. After 60 s the
power supply is reduced to a level such that the
appliance ceases to respond or parts controlled by
the programmable component cease to operate

The appliance continues to operate normally, or N/A
requires a manual operation to restart N/A

19.12 If the safety of the appliance for any of the fault

N/A
conditions specified in 19.11.2 depends on the
operation of a miniature fuse-link complying with
IEC 60127, the test is repeated, measuring the
current flowing through the fuse-link; measured

current (A); rated current of the fuse-link (A) ........ :

19.13 During the tests the appliance does n

P
molten metal, poisonous or ignitable gas in
hazardous amounts

Temperature rises not exceeding the values shown

(see appended table) P

in table 9 ............................................................... :

Compliance with clause 8 not impaired P
If the appliance can still be operated it

N/A

20.2

Insulation, other than of class III appliances or class III constructions that do not

---­contain live parts, withstands the electric strength test of 16.3, the test voltage as
specified in table 4:

- basic insulation (V) .............................................. : 1000V N/A

- supplementary insulation (V) .............................. : 1750V N/A

- reinforced insulation (V) ...................................... : 3000V N/A

After operation or interruption of a control,

N/A
clearances and creepage distances across the
functional insulation withstand the electric strength
test of 16.3, the test voltage being twice the
working voltage

The appliance does not undergo a dangerous

P
malfunction, and

no failure of protective electronic circuits, if the

N/A
appliance is still operable

Appliances tested with an electronic switch in the off position, or in the stand-by

----

mode:

- do not become operational, or P

- if they become operational, do not result in a

N/A
dangerous malfunction during or after the tests of

19.11.4

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 23 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

If the appliance contains lids or doors that are controlled by one or more interlocks,

----

one of the interlocks may be released provided that:

- the lid or door does not move automatically to an

N/A
open position when the interlock is released, and

- the appliance does not start after the cycle in

N/A
which the interlock was released

19.14 Appliances operated under the conditions of

N/A
clause 11, any contactor or relay contact operating
under the conditions of clause 11 being
short-circuited

For a relay or contactor with more than one contact,

N/A
all contacts are short-circuited at the same time

A relay or contactor operating only to ensure the

N/A
appliance is energized for normal use is not
short-circuited

If more than one relay or contactor operates in

N/A
clause 11, they are short-circuited in turn

19.15 For appliances with a mains voltage selector switch,

N/A
the switch is set to the lowest rated voltage position
and the highest value of rated voltage is applied

20 STABILITY AND MECHANICAL HAZARDS ----

20.1 Appliances having adequate stability P
Tilting test through an angle of 10°, appliance

P
placed on an inclined plane/horizontal support, not
connected to the supply mains; appliance does not
overturn

Tilting test repeated on appliances with heating

N/A
elements, angle of inclination increased to 15°

Possible heating test in overturned position;

N/A
temperature rise does not exceed values shown in
table 9

20.2 Moving parts adequately arranged or enclosed as to

N/A
provide protection against personal injury

Protective enclosures, guards and similar parts are

N/A
non-detachable, and

have adequate mechanical strength N/A
Enclosures that can be opened by overriding an

N/A
interlock are considered to be detachable parts

Self-resetting thermal cut-outs and overcurrent

N/A
protective devices not causing a hazard by
unexpected closure

Not possible to touch dangerous moving parts with

N/A
the test probe described

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 24 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

21 MECHANICAL STRENGTH ----

21.1 Appliance has adequate mechanical strength and is
constructed as to withstand rough handling

Checked by applying 3 blows to every point of the

enclosure like to be weak, in accordance with test
Ehb of IEC 60068-2-75, spring hammer test, with
an impact energy of 0,5 J

The appliance shows no damage impairing

compliance with this standard, and

compliance with 8.1, 15.1 and clause 29 not

impaired

If doubt, supplementary or reinforced insulation

subjected to the electric strength test of 16.3

If necessary, repetition of groups of three blows on

a new sample

21.2 Accessible parts of solid insulation having strength
to prevent penetration by sharp implements

Test not applicable if the thickness of

supplementary insulation is at least 1 mm and
reinforced insulation at least 2 mm

The insulation is tested as specified, and does

withstand the electric strength test of 16.3

P

(see appended table) P

P

P

N/A

N/A

N/A

N/A

N/A

22 CONSTRUCTION ----

22.1 Appliance marked with the first numeral of the IP

IPX0 N/A
system, relevant requirements of IEC 60529 are
fulfilled

22.2 Stationary appliance: means to ensure all-pole disconnection from the supply being

----

provided:

- a supply cord fitted with a plug, or N/A

- a switch complying with 24.3, or N/A

- a statement in the instruction sheet that a

N/A
disconnection incorporated in the fixed wiring is to
be provided, or

- an appliance inlet N/A
Singe-pole switches and single-pole protective

N/A
devices for the disconnection of heating elements in
single-phase, permanently connected class 01 and
class I appliances, connected to the phase
conductor

22.3 Appliance provided with pins: no undue strain on

N/A
socket-outlets

Applied torque not exceeding 0,25 Nm N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 25 of 116 Report No.: 160421073GZU-003

of an automatic switching device incorporated within

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Pull force of 50 N to each pin after the appliance

N/A
has being placed in the heating cabinet; when
cooled to room temperature the pins are not
displaced by more than 1 mm

Each pin subjected to a torque of 0,4 Nm; the pins

N/A

are not rotating, unless

rotating does not impair compliance with this

N/A

standard

22.4 Appliance for heating liquids and appliance causing

N/A
undue vibration not provided with pins for insertion
into socket-outlets

22.5 No risk of electric shock when touching the pins of

N/A
the plug, for appliances having a capacitor with
rated capacitance exceeding 0,1 µF, the appliance
being disconnected from the supply at the instant of
voltage peak

Voltage not exceeding 34 V (V) ............................ : N/A

22.6 Electrical insulation not affected by condensing

N/A
water or leaking liquid

Electrical insulation of class II appliances not

N/A
affected if a hose ruptures or seal leaks

In case of doubt, test as described N/A
Drain holes be at least 5 mm in diameter or 20 mm²

N/A
in area with minimum dimension of at least 3 mm
(IEC60335-2-98)

22.7 Adequate safeguards against the risk of excessive

P
pressure in appliances containing liquid or gases or
having steam-producing devices

22.8 Electrical connections not subject to pulling during

P
cleaning of compartments to which access can be
gained without the aid of a tool, and that are likely to
be cleaned in normal use

22.9 Insulation, internal wiring, windings, commutators

P
and slip rings not exposed to oil, grease or similar
substances, unless

the substance has adequate insulating properties P

22.10 Not possible to reset voltage-maintained

N/A
non-self-resetting thermal cut-outs by the operation

the appliance, if:

- a non-self-resetting thermal cut-out is required by

N/A
the standard, and

- a voltage maintained non-self-resetting thermal

N/A
cut-out is used to meet it

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 26 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Non-self-resetting thermal motor protectors have a

N/A

trip-free action, unless

they are voltage maintained N/A
Reset buttons of non-self-resetting controls so

N/A
located or protected that accidental resetting is
unlikely

22.11 Reliable fixing of non-detachable parts that provide

P
the necessary degree of protection against electric
shock, moisture or contact with moving parts

Obvious locked position of snap-in devices used for

N/A
fixing such parts

No deterioration of the fixing properties of snap-in

N/A
devices used in parts that are likely to be removed
during installation or servicing

Tests as described P

22.12 Handles, knobs etc. fixed in a reliable manner P
Fixing in wrong position of handles, knobs etc.

P
indicating position of switches or similar
components not possible

Axial force 15 N applied to parts, the shape being

P
so that an axial pull is unlikely to be applied

Axial force 30 N applied to parts, the shape being

P
so that an axial pull is likely to be applied

22.13 Unlikely that handles, when gripped as in normal

N/A
use, make the operator’s hand touch parts having a
temperature rise exceeding the value specified for
handles which are held for short periods only

22.14 No ragged or sharp edges creating a hazard for the

P
user in normal use, or during user maintenance

No exposed pointed ends of self-tapping screws or

P
other fasteners, likely to be touched by the user in
normal use or during user maintenance

22.15 Storage hooks and the like for flexible cords smooth

N/A
and well rounded

22.16 Automatic cord reels cause no undue abrasion or

N/A
damage to the sheath of the flexible cord, no
breakage of conductors strands and no undue wear
of contacts

Cord reel tested with 6000 operations, as specified N/A
Electric strength test of 16.3, voltage of 1000 V

N/A
applied

22.17 Spacers not removable from the outside by hand or

N/A
by means of a screwdriver or a spanner

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 27 of 116 Report No.: 160421073GZU-003

Parts connected by protective impedance separated

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

22.18 Current-carrying parts and other metal parts

P

resistant to corrosion

22.19 Driving belts not relied upon to provide the required

N/A
level of insulation, unless

constructed to prevent inappropriate replacement N/A

22.20 Direct contact between live parts and thermal

N/A
insulation effectively prevented, unless

material used is non-corrosive, non-hygroscopic

N/A
and non-combustible

22.21 Wood, cotton, silk, ordinary paper and fibrous or

P
hygroscopic material not used as insulation, unless

impregnated N/A
This requirement does not apply to magnesium

N/A
oxide and mineral ceramic fibres used for the
electrical insulation of heating elements

22.22 Appliances not containing asbestos P

22.23 Oils containing polychlorinated biphenyl (PCB) not

P
used

22.24 Bare heating elements, except in class III

N/A
appliances or class III constructions that do not
contain live parts, adequately supported

In case of rupture, the heating conductor is unlikely

N/A
to come in contact with accessible metal parts

22.25 Sagging heating conductors, except in class III

N/A
appliances or class III constructions that do not
contain live parts, cannot come into contact with
accessible metal parts

22.26 For class III constructions the insulation between

P
parts operating at safety extra-low voltage and other
live parts complies with the requirements for double
or reinforced insulation

22.27

N/A
by double or reinforced insulation

22.28 Metal parts of class II appliances conductively

N/A
connected to gas pipes or in contact with water,
separated from live parts by double or reinforced
insulation

22.29 Class II appliances permanently connected to fixed

N/A
wiring so constructed that the required degree of
access to live parts is maintained after installation

22.30 Parts serving as supplementary or reinforced

N/A
insulation fixed so that they cannot be removed
without being seriously damaged, or

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 28 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

so constructed that they cannot be replaced in an

N/A
incorrect position, and so that if they are omitted,
the appliance is rendered inoperable or manifestly
incomplete

22.31 Neither clearances nor creepage distances over
supplementary and reinforced insulation reduced
below values specified in clause 29 as a result of
wear

Neither clearances nor creepage distances

between live parts and accessible parts reduced
below values for supplementary insulation if wires,
screws etc. become loose

22.32 Supplementary and reinforced insulation
constructed or protected against pollution so that
clearances or creepage distances are not reduced
below the values in clause 29

Supplementary insulation of natural or synthetic

rubber resistant to ageing, or arranged and
dimensioned so that creepage distances are not
reduced below values specified in 29.2

Ceramic material not tightly sintered, similar

materials or beads alone not used as
supplementary or reinforced insulation

Insulating material in which heating conductors are

embedded is considered to be basic insulation, not
reinforced insulation

N/A

N/A

N/A

N/A

N/A

N/A

Oxygen bomb test at 70 °C for 96 h and 16 h at

N/A

room temperature

22.33 Conductive liquids that are or may become

N/A
accessible in normal use and conductive liquids that
are in contact with unearthed accessible metal parts
are not in direct contact with live parts

Liquids heated by using electrodes and in direct

N/A
contact with their live parts (IEC 60335-2-98)

For class II constructions, conductive liquids that

N/A
are or may become accessible in normal use and
conductive liquids that are in contact with unearthed
accessible metal parts, not in direct contact with
basic or reinforced insulation, unless

the reinforced insulation consists of at least 3 layers N/A
For class II constructions, conductive liquids which

N/A
are in contact with live parts, not in direct contact
with reinforced insulation, unless

the reinforced insulation consists of at least 3 layers N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 29 of 116 Report No.: 160421073GZU-003

n in a double insulation system if likely to be

Such parts being of metal, and their shafts or fixings

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

An air layer not used as basic or supplementary

N/A
insulatio
bridged by leaking liquid

22.34 Shafts of operating knobs, handles, levers etc. not

N/A
live, unless

the shaft is not accessible when the part is removed N/A

22.35 For other than class III constructions, handles,

N/A
levers and knobs, held or actuated in normal use,
not becoming live in the event of a failure of basic
insulation

N/A
are likely to become live in the event of a failure of
basic insulation, are either adequately covered by
insulation material or their accessible parts are
separated from their shafts or fixings by
supplementary insulation

This requirement does not apply to handles, levers

N/A
and knobs on stationary appliances, other than
those of electrical components, provided they are
reliably connected to an earthing terminal or
earthing contact, or separated from live parts by
earthed metal

Insulating material covering metal handles, levers

N/A
and knobs withstand the electric strength test of

16.3 for supplementary insulation

22.36 For appliances other than class III, handles

N/A
continuously held in the hand in normal use so
constructed that when gripped as in normal use, the
operators hand is not likely to touch metal parts,
unless

they are separated from live parts by double or

N/A
reinforced insulation

22.37 Capacitors in class II appliances not connected to

N/A
accessible metal parts and their casings, if of
metal, separated from accessible metal parts by
supplementary insulation, unless

the capacitors comply with 22.42 N/A

22.38 Capacitors not connected between the contacts of a

N/A
thermal cut-out

22.39 Lamp holders used only for the connection of lamps N/A

22.40 Motor-operated appliances and combined

N/A
appliances intended to be moved while in operation,
or having accessible moving parts, fitted with a
switch to control the motor. The actuating member
of the switch being easily visible and accessible

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 30 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

If the appliance cannot operate continuously,

N/A
automatically or remotely without giving rise to a
hazard, appliances for remote operation being fitted
with a switch for stopping the operation. The
actuating member of the switch being easily visible
and accessible

22.41 No components, other than lamps, containing
mercury

22.42 Protective impedance consisting of at least two
separate components

Values specified in 8.1.4 not exceeded if any one of

the components are short-circuited or
open-circuited

Resistors checked by the test of 14.1 a) in

IEC 60065

Capacitors checked by the tests for class Y

capacitors in IEC 60384-14

22.43 Appliances adjustable for different voltages,
accidental changing of the setting of the voltage
unlikely to occur

22.44 Appliances not having an enclosure that is shaped
or decorated like a toy

22.45 When air is used as reinforced insulation,
clearances not reduced below the values specified
in 29.1.3 due to deformation as a result of an
external force applied to the enclosure

22.46 For programmable protective electronic circuits
used to ensure compliance with the standard, the
software contains measures to control the
fault/error conditions in table R.1

P

N/A

N/A

N/A

N/A

N/A

P

N/A

N/A

Software that contains measures to control the

N/A
fault/error conditions specified in table R.2 is to be
specified in parts 2 for particular constructions or to
address specific hazards

These requirements are not applicable to software

N/A
used for functional purpose or compliance with
clause 11

22.47 Appliances connected to the water mains withstand

N/A
the water pressure expected in normal use

No leakage from any part, including any inlet water

N/A
hose

22.48 Appliances connected to the water mains

N/A
constructed to prevent backsiphonage of
non-potable water

22.49 For remote operation, the duration of operation is to

N/A
be set before the appliance can be started, unless

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 31 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

the appliance switches off automatically or can

N/A

operate continuously without hazard

22.50 Controls incorporated in the appliance take priority

N/A
over controls actuated by remote operation

22.51 There is a control on the appliance manually

N/A
adjusted to the setting for remote operation before
the appliance can be operated in this mode

There is a visual indication showing that the

N/A
appliance is adjusted for remote operation

These requirements not necessary on appliances that can operate as follows,

----

without giving rise to a hazard:

- continuously, or N/A

- automatically, or N/A

- remotely N/A

22.52 Socket-outlets on appliances accessible to the user

N/A
in accordance with the socket-outlet system used in
the country in which the appliance is sold

22.101 Vapour outlet of appliances incorporating means for

N/A
heating water be free from obstructions that could
give rise to a significant pressure within container
(IEC 60335-2-98)

Container vented to atmosphere, aperture being at

N/A
least 5 mm in diameter or 20 mm² in area with
minimum dimension of at least 3 mm
(IEC 60335-2-98)

22.102 Appliances for wall mounting have reliable provision

N/A
for fixing to wall, independent of connection to water
mains (IEC 60335-2-98)

22.103 Electrode-type appliances so constructed to ensure

N/A
that when filling aperture of container is open, both
electrodes disconnected to provide all-pole
disconnection under overvoltage category III
conditions (IEC 60335-2-98)

This requirement not apply to an appliance that

N/A
requires withdrawal of an appliance connector in
order to gain access to filling aperture
(IEC 60335-2-98/A1)

22.104 Appliances intended to be connected to water mains

N/A
withstand water pressure expected in normal use
(IEC 60335-2-98)

23 INTERNAL WIRING ----

23.1 Wireways smooth and free from sharp edges P
Wires protected against contact with burrs, cooling

P
fins etc.

