Honeywell CADVR-04D, CADVR-08D, CADVR-16D User Manual

Download

Digital Video Recorder

CADVR-04D

CADVR-08D

CADVR-16D

User Manual

Welcome

Thank you for purchasing our DVR!

Please refer to this user’s manual for the installation and operation of HDDVR-7016.

Here you can find information about this series DVR features and functions, as well as a detailed menu tree.

Before installation and operation please read the following safeguards and warnings carefully!

Important Safeguards and Warnings

1. Electrical safety

All installation and operation here should conform to your local electrical

safety codes.

We assume no liability or responsibility for all the fires or electrical

shock caused by improper handling or installation.

2. Transportation security

Heavy stress, violent vibration or water splash are not allowed during

transportation, storage and installation.

3. Installation

All the examination and repair work should be done by the qualified

service engineers.

We are not liable for any problems caused by unauthorized

modifications or attempted repair.

4. Qualified engineers needed

All the examination and repair work should be done by the qualified

service engineers.

We are not liable for any problems caused by unauthorized

modifications or attempted repair.

5. Environment

The DVR should be installed in a cool, dry place away from direct

sunlight, inflammable, explosive substances and etc.

6. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the

components are included.

Contact your local retailer ASAP if something is broken in your package.

7. Lithium battery

Improper battery use may result in fire, explosion, or personal injury!

When replace the battery, please make sure you are using the same

model!

Contents

User Manual............................................................................................................................. 1

Welcome....................................................................................................................... 1

Important Safeguards and Warnings ............................................................................ 1

1 FEATURES AND SPECIFICATIONS ................................................................................. 7

Overview....................................................................................................................... 7

Features ....................................................................................................................... 8

Specifications................................................................................................................ 1

2 Overview and Controls........................................................................................................ 5

Front Panel ................................................................................................................... 5

Rear Panel.................................................................................................................... 7

Connection Sample ...................................................................................................... 9

Remote Control............................................................................................................. 9

Mouse Control ............................................................................................................ 11

Virtual Keyboard & Front Panel .................................................................................. 13

Virtual Keyboard............................................................................................................ 13

Front Panel..................................................................................................................... 13

3 Installation and Connections............................................................................................. 14

Check Unpacked DVR................................................................................................ 14

About Front Panel and Real Panel ............................................................................. 14

HDD Installation.......................................................................................................... 15

Rack Installation ......................................................................................................... 16

Connecting Power Supply .......................................................................................... 17

Connecting Video Input and Output Devices .............................................................. 17

Connecting Video Input ................................................................................................ 17

Connecting Video Output ............................................................................................. 18

Connecting Audio Input & Output, Bidirectional Audio................................................ 19

Audio Input ..................................................................................................................... 19

Audio Output .................................................................................................................. 20

Alarm Input and Output Connection............................................................................ 21

Alarm Input and Output Details ................................................................................... 23

Alarm Input Port ............................................................................................................ 24

Alarm Output Port ......................................................................................................... 25

RS232......................................................................................................................... 26

RS485......................................................................................................................... 26

Other Interfaces.......................................................................................................... 27

4 Overview of Navigation and Controls................................................................................ 28

Login ............................................................................................................................... 28

Main Menu ..................................................................................................................... 30

Logout ............................................................................................................................. 31

Auto Resume after Power Failure............................................................................... 31

Replace Button Battery ................................................................................................ 32

Manual Record ........................................................................................................... 32

Live Viewing................................................................................................................... 32

Manual record................................................................................................................ 33

Search & Playback ..................................................................................................... 36

Schedule..................................................................................................................... 41

Schedule Menu.............................................................................................................. 41

Snapshot ........................................................................................................................ 44

Image FTP ..................................................................................................................... 47

Snapshot Disk (For special series only)..................................................................... 48

Detect ......................................................................................................................... 50

Go to Detect Menu........................................................................................................ 50

Motion Detect................................................................................................................. 50

Video Loss ..................................................................................................................... 54

Camera Masking ........................................................................................................... 54

Alarm Setup and Alarm Activation .............................................................................. 55

Go to alarm setup interface ......................................................................................... 55

Alarm setup.................................................................................................................... 56

Backup........................................................................................................................ 58

Detect Device ................................................................................................................ 58

Backup............................................................................................................................ 59

PTZ Control and Color Setup ..................................................................................... 61

Cable Connection.......................................................................................................... 61

PTZ Setup ...................................................................................................................... 62

Preset/ Patrol/Pattern/Scan ........................................................................................ 64

Preset Setup .................................................................................................................. 66

Activate Preset .............................................................................................................. 67

Patrol setup (Tour Setup)............................................................................................. 67

Activate Patrol (tour) ..................................................................................................... 68

Pattern Setup................................................................................................................. 68

Activate Pattern Function............................................................................................. 69

Auto Scan Setup ........................................................................................................... 69

Activate Auto Scan........................................................................................................ 70

Flip.............................................................................................................................. 70

5 Understanding of Menu Operations and Controls............................................................. 72

Menu Tree .................................................................................................................. 72

Main Menu.................................................................................................................. 74

Setting ........................................................................................................................ 74

General ........................................................................................................................... 75

Encode............................................................................................................................ 77

Schedule......................................................................................................................... 80

RS232............................................................................................................................. 80

Network........................................................................................................................... 81

Alarm............................................................................................................................... 95

Detect.............................................................................................................................. 95

Pan/Tilt/Zoom ................................................................................................................ 95

Display ............................................................................................................................ 96

Default ............................................................................................................................ 99

Search ...................................................................................................................... 100

Advanced.................................................................................................................. 100

HDD Management ...................................................................................................... 101

Abnormity ..................................................................................................................... 106

Alarm Output................................................................................................................ 107

Manual Record ............................................................................................................ 108

Account......................................................................................................................... 108

Auto Maintain............................................................................................................... 113

TV Adjust...................................................................................................................... 114

Video Matrix ................................................................................................................. 114

Card Overlay................................................................................................................ 115

