Honeywell ES800 operation manual

Air Coolers

Portable Evaporative Air Cooler
User Manual

Read and save these instructions before use

Scan here:

www.honeywellaircoolers.com

www.honeywellaircoolers.com
E-mail: [e-mail]

Model: ES800

PARTS DESCRIPTION

(1)

(2)

(3)

(4)

(9)

(5)

(6)

(7)

Remote Control

1)
Remote Control Receptor

2)
Control Panel

3)
Handle

4)
Louvers

5)

WARNING  READ AND SAVE THE AIR COOLER SAFETY & MAINTENANCE GUIDE AND USER
MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
DAMAGE AND/ OR IMPAIR ITS OPERATION AND VOID THE WARRANTY. IN CASE THERE IS
ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER
LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL
PREVAIL.

6)

7)

8)

9)

(8)

Water Level Indicator
with Light
Detachable Water Tank
Castors
Rear Grill

10)

11)

(10)

(11)

Power Cord Inlet
Power Adapter & Cord

USE & OPERATION

CONTROL PANEL

Icons on Display Screen

Power ON / OFF

Low Water Alarm

Swing

QuietSleep

TM

Cool

Timer

TurboBlast

Speed:

- Low

- Medium

TM

- High

- Auto

EN 1

USE & OPERATION (CONTINUED)

FUNCTION BUTTONS

POWER

Connect the power adapter to the cooler and to the electrical outlet. Press the button to turn
the unit on. The cooler will start automatically at low speed. To turn the unit off, press the button
again.

COOL

Press the button to select Cool mode.

Please make sure the water tank is filled with water above the minimum level mark. Pressing the
COOL indicator light on the display screen activates evaporative cooling. The water pump will
operate and you will feel the cooler air after the Honeycomb Cooling Media is completely wet.
Note: When the cooling function is switched OFF, the unit can still function in a fan only mode
(without evaporative cooling).

SPEED

Press the button repeatedly to change the fan speed between - - - .
The indicator light will show the selected speed:

(Low) (Medium) (High) (Auto)

When AUTO is selected, the wind speed will gradually decrease and increase between the
TurboBlast

QUIETSLEEP

Press the button to select either QuietSleep
minimizes wind speed for lower airflow. TurboBlast
airflow.

TIMER

Press the button until the desired time duration setting is selected. When the set time has
passed, the unit will automatically turn off (unit remains in Standby mode until power cord is
unplugged from electrical socket). The TIMER function allows you to program the unit for up to

7.5 hours of use.

SWING

Press the button until the SWING indicator light is illuminated on
the display screen. The louvers will begin to move left to right automatically.

TM

and QuietSleepTM fan speeds.

TM

/ TURBOBLAST

TM

TM

or TurboBlast

TM

TM

modes. QuietSleepTM mode

mode blasts wind at high speed for stronger

LOUVER

MOVEMENT

EN 2

USE & OPERATION (CONTINUED)

REMOTE CONTROL

Power
Fan Speed
Swing
Cool
Timer
QuietSleep
TurboBlast

Note:

The remote control requires a CR2032 (1 x 3V) coin type or equivalent battery for replacement.

•
Open the battery compartment at the back of the remote control and insert the battery inside.

•
Care must be taken to insert the batteries according to the correct polarity (+ / –) markings
shown inside the battery compartment.
Always point the remote control signal transmitter towards the unit when operating. Make sure

•
that the signal path is not obstructed.
Remove the batteries if the unit is not going to be used for an extended period of time.

•
Do not drop the remote control.

•
Do not mix different types of batteries such as alkaline, carbon-zinc, or rechargeable batteries.

•
Do not mix old and new batteries.

•
Do not recharge the battery.

•
Exhausted batteries are to be removed from the product and safely disposed of as per local

•
regulations.
Do not dispose of batteries in fire. Batteries may explode or leak.

•
WARNING: Caution for ingestion of the small battery. Keep away from children and animals.

: ON / OFF
: Low / Medium / High / Auto
: Controls the motion of the louvers
: Evaporative cooling on/off
: Controls the Timer function for automatic off

TM

: QuietSleep

/

TM

TM

/ TurboBlastTMmode

COOLER LOCATION

Make sure to position the air cooler correctly before you set up and start using the product.
Please refer to the COOLER LOCATION section of the separate Safety & Maintenance Guide.

EN 3

USE & OPERATION (CONTINUED)

FILLING WITH WATER & ICE

CAUTION:

Remove the power adapter and cord from the unit and the electrical outlet before emptying or
refilling the water tank. Wait for 2 minutes before removing the Water Tank to allow any excess
water in the Honeycomb Cooling Media to drip into the tank before removing it.

Note: After removing the tank, water from the Honeycombmay continue to drip and collect in the
tank compartment. Simply wipe dry with a clean, dry cloth.

Slide out the Water Tank. Refill the tank when water level is low. Do not fill
water above the "Max." water level mark to avoid water droplets collecting
on the louvers. Check the water level in the tank before running the COOL
function. The Low Water Alarm will sound when water is low. Running the
unit in COOL mode with inadequate water may cause pump failure.

If ice is available, you may add ice in the top ice compartment to
enhance the cooling performance.

Note: The water capacity refers to the total volume of water that can be
contained within the air cooler water tank and water distribution system.
The water capacity in the tank at the “Max.” indicator level may be lower
than the actual water capacity of the air cooler.

WARNING: Do not fill water tank with dirty water or salt water. This can damage the unit and
Honeycomb media.

WATER FILTER*

Some models are equipped with a water filter in the tank, which helps to
filter dust, hair and other particles from entering the water tank. Simply
pour water over the filter when refilling the tank.