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 32 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Wire holes in metal well-rounded or provided with

N/A

bushings

Wiring effectively prevented from coming into

P
contact with moving parts

23.2 Beads etc. on live wires cannot change their

N/A
position, and are not resting on sharp edges

Beads inside flexible metal conduits contained

N/A
within an insulating sleeve

23.3 Electrical connections and internal conductors

N/A
movable relatively to each other not exposed to
undue stress

Flexible metallic tubes not causing damage to

N/A
insulation of conductors

Open-coil springs not used N/A
Adequate insulating lining provided inside a coiled

N/A
spring, the turns of which touch one another

No damage after 10 000 flexings for conductors

N/A
flexed during normal use, or

100 flexings for conductors flexed during user

N/A
maintenance

Electric strength test of 16.3, 1000 V between live

N/A
parts and accessible metal parts

Not more than 10 % of the strands of any conductor

N/A
broken, and

not more than 30 % for wiring supplying circuits that

N/A
consume no more than 15 W

23.4 Bare internal wiring sufficiently rigid and fixed N/A

23.5 The insulation of internal wiring subjected to the

N/A
supply mains voltage withstanding the electrical
stress likely to occur in normal use

Basic insulation electrically equivalent to the basic

N/A
insulation of cords complying with IEC 60227 or
IEC 60245, or

no breakdown when a voltage of 2000 V is applied

N/A
for 15 min between the conductor and metal foil
wrapped around the insulation

23.6 Sleeving used as supplementary insulation on

N/A
internal wiring retained in position by clamping at
both ends, or

be such that it can only be removed by breaking or

N/A
cutting

23.7 The colour combination green/yellow only used for

N/A
earthing conductors

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 33 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

23.8 Aluminium wires not used for internal wiring

P

23.9 Stranded conductors not consolidated by soldering

N/A
where they are subjected to contact pressure,
unless

the contact pressure is provided by spring terminals N/A

23.10 The insulation and sheath of internal wiring,

N/A
incorporated in external hoses for the connection of
an appliance to the water mains, at least equivalent
to that of light polyvinyl chloride sheathed flexible
cord (60227 IEC 52)

24 COMPONENTS ----

24.1 Components comply with safety requirements in

P
relevant IEC standards

List of components ................................................ : (see appended table) P

If components have not been tested and found to

P
comply with relevant IEC standard for the number
of cycles specified, they are tested in accordance
with 24.1.1 to 24.1.9

For components mentioned in 24.1.1 to 24.1.9 no

P
additional tests specified in the relevant component
standard are necessary other than those specified
in 24.1.1 to 24.1.9

Components not tested and found to comply with

relevant IEC standard and components not marked
or not used in accordance with its marking, tested
under the conditions occurring in the appliance

Lampholders and starterholders that have not being

tested and found to comply with the relevant IEC
standard, tested as a part of the appliance and
additionally according to the gauging and
interchangeability requirements of the relevant IEC
standard

No additional tests specified for nationally

standardized plugs such as those detailed in
IEC/TR 60083 or connectors complying with the
standard sheets of IEC 60320-1 and IEC 60309

24.1.1 Capacitors likely to be permanently subjected to the
supply voltage and used for radio interference
suppression or for voltage dividing, complying with
IEC 60384-14

If the capacitors have to be tested, they are tested

according to annex F

24.1.2 Safety isolating transformers complying with
IEC 61558-2-6

P

N/A

N/A

N/A

N/A

N/A

If they have to be tested, they are tested according

N/A

to annex G

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 34 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

24.1.3 Switches complying with IEC 61058-1, the number

N/A

of cycles of operation being at least 10 000

If they have to be tested, they are tested according

N/A

to annex H

If the switch operates a relay or contactor, the

N/A

complete switching system is subjected to the test

If the switch only operates a motor staring relay

N/A
complying with IEC 60730-2-10 with the number of
cycles of a least 10 000 as specified, the complete
switching system need not be tested

24.1.4 Automatic controls complying with IEC 60730-1 with the relevant part 2. The number

----

of cycles of operation being at least:

- thermostats: ................................................. 10 000

- temperature limiters: ...................................... 1 000

- self-resetting thermal cut-outs: ......................... 300

- voltage maintained non-self-resetting thermal cut-

N/A
N/A
N/A
N/A

outs: .................................................................. 1 000

- other non-self-resetting thermal cut-outs: .......... 30

- timers:............................................................. 3 000

N/A
N/A

- energy regulators: ..................................... 10 000 N/A

The number of cycles for controls operating during

N/A
clause 11 need not be declared, if the appliance
meets the requirements of this standard when they
are short-circuited

Thermal motor protectors are tested in combination

N/A
with their motor under the conditions specified in
annex D

For water valves containing live parts and that are

N/A
incorporated in external hoses for connection of an
appliance to the water mains, the degree of
protection declared for subclause 6.5.2 of
IEC 60730-2-8 is IPX7

24.1.5 Appliance couplers complying with IEC 60320-1 N/A
However, for appliances classified higher than

N/A
IPX0, the appliance couplers complying with
IEC 60320-2-3

Interconnection couplers complying with

N/A
IEC 60320-2-2

24.1.6 Small lamp holders similar to E10 lampholders

N/A
complying with IEC 60238, the requirements for
E10 lampholders being applicable

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 35 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

24.1.7 For remote operation of the appliance via a

N/A
telecommunication network, the relevant standard
for the telecommunication interface circuitry in the
appliance is IEC 62151

24.1.8 The relevant standard for thermal links is

N/A

IEC 60691

Thermal links not complying with IEC 60691 are

N/A
considered to be an intentionally weak part for the
purposes of clause 19

24.1.9 Contactors and relays, other than motor starting

N/A
relays, tested as part of the appliance

They are also tested in accordance with clause 17

N/A
of IEC 60730-1, the number of cycles of operations
in 24.1.4 selected according to the contactor or

relay function in the appliance............................... :

24.2 Appliances not fitted with: ----

- switches or automatic controls in flexible cords N/A

- devices causing the protective device in the fixed

N/A
wiring to operate in the event of a fault in the
appliance

- thermal cut-outs that can be reset by soldering,

N/A
unless

the solder has a melding point of at least 230 °C N/A

24.3 Switches intended for all-pole disconnection of

N/A
stationary appliances are directly connected to the
supply terminals and have a contact separation in
all poles, providing full disconnection under
overvoltage category III conditions

24.4 Plugs and socket-outlets for extra-low voltage

N/A
circuits and heating elements, not interchangeable
with plugs and socket-outlets listed in
IEC/TR 60083 or IEC 60906-1 or with connectors
and appliance inlets complying with the standard
sheets of IEC 60320-1

24.5 Capacitors in auxiliary windings of motors marked

N/A
with their rated voltage and capacitance, and used
accordingly

Voltage across capacitors in series with a motor

N/A
winding does not exceed 1,1 times rated voltage,
when the appliance is supplied at 1,1 times rated
voltage under minimum load

24.6 Working voltage of motors connected to the supply

N/A
mains and having basic insulation that is
inadequate for the rated voltage of the appliance,
not exceeding 42 V

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 36 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

In addition, the motors comply with the

N/A

requirements of annex I

24.7 Detachable hose-sets for connection of appliances

N/A
to the water mains comply with IEC 61770

They are supplied with the appliance N/A
Appliances intended to be permanently connected

N/A
to the water mains not connected by a detachable
hose-set

24.8 Motor running capacitors in appliances for which

N/A

30.2.3 is applicable and that are permanently
connected in series with a motor winding, not
causing a hazard in event of a failure

One or more of the following conditions are to be met: ----

- the capacitors are of class P2 according to

N/A
IEC 60252-1

- the capacitors are housed within a metallic or

N/A
ceramic enclosure

- the distance of separation of the outer surface to

N/A
adjacent non-metallic parts exceeds 50 mm

- adjacent non-metallic parts within 50 mm

N/A
withstand the needle-flame test of annex E

- adjacent non-metallic parts within 50 mm

N/A
classified as at least V-1 according to
IEC 60695-11-10

24.101 Thermal cut-outs incorporated in appliances for

N/A
compliance with clause 19 not be self-resetting
(IEC 60335-2-98)

25 SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS ----

25.1 Appliance not intended for permanent connection to fixed wiring, means for

----

connection to the supply:

- supply cord fitted with a plug, N/A

- an appliance inlet having at least the same degree

N/A
of protection against moisture as required for the
appliance, or

- pins for insertion into socket-outlets N/A

25.2 Appliance not provided with more than one means

P
of connection to the supply mains

Stationary appliance for multiple supply may be

N/A
provided with more than one means of connection,
provided electric strength test of 1250 V for 1 min
between each means of connection causes no
breakdown

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 37 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

25.3 Appliance intended to be permanently connected to fixed wiring provided with one of

----

the following means for connection to the supply mains:

- a set of terminals allowing the connection of a

N/A
flexible cord

- a fitted supply cord N/A

- a set of supply leads accommodated in a suitable

N/A
compartment

- a set of terminals for the connection of cables of

N/A
fixed wiring, cross-sectional areas specified in 26.6,
and the appliance allows the connection of the
supply conductors after the appliance has been
fixed to its support

- a set of terminals and cable entries, conduit

N/A
entries, knock-outs or glands, allowing connection
of appropriate types of cable or conduit, and the
appliance allows the connection of the supply
conductors after the appliance has been fixed to its
support

For a fixed appliance constructed so that parts can

N/A
be removed to facilitate easy installation, this
requirement is met if it is possible to connect the
fixed wiring without difficulty after a part of the
appliance has been fixed to its support

25.4 Cable and conduit entries, rated current of

N/A
appliance not exceeding 16 A, dimension according

to table 10 (mm) .................................................... :

Introduction of conduit or cable does not reduce

N/A
clearances or creepage distances below values
specified in clause 29

25.5 Method for assembling the supply cord to the appliance: ----

- type X attachment N/A

- type Y attachment N/A

- type Z attachment, if allowed in relevant part 2 N/A
Type X attachment, other than those with a

N/A
specially prepared cord, not used for flat twin tinsel
cords

For multi-phase appliances supplied with a supply

N/A
cord and that are intended to be permanently
connected to fixed wiring, the supply cord is
assembled to the appliance by type Y attachment

25.6 Plugs fitted with only one flexible cord N/A

25.7 Supply cords, other than for class III appliances, being one of the following types: ----

- rubber sheathed (at least 60245 IEC 53) N/A

- polychloroprene sheathed (at least 60245 IEC 57) N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 38 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- cross-linked polyvinyl chloride sheathed (at least

N/A

60245 IEC 88)

- polyvinyl chloride sheathed. Not used if they are likely to touch metal parts having a
temperature rise exceeding 75 K during the test of clause 11

- light polyvinyl chloride sheathed cord

N/A
(60227 IEC 52), for appliances not exceeding
3 kg

- ordinary polyvinyl chloride sheathed cord

N/A
(60227 IEC 53), for other appliances

- heat resistant polyvinyl chloride sheathed. Not used for type X attachment other
than specially prepared cords

- heat-resistant light polyvinyl chloride sheathed

N/A
cord (60227 IEC 56), for appliances not
exceeding 3 kg

- heat-resistant polyvinyl chloride sheathed cord

N/A
(60227 IEC 57), for other appliances

Supply cords for class III appliances adequately

N/A

insulated

Test with 500 V for 2 min for supply cords of

N/A

class III appliances that contain live parts

25.8 Nominal cross-sectional area of supply cords not

N/A

less than table 11; rated current (A); cross-sectional

area (mm²) ............................................................ :

----

----

25.9 Supply cords not in contact with sharp points or

N/A

edges

25.10 Supply cord of class I appliances have a

N/A

green/yellow core for earthing

25.11 Conductors of supply cords not consolidated by

N/A

soldering where they are subject to contact
pressure, unless

the contact pressure is provided by spring terminals N/A

25.12 Insulation of the supply cord not damaged when

N/A

moulding the cord to part of the enclosure

25.13 Inlet openings so constructed as to prevent damage

P

to the supply cord

If the enclosure at the inlet opening is not of

N/A

insulating material, a non-detachable lining or
bushing complying with 29.3 for supplementary
insulation provided

If unsheathed supply cord, a similar additional

N/A

bushing or lining is required, unless the appliance is
class 0, or N/A
a class III appliance not containing live parts P

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 39 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

25.14 Supply cords moved while in operation adequately

N/A

protected against excessive flexing
Flexing test, as described: ----

- applied force (N) ................................................. : N/A

- number of flexings .............................................. : N/A

The test does not result in: ----

- short-circuit between the conductors, such that the

N/A

current exceeds a value of twice the rated current

- breakage of more than 10 % of the strands of any

N/A

conductor

- separation of the conductor from its terminal N/A

- loosening of any cord guard N/A

- damage to the cord or the cord guard N/A

- broken strands piercing the insulation and

N/A

becoming accessible

25.15 For appliances with supply cord and appliances to

N/A
be permanently connected to fixed wiring by a
flexible cord, conductors of the supply cord relieved
from strain, twisting and abrasion by use of cord
anchorage

The cord cannot be pushed into the appliance to

N/A
such an extent that the cord or internal parts of the
appliance can be damaged

Pull and torque test of supply cord, values shown in

N/A
table 12: mass (kg); pull (N); torque (not on

automatic cord reel) (Nm) ..................................... :

Cord not damaged and max. 2 mm displacement of

N/A
the cord

25.16 Cord anchorages for type X attachments constructed and located so that: ----

- replacement of the cord is easily possible N/A

- it is clear how the relief from strain and the

N/A
prevention of twisting are obtained

- they are suitable for different types of supply cord N/A

- cord cannot touch the clamping screws of cord

N/A
anchorage if these screws are accessible, unless

they are separated from accessible metal parts by

N/A
supplementary insulation

- the cord is not clamped by a metal screw which

N/A
bears directly on the cord

- at least one part of the cord anchorage securely

N/A
fixed to the appliance, unless

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 40 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

it is part of a specially prepared cord

N/A

- screws which have to be operated when replacing
the cord do not fix any other component, unless

the appliance becomes inoperative or incomplete or

the parts cannot be removed without a tool

- if labyrinths can be bypassed the test of 25.15 is
nevertheless withstood

- for class 0, 0I and I appliances they are of
insulating material or are provided with an insulating
lining, unless

failure of the insulation of the cord does not make

accessible metal parts live

- for class II appliances they are of insulating
material, or

if of metal, they are insulated from accessible metal

parts by supplementary insulation

After the test of 25.15, under the conditions

specified, the conductors have not moved by more
than 1 mm in the terminals

25.17 Adequate cord anchorages for type Y and Z
attachment, test with the cord supplied with the
appliance

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

25.18 Cord anchorages only accessible with the aid of a

N/A

tool, or

Constructed so that the cord can only be fitted with

N/A

the aid of a tool

25.19 Type X attachment, glands not used as cord

N/A

anchorage in portable appliances

Tying the cord into a knot or tying the cord with

N/A

string not used

25.20 The insulated conductors of the supply cord for

N/A
type Y and Z attachment additionally insulated from
accessible metal parts

25.21 Space for supply cord for type X attachment or for connection of fixed wiring
constructed:

- to permit checking of conductors with respect to

N/A
correct positioning and connection before fitting any
cover

- so there is no risk of damage to the conductors or

N/A
their insulation when fitting the cover

- for portable appliances, so that the uninsulated

N/A
end of a conductor, if it becomes free from the
terminal, prevented from contact with accessible
metal parts

----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 41 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

2 N test to the conductor for portable appliances; no

N/A

contact with accessible metal parts

25.22 Appliance inlets: ----

- live parts not accessible during insertion or

P
removal

Requirement not applicable to appliance inlets

N/A
complying with IEC 60320-1

- connector can be inserted without difficulty P

- the appliance is not supported by the connector P

- not for cold conditions if temp. rise of external

N/A
metal parts exceeds 75 K during clause 11, unless

the supply cord is unlikely to touch such metal parts N/A

25.23 Interconnection cords comply with the requirements

N/A
for the supply cord, except that:

- the cross-sectional area of the conductors is

N/A
determined on the basis of the maximum current
during clause 11

- the thickness of the insulation may be reduced N/A
If necessary, electric strength test of 16.3 N/A

25.24 Interconnection cords not detachable without the

N/A
aid of a tool if compliance with this standard is
impaired when they are disconnected

25.25 Dimensions of pins that are inserted into

N/A
socket-outlets compatible with the dimensions of
the relevant socket-outlet.