Config File Backup...................................................................................................... 119

Information................................................................................................................ 119

HDD Information.......................................................................................................... 120

BPS ............................................................................................................................... 121

Log ................................................................................................................................ 122

Version.......................................................................................................................... 123

Online Users ................................................................................................................ 124

Shutdown.................................................................................................................. 125

6 About Auxiliary Menu ...................................................................................................... 127

Go to Pan/Tilt/Zoom Menu........................................................................................ 127

Preset /Patrol / Pattern /Border Function ................................................................ 129

Preset Setup ................................................................................................................ 130

Activate Preset ............................................................................................................ 131

Patrol Setup ................................................................................................................. 131

Activate Patrol.............................................................................................................. 131

Pattern Setup............................................................................................................... 131

Activate Pattern Function........................................................................................... 132

Border Setup................................................................................................................ 132

Activate Border Function............................................................................................ 133

Flip................................................................................................................................. 133

7 WEB CLIENT OPERATION............................................................................................ 135

Network Connection ................................................................................................. 135

Login......................................................................................................................... 135

Real-time Monitor........................................................................................................ 139

PTZ................................................................................................................................ 141

Color.............................................................................................................................. 145

Picture Path and Record Path................................................................................... 146

Configure .................................................................................................................. 147

System Information..................................................................................................... 147

System Configuration ................................................................................................. 150

Advanced ..................................................................................................................... 176

Additional Function ..................................................................................................... 183

Search ...................................................................................................................... 186

Alarm ........................................................................................................................ 191

About ........................................................................................................................ 193

Log out...................................................................................................................... 193

Un-install Web Control.............................................................................................. 194

8 Professional Surveillance System................................................................................... 195

9 FAQ ................................................................................................................................ 196

Appendix A HDD Capacity Calculation.................................................................. 202

Appendix B Compatible Backup Device List......................................................... 204

APPENDIX C Compatible CD/DVD Device List........................................................ 208

Appendix D Compatible Displayer List .................................................................. 209

Appendix E Compatible Switcher List.................................................................... 210

Appendix F Compatible Wireless Mouse List ........................................................ 211

Appendix G Earthing ............................................................................................. 211

Appendix H Toxic or Hazardous Materials or Elements................................................ 1

Figures

Figure 2- 1 The Front Panel of CADVR-04D.........................................................................5

Figure 2- 2 The Rear Panel of CADVR-04D..........................................................................8

Figure 2- 3 Device Connection..............................................................................................9

Figure 2- 4 Remote Controller............................................................................................ 10

Figure 3- 1 Connecting Video Input................................................................................... 18

Figure 3- 2 Connecting Video Output................................................................................ 19

Figure 3- 3 Audio Input ....................................................................................................... 20

Figure 3- 4 Audio Output .................................................................................................... 20

Figure 3- 5 Alarm Input and Output Connection.............................................................. 21

Figure 3- 6. Alarm Input and Output.................................................................................. 23

Figure 3- 7 Alarm Input ....................................................................................................... 24

Figure 3- 8 Other Interfaces ............................................................................................... 27

Figure 4-1 Startup Wizard................................................................................................... 29

Figure 4-2 Menu Login........................................................................................................ 30

Figure 4-3 Main Menu.......................................................................................................... 30

Figure 4-4 Logout Menu...................................................................................................... 31

Figure 4-5 Options for Logout ........................................................................................... 31

Figure 4-6 Preview Zoom Function ................................................................................... 33

Figure 4-7 Recording Control Menu .................................................................................. 34

Figure 4-8 Different Status of Manual Record.................................................................. 34

Figure 4-9 Automatic Recording in All Channels ............................................................ 35

Figure 4-10 Start Manual Record in All Channels............................................................ 35

Figure 4-11 Stop Recording in All Channels .................................................................... 36

Figure 4-12 Record Search Menu ...................................................................................... 37

Figure 4-13 Schedule Setting............................................................................................. 42

Figure 4-14 redundancy setup ........................................................................................... 44

Figure 4-15 Schedule Snapshot Setting ........................................................................... 45

Figure 4-16 Activation Snapshot Setting.......................................................................... 46

Figure 4-17 Image FTP Stting............................................................................................. 48

Figure 4-18 Snapshot Disk Setting.................................................................................... 48

Figure 4-19 Search Image Via Web.................................................................................... 49

Figure 4-20 Motion Detect Setting ..................................................................................... 52

Figure 4-21 Motion Detection Zone Setting...................................................................... 52

Figure 4-22 PTZ Activation Setting.................................................................................... 53

Figure 4-23 Armed Period Setting ..................................................................................... 53

Figure 4-24 Business Day and Non-Business Day Setting............................................. 53

Figure 4-25 Video Loss Setting.......................................................................................... 54

Figure 4-26 Camera Masking Setting ................................................................................ 55

Figure 4-27 Local Alarm Setting ........................................................................................ 57

Figure 4-28 PTZ Activation Settings.................................................................................. 57

Figure 4-29 Period Setting.................................................................................................. 58

Figure 4-30 Business Days and Non-Business Days Settings....................................... 58

Figure 4-31 Device Detection Menu of Backup................................................................ 59

Figure 4-32 Backup Menu with Search Results ............................................................... 60

Figure 4-33 Select The Type............................................................................................... 60

Figure 4-34 PTZ Setting ...................................................................................................... 62

Figure 4-35 Context Menu .................................................................................................. 63

Figure 4-36 PTZ Control Menu ........................................................................................... 64

Figure 4-37 Direction Arrows ............................................................................................. 64

Figure 4-38 PTZ Setup Menu.............................................................................................. 65

Figure 4-39 PTZ Function Menu......................................................................................... 66

Figure 4-40 Preset Setting.................................................................................................. 67

Figure 4-41 Tour Setting..................................................................................................... 68

Figure 4-42 Pattern Setting ................................................................................................ 69

Figure 4-43 Auto Scan Setting ........................................................................................... 70

Figure 4-44 Auxiliary Setting.............................................................................................. 71