To clean the water filter, simply push the bottom of the filter cup upwards
to release from the filter frame. Remove dust and hair from the filter sponge
and rinse under clean water. When clean, replace the sponge and secure
the filter cup back into the frame.

Front water fill door

for easy tank refill

Ice Compartment

Water
Filter

Filter Cup

AUTO-OFF SAFETY SYSTEM

This unit is equipped with an Auto-Off Safety System. When the water tank is detached from the
unit or if the tank is incorrectly positioned, the air cooler will turn off automatically. To restart
the cooler, the tank must be attached to the unit correctly.

*Applicable for models with water filter feature only.

EN 4

USE & OPERATION (CONTINUED)

LOW WATER ALARM*

The unit is equipped with a low water sensor. In Cooling Mode, when water in the tank is below the
minimum level, you will hear a beeping sound and the indicator light will flash continuously. The
unit will automatically pause evaporative cooling.

Refill the water tank to deactivate the alarm in cooling mode. First switch OFF the unit and
unplug from the power outlet. Fill the water tank with water above the minimum water level mark.
Plug in and switch ON again.

To deactivate the alarm and continue using the unit as a fan (without evaporative cooling), switch
the unit OFF and then ON again. The Low Water Alarm will not activate in Fan only mode. The Low
Water Alarm will sound again if the COOL function is activated while the water tank is still empty.

*Applicable for models with low water alarm feature only.

WATER LEVEL INDICATOR LIGHT

When the unit turns on, the water level indicator located at the front of the water tank will light up
to produce an elegant glow. This can be convenient as a night light during the night. This light will
remain on for as long as the air cooler is turned on.

CLEANING & DRAINING THE WATER TANK

If the cooler will not be used for a long period of time, please refer to the STORAGE &
MAINTENANCE GUIDELINES located in the separate Safety & Maintenance Guide.

WARNING:

Before cleaning the unit, switch the unit OFF and disconnect the power adapter from the unit and
electrical socket.

Slide out and empty the water tank.

•
Rinse the water tank with clean water.

•
Carefully remove the Water Tank Filter* (if your unit has this) from the tank. Remove dust and

•
hair from filter and then rinse with water until clean. Dry and replace the filter back into the
water tank.
Use a damp cloth to remove dirt and dust from the surface of the unit. Never use corrosive

•
elements or chemicals to clean this product.
When the product is not in use, store the unit in a dry place out of direct sunlight.

•

EN 5

*Applicable for models with water filter feature only.

USE & OPERATION (CONTINUED)

CLEANING THE CARBON DUST FILTER* AND HONEYCOMB COOLING MEDIA

WARNING:

Before cleaning the unit, switch the unit OFF and disconnect the power adapter from the unit and
electrical socket.

The appliance is supplied with a Carbon Dust Filter*

•

and Honeycomb Cooling Media.
The Carbon Dust Filter* and Honeycomb Cooling

•

Media are located inside the Rear Grill. See Figure 1
for instructions on how to remove them from the
unit for cleaning and maintenance.
Do not run the unit in COOL mode with stale water

•

in the tank. You must empty the water tank
and refill with fresh water, especially if the tank has
not been cleaned in a long time.
The cleaning frequency for the Honeycomb media

•

depends on local air and water conditions. In areas
where the mineral content of water is high, mineral
deposits may build up on the Honeycomb Cooling
Media and restrict air flow. Draining the water tank
and refilling with fresh water at least once a week
will help reduce mineral deposits. If mineral
deposits remain on the Honeycomb Cooling Media,
the media should be removed and washed under
fresh water. The media should be cleaned every two
months or sooner, depending on your needs.
For best results allow the Honeycomb Cooling

•

Media to dry after each use by turning off the cool
function 15 minutes before turning the unit off.

Figure 1:

Removing the Carbon Dust Filter*/ Honeycomb Cooling Media:

Carefully remove the rear grill from the unit.

1.
Remove the two band holders to release the carbon

2.
dust filter*.
Rinse the filter with clean water and let it dry before

3.
re-installing to the rear grill.
Pull out the Honeycomb Cooling Media. Slide down

4.
and remove the Honeycomb Frame.
Replace or clean media with water and a damp cloth as

5.
needed.

WARNING: DO NOT operate the Air Cooler when the

Rear Grill is removed from the Air Cooler, or if there is a
loose-fitting Rear Grill. Doing so can cause serious
injury or dangerous electrical shock.

*Applicable for models with Carbon Dust Filter only.

Honeycomb

Cooling Media

Honeycomb

Frame

Band

Holder

Carbon Dust

Filter*

Rear Grill

EN 6

TECHNICAL SPECIFICATIONS

Model

Cooler

Adaptor Input

Adaptor Output

Wattage

Water Tank Capacity

Cooling Media

Product Dimension

Net Weight

ELECTRICAL WIRING DIAGRAM

optional function:

water level

indicator LED

control PCBA

adapter

optional function :
tank swich

connector

100V-240V, 50 /60 hz, 1.5A

7 Litres / 1.8 Gallon

250 (W) x 316 (D) x 733 (H) mm

9.8 (W) x 12.4 (D) x 28.9 (H) in

water sense

water pump

power

input

ES800

DC 24V, 1.5A

24V, 1.5A, Class II

36 W

Honeycomb

5.3 kg / 11.7 lbs

Swing
motor

Fan motor

JMATEK Limited

Manulife Financial Centre,
Kwun Tong, Hong Kong
Phone: [phone]
Email: [e-mail]
Web: www.jmatek.com

Made in China
© 2016 JMATEK Limited. All rights reserved.
The Honeywell Trademark is used under license from
Honeywell International Inc.
Honeywell International Inc. makes no representations
or warranties with respect to this product.
This product is manufactured by JMATEK Limited.