Dimensions of pins and engagement face in

N/A
accordance with the dimensions of the relevant plug
in IEC/TR 60083

26 TERMINALS FOR EXTERNAL CONDUCTORS ----

26.1 Appliances provided with terminals or equally

N/A
effective devices for connection of external
conductors

Terminals only accessible after removal of a

N/A
non-detachable cover, except

for class III appliances that do not contain live parts N/A
Earthing terminals may be accessible if a tool is

N/A
required to make the connections and means are
provided to clamp the wire independently from its
connection

26.2 Appliances with type X attachment and appliances

N/A
for the connection of cables to fixed wiring provided
with terminals in which connections are made by
means of screws, nuts or similar devices, unless

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 42 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

the connections are soldered

N/A

Screws and nuts not used to fix any other

N/A
component, except

internal conductors, if so arranged that they are

N/A
unlikely to be displaced when fitting the supply
conductors

If soldered connections used, the conductor so

N/A
positioned or fixed that reliance is not placed on
soldering alone, unless

barriers provided so that neither clearances nor

N/A
creepage distances between live parts and other
metal parts reduced below the values for
supplementary insulation if the conductor becomes
free at the soldered joint

26.3 Terminals for type X attachment and for connection

N/A
of cables of fixed wiring so constructed that the
conductor is clamped between metal surfaces with
sufficient contact pressure but without damaging
the conductor

Terminals fixed so that when the clamping means is tightened or loosened: ----

- the terminal does not become loose N/A

- internal wiring is not subjected to stress N/A

- neither clearances nor creepage distances are

N/A
reduced below the values in clause 29

Compliance checked by inspection and by the test

N/A
of subclause 9.6 of IEC 60999-1, the torque applied
being equal to two-thirds of the torque specified

(Nm) ...................................................................... :

No deep or sharp indentations of the conductors N/A

26.4 Terminals for type X attachment, except those

N/A
having a specially prepared cord and those for the
connection of cables of fixed wiring, no special
preparation of conductors such as by soldering, use
of cable lugs, eyelets or similar, and

so constructed or placed that conductors prevented

N/A
from slipping out when clamping screws or nuts are
tightened

26.5 Terminals for type X attachment so located or

N/A
shielded that if a wire of a stranded conductor
escapes, no risk of accidental connection to other
parts that result in a hazard

Stranded conductor test, 8 mm insulation removed N/A
No contact between live parts and accessible metal

N/A
parts and,

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 43 of 116 Report No.: 160421073GZU-003

appliances not containing live parts, accessible after

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

for class II constructions, between live parts and

N/A
metal parts separated from accessible metal parts
by supplementary insulation only

26.6 Terminals for type X attachment and for connection

N/A
of cables of fixed wiring suitable for connection of
conductors with cross-sectional area according to
table 13; rated current (A); nominal cross-sectional

area (mm²) ............................................................ :

If a specially prepared cord is used, terminals need

N/A
only be suitable for that cord

26.7 Terminals for type X attachment, except in class III

N/A
removal of a cover or part of the enclosure

26.8 Terminals for the connection of fixed wiring,

N/A
including the earthing terminal, located close to
each other

26.9 Terminals of the pillar type constructed and located

N/A
as specified

26.10 Terminals with screw clamping and screwless

N/A
terminals not used for flat twin tinsel cords, unless

conductors ends fitted with means suitable for

N/A
screw terminals

Pull test of 5 N to the connection N/A

26.11 For type Y and Z attachment, soldered, welded,

N/A
crimped or similar connections may be used

For class II appliances, the conductor so positioned

N/A
or fixed that reliance is not placed on soldering,
welding or crimping alone

If soldering, welding or crimping alone used,

N/A
barriers provided so that clearances and creepage
distances between live parts and other metal parts
are not reduced below the values for supplementary
insulation if the conductor becomes free

27 PROVISION FOR EARTHING ----

27.1 Accessible metal parts of class 0I and I appliances

N/A
permanently and reliably connected to an earthing
terminal or earthing contact of the appliance inlet

Earthing terminals and earthing contacts not

N/A
connected to the neutral terminal

Class 0, II and III appliances have no provision for

P
earthing

Safety extra-low voltage circuits not earthed, unless P
protective extra-low voltage circuits N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 44 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

27.2 Clamping means of earthing terminals adequately

N/A

secured against accidental loosening

Terminals for the connection of external

equipotential bonding conductors allow connection
of conductors of 2,5 to 6 mm², and

do not provide earthing continuity between different

parts of the appliance, and

conductors cannot be loosened without the aid of a

tool

27.3 For a detachable part having an earth connection
and being plugged into another part of the
appliance, the earth connection is made before and
separated after current-carrying connections when
removing the part

For appliances with supply cords, current-carrying

conductors become taut before earthing conductor,
if the cord slips out of the cord anchorage

27.4 No risk of corrosion resulting from contact between
parts of the earthing terminal and the copper of the
earthing conductor or other metal

Parts providing earthing continuity, other than parts

of a metal frame or enclosure, have adequate
resistance to corrosion

If of steel, these parts provided with an

electroplated coating with a thickness at least 5 µm

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Adequate protection against rusting of parts of

N/A
coated or uncoated steel, only intended to provide
or transmit contact pressure

In the body of the earthing terminal is a part of a

N/A
frame or enclosure of aluminium or aluminium
alloys, precautions taken to avoid risk of corrosion

27.5 Low resistance of connection between earthing

N/A
terminal and earthed metal parts

This requirement does not apply to connections

N/A
providing earthing continuity in the protective
extra-low voltage circuit, provided the clearances of
basic insulation are based on the rated voltage of
the appliance

Resistance not exceeding 0,1 at the specified 

N/A

low-resistance test ( ) ........................................ :

27.6 The printed conductors of printed circuit boards not

N/A
used to provide earthing continuity in hand-held
appliances.

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 45 of 116 Report No.: 160421073GZU-003

mm

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

They may be used to provide earthing continuity in

N/A
other appliances if at least two tracks are used with
independent soldering points and the appliance
complies with 27.5 for each circuit

28 SCREWS AND CONNECTIONS ----

28.1 Fixings, electrical connections and connections
providing earthing continuity withstand mechanical
stresses

Screws not of soft metal liable to creep, such as

zinc or aluminium

Diameter of screws of insulating material min. 3
Screws of insulating material not used for any

electrical connections or connections providing
earthing continuity

Screws used for electrical connections or

connections providing earthing continuity screwed
into metal

Screws not of insulating material if their

replacement by a metal screw can impair
supplementary or reinforced insulation

For type X attachment, screws to be removed for

replacement of supply cord or for user
maintenance, not of insulating material if their
replacement by a metal screw impairs basic
insulation

For screws and nuts; torque-test as specified in

table 14 ................................................................. :

P

P

N/A
N/A

N/A

N/A

N/A

(see appended table) N/A

28.2 Electrical connections and connections providing

N/A
earthing continuity constructed so that contact
pressure is not transmitted through non-ceramic
insulating material liable to shrink or distort, unless

there is resiliency in the metallic parts to

N/A
compensate for shrinkage or distortion of the
insulating material

This requirement does not apply to electrical connections in circuits of appliances

----

for which:

- 30.2.2 is applicable and that carry a current not

N/A

exceeding 0,5 A

- 30.2.3 is applicable and that carry a current not

N/A

exceeding 0,2 A

28.3 Space-threaded (sheet metal) screws only used for

N/A
electrical connections if they clamp the parts
together

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 46 of 116 Report No.: 160421073GZU-003

Clearances, creepage distances and solid insulation

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Thread-cutting (self-tapping) screws and thread

N/A
rolling screws only used for electrical connections if
they generate a full form standard machine screw
thread

Thread-cutting (self-tapping) screws not used if they

N/A

are likely to be operated by the user or installer

Thread-cutting, thread rolling and space threaded screws may be used in

---­connections providing earthing continuity provided it is not necessary to disturb the
connection:

- in normal use, N/A

- during user maintenance, N/A

- when replacing a supply cord having a type X

N/A

attachment, or

- during installation N/A
At least two screws being used for each connection

N/A

providing earthing continuity, unless

the screw forms a thread having a length of at least

N/A

half the diameter of the screw

28.4 Screws and nuts that make mechanical connection

N/A
secured against loosening if they also make
electrical connections or connections providing
earthing continuity

This requirement does not apply to screws in the

N/A
earthing circuit if at least two screws are used, or

if an alternative earthing circuit is provided N/A
Rivets for electrical connections or connections

N/A
providing earthing continuity secured against
loosening if the connections are subjected to torsion

29 CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION ----

P
withstand electrical stress

For coatings used on printed circuits boards to

N/A
protect the microenvironment (Type 1) or to provide

basic insulation (Type 2), annex J applies ............ :

The microenvironment is pollution degree 1 under

N/A
type 1 protection

For type 2 protection, the spacing between the

N/A
conductors before the protection is applied is not
less than the values specified in Table 1 of
IEC 60664-3

These values apply to functional, basic,

N/A

supplementary and reinforced insulation .............. :

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 47 of 116 Report No.: 160421073GZU-003

those specified for basic insulation in table 16, using

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

29.1 Clearances not less than the values specified in

(see appended table)

P
table 16, taking into account the rated impulse
voltage for the overvoltage categories of table 15,

unless .................................................................... :

for basic insulation and functional insulation they

N/A

comply with the impulse voltage test of clause 14

However, if the distances are affected by wear,

P
distortion, movement of the parts or during
assembly, the clearances for rated impulse voltages
of 1500 V and above are increased by 0,5 mm and
the impulse voltage test is not applicable

Impulse voltage test is not applicable: ----

- when the microenvironment is pollution degree 3,

N/A
or

- for basic insulation of class 0 and class 01

N/A
appliances

Appliances are in overvoltage category II P
A force of 2 N is applied to bare conductors, other

P
than heating elements

A force of 30 N is applied to accessible surfaces P

29.1.1 Clearances of basic insulation withstand the

N/A
overvoltages, taking into account the rated impulse
voltage

The values of table 16 or the impulse voltage test of

(see appended table) N/A

clause 14 are applicable ....................................... :

Clearance at the terminals of tubular sheathed

N/A
heating elements may be reduced to 1,0 mm if the
microenvironment is pollution degree 1

Lacquered conductors of windings considered to be

N/A
bare conductors

29.1.2 Clearances of supplementary insulation not less

(see appended table) N/A
than those specified for basic insulation in table 16

.............................................................................. :

29.1.3 Clearances of reinforced insulation not less than

(see appended table) N/A

the next higher step for rated impulse voltage ...... :

For double insulation, with no intermediate

N/A
conductive part between basic and supplementary
insulation, clearances are measured between live
parts and the accessible surface, and the insulation
system is treated as reinforced insulation

29.1.4 Clearances for functional insulation are the largest values determined from: ----

- table 16 based on the rated impulse voltage ...... : (see appended table) P

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 48 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- table F.7a in IEC 60664-1, frequency not

N/A

exceeding 30 kHz

- clause 4 of IEC 60664-4, frequency exceeding

N/A
30 kHz

If values of table 16 are largest, the impulse voltage

N/A
test of clause 14 may be applied instead, unless

the microenvironment is pollution degree 3, or N/A
the distances can be affected by wear, distortion,

N/A
movement of the parts or during assembly

However, clearances are not specified if the

P
appliance complies with clause 19 with the
functional insulation short-circuited

Lacquered conductors of windings considered to be

P
bare conductors

However, clearances at crossover points are not

P
measured

Clearance between surfaces of PTC heating

N/A
elements may be reduced to 1mm

29.1.5 Appliances having higher working voltages than rated voltage, clearances for basic

----

insulation are the largest values determined from:

- table 16 based on the rated impulse voltage ...... : N/A

- table F.7a in IEC 60664-1, frequency not

N/A
exceeding 30 kHz

- clause 4 of IEC 60664-4, frequency exceeding

N/A
30 kHz

If clearances for basic insulation are selected from

N/A
Table F.7a of IEC 60664-1 or clause 4 of
IEC 60664-4, the clearances of supplementary
insulation are not less than those specified for basic
insulation

If clearances for basic insulation are selected from

N/A
Table F.7a of IEC 60664-1, the clearances of
reinforced insulation dimensioned as specified in
Table F.7a are to withstand 160% of the withstand
voltage required for basic insulation

If clearances for basic insulation are selected from

N/A
clause 4 of IEC 60664-4, the clearances of
reinforced insulation are twice the value required for
basic insulation

If the secondary winding of a step-down transformer

N/A
is earthed, or if there is an earthed screen between
the primary and secondary windings, clearances of
basic insulation on the secondary side not less than
those specified in table 16, but using the next lower
step for rated impulse voltage

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 49 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Circuits supplied with a voltage lower than rated

N/A
voltage, clearances of functional insulation are
based on the working voltage used as the rated
voltage in table 15

29.2 Creepage distances not less than those appropriate

(see appended table) N/A
for the working voltage, taking into account the

material group and the pollution degree ............... :

Pollution degree 2 applies, unless N/A

- precautions taken to protect the insulation;

N/A
pollution degree 1

- insulation subjected to conductive pollution;

N/A
pollution degree 3

Electrode-type appliances, the microenvironment of

N/A
the insulation supporting the electrodes is
pollution degree 3 (IEC 60335-2-98)

A force of 2 N is applied to bare conductors, other

N/A
than heating elements

A force of 30 N is applied to accessible surfaces N/A
In a double insulation system, the working voltage

N/A
for both the basic and supplementary insulation is
taken as the working voltage across the complete
double insulation system

29.2.1 Creepage distances of basic insulation not less

(see appended table) N/A

than specified in table 17 ...................................... :

However, if the working voltage is periodic and has

N/A
a frequency exceeding 30 kHz, the creepage
distances are also determined from table 2 of
IEC 60664-4, these values being used if exceeding

the values in table 17 ............................................ :

Except for pollution degree 1, corresponding

N/A
creepage distance not less than the minimum
specified for the clearance in table 16, if the
clearance has been checked according to the test

of clause 14 ........................................................... :

29.2.2 Creepage distances of supplementary insulation at

(see appended table) N/A
least those specified for basic insulation in table 17,

or ........................................................................... :

Table 2 of IEC 60664-4, as applicable .................. : N/A

29.2.3 Creepage distances of reinforced insulation at least

(see appended table) N/A
double those specified for basic insulation in table

17, or ..................................................................... :

Table 2 of IEC 60664-4, as applicable .................. : N/A

29.2.4 Creepage distances of functional insulation not less

(see appended table) N/A

than specified in table 18 ...................................... :

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 50 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

However, if the working voltage is periodic and has

N/A
a frequency exceeding 30 kHz, the creepage
distances are also determined from table 2 of
IEC 60664-4, these values being used if exceeding

the values in table 18 ............................................ :

Creepage distances may be reduced if the

N/A
appliance complies with clause 19 with the
functional insulation short-circuited

29.3 Supplementary and reinforced insulation have

N/A
adequate thickness, or a sufficient number of
layers, to withstand the electrical stresses

Compliance checked: ----

- by measurement, in accordance with 29.3.1, or N/A

- by an electric strength test in accordance with

N/A

29.3.2, or

- by an assessment of the thermal quality of the

N/A
material combined with an electric strength test, in
accordance with 29.3.3, and

for accessible parts of reinforced insulation

N/A
consisting of a single layer, by measurement in
accordance with 29.3.4, or

- as specified in subclause 6.3 of IEC 60664-4 for

N/A
insulation that is subjected to any periodic voltage
having a frequency exceeding 30 kHz