Figure 5-1 Main Menu.......................................................................................................... 74

Figure 5-2 Setting ................................................................................................................ 75

Figure 5-3 General Setting.................................................................................................. 77

Figure 5-4 DST Setup Menu (Week)................................................................................... 77

Figure 5-5 DST setup menu (Date) .................................................................................... 77

Figure 5-6 Encode Menu..................................................................................................... 79

Figure 5-7 Encode Menu..................................................................................................... 79

Figure 5-8 RS232 Setup Menu............................................................................................ 81

Figure 5-9 Network Setup Menu ........................................................................................ 82

Figure 5-10 Advanced Settings.......................................................................................... 83

Figure 5-11 IP Filter Menu .................................................................................................. 83

Figure 5-12 NTP Setup Menu ............................................................................................. 85

Figure 5-13 Multiple Cast Setup Menu .............................................................................. 86

Figure 5-14 PPPOE Setup Menu ........................................................................................ 87

Figure 5-15 DDNS Setup Menu .......................................................................................... 88

Figure 5-16 UPNP Menu...................................................................................................... 90

Figure 5-17 Port Info Menu................................................................................................. 90

Figure 5-18 Email Setup Menu ........................................................................................... 92

Figure 5-19 Mail Test Info ................................................................................................... 92

Figure 5-20 FTP Server Setup Menu.................................................................................. 93

Figure 5-21 FTP Login Window.......................................................................................... 93

Figure 5-22 FTP Setup Menu.............................................................................................. 94

Figure 5-23 FTP Test Info ................................................................................................... 95

Figure 5-24 PTZ Setup Menu.............................................................................................. 96

Figure 5-25 The Display Setup Menu ................................................................................ 98

Figure 5-26 Channel Name Setup Menu............................................................................ 98

Figure 5-27 The Sample of Tour Mode .............................................................................. 99

Figure 5-28 Default Setup Menu ...................................................................................... 100

Figure 5-29 Advanced Menu ............................................................................................ 101

Figure 5-30 HDD Management Setup Menu.................................................................... 102

Figure 5-31 Abnormity Setup Menu................................................................................. 102

Figure 5-32 Different HDD Group Setting Menu............................................................. 104

Figure 5-33 Same HDD Group Setting Menu .................................................................. 105

Figure 5-34 HDD Group 1 Channel Setting..................................................................... 106

Figure 5-35 HDD Group 2 Channel Setting..................................................................... 106

Figure 5-36 Sample of No Disk Abnormity ..................................................................... 107

Figure 5-37 Alarm Output Setup Menu............................................................................ 108

Figure 5-38 Account Management Menu ........................................................................ 110

Figure 5-39 Modify Password .......................................................................................... 111

Figure 5-40 Add Group ..................................................................................................... 112

Figure 5-41 Add User ........................................................................................................ 113

Figure 5-42 Auto Maintain Setup Menu........................................................................... 113

Figure 5-43 TV Adjust Menu............................................................................................. 114

Figure 5-44 Video Matrix Menu ........................................................................................ 115

Figure 5-45 Text Overlay(COM Type) .............................................................................. 116

Figure 5-46 Text Overlay(Network Type) ........................................................................ 117

Figure 5-47 ATM/POS........................................................................................................ 118

Figure 5-48 Data Format ................................................................................................... 118

Figure 5-49 Config File Backup ....................................................................................... 119

Figure 5-50 Info Menu ....................................................................................................... 120

Figure 5-51 HDD Info Menu .............................................................................................. 121

Figure 5-52 BPS Display Menu ........................................................................................ 121

Figure 5-53 Log Search Menu .......................................................................................... 122

Figure 5-54 Log Details..................................................................................................... 123

Figure 5-55 Version Menu................................................................................................. 124

Figure 5-56 Online Users Menu ....................................................................................... 125

Figure 5-57 Shutdown Menu ............................................................................................ 126

Figure 6- 1 Context Menu ................................................................................................. 127

Figure 6- 2 PTZ Control Menu .......................................................................................... 128

Figure 6- 3 Direction Arrows ............................................................................................ 128

Figure 6- 4 PTZ Setup Menu............................................................................................. 129

Figure 6- 5 PTZ Function Menu........................................................................................ 130

Figure 6- 6 Preset Setting................................................................................................. 130

Figure 6- 7 Tour Setting.................................................................................................... 131

Figure 6- 8 Pattern Setting................................................................................................ 132

Figure 6- 9 Auto Scan Setting .......................................................................................... 133

Figure 6- 10 Auxiliary Setting........................................................................................... 134

Figure 7- 1 Sample of IE Login......................................................................................... 136

Figure 7- 2 Internet Options Window .............................................................................. 136

Figure 7- 3 Web Login Window........................................................................................ 137

Figure 7- 4 Window Switch Menu .................................................................................... 138

Figure 7- 5 Main Menu of Web Client .............................................................................. 139

Figure 7- 6 Status Information ......................................................................................... 139

Figure 7- 7 Control Setup ................................................................................................. 139

Figure 7- 8 Switch between the Main Stream and Extra Stream .................................. 140

Figure 7- 9 Selection Menu of Local Play File ................................................................ 141

Figure 7- 10 PTZ Control Menu ........................................................................................ 142

Figure 7- 11 PTZ Setup Menu........................................................................................... 143

Figure 7- 12 Assistant Setup Menu ................................................................................. 145

Figure 7- 13 Color Setup Menu ........................................................................................ 145

Figure 7- 14 More Setup Menu ......................................................................................... 146

Figure 7- 15 Path Setup Menu (for Picture) .................................................................... 146

Figure 7- 16 Path Setup Menu (for Record) .................................................................... 147

Figure 7- 17 Reboot Dialog............................................................................................... 147

Figure 7- 18 Version Information Menu........................................................................... 148

Figure 7- 19 HDD Information Menu ................................................................................ 148

Figure 7- 20 Log Information Menu ................................................................................. 149

Figure 7- 21 Log Backup Menu ........................................................................................ 149