29.3.1 Supplementary insulation have a thickness of at

N/A
least 1 mm

Reinforced insulation have a thickness of at least

N/A
2 mm

29.3.2 Each layer of material withstand the electric

N/A
strength test of 16.3 for supplementary insulation

Supplementary insulation consist of at least 2 layers N/A
Reinforced insulation consist of at least 3 layers N/A

29.3.3 The insulation is subjected to the dry heat test Bb of

N/A
IEC 60068-2-2, followed by

the electric strength test of 16.3 N/A
If the temperature rise during the tests of clause 19

N/A
does not exceed the value specified in table 3, the
test of IEC 60068-2-2 is not carried out

29.3.4 Thickness of accessible parts of reinforced

N/A
insulation consisting of a single layer not less than

specified in table 19 .............................................. :

30 RESISTANCE TO HEAT AND FIRE ----

30.1 External parts of non-metallic material, P

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 51 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

parts supporting live parts, and

N/A

parts of thermoplastic material providing

N/A
supplementary or reinforced insulation

sufficiently resistant to heat N/A
Ball-pressure test according to IEC 60695-10-2 P
External parts tested at 40 °C plus the maximum

(see appended table) P
temperature rise determined during the test of
clause 11, or at 75 °C, whichever is the higher;

temperature (°C) ................................................... :

Parts supporting live parts tested at 40 °C plus the

(see appended table) P
maximum temperature rise determined during the
test of clause 11, or at 125 °C, whichever is the

higher; temperature (°C) ....................................... :

Parts of thermoplastic material providing

(see appended table) N/A
supplementary or reinforced insulation tested at
25 °C plus the maximum temperature rise
determined during clause 19, if higher; temperature

(°C) ........................................................................ :

30.2 Parts of non-metallic material resistant to ignition

P
and spread of fire

This requirement does not apply to: ---­ parts having a mass not exceeding 0,5 g, provided

N/A
the cumulative effect is unlikely to propagate flames
that originate inside the appliance by propagating
flames from one part to another, or

decorative trims, knobs and other parts unlikely to

N/A
be ignited or to propagate flames that originate
inside the appliance

Compliance checked by the test of 30.2.1, and in

----

addition:

- for attended appliances, 30.2.2 applies N/A

- for unattended appliances, 30.2.3 applies P
For appliances for remote operation, 30.2.3 applies N/A
For base material of printed circuit boards, 30.2.4

P
applies

30.2.1 Parts of non-metallic material subjected to the

P
glow-wire test of IEC 60695-2-11 at 550 °C

However, test not carried out if the material is

N/A
classified as having a glow-wire flammability index
according to IEC 60695-2-12 of at least 550 °C, or

the material is classified at least HB40 according to

N/A
IEC 60695-11-10

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 52 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Parts for which the glow-wire test cannot be carried

N/A
out need to meet the requirements in ISO 9772 for
material classified HBF

30.2.3 Appliances operated while unattended, tested as
specified in 30.2.3.1 and 30.2.3.2

The tests are not applicable to conditions as

specified ................................................................ :

30.2.3.1 Parts of non-metallic material supporting
connections carrying a current exceeding 0,2 A
during normal operation, and

parts of non-metallic material, other than small

parts, within a distance of 3 mm,

subjected to the glow-wire test of IEC 60695-2-11

with a test severity of 850 °C

Glow-wire applied to an interposed shielding

material, if relevant

The glow-wire test is not carried out on parts of

material classified as having a glow-wire
flammability index according to IEC 60695-2-12 of
at least 850 °C

30.2.3.2 Parts of non-metallic material supporting
connections, and

parts of non-metallic material within a distance of

3 mm,

P

N/A

P

P

P

N/A

N/A

P

P

subjected to glow-wire test of IEC 60695-2-11 P
The test severity is: ----

- 750 °C, for connections carrying a current

P

exceeding 0,2 A during normal operation

- 650 °C, for other connections N/A

Glow-wire applied to an interposed shielding

N/A

material, if relevant

However, the glow-wire test of 750 °C or 650 °C as appropriate, is not carried out on

----

parts of material fulfilling both or either of the following classifications:

- a glow-wire ignition temperature according to

N/A

IEC 60695-2-13 of at least:

- 775 °C, for connections carrying a current

N/A

exceeding 0,2 A during normal operation

- 675 °C, for other connections N/A

- a glow-wire flammability index according to

N/A

IEC 60695-2-12 of at least:

- 750 °C, for connections carrying a current

N/A

exceeding 0,2 A during normal operation

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 53 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- 650 °C, for other connections

N/A

The glow-wire test is also not carried out on small parts. These parts are to: ----

- comprise material having a glow-wire ignition

N/A
temperature of at least 775 °C or 675 °C as
appropriate, or

- comprise material having a glow-wire flammability

N/A
index of at least 750 °C or 650 °C as appropriate, or

- comply with the needle-flame test of annex E, or N/A

- comprise material classified as V-0 or V-1

N/A
according to IEC 60695-11-10

The consequential needle-flame test of annex E applied to non-metallic parts that

---­encroach within the vertical cylinder placed above the centre of the connection zone
and on top of the non-metallic parts supporting current-carrying connections, and
parts of non-metallic material within a distance of 3 mm of such connections if these
parts are those:

- parts that withstood the glow-wire test of

P
IEC 60695-2-11 of 750 °C or 650 °C as appropriate,
but produce a flame that persist longer than 2 s, or

- parts that comprised material having a glow-wire

N/A
flammability index of at least 750 °C or 650 °C as
appropriate, or

- small parts, that comprised material having a

N/A
glow-wire flammability index of at least 750 °C or
650 °C as appropriate, or

- small parts for which the needle-flame test of

N/A
annex E was applied, or

- small parts for which a material classification of

N/A
V-0 or V-1 was applied

However, the consequential needle-flame test is not carried out on non-metallic

----

parts, including small parts, within the cylinder that are:

- parts having a glow-wire ignition temperature of at

N/A
least 775 °C or 675 °C as appropriate, or

- parts comprising material classified as V-0 or V-1

N/A
according to IEC 60695-11-10, or

- parts shielded by a flame barrier that meets the

N/A
needle-flame test of annex E or that comprises
material classified as V-0 or V-1 according to
IEC 60695-11-10

30.2.4 Base material of printed circuit boards subjected to

P
the needle-flame test of annex E

Test not applicable to conditions as specified ...... : N/A

31 RESISTANCE TO RUSTING ----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 54 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Relevant ferrous parts adequately protected against

P

rusting

Tests specified in part 2 when necessary N/A
32 RADIATION, TOXICITY AND SIMILAR HAZARDS ---­ Appliance does not emit harmful radiation or

P
present a toxic or similar hazard due to their
operation in normal use

Compliance is checked by the limits or tests

P
specified in part 2, if relevant

A ANNEX A (INFORMATIVE)

----

ROUTINE TESTS

Description of routine tests to be carried out by the

N/A
manufacturer

B ANNEX B (NORMATIVE)

----

APPLIANCES POWERED BY RECHARGEABLE BATTERIES

The following modifications to this standard are

N/A
applicable for appliances powered by batteries that
are recharged in the appliance

This annex does not apply to battery chargers N/A

3.1.9 Appliance operated under the following conditions: ----

- the appliance, supplied by its fully charged battery,

N/A
operated as specified in relevant part 2

- the battery is charged, the battery being initially

N/A
discharged to such an extent that the appliance
cannot operate

- f possible, the appliance is supplied from the

N/A
supply mains through its battery charger, the battery
being initially discharged to such an extent that the
appliance cannot operate. The appliance is
operated as specified in relevant part 2

- if the appliance incorporates inductive coupling

N/A
between two parts that are detachable from each
other, the appliance is supplied from the supply
mains with the detachable part removed

3.6.2 Part to be removed in order to discard the battery is

N/A
not considered to be detachable

5.B.101 Appliances supplied from the supply mains tested

N/A
as specified for motor-operated appliances

7.1 Battery compartment for batteries intended to be

N/A
replaced by the user, marked with battery voltage
and polarity of the terminals

The positive terminal indicated by symbol

N/A
IEC 60417-5005 and the negative terminal by
symbol IEC 60417-5006

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 55 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

7.6 Symbols 60417-5005 and IEC 60417-5006

N/A

7.12 The instructions give information regarding charging N/A
The instructions for appliances incorporating

N/A
batteries intended to be replaced by the user
includes required information

Details about how to remove batteries containing

N/A
materials hazardous to the environment given

7.15 Markings placed on the part of the appliance

N/A
connected to the supply mains

8.2 Appliances having batteries that according to the

N/A
instruction may be replaced by the user need only
have basic insulation between live parts and the
inner surface of the battery compartment

If the appliance can be operated without batteries,

N/A
double or reinforced insulation required

11.7 The battery is charged for the period stated in the

N/A

instructions or 24 h ................................................ :

19.1 Appliances subjected to tests of 19.B.101, 19.B.102

N/A
and 19.B.103

19.10 Not applicable N/A

19.B.101 Appliances supplied at rated voltage for 168 h, the

N/A
battery being continually charged

19.B.102 For appliances having batteries that can be

N/A
removed without the aid of a tool, short-circuit of the
terminals of the battery, the battery being fully
charged,

19.B.103 Appliances having batteries replaceable by the user

N/A
supplied at rated voltage under normal operation
with the battery removed or in any position allowed
by the construction

21.B.101 Appliances having pins for insertion into

N/A
socket-outlets have adequate mechanical strength

Part of the appliance incorporating the pins subjected to the free fall test, procedure

----

2, of IEC 60068-2-31, the number of falls being:

- 100, if the mass of the part does not exceed 250 g

N/A

(g) .......................................................................... :

- 50, if the mass of the part exceeds 250 g ........... : N/A

After the test, the requirements of 8.1, 15.1.1, 16.3

N/A
and clause 29 are met

22.3 Appliances having pins for insertion into

N/A
socket-outlets tested as fully assembled as possible

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 56 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

25.13 An additional lining or bushing not required for

N/A
interconnection cords in class III appliances or
class III constructions operating at safety extra-low
voltage not containing live parts

30.2 For parts of the appliance connected to the supply

N/A

mains during the charging period, 30.2.3 applies

For other parts, 30.2.2 applies N/A
C ANNEX C (NORMATIVE)

----

AGEING TEST ON MOTORS

Tests, as described, carried out when doubt with

N/A
regard to the temperature classification of the
insulation of a motor winding

Test conditions as specified N/A
D ANNEX D (NORMATIVE)

----

THERMAL MOTOR PROTECTORS

Applicable to appliances having motors that

N/A
incorporate thermal motor protectors necessary for
compliance with the standard

Test conditions as specified N/A
E ANNEX E (NORMATIVE)

----

NEEDLE-FLAME TEST

Needle-flame test carried out in accordance with IEC 60695-11-5, with the following

----

modifications:

7 Severities ---­ The duration of application of the test flame is

P
30 s ± 1 s

9 Test procedure ----

9.1 The specimen so arranged that the flame can be

P
applied to a vertical or horizontal edge as shown in
the examples of figure 1

9.2 The first paragraph does not apply N/A
If possible, the flame is applied at least 10 mm from

P
a corner

9.3 The test is carried out on one specimen P
If the specimen does not withstand the test, the test

N/A
may be repeated on two additional specimens, both
withstanding the test

11 Evaluation of test results ---­ The duration of burning not exceeding 30 s P
However, for printed circuit boards, the duration of

P
burning not exceeding 15 s

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 57 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

F ANNEX F (NORMATIVE)

----

CAPACITORS

Capacitors likely to be permanently subjected to the supply voltage, and used for

N/A
radio interference suppression or voltage dividing, comply with the following clauses
of IEC 60384-14, with the following modifications:

1.5 Terms and definitions ----

1.5.3 Class X capacitors tested according to subclass X2 N/A

1.5.4 This subclause is applicable N/A

1.6 Marking ---­ Items a) and b) are applicable N/A

3.4 Approval testing ----

3.4.3.2 Table 3 is applicable as described N/A

4.1 Visual examination and check of dimensions ---­ This subclause is applicable N/A

4.2 Electrical tests ----

4.2.1 This subclause is applicable N/A

4.2.5 This subclause is applicable N/A

4.2.5.2 Only table 11 is applicable N/A
Values for test A apply N/A
However, for capacitors in heating appliances the

N/A

values for test B or C apply

4.12 Damp heat, steady state ---­ This subclause is applicable N/A
Only insulation resistance and voltage proof are

N/A

checked

4.13 Impulse voltage ---­ This subclause is applicable N/A

4.14 Endurance ---­ Subclauses 4.14.1, 4.14.3, 4.14.4 and 4.14.7 are

N/A

applicable

4.14.7 Only insulation resistance and voltage proof are

N/A

checked

No visible damage N/A

4.17 Passive flammability test ---­ This subclause is applicable N/A

4.18 Active flammability test ---­ This subclause is applicable N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 58 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

G ANNEX G (NORMATIVE)

----

SAFETY ISOLATING TRANSFORMERS

The following modifications to this standard are applicable for safety isolating

----

transformers:

7 Marking and instructions ----

7.1 Transformers for specific use marked with: ----

- ame, trademark or identification mark of the

N/A

manufacturer or responsible vendor ..................... :

- model or type reference ...................................... : N/A

17 Overload protection of transformers and associated circuits ---­ Fail-safe transformers comply with subclause 15.5

N/A

of IEC 61558-1

22 Construction ---­ Subclauses 19.1 and 19.1.2 of IEC 61558-2-6 are

N/A

applicable

29 Clearances, creepage distances and solid insulation ----

29.1, 29.2,

29.3
For insulated winding wires complying with

The distances specified in items 2a, 2c and 3 in
table 13 of IEC 61558-1 apply

N/A

N/A
subclause 19.12.3 of IEC 61558-1 there are no
requirements for clearances or creepage distances

For windings providing reinforced insulation, the

N/A
distance specified in item 2c of table 13 of
IEC 61558-1 is not assessed

For safety isolating transformers subjected to

N/A
periodic voltages with a frequency exceeding
30 kHz, the clearances, creepage distances and
solid insulation values specified in IEC 60664-4 are
applicable, if greater than the values specified in
items 2a, 2c and 3 in table 13 of IEC 61558-1

H ANNEX H (NORMATIVE)

----

SWITCHES

Switches comply with the following clauses of IEC 61058-1, as modified below: ---­ The tests of IEC 61058-1 carried out under the

N/A
conditions occurring in the appliance

Before being tested, switches are operated 20

N/A
times without load

8 Marking and documentation ---­ Switches are not required to be marked N/A
However, a switch that can be tested separately

N/A
from the appliance marked with the manufacturer’s
name or trade mark and the type reference

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 59 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

13 Mechanism

---­ The tests may be carried out on a separate sample N/A
15 Insulation resistance and dielectric strength ----

15.1 Not applicable N/A

15.2 Not applicable N/A

15.3 Applicable for full disconnection and

N/A

micro-disconnection
17 Endurance ---­ Compliance is checked on three separate

N/A

appliances or switches
For 17.2.4.4, the number of cycles declared

N/A

according to 7.1.4 is 10 000, unless
otherwise specified in 24.1.3 of the relevant part 2

N/A

of IEC 60335 ......................................................... :

Switches for operation under no load and which can

N/A

be operated only by a tool, and
switches operated by hand that are interlocked so

N/A

that they cannot be operated under load,
are not subjected to the tests N/A
However, switches without this interlock are

N/A
subjected to the test of 17.2.4.4 for 100 cycles of
operation

Subclauses 17.2.2 and 17.2.5.2 not applicable N/A
The ambient temperature during the test is that

N/A
occurring in the appliance during the test of
clause 11 in IEC 60335-1

The temperature rise of the terminals not more than

N/A
30 K above the temperature rise measured in

clause 11 of IEC 60335-1 (K)................................ :

20 Clearances, creepage distances, solid insulation and coatings of rigid printed board

----

assemblies

This clause is applicable to clearances and

N/A
creepage distances for functional insulation, across
full disconnection and micro-disconnection, as
stated in table 24

I ANNEX I (NORMATIVE)

---­MOTORS HAVING BASIC INSULATION THAT IS INADEQUATE FOR THE
RATED VOLTAGE OF THE APPLIANCE

The following modifications to this standard are applicable for motors having basic

---­insulation that is inadequate for the rated voltage of the appliance:

8 Protection against access to live parts ----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 60 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

8.1 Metal parts of the motor are considered to be bare

N/A

live parts

11 Heating ----

11.3 The temperature rise of the body of the motor is

N/A
determined instead of the temperature rise of the
windings

11.8 The temperature rise of the body of the motor,

N/A
where in contact with insulating material, not
exceeding values in table 3 for the relevant
insulating material

16 Leakage current and electric strength ----

16.3 Insulation between live parts of the motor and its

N/A
other metal parts is not subjected to the test

19 Abnormal operation ----

19.1 The tests of 19.7 to 19.9 are not carried out N/A

19.I.101 Appliance operated at rated voltage with each of the following fault conditions: ----

- short circuit of the terminals of the motor, including

N/A
any capacitor incorporated in the motor circuit

- short circuit of each diode of the rectifier N/A

- open circuit of the supply to the motor N/A

- open circuit of any parallel resistor, the motor

N/A
being in operation

Only one fault simulated at a time, the tests carried

N/A
out consecutively

22 Construction ----

22.I.101 For class I appliances incorporating a motor

N/A
supplied by a rectifier circuit, the d.c. circuit being
insulated from accessible parts of the appliance by
double or reinforced insulation

Compliance checked by the tests specified for

N/A
double and reinforced insulation

J ANNEX J (NORMATIVE)

----

COATED PRINTED CIRCUIT BOARDS

Testing of protective coatings of printed circuit boards carried out in accordance with

----

IEC 60664-3 with the following modifications:

5.7 Conditioning of the test specimens ---­ When production samples are used, three samples

N/A
of the printed circuit board are tested

5.7.1 Cold ---­ The test is carried out at -25 °C N/A

5.7.3 Rapid change of temperature ----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 61 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Severity 1 is specified

N/A

5.9 Additional tests ---­ This subclause is not applicable N/A
K ANNEX K (NORMATIVE)

OVERVOLTAGE CATEGORIES

The information on overvoltage categories is

extracted from IEC 60664-1

Overvoltage category is a numeral defining a

transient overvoltage condition

Equipment of overvoltage category IV is for use at

the origin of the installation

Equipment of overvoltage category III is equipment

in fixed installations and for cases where the
reliability and the availability of the equipment is
subject to special requirements

Equipment of overvoltage category II is energy

consuming equipment to be supplied from the fixed
installation

If such equipment is subjected to special

requirements with regard to reliability and
availability, overvoltage category III applies

Equipment of overvoltage category I is equipment

for connection to circuits in which measures are
taken to limit transient overvoltages to an
appropriate low level

----

P

P

N/A

N/A

P

N/A

N/A

L ANNEX L (INFORMATIVE)

---­GUIDANCE FOR THE MEASUREMENT OF CLEARANCES AND CREEPAGE
DISTANCES

Information for the determination of clearances and

N/A

creepage distances

M ANNEX M (NORMATIVE)

---­POLLUTION DEGREE

The information on pollution degrees is extracted

P

from IEC 60664-1

Pollution ---­ The microenvironment determines the effect of

P
pollution on the insulation, taking into account the
macroenvironment

Means may be provided to reduce pollution at the

P
insulation by effective enclosures or similar

Minimum clearances specified where pollution may

P
be present in the microenvironment

Degrees of pollution in the microenvironment ----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 62 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

For evaluating creepage distances, the following degrees of pollution in the

----

microenvironment are established:

- pollution degree 1: no pollution or only dry,

N/A
non-conductive pollution occurs. The pollution has
no influence

- pollution degree 2: only non-conductive pollution

N/A
occurs, except that occasionally a temporary
conductivity caused by condensation is to be
expected

- pollution degree 3: conductive pollution occurs or

P
dry non-conductive pollution occurs that becomes
conductive due to condensation that is to be
expected

- pollution degree 4: the pollution generates

N/A
persistent conductivity caused by conductive dust or
by rain or snow

N ANNEX N (NORMATIVE)

----

PROOF TRACKING TEST

The proof tracking test is carried out in accordance with IEC 60112 with the

----

following modifications:

7 Test apparatus ----

7.3 Test solutions ---­ Test solution A is used N/A
10 Determination of proof tracking index (PTI) ----

10.1 Procedure ---­ The proof voltage is 100 V, 175 V, 400 V or 600 V

N/A

.............................................................................. :

The test is carried out on five specimens N/A
In case of doubt, additional test with proof voltage

N/A
reduced by 25 V, the number of drops increased to
100

10.2 Report ---­ The report states if the PTI value was based on a

N/A
test using 100 drops with a test voltage of (PTI-25)
V

O ANNEX O (INFORMATIVE)

----

SELECTION AND SEQUENCE OF THE TESTS OF clause 30

Description of tests for determination of resistance

P
to heat and fire

P ANNEX P (INFORMATIVE)

---­GUIDANCE FOR THE APPLICATION OF THIS STANDARD TO APPLIANCES
USED IN WARM DAMP EQUABLE CLIMATES

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 63 of 116 Report No.: 160421073GZU-003

considered to be suitable for use in countries having

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Modifications applicable for class 0 and 01 appliances having a rated voltage

---­exceeding 150 V, intended to be used in countries having a warm damp equable
climate and that are marked WDaE

Modifications may also be applied to class 1 appliances having a rated voltage

---­exceeding 150 V, intended to be used in countries having a warm damp equable
climate and that are marked WDaE, if liable to be connected to a supply mains that
excludes the protective earthing conductor

5.7 The ambient temperature for the tests of clauses 11

N/A

and 13 is 40 +3/0 °C

7.1 The appliance marked with the letters WDaE N/A

7.12 The instructions state that the appliance is to be

N/A
supplied through a residual current device (RCD)
having a rated residual operating current not
exceeding 30 mA

The instructions state that the appliance is

N/A
a warm damp equable climate, but may also be

used in other countries

11.8 The values of Table 3 are reduced by 15 K N/A

13.2 The leakage current for class I appliances not

N/A
exceeding 0,5 mA

15.3 The value of t is 37 °C N/A

16.2 The leakage current for class I appliances not

N/A
exceeding 0,5 mA (mA):

19.13 The leakage current test of 16.2 is applied in

N/A
addition to the electric strength test of 16.3

Q ANNEX Q (INFORMATIVE)

----

SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS

Description of tests for appliances incorporating electronic circuits N/A
R ANNEX R (NORMATIVE)

----

SOFTWARE EVALUATION

Programmable electronic circuits requiring software

N/A
incorporating measures to control the fault/error
conditions specified in table R.1 or R.2 validated in
accordance with the requirements of this annex

R.1 Programmable electronic circuits using software ---­ Programmable electronic circuits requiring software

N/A
incorporating measures to control the fault/error
conditions specified in table R.1 or R.2 constructed
so that the software does not impair compliance
with the requirements of this standard

R.2 Requirements for the architecture ----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 64 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Programmable electronic circuits requiring software

N/A
incorporating measures to control the fault/error
conditions specified in table R.1 or R.2 use
measures to control and avoid software-related
faults/errors in safety-related data and
safety-related segments of the software

R.2.1.1 Programmable electronic circuits requiring software incorporating measures to

---­control the fault/error conditions specified in table R.2 have one of the following
structures:

- single channel with periodic self-test and

N/A

monitoring

- dual channel (homogenous) with comparison N/A

- dual channel (diverse) with comparison N/A
Programmable electronic circuits requiring software incorporating measures to

---­control the fault/error conditions specified in table R.1 have one of the following
structures:

- single channel with functional test N/A

- single channel with periodic self-test N/A

- dual channel without comparison N/A
R.2.2 Measures to control faults/errors ---­R.2.2.1 When redundant memory with comparison is

N/A
provided on two areas of the same component, the
data in one area is stored in a different format from
that in the other area

R.2.2.2 Programmable electronic circuits with functions

N/A
requiring software incorporating measures to
control the fault/error conditions specified in table
R.2 and that use dual channel structures with
comparison, have additional fault/error detection
means for any fault/errors not detected by the
comparison

R.2.2.3 For programmable electronic circuits with functions

N/A
requiring software incorporating measures to
control the fault/error conditions specified in table
R.1 or R.2, means are provided for the recognition
and control of errors in transmissions to external
safety-related data paths

R.2.2.4 For programmable electronic circuits with functions

N/A
requiring software incorporating measures to
control the fault/error conditions specified in table
R.1 or R.2, the programmable electronic circuits
incorporate measures to address the fault/errors in
safety-related segments and data indicated in table
R.1 and R.2 as appropriate

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 65 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

R.2.2.5 For programmable electronic circuits with functions

N/A
requiring software incorporating measures to
control the fault/error conditions specified in table
R.1 or R.2, detection of a fault/error occur before
compliance with clause 19 is impaired

R.2.2.6 The software is referenced to relevant parts of the

N/A
operating sequence and the associated hardware
functions

R.2.2.7 Labels used for memory locations are unique N/A
R.2.2.8 The software is protected from user alteration of

N/A
safety-related segments and data

R.2.2.9 Software and safety-related hardware under its

N/A
control is initialized and terminates before
compliance with clause 19 is impaired

R.3 Measures to avoid errors ---­R.3.1 General ---­ For programmable electronic circuits with functions requiring software incorporating

---­measures to control the fault/error conditions specified in table R.1 or R.2, the
following measures to avoid systematic fault in the software are applied

Software that incorporates measures used to

N/A
control the fault/error conditions specified in table
R.2 is inherently acceptable for software required to
control the fault/error conditions specified in table
R.1

R.3.2 Specification ---­R.3.2.1 Software safety requirements: Software Id: N/A
The specification of the software safety

N/A
requirements includes the descriptions listed

R.3.2.2 Software architecture ---­R.3.2.2.1 The specification of the software architecture

Document ref. No: N/A
includes the aspects listed

- techniques and measures to control software
faults/errors (refer to R.2.2);

- interactions between hardware and software;

- partitioning into modules and their allocation to the
specified safety functions;

- hierarchy and call structure of the modules (control
flow);

- interrupt handling;

- data flow and restrictions on data access;

- architecture and storage of data;

- time-based dependencies of sequences and data

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 66 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

R.3.2.2.2 The architecture specification is validated against

N/A
the specification of the software safety
requirements by static analysis

R.3.2.3 Module design and coding ---­R.3.2.3.1 Based on the architecture design, software is

N/A

suitably refined into modules

Software module design and coding is implemented

N/A
in a way that is traceable to the software
architecture and requirements

R.3.2.3.2 Software code is structured N/A
R.3.2.3.3 Coded software is validated against the module

N/A
specification by static analysis

The module specification is validated against the

N/A
architecture specification by static analysis

R.3.3.3 Software validation ---­ The software is validated with reference to the

N/A
requirements of the software safety requirements
specification

Compliance is checked by simulation of: ----

- input signals present during normal operation N/A

- anticipated occurrences N/A

- undesired conditions requiring system action N/A

TABLE R.1 e – GENERAL FAULT/ERROR CONDITIONS

Component

a

1 CPU

1.1
Registers

Fault/error

Stuck at

Acceptable measures

Functional test, or
periodic self-test using either:

- static memory test, or

- word protection with single

b, c

Definitions Document

reference

for applied

measure

N/A

H.2.16.5
H.2.16.6
H.2.19.6
H.2.19.8.2

Document

reference

for applied

test

Ver-dic

t

bit redundancy

1.2 VOID N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 67 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

1.3
Programme
counter

Stuck at Functional test, or

Periodic self-test, or
Independent time-slot

monitoring, or
Logical monitoring of the

H.2.16.5
H.2.16.6
H.2.18.10.4

H.2.18.10.2

N/A

programme sequence

2
Interrupt
handling
and
execution

3
Clock

4. Memory

4.1
Invariable
memory

4.2
Variable
memory

No
interrupt or
too

Functional test, or
time-slot monitoring

frequent
interrupt

Wrong
frequency
(for quartz

Frequency monitoring, or
time slot monitoring

synchroniz
ed clock:
harmonics/
sub-harmo
nics only)

All single
bit faults

Periodic modified checksum, or
multiple checksum, or
word protection with single bit

redundancy

DC fault Periodic static memory test, or

word protection with single bit
redundancy

H.2.16.5
H.2.18.10.4

H.2.18.10.1
H.2.18.10.4

H.2.19.3.1
H.2.19.3.2
H.2.19.8.2

H.2.19.6
H.2.19.8.2

N/A

N/A

N/A

N/A

4.3
Addressing
(relevant to

Stuck at Word protection with single bit

redundancy including the
address

H.2.19.8.2 N/A

variable and
invariable
memory)

5
Internal

Stuck at Word protection with single bit

redundancy

H.2.19.8.2 N/A

data path

5.1 VOID N/A

5.2
Addressing

Wrong
address

Word protection with single bit
redundancy including the

H.2.19.8.2 N/A

address

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 68 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

6
External
communicat
ion

Hamming
distance 3

Word protection with multi-bit
redundancy, or

CRC – single work, or
Transfer redundancy, or

H.2.19.8.1

H.2.19.4.1
H.2.18.2.2

N/A

Protocol test

H.2.18.14

6.1 VOID N/A

6.2 VOID N/A

6.3
Timing

7
Input/output
periphery

Wrong
point in
time

Wrong
sequence

Fault
conditions
specified in

Time-slot monitoring, or
scheduled transmission
Time-slot and logical

monitoring, or
comparison of redundant

communication channels by
either:

- reciprocal comparison

- independent hardware

comparator
Logical monitoring, or
time-slot monitoring, or
Scheduled transmission

H.2.18.10.4
H.2.18.18
H.2.18.10.3

H.2.18.15
H.2.18.3

H.2.18.10.2
H.2.18.10.4
H.2.18.18

N/A

Plausibility check H.2.18.13 N/A

19.11.2

7.1 VOID N/A

7.2
Analog I/O

7.2.1
A/D and
D/A­converter

7.2.2
Analog

Fault
conditions
specified in

19.11.2
Wrong

addressing

Plausibility check

H.2.18.13

N/A

Plausibility check H.2.18.13 N/A

multiplexer
8 VOID N/A
9

Custom
chips d e.g.
ASIC, GAL,
gate array

Any output
outside the
static and
dynamic
functional

Periodic self-test H.2.16.6 N/A

specificatio
n

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 69 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

NOTE A Stuck-at fault model denotes a fault model representing an open circuit or a non-varying signal
level. A DC fault model denotes a stuck-at fault model incorporating short circuit between signal lines.

a)

For fault/error assessment, some components are divided into their sub-functions.

b)

For each sub-function in the table, the Table R.2 measure will cover the software fault/error.

c)

Where more than one measure is given for a sub-function, these are alternatives.

d)

To be divided as necessary by the manufacturer into sub-functions.

e)

Table R.1 is applied according to the requirements of R.1 to R.2.2.9 inclusive.