Figure 7- 22 General Setup Menu .................................................................................... 150

Figure 7- 23 DST Setup Menu (Date) ............................................................................... 151

Figure 7- 24 DST Setup Menu (Week).............................................................................. 151

Figure 7- 25 Encode Menu................................................................................................ 153

Figure 7- 26 Color Setting Menu ...................................................................................... 153

Figure 7- 27 Copy-To Menu .............................................................................................. 156

Figure 7- 28 Schedule Setup Menu.................................................................................. 156

Figure 7- 29 Date and Time Setup Menu......................................................................... 157

Figure 7- 30 RS232 Setup Menu....................................................................................... 158

Figure 7- 31 Network Setup Menu ................................................................................... 159

Figure 7- 32 Email Setup Menu ........................................................................................ 161

Figure 7- 33 DDNS Setup Menu ....................................................................................... 162

Figure 7- 34 NAS Setup Menu .......................................................................................... 163

Figure 7- 35 NTP Setup Menu .......................................................................................... 164

Figure 7- 36 Alarm Setup Menu ....................................................................................... 166

Figure 7- 37 Advanced Setup........................................................................................... 167

Figure 7- 38 UPNP Setup .................................................................................................. 168

Figure 7- 39 Alarm Setup Menu ....................................................................................... 168

Figure 7- 40 PTZ Setting ................................................................................................... 169

Figure 7- 41 The Detection Setup Menu.......................................................................... 171

Figure 7- 42 The Detection Zone Setup........................................................................... 171

Figure 7- 43 PTZ Setup Menu........................................................................................... 174

Figure 7- 44 Default Setup Menu ..................................................................................... 176

Figure 7- 45 HDD Management Menu.............................................................................. 177

Figure 7- 46 Alarm I/O Config Menu ................................................................................ 178

Figure 7- 47 Record Control Menu .................................................................................. 179

Figure 7- 48 Account Management Menu ....................................................................... 180

Figure 7- 49 Auto Maintenance Menu.............................................................................. 180

Figure 7- 50 Snapshot....................................................................................................... 181

Figure 7- 51 Abnormity Setup Menu................................................................................ 182

Figure 7- 52 Matrix Config ................................................................................................ 183

Figure 7- 53 DNS................................................................................................................ 184

Figure 7- 54 CARD OVERLAY .......................................................................................... 185

Figure 7- 55 Auto Register ............................................................................................... 185

Figure 7- 56 Record Search Menu ................................................................................... 187

Figure 7- 57 Record Save Menu....................................................................................... 187

Figure 7- 58 Record Search Menu (Saving).................................................................... 188

Figure 7- 59 Message Box after Download Completed ................................................. 188

Figure 7- 60 Playback Menu ............................................................................................. 191

Figure 7- 61 Alarm Function Menu .................................................................................. 192

Figure 7- 62 Web Client Information................................................................................ 193

Figure 7- 63 Logout Interface........................................................................................... 194

1 FEATURES AND SPECIFICATIONS

Overview

This series product is an excellent digital monitor product designed for

security field. It adopts embedded Linux OS to maintain reliable

operation. Popular H.264 compression algorithm and G.711 audio

compression technology realize high quality, low bit stream. Unique

frame by frame play function is suitable for detail analysis. It has various

functions such as record, playback, monitor at the same time and can

guarantee audio video synchronization. This series product has

advanced technology and strong network data transmission function.

This series device adopts embedded design to achieve high security

and reliability. It can work in the local end, and at the same time, when

connecting it to the professional surveillance software (CADVR-CS), it

can connect to security network to realize strong network and remote

monitor function.

This series product can be widely used in various areas such as

banking, telecommunication, electric power, interrogation, transportation,

intelligent resident zone, factory, warehouse, resources, and water

conservancy.

Features

This series product has the following features:

z Real-time monitor

It has analog output port, VGA port and HDMI port. You can use

monitor or displayer to realize surveillance function.

System supports TV/VGA/HDMI output at the same time.

z Storage function

Special data format to guarantee data security and can avoid vicious

data modification.

z Compression format

Support multiple-channel audio and video. An independent hardware

decodes the audio and video signal from each channel to maintain

video and audio synchronization.

z Backup function

Support backup operation via USB port (such as flash disk, portable

HDD, burner).

Client-end user can download the file to local HDD to backup via

network.

z Record playback function

Support each channel real-time record independently, and at the same

time it can support search, forward play, network monitor, record search,

download and etc.

Support various playback modes: slow play, fast play, backward play

and frame by frame play.

Support time title overlay so that you can view event accurate occurred

time

Support specified zone enlargement.

z Network operation

Support network remote real-time monitor, remote record search and

remote PTZ control.

z Alarm activation function

Several relay alarm outputs to realize alarm activation and on-site light

control.

The alarm input port and output has the protection circuit to guarantee

device safety.

z Communication port

RS485 port can realize alarm input and PTZ control.

RS232 port can connect to keyboard to realize central control, and can

also connect to PC COM to upgrade system and realize maintenance,

and matrix control.

Standard Ethernet port can realize network access function.

z PTZ control

Support PTZ decoder via RS485.

Support various decode protocols to allow the PTZ to control the speed

dome.

z Intelligent operation

Mouse operation function

In the menu, support copy and paste setup function

z UPnP

It is to establish the mapping relationship between the LAN and the

WAN via the UPnP protocol.

Slight function differences may be found due to different series.

Specifications

Parameter

CADVR-04D CADVR-08D CADVR-16D

Main Processor

High-performance industrial embedded micro controller

OS Embedded LINUX

System Resources

Multiplex operations: Multiple-channel record, multiple-channel playback and network operation simultaneously

Interface User-friendly graphical user interface

Input Devices Front panel, USB mouse, remote control

Input Method

Arabic number, English character, donation and extension Chinese (optional)

System

Shortcut Function

Copy/paste operation, USB mouse right-key shortcut menu, double click USB mouse to switch screen.