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 70 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

10.1 TABLE: Power input deviation

Input deviation of/at: P rated (W) P measured (W)

∆ P Required ∆ P

P

Remark

24VDC 36 26,9 -25,3% +20% ES071-1AE
24VDC 36 31,2 -13,4% +20% ES800
Remark: for 20+5°C

10.2 TABLE: Current deviation for Airtek models

Current deviation of/at: I rated (A) I measured (A) ∆ I

Required ∆ I

P

Remark

24VDC 1,5 1,121 -25,2% +20% ES071-1AE
24VDC 1,5 1,299 -13,4% +20% ES800
Remark: for 20+5°C

11.8-1

TABLE: Heating test, thermocouples for model ES071-1AE

Test voltage (V) ........................................................ : 25,44V, 50Hz

Ambient (°C) ............................................................. :

24,8-25,2

P




Thermocouple locations dT (K) Max. dT (K)
Pin connection 1,1 45
Surface of appliance inlet 1,0 For reference
DC fan motor winding 35,8 80 Class 120
DC fan motor enclosure 25,4 For reference
PCB of DC fan motor 33,3 120
Plastic bracket for fan motor 1,5 For reference
Control PCB 4,8 120
Quick connector on PCB 3,6 For reference
Sync.motor surface 22,2 For reference
Internal wire 0,9 50
Enclosure of water pump 1,4 For reference
Control panel 2,4 75
Appliance enclosure 1,0 75
Handle 1,2 60
Internal wire to appliance inlet 0,9 50
Test corner 1,0 65

11.8-1 TABLE: Heating test, resistance method P

Test voltage (V) ........................................................ : 25,44V

Ambient, t1 (°C) ......................................................... :

Ambient, t2 (°C) ......................................................... :

24,8
25,0





TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 71 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

Temperature rise of winding R1 (Ω) R2 (Ω) dT (K) Max. dT (K) Insulation

class

Synchronous motor winding 67,7 82,5 56,5 75 Class 105

11.8-2

TABLE: Heating test, thermocouples for model ES800

Test voltage (V) ........................................................ : 25,44VDC

Ambient (°C) ............................................................. :

23,5 – 23,0
Thermocouple locations dT (K) Max. dT (K)
Pin connection 2,3 45
Surface of appliance inlet 2,2 For reference
Internal wire to appliance inlet 2,6 50
DC fan motor winding #1 67,6 80 Class 120
DC fan motor winding #2 67,9 80 Class 120
PCB of DC fan motor 53,3 120
Plastic bracket for fan motor 22,7 For reference
Control PCB 9,7 120
Quick connector on PCB 5,1 For reference
Sync.motor surface 15,7 For reference
Internal wire 3,8 50
Control panel 3,3 75

P




Appliance enclosure 1,2 75
Enclosure of water pump 1,1 For reference
Test corner 1,8 65

11.8-2 TABLE: Heating test, resistance method P

Test voltage (V) ........................................................ : 25,44VDC

Ambient, t1 (°C) ......................................................... :

Ambient, t2 (°C) ......................................................... :

21,9
23,1





Temperature rise of winding R1 (Ω) R2 (Ω) dT (K) Max. dT (K) Insulation

class

Synchronous motor winding 67,4 77,3 36,3 75 Class 105

13.2 TABLE: Leakage current N/A

Heating appliances: 1,15 x rated input (W) .......: ----

Motor-operated and combined appliances:

----




1,06 x rated voltage (V) .....................................:

Leakage current between I (mA) Max. allowed I (mA)

---- ---- ----

Supplementary information: --

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 72 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

13.3 TABLE: Electric strength N/A

Test voltage applied between: Test potential applied

(V)

Breakdown / flashover

(Yes/No)

---- ---- ----

Supplementary information: --

14 TABLE: Transient overvoltages N/A

Clearance between: Cl (mm) Required Cl

(mm)

Rated impulse

voltage (V)

Impulse test

voltage (V)

Flashover

(Yes/No)

---- ---- ---- ---- ---- ---­Supplementary information: --

16.2 TABLE: Leakage current N/A

Single phase appliances: 1,06 x rated voltage (V)

----



...........................................................................:

Three phase appliances 1,06 x rated voltage

----



divided by √3 (V) ................................................:

Leakage current between I (mA) Max. allowed I (mA)

---- ---- ----

Remark: record the max. value

16.3 TABLE: Dielectric strength N/A

Test voltage applied between: Test potential applied

(V)

Breakdown / flashover

(Yes/No)

---- ---- ----

Supplementary information: --

17 TABLE: Overload protection N/A

Thermocouple locations Max. temperature rise

measured, ∆ T (K)

Max. temperature rise

limit, ∆ T (K)

---- ---- ---­Supplementary information:

17 TABLE: Overload protection, resistance method N/A

Test voltage (V) ..................................................... :

Ambient, t1 (°C)..................................................... :

Ambient, t2 (°C)..................................................... :

Temperature of winding R1 () R2 () ∆ T (K)

----

----

---­T (°C)





Max. T (°C)

---- ---- ---- ---- ---- ----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 73 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

Supplementary information:

19 Abnormal operation conditions P

Operational characteristics YES/NO Operational conditions
Are there electronic circuits to control

YES Short-circuit for some component

the appliance operation?
Are there “off” or “stand-by” position? YES N/A
The unintended operation of the

NO N/A
appliance results in dangerous
malfunction?

Sub-claus
e

Operating
conditions

description

Test results

description

PEC

description

EMP

19.11.4

Software

type

required

19.11.3
PEC

Final

result

19.2 N/A N/A N/A N.A N/A N/A N/A

19.3 N/A N/A N/A N/A N/A N/A N/A

19.4 N/A N/A N/A N/A N/A N/A N/A

19.5 N/A N/A N/A N/A N/A N/A N/A

19.6 N/A N/A N/A N.A N/A N/A N/A

19.7 N/A N/A N/A N/A N/A N/A N/A

19.8 N/A N/A N/A N/A N/A N/A N/A

19.9 N/A N/A N/A N/A N/A N/A N/A

19.10 N/A N/A N/A N/A N/A N/A N/A

19.11.2 N/A N/A N/A N/A N/A N/A P

19.11.4.8 N/A N/A N/A N/A N/A N/A N/A

19.10X N/A N/A N/A N/A N/A N/A N/A
Supplementary information: --

19.7 TABLE: Abnormal operation, locked rotor/moving parts P

Test voltage (V) ....................................................... : 24V

Ambient, t1 (°C) ........................................................ :

Ambient, t2 (°C) ........................................................ :

Temperature of winding R1 (Ω) R2 (Ω) dT (K)

See below
See below

T (°C)

Max. T (°C)
Lock rotor/moving parts, ambient: (t1: 24,3°C; t2: 24,3°C)
DC fan motor winding --- --- --- 45,2 175
Remark: Impedance protected, no hazards.
Lock rotor/moving parts of Synchronous motor, ambient: (t1: 19,2°C; t2: 19,1°C)
Winding of Synchronous motor 67,7

(24,8°C)

80,9

(24,7°C)

50,7 75,3 165

Remark: Impedance protected.





TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 74 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

Lock rotor/moving parts of water pump, ambient: (t

: 24,8°C; t2: 23,7°C)

1

Water pump surface --- --- --- 24,0 150
Remark: Until steady conditions established.

19.9 TABLE: Abnormal operation, running overload

Test voltage (V) ..................................................... :

Ambient, t1 (°C) .................................................... :

Ambient, t2 (°C) .................................................... :

Temperature of winding R1 () R2 () ∆ T (K)

----

----

---­T (°C)

Max. T (°C)

---- ---- ---- ---- ---- ---­Supplementary information:

19.13 TABLE: Abnormal operation, temperature rises

Thermocouple locations Max. temperature rise

measured, ∆ T (K)

Max. temperature rise

limit, ∆ T (K)

--- --- --­Supplementary information: ---

21.1 TABLE: Impact resistance P

N/A





N/A

Impacts per surface Surface tested Impact energy (Nm) Comments

3 Plastic enclosure 0,5 Pass
3 Control panel 0,5 pass

Supplementary information: ---

24.1 TABLE: Components P
Object / part

No.
Quick

connector of
DC fan motor

DC socket of
ES071-1AE

DC socket of
ES800

Manufacturer/
trademark

Yueqing changshun
electronic co ltd

XUNXINXIN
electronic co ltd

Dongguanyiyu
electronics

Type / model Technical data Standard Mark(s) of

conformity

CS25002(XH) DC500V IEC 60335-1

IEC 60335-2-

Tested with
appliance

80/98

DC005 14,3x9x11mm;

1.65MM; DC
30V/2A

DC-022 --- IEC 60335-1

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-2-

Tested with
appliance

Test with
appliance

80/98

Fan motor Airtek international

corporation limited

YZD-MS001 Input: 24VDC;

30W; 1,25A;
output: 15W ,

IEC 60335-1
IEC 60335-2­80/98

Tested with
appliance

class 130

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 75 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

Swing motor Airtek international

corporation limited

Water pump Airtek international

corporation limited

Internal wire #1 GUANGZHOU ZHIHE

ELECTRONIC CO

TYC50C 18VAC; 50Hz;

5/min <4W

R-001 24VDC; 2,5W;

class120

1007 24-18AWG;

300V; 80°C

LTD

Alternative DONGGUAN CHENG

XING ELECTRONIC

1007 24-18AWG;

300V; 80°C

CO LTD

Alternative GUANGDONG

ZHONGSHAN YIXIN

1007 24-18AWG;

300V; 80°C
ELECTRICAL CO
LTD

Alternative GUANG DONG XIN

LONG ENTERPRISE
CO

1007

24-18AWG;

300V; 80°C

Alternative Various 1007 24-18AWG;

300V; 80°C

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

Tested with
appliance

Tested with
appliance

Tested with
appliance & UL
E251728

Tested with
appliance & UL
E249743

Tested with
appliance & UL
E351034

Tested with
appliance & UL
E207567

S & other EU
certification
marks

Internal wire 2# GUANG DONG XIN

LONG ENTERPRISE
CO

Alternative DONGGUAN CHENG

XING ELECTRONIC

2468

26-18AWG;

300V; 80°C

2468 26-18AWG;

300V; 80°C
CO LTD

Alternative GUANGZHOU ZHIHE

ELECTRONIC CO

2468 26~18AWG;

300V; 80°C
LTD

Alternative GUANGDONG

ZHONGSHAN YIXIN

2468 26~18AWG;

300V; 80°C
ELECTRICAL CO
LTD

Alternative Various 2468 26~18AWG;

300V; 80°C

PCB board SHANDONG JINBAO

ZD-95F V-0; 130°C IEC 60335-1
ELECTRONICS CO.,
LTD

Alternative ZHONGSHAN LIXIN

FR-1 V-0; 130°C IEC 60335-1
CHAIN-BOARD CO.,
LTD

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-2­80/98

IEC 60335-2­80/98

Tested with
appliance & UL
E207567

Tested with
appliance & UL
E249743

Tested with
appliance & UL
E251728

Tested with
appliance & UL
E351034

S & other EU
certification
marks

Tested with
appliance & UL
E141940

Tested with
appliance & UL
E230073

Alternative SHUNDE JUN'AN

SHENGSHENG
ELECTRONIC CO.,

S-V01 V-0; 130°C IEC 60335-1

IEC 60335-2­80/98

Tested with
appliance & UL
E240257

LTD.

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Control panel
stickers of
ES071-1AE

Page 76 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

Maoming sakata inx
Co., Ltd.

Base material

PVC +surface

printing ink

--- IEC 60335-1
IEC 60335-2­80/98

Test with
appliance

Top cover of
ES071-1AE

Plastic
enclosure of
ES071-1AE

Rear grille of
ES071-1AE

DC motor
bracket

Vertical louver
blade ES071­1AE

Control panel of
ES071-1AE

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

Tested with
appliance & UL
E67171

Tested with
appliance & UL
E67171

Tested with
appliance & UL
E67171

Tested with
appliance & UL
E67171

Tested with
appliance & UL
E67171

Test with
appliance &

UL E67171

Top cover/
water pump
front panel/
Louver Blade/
rear grille/
handle of
ES800

Plastic
enclosure of
ES800

Control panel of
ES800

Lead wire of
Water tank
switch /Low
water alarm
device for
ES800
(optional )

Alternative

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

LG CHEM LTD HI121(#) HB, 95 °C IEC 60335-1

IEC 60335-2­80/98

DONGGUAN NANSI
CABLE AND WIRE
CO LTD

SHENZHEN YIMEITE
ELECTRIC CABLE
CO LTD

2464 80°C; 300V;

24AWG

2464 80°C; 300V;

24AWG

IEC 60335-1
IEC 60335-2-

80/98

IEC 60335-1
IEC 60335-2-

80/98

Tested with
appliance & UL
E67171

Tested with
appliance & UL
E67171

Tested with
appliance & UL
E67171

Tested with
appliance & UL
E468498

Tested with
appliance & UL
E 318342

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 77 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

Lead wire of
Water level
LED light for

GUANG DONG XIN
LONG ENTERPRISE
CO

2468

26-18AWG;
300V; 80°C

ES800
(optional )

Alternative DONGGUAN CHENG

XING ELECTRONIC

2468 26-18AWG;

300V; 80°C

CO LTD

Alternative GUANGZHOU ZHIHE

ELECTRONIC CO

2468 26~18AWG;

300V; 80°C

LTD

Alternative GUANGDONG

ZHONGSHAN YIXIN

2468 26~18AWG;

300V; 80°C
ELECTRICAL CO
LTD

Alternative Various 2468 26~18AWG;

300V; 80°C

Note: this appliance can be powered by the following adapter mode
Adapter Foshan city Dizhi

power supply Co., Ltd.

DSS36­2401500-H

Input: AC 100-

240V; 50/60Hz;

1,5A; Output:

24V; 1,5A; Class

II

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC 60335-1
IEC 60335-2­80/98

IEC/EN 61558-2­16

Tested with
appliance & UL
E207567

Tested with
appliance & UL
E249743

Tested with
appliance & UL
E251728

Tested with
appliance & UL
E351034

S & other EU
certification
marks

TUV Rheinland
S 50316491

Alternative Dongguan yuan shuai

electronic Co., Ltd

YeS36W­2400150V

Input :100-

240V~; 50/60Hz;

1,0A Max;

IEC/EN 61558-2­16

Intertek
16HKS0430-

01
Output : 24V;
1,5A; Class II

Alternative Various Various Input: AC 100-

240V; 50/60Hz;
1,5A or 1,0A;

IEC/EN 61558-2­16

S & other EU

certification

marks
Output: 24V;
1,5A; Class II

Supplementary information:

1

) Provided evidence ensures the agreed level of compliance. See OD-CB2039.

28.1 TABLE: Threaded part torque test

Threaded part identification

Diameter of thread

(mm)

Column number

(I, II, or III)

Applied torque (Nm)

Fixing screw 3,37 II 0,8
Supplementary information: --

29.1 TABLE: Clearances P

P

Overvoltage category ............................................ : II



Type of insulation:

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 78 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

Rated impulse

voltage (V):

330 0,2* / 0,5 / 0,8**
500

800 0,2* / 0,5 / 0,8**
1 500 0,5 / 0,8** / 1,0***
2 500

Min. cl (mm) Basic

(mm)

0,2* / 0,5 / 0,8**

1,5 / 2,0***

Supplementary

(mm)

Reinforced

(mm)

Functional

(mm)

Verdict / Remark

-- -- -- -- N/A

-- -- -- 3,2 P

-- -- -- -- N/A

-- -- -- -- N/A

-- -- -- -- N/A
4 000 3,0 / 3,5*** -- -- -- -- N/A
6 000 5,5 / 6,0*** -- -- -- -- N/A
8 000 8,0 / 8,5*** -- -- -- -- N/A

10 000 11,0 / 11,5*** -- -- -- -- N/A
Supplementary information:
*) For tracks on printed circuit boards if pollution degree 1 and 2

**) For pollution degree 3
***) If the construction is affected by wear, distortion, movement of the parts or during assembly

29.2 TABLE: Creepage distances, basic, supplementary and reinforced insulation

N/A

Working voltage

(V)

Creepage distance

(mm)

Pollution degree

1 2 3 Type of insulation Verdict

Material group Material group

≤50
≤50
≤50

125
125
125

I II IIIa/IIIb
0,18 0,6 0,85
0,18 0,6 0,85

1,2 1,5 1,7 1,9

1,2 1,5 1,7 1,9
0,36 1,2 1,7 2,4 3,0 3,4 3,8
0,28 0,75 1,05
0,28 0,75 1,05

1,5 1,9 2,1 2,4

1,5 1,9 2,1 2,4
0,56 1,5 2,1 3,0 3,8 4,2 4,8

I II IIIa/IIIb* B** S** R**

250 0,56 1,25 1,8 2,5 3,2 3,6 4,0
250 0,56 1,25 1,8 2,5 3,2 3,6 4,0
250 1,12 2,5 3,6 5,0 6,4 7,2 8,0
400 1,0 2,0 2,8 4,0 5,0 5,6 6,3
400 1,0 2,0 2,8 4,0 5,0 5,6 6,3


 

 

 


 



 





N/A

 



 



N/A
N/A

N/A

N/A
N/A

N/A
N/A

N/A

N/A

N/A
400 2,0 4,0 5,6 8,0 10,0 11,2 12,6
500 1,3 2,5 3,6 5,0 6,3 7,1 8,0
500 1,3 2,5 3,6 5,0 6,3 7,1 8,0
500 2,6 5,0 7,2 10,0 12,6 14,2 16,0

 

 

 

N/A

N/A



N/A

N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 79 of 116 Report No.: 160421073GZU-003

 

 

 

Modification 1: October 12, 2016

29.2 TABLE: Creepage distances, basic, supplementary and reinforced insulation

Working voltage

(V)

Creepage distance

(mm)

Pollution degree

1 2 3 Type of insulation Verdict

Material group Material group

>630 and ≤800
>630 and ≤800

>630 and ≤800
>800 and ≤1000
>800 and ≤1000
>800 and ≤1000

>1000 and ≤1250
>1000 and ≤1250
>1000 and ≤1250
>1250 and ≤1600

I II IIIa/IIIb
1,8 3,2 4,5 6,3 8,0 9,0 10,0
1,8 3,2 4,5 6,3 8,0 9,0 10,0
3,6 6,4 9,0 12,6 16,0 18,0 20,0
2,4 4,0 5,6 8,0 10,0 11,0 12,5
2,4 4,0 5,6 8,0 10,0 11,0 12,5
4,8 8,0 11,2 16,0 20,0 22,0 25,0
3,2 5,0 7,1 10,0 12,5 14,0 16,0
3,2 5,0 7,1 10,0 12,5 14,0 16,0
6,4 10,0 14,2 20,0 25,0 28,0 32,0
4,2 6,3 9,0 12,5 16,0 18,0 20,0

I II IIIa/IIIb* B** S** R**

 

 

 

 

 

 

 

N/A

N/A



N/A

N/A

N/A



N/A

N/A

N/A



N/A

N/A

N/A

>1250 and ≤1600
>1250 and ≤1600
>1600 and ≤2000
>1600 and ≤2000
>1600 and ≤2000
>2000 and ≤2500
>2000 and ≤2500
>2000 and ≤2500
>2500 and ≤3200
>2500 and ≤3200
>2500 and ≤3200
>3200 and ≤4000
>3200 and ≤4000
>3200 and ≤4000
>4000 and ≤5000
>4000 and ≤5000

4,2 6,3 9,0 12,5 16,0 18,0 20,0
8,4 12,6 18,0 25,0 32,0 36,0 40,0
5,6 8,0 11,0 16,0 20,0 22,0 25,0
5,6 8,0 11,0 16,0 20,0 22,0 25,0

11,2 16,0 22,0 32,0 40,0 44,0 50,0

7,5 10,0 14,0 20,0 25,0 28,0 32,0

7,5 10,0 14,0 20,0 25,0 28,0 32,0
15,0 20,0 28,0 40,0 50,0 56,0 64,0
10,0 12,5 18,0 25,0 32,0 36,0 40,0
10,0 12,5 18,0 25,0 32,0 36,0 40,0
20,0 25,0 36,0 50,0 64,0 72,0 80,0
12,5 16,0 22,0 32,0 40,0 45,0 50,0
12,5 16,0 22,0 32,0 40,0 45,0 50,0
25,0 32,0 44,0 64,0 80,0 90,0 100,0
16,0 20,0 28,0 40,0 50,0 56,0 63,0
16,0 20,0 28,0 40,0 50,0 56,0 63,0


 

 

 

 

 

 

 

 


 




N/A

N/A

N/A



N/A

N/A

N/A



N/A

N/A

N/A



N/A

N/A

N/A



N/A

N/A

N/A



N/A

>4000 and ≤5000
>5000 and ≤6300
>5000 and ≤6300
>5000 and ≤6300

32,0 40,0 56,0 80,0 100,0 112,0 126,0
20,0 25,0 36,0 50,0 63,0 71,0 80,0
20,0 25,0 36,0 50,0 63,0 71,0 80,0
40,0 50,0 72,0 100,0 126,0 142,0 160,0

 


N/A

N/A



N/A

N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 80 of 116 Report No.: 160421073GZU-003



 



 



 

Modification 1: October 12, 2016

29.2 TABLE: Creepage distances, basic, supplementary and reinforced insulation

Working voltage

(V)

Creepage distance

(mm)

Pollution degree

1 2 3 Type of insulation Verdict

Material group Material group

>6300 and ≤8000
>6300 and ≤8000

>6300 and ≤8000
>8000 and ≤10000
>8000 and ≤10000
>8000 and ≤10000

>10000 and ≤12500
>10000 and ≤12500
>10000 and ≤12500

I II IIIa/IIIb
25,0 32,0 45,0 63,0 80,0 90,0 100,0
25,0 32,0 45,0 63,0 80,0 90,0 100,0
50,0 64,0 90,0 126,0 160,0 180,0 200,0
32,0 40,0 56,0 80,0 100,0 110,0 125,0
32,0 40,0 56,0 80,0 100,0 110,0 125,0
64,0 80,0 112,0 160,0 200,0 220,0 250,0
40,0 50,0 71,0 100,0 125,0 140,0 160,0
40,0 50,0 71,0 100,0 125,0 140,0 160,0
80,0 100,0 142,0 200,0 250,0 280,0 320,0

I II IIIa/IIIb* B** S** R**

 

 

 

Supplementary information:

N/A

N/A



N/A

N/A

N/A



N/A

N/A

N/A



N/A

N/A

*) Material group IIIb is allowed if the working voltage does not exceed 50 V

29.2 TABLE: Creepage distances, functional insulation

Working voltage

(V)

Creepage distance

(mm)

Pollution degree
1 2 3
Material group Material group
I II IIIa/IIIb

≤10

0,08 0,4 0,4 0,4 1,0 1,0 1,0 N/A

I II IIIa/IIIb*

50 0,16 0,56 0,8 1,0 1,4 1,6
125 0,25 0,71 1,0 1,4 1,8 2,0 2,2 N/A
250 0,42 1,0 1,4 2,0 2,5 2,8 3,2 N/A
400 0,75 1,6 2,2 3,2 4,0 4,5 5,0 N/A
500 1,0 2,0 2,8 4,0 5,0 5,6 6,3 N/A

>630 and ≤800

>800 and ≤1000

1,8 3,2 4,5 6,3 8,0 9,0 10,0 N/A
2,4 4,0 5,6 8,0 10,0 11,0 12,5 N/A

1,8

P

)

Verdict / Remark

P/ 3,2mm

>1000 and ≤1250
>1250 and ≤1600
>1600 and ≤2000
>2000 and ≤2500

3,2 5,0 7,1 10,0 12,5 14,0 16,0 N/A
4,2 6,3 9,0 12,5 16,0 18,0 20,0 N/A
5,6 8,0 11,0 16,0 20,0 22,0 25,0 N/A
7,5 10,0 14,0

20,0 25,0 28,0 32,0 N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 81 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

>2500 and ≤3200
>3200 and ≤4000
>4000 and ≤5000
>5000 and ≤6300
>6300 and ≤8000

>8000 and ≤10000

>10000 and ≤12500

10,0
12,5 16,0 22,0
16,0 20,0 28,0
20,0 25,0 36,0
25,0 32,0 45,0
32,0 40,0 56,0
40,0 50,0 71,0 100,0 125,0 140,0 160,0

12,5 18,0

25,0 32,0 36,0 40,0 N/A
32,0 40,0 45,0 50,0 N/A
40,0 50,0 56,0 63,0 N/A
50,0 63,0 71,0 80,0 N/A
63,0 80,0 90,0 100,0
80,0 100,0 110,0 125,0

Supplementary information:
*) Material group IIIb is allowed if the working voltage does not exceed 50 V

N/A
N/A
N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 82 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

30
Object/

part No.

75 125 cl. 11

Plastic

TABLE: Resistance to heat and fire
Manufacturer/

trademark

Type/
model

Ball pressure test

--- --- P ---

°C

+40

cl. 19

+25

550 650 750 85

--- --- P ---

enclosure
Quick

--- --- --- P --- --- --- ---

connector
DC socket --- --- --- P --- --- --- ---

Water

--- --- P ---

--- --- P --­pump
enclosure

Electric

--- --- P ---

--- --- P --­box

Glow wire test

(GWT)

°C

t

e

t

i

te t

---

---

---

No
flame

---

3,0

s

---

---

---

---

---

2,

6s

---

---

i

Glow-wire

flammability index

(GWFI)

°C

Glow- wire

ignition

temp.

(GWIT)

Needle-

flame

test

(NFT)

°C

550 650 750 850 675 775

0

--- ---

P

---

P

---

--- ---

--- ---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

--- ---

---

---

---

---

---

--- P

--- ---

--- --- P

---

---

--- P

P P

Verdict

P

Fan motor

--- --- P ---

--- --- P ---

---

---

---

--- ---

---

---

---

---

---

--- P

bracket
PCB --- --- --- P --- --- --- ---

---

---

---

--- ---

---

---

---

---

---

P P

Supplementary information:

1)

Parts of material classified at least HB40 or if relevant HBF

2)

Parts of material classified as V-0 or V-1

3)

Flame persisting longer than 2 s (= te – ti) need only be reported for unattended appliances

4)

Surrounding parts subjected to the needle-flame test of annex E

5)

Base material classified as V-0 or if relevant VTM-0

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 83 of 116 Report No.: 160421073GZU-003

6)

The GWIT pre-selection option, the 850 °C GWFI pre-selection option, and the 850 °C GWT are not applicable for attended appliances

Modification 1: October 12, 2016

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 84 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Appendix EMF

P

TEST: Evaluation of the magnetic fields

—
Applied standards: IEC 62233:2005, EN 62233:2008 (incl. Corr.1:2008) —
Method Used method: 5.5.2 Time domain evaluation —
Applied Limit ICNIRP Guidelines —
Identification of the appliance Type of apparatus Evaporative air cooler

Rated Voltage 24
Rated Frequency —

Parameters required prior to the test Laboratory Ambient Temperature

25 °C ± 10 °C
Supply Voltage (Rated Voltage ± 2 %) V
Supply Frequency (Rated Frequency ± 2 %) Hz

Parameters recorded during the test Laboratory Ambient Temperature

25
Supply Voltage 24
Supply Frequency —

Operating Mode Normal operation
Method 5.5.2

Measuring Positions Measuring Distance Coupling Factor Measurement Uncertainty

Around 30cm — —

Frequency (kHz) Limit (%) Measured Maximum Value (%)

0,01 to 400 100 0,220
Supplementary information:
The measured maximum value in this table may be weighted with the coupling factor if applicable, and the

measurement uncertainty is applied if the measured result is more than 75 % of the limit.

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 85 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Appendix to TRF no. IEC60335_2_98E

IEC 60335-2-80:2002 + A1:2004 + A2:2008
Clause Requirement – Test Result – Remark Verdict
5 GENERAL CONDITIONS FOR THE TESTS

5.7 Fans intended to be used in tropical climates, tests of

---

N/A

clauses 10, 11 and 13 are carried out at 40 °C +/-
2 °C (IEC/EN 60335-2-80)

Fans marked with an ambient operating temperature,

N/A

tests of clauses 10, 11 and 13 are carried out at the
marked value +/- 2 °C (IEC/EN 60335-2-80/ A1)

6 CLASSIFICATION

6.2 Duct fans shall be at least IP X2

---

N/A

(IEC/EN 60335-2-80)

6.101

Classification to climatic conditions : temperate

Temperate climates

P

climates, tropical climates (IEC/EN 60335-2-80)

7 MARKING AND INSTRUCTIONS

7.1

For tropical climates marked with letter T

---

N/A

(IEC/EN 60335-2-80)
Fans operating at local temperature exceeding 40 °C

N/A
marked with ambient operating temperature
(IEC/EN 60335-2-80/ A1)

8 PROTECTION AGAINST ACCESS TO LIVE PARTS

8.2 Removal of detachable parts after user maintenance,

---

N/A
basic insulation may be touched provided that wiring

is electrically equivalent with IEC 60227 or IEC 60245
(IEC/EN 60335-2-80/A1)

15 MOISTURE RESISTANCE

15.1.1 The outer part of fans to be installed in the external

---

N/A
structure is subjected to subclause 14.2.4(a) of IEC

60529. (IEC/EN 60335-2-80/A1)

19 ABNORMAL OPERATION

19.1

Fans incorporating shutters or similar subjected to

--­P

the test of cl. 19.101 (IEC/EN 60335-2-80)

19.9 Not applicable (IEC/EN 60335-2-80)

19.101

Fans incorporating shutters or similar that are

N/A

P

operated automatically are supplied at rated voltage
in the closed or open position, whichever is more
unfavourable (IEC/EN 60335-2-80)

20 STABILITY AND MECHANICAL HAZARDS

20.101

Fan blades, other than those for mounting at high

--­P

level, shall be guarded, unless ...............................

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 86 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

(IEC/EN 60335-2-80)

21 MECHANICAL STRENGTH

21.101

Fan guards are subjected to a push and pull force of

--­P

20 N. Dangerous moving parts are not accessible
(IEC/EN 60335-2-80)

(Addition:)

P

The test probe is applied with a force not exceeding
5 N. (IEC/EN 60335-2-80/A2)

21.102

Ceiling fans have adequate strength. Load four times

mass (.......) (IEC/EN 60335-2-80)

22 CONSTRUCTION

22.101

Appliances having provision for attaching a luminaire
incorporate appropriate terminals and internal wiring
(IEC/EN 60335-2-80)

23 INTERNAL WIRING

23.3

No damage after 100 000 flexings for conductors
flexed during normal use and at rated voltage
(IEC/EN 60335-2-80)

24 COMPONENTS

24.2

Switches or automatic controls in flexible cords are
allowed for appliances not exceeding 25 W
(IEC/EN 60335-2-80)

24.101

Thermal cut-outs in duct fans in order to comply with
cl. 19 are not self-resetting (IEC/EN 60335-2-80)

25 SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS

25.5 - type Z attachment is allowed for portable fans
(IEC/EN 60335-2-80)

29 CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION

29.2

Microenvironment is pollution degree 3 unless
insulation is enclosed or located that it is unlikely to
be exposed to pollution during normal use (IEC/EN
60335-2-80)

N/A

---

N/A

---

N/A

---

N/A

N/A

---

N/A

---

N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 87 of 116 Report No.: 160421073GZU-003

appliance in a safe way and understand the hazards

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

ATTACHMENT TO TEST REPORT IEC 60335-2-98

EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES

Household and similar electrical appliances – Safety –

Part 2-98: Particular requirements for humidifiers

Differences according to :

EN 60335-2-98:2003 + A1:2005 + A2:2008
EN 60335-2-80:2003 + A1:2004 +A2:2009
EN 60335-1:2012 + A11:2014

Attachment Form No. :
Attachment Originator :
Master Attachment :

EU_GD_IEC60335_2_98E
VDE
2013-06

Copyright © 2013 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.

CENELEC COMMON MODIFICATIONS

6.1 Delete “class 0” and “class 01” N/A

7.1 Single-phase appliances to be connected to the

P

supply mains: 230 V covered

Multi-phase appliances to be connected to the

N/A

supply mains: 400 V covered

7.10 Devices used to start/stop operational functions of

P
the appliance distinguished from other manual
devices by means of shape, size, surface texture,
position, etc.

An indication that the device has been operated is given by: ----

- a tactile feedback, or P

- an audible and visual feedback P

7.12 The instructions include the substance of the following: ----

- this appliance can be used by children aged from

P
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the

involved

- children shall not play with the appliance P

- cleaning and user maintenance shall not be made

P
by children without supervision

7.12.Z1 The specific instructions related to the safe

P
operation of this appliance is collated together in the
front section of the user instructions

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 88 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

The height of the characters, measured on the

P
capital letters, is at least 3 mm

These instructions are also available in an

P
alternative format, e.g. on a website

8.1.1 Also test probe 18 of EN 61032 is applied N/A
The appliance being in every possible position

N/A
during the test

The force on the probe in the straight position is

N/A
increased to 10 N when probe 18 is used

When using test probe 18 the appliance is fully

N/A
assembled as in normal use without any parts
removed, and

parts intended to be removed for user maintenance

N/A
are also not removed

8.2 Compliance is checked by applying the test probes

N/A
of EN 61032

For built-in appliances and fixed appliances, the test

N/A
probe B and probe 18 of EN 61032 are applied only
after installation

11.8 Footnotes to “External enclosure of motor-operated

P
appliances” to be taken into account

15.1.2 Appliances with an automatic cord reel tested with

N/A
the cord in the most unfavourable position so that
the reeling of the wet cord may affect electrical
insulation during operation, the cord not being dried
before reeling

20.2 When using the test probe similar to test probe B

P
with a circular stop face, the accessories and
detachable covers are removed

Test probe 18 applied with a force of 2,5 N on the

P
appliance fully assembled

24.1 Components comply with the safety requirements

P
specified in the relevant standards as far as they
reasonably apply

The requirements of clause 29 of this standard

P
apply between live parts of components and
accessible parts of the appliance.