Video Compression

H.264

Compression Standard

Audio Compression

G.711A

Video Input

4-CH composite video input: (NTSC/PAL) BNC (1.0V

P- P,

75Ω)

8-CH composite video input: (NTSC/PAL) BNC (1.0VB

P- P,

75Ω)

16-CH composite video input: (NTSC/PAL) BNC (1.0VB

P- P,

75Ω)

Video Output

1-ch PAL/NTSC, BNC (1.0VP- P, 75Ω) composite video signal output. 1-ch VGA output. 1-ch HDMI output. 1-ch matrix output.

Support TV/VGA/HDMI video output at the same time. Video Standard

PAL (625 line, 50f/s), NTSC (525 line, 60f/s)

Record Speed

Real-time Mode: PAL 1f/s to 25f/s per channel and NTSC 1f/s to 30f/s per

channel

Video Partition 1/4 windows(Optional) 1/4/8/9 windows 1/4/8/9 /16 windows Monitor

Touring

Support monitor tour functions such as alarm, motion detection, and

schedule auto control.

Video monitor

Resolution (PAL/NTSC)

PAL/NTSC

Real-time monitor：

D1 704×576/704×480

Playback channel 1/16：

D1 704×576/704×480

CIF 352×288/ 352×240

QCIF 176×144/176×120

Support dual streams.

Extra stream resolution:

CIF 352×288/ 352×240

QCIF 176×144/176×120 Image Quality 6-level image quality (Adjustable) Privacy mask Support one privacy mask of user-defined size in full screen.

Support max 4 zones. Image Information

Channel information, time information and privacy mask zone.

TV Adjust Adjust TV output zone suitable to anamorphic video.

Channel Lock Cover secret channel with black screen though system is encoding

normally.

Screen-lock function to prevent unauthorized user seeing secret video. Channel Information

Channel name, recording status, screen lock status, video loss status and

motion detection status are shown on the bottom left of display screen. Color Configuration

Hue, brightness, contrast, saturation and gain setup for each channel.

Audio Input

4-ch 200-2000mv

10KΩ(BNC)

8-ch 200-2000mv 10KΩ(BNC)

16-ch 200-2000mv 10KΩ (BNC)

Audio Output 1-ch audio output 200-3000mv 5KΩ(BNC)

Audio

Bidirectional Audio

1-ch audio talk input 200-3000mv 10KΩ（BNC）

1-ch audio talk output 200-3000mv 5KΩ(BNC)

Hard Disk 8 built-in SATA port. Support 8 HDDs.

Hard disk

Hard Disk Occupation

Audio：PCM 28.8MByte/h

Video：56-900MByte/h

Recording Mode

Manual recording, motion detection recording, schedule recording and

alarm recording

Priority: Manual recording> alarm recording>motion detection

recording>schedule recording. Recording Length

1 to 120 minutes single record duration (Default setup is 60 minutes)

Playback Repeat Way

When hard disk is full, system can overwrite previous video file.

Record Search

Various search engines such as time, type and channel.

Record and playback

Playback Mode

Various fast play, slow play speeds, manual frame by frame playback and

reverse play mode.

Various File Switch Ways

Can switch to previous or next file or any file in current play list.

Can switch to file on other channel of the same time. (If there is a file)

Support file continuous play, when a file is end system auto plays the next

file in the current channel Multi-channel Playback

There is 1/4/9/16-channel playback mode.

(It may vary due to different series.)

Window Zoom

Switch between self-adaptive screen/full screen when playback

Partial Enlargement

When in one-window full-screen playback mode, you can select any zone

to activate partial enlargement function.

HDD backup

Support peripheral USB backup device. (Flash disk, portable disk, USB

burner and etc.)

Support peripheral eSATA backup device.

Backup function

Backup Mode

Support network download and backup

View monitor channel remotely.

DVR configuration through client-end and web browser

Upgrade via client or browser to realize remote maintenance.

View alarm information such as external alarm, motion detection and video

loss via client.

Support network PTZ lens control

File download backup and playback

Multiple devices share information via corresponding software such as

professional surveillance software (CADVR-CS)

Duplex transparent COM

Network alarm input and output

Network Function

Network control

Bidirectional audio. Motion Detection

Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones.

Various sensitivity levels.

Alarm can activate record or external alarm or screen message prompt. Video Loss Alarm can activate external alarm or screen message prompt. External Alarm

Support record activation function or activate external alarm or screen

message in specified period. Manual Alarm Control

Enable or disable alarm input channel

Support analog alarm signal to specific alarm output channel.

Alarm Input

4-ch alarm input（You

can set normal open or

normal close type to

select the alarm

type. ）

8-ch alarm input （ You can set normal open or normal close type to select the alarm type. ）

16-ch alarm input （You can set normal open or normal close type to select the alarm type. ）

Alarm Output 6-channel relay output, including one controllable DC +12V output port.

Motion Detection and Alarm

Alarm Relay 30V DC 2A，125V AC 1A（activation alarm ） USB Interface 3 USB 2.0 ports. Network

connection

RJ45 10M/100M/1000M self-adaptable Ethernet port

Interface

RS485

PTZ control port

Support various PTZ control protocols.

RS232

Ordinary COM (Debug),keyboard connection and transparent serial

port(COM input and output via network ) Hard Disk Information

Display HDD current status

Data Stream Statistics

Data stream statistics for each channel (in wave mode)

Log statistics

Backup to 1024 log files.

Support various search engines such as time and type.

Version

Display version information: channel amount, alarm input and output

amount, system version and release date.

System Information

On-line user Display current on-line user

Multi-lever user management; various management modes

Integrated management for local user, serial port user and network user.

Configurable user power.

User Management

Support user /group and its corresponding rights modification.

No limit to the user or group amount.

Password modification

Administrator can modify other user’s password.

User Management

Password Authentication

Account lock strategy

Five times login failure in thirty minutes may result in account lock.

Upgrade Web browser, client-end and update tool.

Password login protection to guarantee safety

User-friendly interface when login. Provide the following options: Logout

/shutdown/ restart.