The requirements of 30.2 of this standard apply to

P
parts of non-metallic material in components
including parts of non-metallic material supporting
current-carrying connections inside components

Components that have not been previously tested

P
or do not comply with the standard for the relevant
component are tested according to the
requirements of 30.2

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 89 of 116 Report No.: 160421073GZU-003

additional tests specified in the relevant standard for

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Components that have been previously tested and shown to comply with the

---­resistance to fire requirements in the standard for the relevant component need not
be retested provided that:

- the severity specified in the component standard is
not less than the severity specified in 30.2, and

- the test report for the component states whether it
complied with the standard for the relevant
component with or without flame, flames not
exceeding 2 s during the test are ignored

Unless components have been previously tested

and found to comply with the relevant standard for
the number of cycles specified, they are tested in
accordance with 24.1.1 to 24.1.9

For components mentioned in 24.1.1 to 24.1.9, no

the component are necessary other than those
specified in 24.1.1 to 24.1.9

Components that have not been separately tested

and found to comply with the relevant standard, and

components that are not marked or not used in

accordance with their marking,

are tested in accordance with the conditions

occurring in the appliance, the number of samples
being that required by the relevant standard

Lamp holders and starter holders that have not

been previously tested and found to comply with the
relevant standard are tested as a part of the
appliance and additionally comply with the gauging
and interchangeability requirements of the relevant
standard under the conditions occurring in the
appliance

N/A

N/A

P

P

P

N/A

P

N/A

Where the relevant standard specifies these

gauging and interchangeability requirements at
elevated temperatures, the temperatures measured
during the tests of clause 11 are used

Plugs and socket-outlets and other connecting

devices of interconnection cords are not
interchangeable with plugs and socket-outlets listed
in IEC/TR 60083 or IEC 60906-1, or

with connectors and appliance inlets complying with

the standard sheets of IEC 60320-1,

if direct supply to these parts from the supply mains

gives rise to a hazard

24.1.7 If the remote operation of the appliance is via a
telecommunication network, the relevant standard
for the telecommunication interface circuitry in the
appliance is EN 41003

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

N/A

N/A

N/A

N/A

N/A

Tel: [phone] Fax: [phone]

Page 90 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Compliance with clause 8 of this standard is not

N/A
impaired by connecting the appliance to a device
covered by EN 41003

24.Z1 For motor running capacitors (IEC 60252-1 type P2)

N/A
with a metallic enclosure having an overpressure
fuse the flame testing of internal plastic parts
supporting current carrying connections as required
in 30.2.2 and 30.2.3.1 is not necessary

25.6 Supply cords of single-phase portable appliances having a rated current not
exceeding 16 A, fitted with a plug complying with the following standard sheets of
IEC/TR 60083:

- for class I appliances:

N/A

standard sheet C2b, C3b or C4 ............................ :

- for class II appliances:

N/A

standard sheet C5 or C6 ....................................... :

25.7 Rubber sheathed cords (60245 IEC 53) are not

N/A
suitable for appliances intended to be used
outdoors or when they are liable to be exposed to
significant amount of ultraviolet radiation

Halogen-free thermoplastic compound sheathed supply cords have properties at

least those of:

- halogen-free thermoplastic compound

N/A

sheathed cords (H03Z1Z1H2-F or H03Z1Z1-F),
for appliances having a mass not exceeding 3
kg

----

----

- halogen-free thermoplastic compound
sheathed cords (H05Z1Z1H2-F or H05Z1Z1-F),
for other appliances

Cross-linked halogen-free compound sheathed

supply cords have properties at least those of
cross-linked halogen-free compound sheathed
cords (H07ZZ-F)

26.11 Conductors connected by soldering are not

considered to be positioned or fixed so that reliance
is not placed upon the soldering alone to maintain
them in position unless they are held in place near
the terminals independently of the solder

29.3.Z1 Appliance constructed so that if there is a possibility

of damaging the insulation during installation, the
insulation withstands the scratch and penetration
test of 21.2

32 Compliance regarding electromagnetic fields is

checked according to EN 62233

Annex I,

19.I.101

The appliance is supplied at rated voltage and
operated under normal operation with each of the
fault conditions specified

N/A

N/A

P

N/A

P

N/A

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 91 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

The duration of the test is as specified in 19.7 N/A
ZA ANNEX ZA (NORMATIVE)

----

SPECIAL NATIONAL CONDITIONS

Norway

19.5 The test is also applicable to appliances intended to

N/A

----

be permanently connected to fixed wiring

Norway

22.2 The second paragraph of this subclause, dealing

N/A

----

with single-phase, permanently connected class I
appliances having heating elements, is not
applicable due to the supply system

25.6 and

25.25

All CENELEC countries
Information concerning National plug and

socket-outlets is available from the CENELEC

N/A

----

website. Normative national requirements
concerning plug and socket-outlets are shown in
the relevant National standard

Ireland and United Kingdom

----

25.8 In the table, the lines for 10 A and 16 A are replaced by: ----

> 10 and ≤ 13 1,25 N/A
> 13 and ≤ 16 1,5 N/A

ZB ANNEX ZB (INFORMATIVE)

A-DEVIATIONS

Ireland

25.6 These regulations apply to all plugs for domestic

----

N/A
use at a voltage of not less than 200 V and in
general allow only plugs complying with I.S.
401:1997, or equivalent, to be fitted to domestic
appliances

United Kingdom

----

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 92 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

25.6 These regulations apply to all plugs for domestic

N/A
use at a voltage of not less than 200 V and in
general allow only plugs to BS 1363 to be fitted to
domestic appliances. It also allows plugs to
BS 4573 and EN 50075 to be fitted to shavers and
toothbrushes

ZC

ANNEX ZC (NORMATIVE)
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR

----

CORRESPONDING EUROPEAN PUBLICATIONS

A list of referenced documents in this standard P

ZD ANNEX ZD (INFORMATIVE)

----

IEC and CENELEC CODE DESIGNATIONS FOR FLEXIBLE CORDS

A table with IEC and CENELEC code designations

P
for flexible cords

ZE ANNEX ZE (INFORMATIVE)

----

SPECIFIC ADDITIONAL REQUIREMENTS FOR APPLIANCES AND MACHINES
INTENDED FOR COMMERCIAL USE

7.1 Business name and full address of the

N/A
manufacturer and, where applicable, his authorized

representative ....................................................... :

Model or type reference ........................................ : N/A

Serial number, if any ............................................. : N/A

Production year N/A

Designation of the appliance ................................. : N/A

7.12 Instructions provided with the appliance so that the

N/A
appliance can be used safely

The instructions contain at least the following information: ----

- the business name and full address of the

N/A
manufacturer and, where applicable, his authorized
representative

- model or type reference of the appliance as

N/A
marked on the appliance itself, except for the serial
number

- the designation of the appliance together with its

N/A
explanation in case it is given by a combination of
letters and/or numbers

- the general description of the appliance, when

N/A
needed due to the complexity of the appliance

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 93 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- specific precautions if required during installation,

N/A
operation, adjusting, user maintenance, cleaning,
repairing or moving

- when needed drawings, diagrams, descriptions
and explanations necessary for the safe use and
user maintenance of the appliance

- the possible reasonably foreseeable misuse and,
whenever relevant, a warning against the effects it
may have on the safe use of the appliance

The words “Original instructions” appear on the

language version(s) verified by the manufacturer or
by the authorized representative

When a translation of the original instructions has

been provided by a person introducing the
appliance on the market; the meaning of the
sentence “Translation of the original instructions”
appear in the relevant instructions delivered with the
appliance

The instructions for maintenance/service to be done

by specialized personnel, mandated by the
manufacturer or the authorized representative may
be supplied in only one Community language which
the specialized personnel understand

The instructions indicate the type and frequency of

inspections and maintenance required for safe
operation including the preventive maintenance
measures

N/A

N/A

N/A

N/A

N/A

N/A

7.12.ZE1 If needed for specific appliances, the following information to be given: ----

- on use, transportation, assembly, dismantling

N/A
when out of service, testing or foreseeable
breakdowns, if these operations have
consequences on stability of the appliance in
order to avoid overturning, falling or uncontrolled
movements of the appliance or of its component
parts

- on how to maintain adequate mechanical

N/A
stability when in use, during transportation,
assembly, dismantling, scrapping and any other
action involving the appliance

- on the protective measures to be taken by the

N/A
user, including, where appropriate, the personal
protective equipment to be provided

- on the operating method to be followed in the

N/A
event of accident or breakdown; if a blockage is
likely to occur the operating method to safely
unblock the appliance

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 94 of 116 Report No.: 160421073GZU-003

The appliance continues to operate, without causing

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- on the specifications on the spare parts to be

N/A
used, when these affect the health and safety of
the operator

- on airborne noise emissions, determined and declared in accordance with the
relevant Part 2, which includes:

- the A-weighted emission sound pressure

N/A
level at workstations, where this exceeds

70 dB(A) ......................................................... ;

- where this level does not exceed 70 dB(A),

N/A
this fact is indicated

- the peak C-weighted instantaneous sound

N/A
pressure value at workstations, where this
exceeds 63 Pa (130 dB in relation to 20 µPa) :

- the A-weighted sound power level emitted by

N/A
the machinery, where the A-weighted emission
sound pressure level at workstations exceeds

80 dB(A) ......................................................... :

7.12.ZE2 The instructions includes a warning to disconnect

N/A

the appliance from its power source during service
and when replacing parts

If the removal of the plug is foreseen, it is clearly

N/A

indicated that the removal of the plug has to be
such that an operator can check from any of the
points to which he has access that the plug remains
removed

----

If this is not possible, due to the construction of the

N/A

appliance or its installation, a disconnection with a
locking system in the isolated position is provided

19.11.4.8

N/A

any hazard to the user, from the same point in its
operating cycle at which the voltage fluctuation
occurred, or

a manual operation is required to restart it N/A

20.1 Appliances and their components and fittings have

N/A

adequate mechanical stability during transportation,
assembly, dismantling and any other action
involving the appliance

20.2 Dangerous moving transmission parts safeguarded

N/A

either by design or guards

When guards are used, they are fixed guards,

N/A

interlocking movable guards or protective devices

Moving parts directly involved in the function of the appliance which cannot be made

----

completely inaccessible fitted with:

- fixed guards or interlocking movable guards

N/A

preventing access to those sections of the parts
that are not used in the work, and

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 95 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

- adjustable guards restricting access to those

N/A

sections of the moving parts where access is
necessary

Interlocking movable guards used where frequent

access is required

21.1 Appliances and their components and fittings have
adequate mechanical strength and is constructed to
withstand such rough handling that may be
expected in normal use, during transportation,
assembly, dismantling, scrapping and any other
action involving the appliance

22.ZE.1 For appliances provided with a seat, the seat gives
adequate stability

The distance between the seat and the control

devices capable of being adapted to the operator

22.ZE.2 For appliances provided with separate devices for
the start and the stop functions, the stop function is
unambiguously identifiable and does always
override the start function

For appliances provided with one device performing

the start and the stop function, the stop function is
unambiguously identifiable and does always
override the start function

22.ZE.3 Appliances designed in such a way that incorrect
mounting is avoided, if this can lead to an unsafe
situation

N/A

N/A

N/A

N/A

N/A

N/A

N/A

If this is not possible, information on the correct

N/A
mounting is given directly on the part and/or the
enclosure

22.ZE.4 Where the weight, size or shape prevents

N/A
appliances from being moved manually, they are
fitted with attachments for lifting gear, or

so designed that they can be fitted with such

N/A
attachments, or

be shaped in such a way that standard lifting gear

N/A
can easily be used

Appliances to be moved manually are constructed

N/A
or equipped so that they can be moved easily and
safely

22.ZE.5 The fixing systems of fixed guards which prevent

N/A
access to dangerous moving transmission parts
only removable with the use of tools

If such guards have to be removed by the user for

N/A
routine cleaning or maintenance their fixing systems
remain attached to the fixed guards or to the
machine after removal

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 96 of 116 Report No.: 160421073GZU-003

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

Where possible, guards are incapable of remaining

N/A
in place without their fixings

This does not apply if, after removal of the screws,

N/A
or if the component is incorrectly repositioned, the
appliance becomes inoperative

Movable guards are interlocked N/A
The interlocking devices prevent the start of

N/A
hazardous appliance functions until the guards are
fixed in their position, and give a stop command
whenever they are no longer closed

Where it is possible for an operator to reach the danger zone before the risk due to

---­hazardous appliance functions has ceased, movable guards associated with a
guard locking device in addition to an interlocking device that:

- prevents the start of hazardous appliance

N/A

functions until the guard is closed and locked, and

- keeps the guard closed and locked until the risk of

N/A
injury from the hazardous appliance functions has
ceased

Interlocking movable guards remain attached to the

N/A
appliance when open, and

they are designed and constructed in such a way

N/A
that they can be adjusted only by means of an
intentional action

22.ZE.6 Interlocking movable guards designed in such a

N/A
way that the absence or failure of one of their
components prevents starting or stops the
hazardous appliance functions

The guard is opened to the extent needed to cause

N/A
the interlocking to operate and is then closed, the
number of operations being defined in the specific

Part 2 .................................................................... :

After this test any defect that may be expected in

N/A
normal use is applied to the interlock system,
including interruption of the supply, only one defect
being simulated at a time

After these tests the interlock system is fit for

N/A
further use

22.ZE.7 Adjustable guards restricting access to areas of the moving parts strictly necessary

----

for the work are:

- adjustable manually or automatically, depending

N/A
on the type of work involved, and

- readily adjustable without the use of tools N/A

22.ZE.8 In case of interruption, re-establishment after an

N/A
interruption or fluctuation in whatever manner of the
power supply, the appliance does not restart

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 97 of 116 Report No.: 160421073GZU-003

Appliances fitted with means to isolate them from all

Modification 1: October 12, 2016

IEC 60335-2-98

Clause Requirement + Test Result - Remark Verdict

However, automatic restarting of the operation is

N/A
allowed if the appliance may continue to operate,
without causing any hazard to the user, from the
same point in its operating cycle at which the
voltage interruption or fluctuation occurred

22.ZE.9

N/A
energy sources

Such isolators are clearly identified, and N/A
they are capable of being locked if reconnection

N/A
endanger persons

After the energy source is disconnected, it is

N/A
possible to dissipate any energy remaining or
stored in the circuits of the appliance without risk to
persons

ZF ANNEX ZF (INFORMATIVE)

----

CRITERIA APPLIED FOR THE ALLOCATION OF PRODUCTS COVERED BY
STANDARDS IN THE EN 60335 SERIES UNDER LVD OR MD

List of standards under CENELEC/TC61 with the

P
allocation under the LVD (Low Voltage Directive) or

the MD (Machinery Directive) ............................... :

ZG ANNEX ZG (NORMATIVE)

----

UV APPLIANCES
The following modifications to this standard apply to

N/A
appliances having UV emitters

This annex is not applicable to appliances covered

N/A
by the scopes of IEC 60335-2-27, IEC 60335-2-59
or IEC 60335-2-109

7.12.ZG The instructions for appliances incorporating UVC

N/A
emitters include the substance of the following:
WARNING — This appliance contains a UV emitter.
Do not stare at the light source

32 For appliances incorporating UV emitters the

N/A
manufacturer delivers a declaration providing
evidence that the plastic material exposed to the
radiation is UV resistant

ZZ ANNEX ZZ (INFORMATIVE)

----

COVERAGE OF ESSENTIAL REQUIREMENTS OF EC DIRECTIVES

Description of the relation between this European

standard and the LVD (Low Voltage Directive,

Low Voltage Directive

2014/35/EU

P

2006/95/EC) and the MD (Machinery Directive,
2006/42/EC)

TRF No. IEC60335_2_98E

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 98 of 116 Report No. 160421073GZU-003

Photo documents:
Photos of ES071-1AE:

Modification 1: October 12, 2016

Front view

Water level mark

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 99 of 116 Report No. 160421073GZU-003

Modification 1: October 12, 2016

left side view (location of rating label)

Right side view

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]

Page 100 of 116 Report No. 160421073GZU-003

Modification 1: October 12, 2016

Rear view (water inlet hole)

DC socket

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch

Tel: [phone] Fax: [phone]