Right authentication when shut down to make sure only those proper

people can turn off DVR Power AC90~264V 50+2% Hz （Max 75W） Power

Consumption

25W (Exclude HDD)

Working Temperature

0℃－＋55℃

Working Humidity

10%－90%

Air Pressure 86kpa－106kpa

Dimension 2U standard industrial case. 440(W) x460 (D) x89mm(H)

Weight 6.5-7.5KG(Exclude HDD)

General Parameter

Installation Mode

Desktop/rack installation

2 Overview and Controls

This section provides information about front panel and rear panel.

When you install this series DVR for the first time, please refer to this

part first.

Front Panel

The front panel is shown as in 667HFigure 2- 1

Figure 2- 1 The Front Panel of CADVR-04D

Please refer to the following sheet for front panel button information.

Name Icon Function

Power button

Power button, press this button for three seconds to boot up or shut down DVR.

USB port

To connect USB storage device, USB mouse.

Input numbers and letters, press “10” to input 0

In live view, display a corresponding channel in full screen

Numeric keys

1-16 A-Z

In playback, switch to records of the corresponding channel

Up Down

S T

Activate current control, modify setup, and then move up and down.

Increase/decrease numeral.

Assistant function such as PTZ menu.

Shift current activated control,

Left/2 Right/3

W X

During playback, click these buttons to control playback bar.

Confirm current operation

Go to default button

Enter

ENTER

Go to menu

Go to previous menu, or cancel current operation.

ESC

During playback, click it to restore real-time monitor mode.

Shift

In textbox, click this button to switch between numeral, English (Small/Capitalized), donation and etc.

One-window monitor mode, click this button to display assistant function: PTZ control and image color.

In PTZ menu, shift PTZ control menu.

Backspace function: in numeral control or text control, it can delete the previous character before the cursor.

In motion detection setup, work with Fn and direction keys to realize setup.

In preview mode, click it for three seconds to switch between TV.VGA. For HD1 series DVR, there are three modes: TV, VGA, VGA_LCD (60Hz LED output).

In text mode, click it to switch between numeral, English character(small/capitalized) and etc.

Assistant

Realize other special functions.

Full Screen

FULL SCRN

Switch live view window layout to single channel full screen display.

Layout Switch

MULT

Switch live view window layout between single-channel and multiple-channel display.

Record

REC

Manually stop/start recording, working with direction keys

or numeral keys to select the recording channel.

Play/Pause f

In live view, press this key to enter Search interface. Login dialog may appear if user is not logged in.

In normal playback click this button to pause playback

In reverse playback or pause mode, click this button to resume normal playback.

In live view, press this key to enter Search interface.

Reverse/Pause

W

In normal playback or pause mode, click this button to reverse playback

In reverse playback, click this button to pause playback.

Fast play



Various fast speeds and normal playback.

Slow play

Multiple slow play speeds or normal playback.

Play Next

f│

In playback mode, playback the next video

In menu setup, go to the bottom of the dropdown list.

Play previous

│W

In playback mode, playback the previous video

Shuttle (outer ring)

In live view, it works as left/right direction key.

In playback, counter clockwise to forward and clock wise to backward.

Jog (inner dial)

Up/down direction key.

In playback, turn the inner dial to do frame by frame playback when normal playback is paused.

RC indicator

ACT

Indicates if the DVR is active for remote control.

Power indicator

POWER

Indicates if the DVR is powered up

Channel indicator

1-16

Indicates whether the system is recording or not. It turns on when the system is recording.

IR Receiver

Receives the signal from the remote controller.

HDD indicator

HDD

Indicates if the HDD is error or full.

Status indicator

STATUS

Indicates if the DVR is running.

Rear Panel

This series DVR rear panel is shown as below. See 668HFigure 2- 2.

Figure 2- 2 The Rear Panel of CADVR-04D

Please refer to the following sheet for detailed information.

No. Description

1 GND port 2 Power input port 3 Power button 4 Fan 5 DB25 port ( 5th to 16th-channel audio input port) 6 1st to 4th-channel audio input 7 Loop video output 8 Video input 9 Video CVBS output 10 Matrix video output 11 Audio output 12 Bidirectional talk input port

13 Bidirectional talk output port

14 Alarm input/Alarm output/RS485 port HDMI port 15 Video VGA output

16 HDMI port

17 Video CVBS output RS232 port

18 Video matrix output eSATA port 19 USB port 20 Network port

When connect the Ethernet port, please use crossover cable to connect

the PC and use the straight cable to connect to the switcher or router.

Connection Sample

Please refer to669HFigure 2- 3 for connection sample.

Figure 2- 3 Device Connection

Remote Control

The remote control interface is shown as in 670HFigure 2- 4

Please note remote control is not our standard accessory and it is not

included in the accessory bag.

Figure 2- 4 Remote Controller

Please refer to the following sheet for detailed information.

No. Function

1 Record search

2 Multiple-window switch

3 0-9 number keys

4 ESC, Cancel

5 Reserved, not effective for HD-DVR-7016

Confirm /menu key

7 Direction keys

8 Auxiliary function key

9 Remote address switch

10 Previous

11 Backward playback

12 Slow play

13 Play/Pause

14 Fast play

15 Next

16 Record

Mouse Control

System pops up password input dialogue box if you have not logged in. In real-time monitor mode, you can go to the main menu. When you have selected one menu item, left click mouse to view menu content. Implement the control operation. Modify checkbox or motion detection status. Click combo box to pop up drop down list

Left click mouse

In input box, you can select input methods. Left click the corresponding button on the panel you can input numeral/English

character (small/capitalized). Here ← stands for backspace button. ＿ stands for space button.

In English input mode: _stands for input a backspace icon and ← stands for deleting the previous character.

In numeral input mode: _ stands for clear and ← stands for deleting the previous numeral.

When input special sign, you can click corresponding numeral in the front panel to input. For example, click numeral 1 you can input“/” , or you can click the numeral in the on-screen keyboard directly.

Implement special control operation such as double click one item in the file list to playback the video.

Double left click mouse

In multiple-window mode, double left click one channel to view in full-window. Double left click current video again to go back to previous multiplewindow mode. In real-time monitor mode, pops up shortcut menu: one-window, fourwindow, nine-window and sixteen-window, Pan/Tilt/Zoom, color setting, search, record, alarm input, alarm output, main menu. Among which, Pan/Tilt/Zoom and color setting applies for current selected channel. If you are in multiple-window mode, system automatically switches to the corresponding channel.

Right click mouse

Exit current menu without saving the modification. In numeral input box: Increase or decrease numeral value. Switch the items in the check box.

Press middle button

Page up or page down Move mouse

Select current control or move control

Select motion detection zone Drag mouse

Select privacy mask zone.

Virtual Keyboard & Front Panel

Virtual Keyboard

The system supports two input methods: numeral input and English

character (small and capitalized) input.

Move the cursor to the text column, the text is shown as blue, input

button pops up on the right. Click that button to switch between numeral

input and English input (capitalized and small), Use > or < to shift

between small character and capitalized character.

Front Panel

Move the cursor to the text column. Click Fn key and use direction keys

to select number you wanted. Please click enter button to input.

3 Installation and Connections

Note

All the installation and operations here should conform to your local electrical safety rules

Check Unpacked DVR

When you receive the DVR from the forwarding agent, please check

whether there is any visible damage. The protective materials used for

the package of the DVR can protect most accidental clashes during

transportation. Then you can open the box to check the accessories.

Please check the items in accordance with the list on the warranty card

(Remote control is optional). Finally you can remove the protective film

of the DVR.

Note

Remote control is not a standard accessory and it is not included in the accessory bag.

About Front Panel and Real Panel

The model label in the front panel is very important; please check

according to your purchase order.

The label in the rear panel is very important too. Usually we need you to

represent the serial number when we provide the service after sales.

HDD Installation

This series DVR max supports 8 SATA HDDs. Please use HDD of

7200rpm or higher. It has no requirement for HDD capacity.

You can refer to the appendix for recommended HDD brand.

Please follow the instructions below to install hard disk.

1. Loosen the screws and remove the the upper cover.

2. Remove the HDD upper bracket

3. Now you can see the bottom bracket

4. Line up the HDD to the four holes of the HDD bracket.

5. Use four screws to fix HDD. 6. Install the upper bracket and then Use screws to fix HDD in the bracket.

7. Unfasten the HDD power cable.

8. Insert the HDD power cable.

9. Use the special data cable to

connect the HDD and the SATA port. Close the chassis and fix the screws to secure firmly.

After completing HDD installation, please check the connection of the data ribbon and power cord, and remount the upper cover with screws fastened.

Note

Power supply must be cut off before HDD installation or replacement

Rack Installation

Please follow the steps listed below.

z Use twelve screws to fix the unit

z Please make sure the indoor temperature is below 35℃ (95°f).

z Please make sure there is 15cm (6 inches) space around the device to

guarantee sound ventilation.

z Please install from the bottom to the top.

z If there are more accessories connected in the rack, please take

precaution measures in case the rack power is overload.

Connecting Power Supply

Please check input voltage and device power button match or not.

We recommend you use UPS to guarantee steady operation, DVR life

span, and other peripheral equipments operation such as cameras.

Connecting Video Input and Output Devices

Connecting Video Input

The video input interface is BNC. The input video format includes: PAL/NTSC BNC（1.0VB

P- P ，

B75Ω.） See X283H283H283HFigure 3-1.X

The video signal should comply with your national standards.

The input video signal shall have high SNR, low distortion; low

interference, natural color and suitable lightness.

Guarantee the stability and reliability of the camera signal:

The camera shall be installed in a cool, dry place away from direct

sunlight, inflammable, explosive substances and etc.

The camera and the DVR should have the same grounding to ensure

the normal operation of the camera.

Guarantee stability and reliability of the transmission lineBTTTB

Please use high quality, sound shielded BNC. Please select suitable

BNC model according to the transmission distance.

If the distance is too long, you should use twisted pair cable, and you

can add video compensation devices or use optical fiber to ensure

video quality.

You should keep the video signal away from the strong electromagnetic

interference, especially the high tension current.

Keep connection lugs in well contact

BTTTB

The signal line and shielded wire should be fixed firmly and in well

connection. Avoid dry joint, lap welding and oxidation.

BTTTB

Figure 3- 1 Connecting Video Input

Connecting Video Output

Video output includes a BNC(PAL/NTSC 1.0VP-P ，75Ω）output ,a VGA output and HDMI output. System supports BNC, VGA and HDMI output at the same time. See Figure 3-2.<0}

When you are using pc-type monitor to replace the monitor, please pay attention to the following points:

z To defer aging, do not allow the pc monitor to run for a long time.

z Regular demagnetization will keep device maintain proper status.

z Keep it away from strong electromagnetic interference devices.

Using TV as video output device is not a reliable substitution method. You also need to reduce the working hour and control the interference from power supply and other devices. The low quality TV may result in device damage.

Figure 3- 2 Connecting Video Output

Connecting Audio Input & Output, Bidirectional Audio

Audio Input

These series products audio input port adopt BNC port.

Due to high impedance of audio input, please use active sound pick-up.

See

X285H285H285HFigure 3-3.

Audio transmission is similar to video transmission. Try to avoid

interference, dry joint, loose contact and it shall be away from high

tension

Figure 3- 3 Audio Input

Audio Output

The audio output signal parameter is usually over 200mv 1KΩ (BNC). It

can directly connect to low impedance earphone, active sound box or

amplifier-drive audio output device.

If the sound box and the pick-up cannot be separated spatially, it is

easy to arouse squeaking. In this case you can adopt the following

measures:

z Use better sound pick-up with better directing property.

z Reduce the volume of the sound box.

z Using more sound-absorbing materials in decoration can reduce voice

echo and improve acoustics environment.

z Adjust the layout to reduce happening of the squeaking.

Please refer to

X286H286H286HFigure 3-4X.

Figure 3- 4 Audio Output

Alarm Input and Output Connection

Please refer to the following sheet for alarm input and output connection.

See

X287H287H287HFigure 3-5.X

Figure 3- 5 Alarm Input and Output Connection

There are two alarm input types for you to select: normal open (NO) and

normal close (NC).

1. Alarm input

a. Please make sure alarm input mode is grounding alarm input.

b. Grounding signal is needed for alarm input.

c. Alarm input needs the low level voltage signal.

d. Alarm input mode can be either NC (normal Open) or NO (Normal Close)

e. When you are connecting two DVRs or you are connecting one DVR

and one other device, please use a relay to separate them,

2. Alarm output

The alarm output port should not be connected to high power load

directly (It shall be less than 1A) to avoid high current which may result

in relay damage. Please use the co contactor to realize the connection

between the alarm output port and the load.

3. How to connect PTZ decoder

a. Ensure the decoder has the same grounding with DVR, otherwise

you may not control the PTZ. Shielded twisted wire is recommended

and the shielded layer is used to connect to the grounding.

b. Avoid high voltage. Ensure proper wiring and some thunder

protection measures.

c. For too long signal wires, 120Ω should be parallel connected between

A, B lines on the far end to reduce reflection and guarantee the signal

quality.

d. “485 A, B” of DVR cannot parallel connect with “485 port” of other

device.

e. The voltage between of A,B lines of the decoder should be less than

5v.

4. Please make sure the front-end device has soundly earthed.

Improper grounding may result in chip damage.

Alarm Input and Output Details

You can refer to the following sheet and X288H288H288HFigure 3-6X for alarm input and

output information.

Important

Please refer to the specifications for the alarm input and output

channel amount. Do not merely count the alarm input and out

channel amount according to the ports on the rear panel.

Figure 3- 6. Alarm Input and Output

You can refer to the following sheet and 671HFigure 3- 6 for alarm input and

output information.

In the first line, from the left to the

right,: 1，2，3， 4，5，6，7，8， 9，10，11，12， 13，14，15，16

ALARM 1 to ALARM 16. The alarm becomes active in low voltage.

In the first line after the number 1-16, from the left to the right:

NO1 C1， NO2 C2， NO3 C3，

NO4 C4, NO5 C5 NC5

The first four are four groups of normal open activation output (on/off button) NO5 C5 NC5 is a group of NO/NC activation output (on/off button)

CTRL 12V Control power output. You need to close the device power to

cancel the alarm.

+12V It is external power input. Need the peripheral equipment to

provide +12V power (below 1A).

AB cable

connection

Earth cable.

485 A/B 485 communication port. They are used to control devices such as

PTZ. Please parallel connect 120TΩ between A/B cables if there are too many PTZ decoders.

Alarm Input Port

Please refer to the following sheet for more information.

z Normal open or Normal close type.

z Please parallel connect COM end and GND end of the alarm

detector (Provide external power to the alarm detector).

z Please parallel connect the Ground of the DVR and the ground of

the alarm detector.

z Please connect the NC port of the alarm sensor to the DVR alarm

input(ALARM)

z Use the same ground with that of DVR if you use external power to

the alarm device.

Figure 3- 7 Alarm Input

Alarm Output Port

z Provide power to peripheral alarm device.

z To avoid overloading, please read the following relay parameters

sheet carefully.

z RS485 A/B cable is for the A/B cable of the PTZ decoder.

Relay Specification

Model:

JRC-27F

Material of the touch

Silver

Rated switch capacity 30VDC 2A, 125VAC 1A

Maximum switch power 125VA 160W

Maximum switch voltage 250VAC, 220VDC

Rating （Resistance Load）

Maximum switch currency 1A Between touches with same

polarity

1000VAC 1minute

Between touches with different polarity

1000VAC 1minute

Insulation

Between touch and winding 1000VAC 1minute

Surge voltage

Between touches with same polarity

1500V (10×160us)

Length of open time

3ms max

Length of close time

3ms max

Mechanical 50×106 times (3Hz)

Longevity

Electrical 200×103 times (0.5Hz)

Temperature

-40℃ ~+70℃

RS232

You can connect the DVR with POS or Keyboard through RS232.

With POS system, the DVR can communicate through RS232 and network. For the POS system, the DVR can integrate the text content and even search the record through the info.

The series DVR also support NKB operation. You can operate the DVR from the keyboard controls instead of using the control pad on the front panel of the unit.

To connect a NKB keyboard to the DVR:

1. Assemble the KBD keyboard according to the instructions in its

accompanying installation manual.

2. Connect the KBD keyboard into one of the RS232 ports on the DVR or

through network.

RS485

When the DVR receives a camera control command, it transmits that

command up the coaxial cable to the PTZ device. RS485 is a single-

direction protocol; the PTZ device can’t return any data to the unit. To

enable the operation, connect the PTZ device to the RS485 (A,B) input

on the DVR. See

672HFigure 3- 6X289H289H289H

Since RS485 is disabled by default for each camera, you must enable

the PTZ settings first. This series DVRs support multiple protocols such

as Pelco-D, Pelco-P.

To connect PTZ devices to the DVR:

1. Connect RS485 A,B on the DVR rear panel.

2. Connect the other end of the cable to the proper pins in the

connector on the camera.

3. Please follow the instructions to configure a camera to enable each

PTZ device on the DVR.

Other Interfaces

There are still other interfaces on the DVR, such as USB ports. You can

refer to the

673HFigure 3- 8 for more information.

Figure 3- 8 Other Interfaces

4 Overview of Navigation and Controls

Note:All the operations listed below are based on the 2U series

product.

Before operation, please make sure:

z You have properly installed HDD and all the cable connections.

z The provided input power and the device power are matched.

z The external power shall be DC 12V.

z Always use the stable current, if necessary UPS is a best alternative

measure.

After system booted up, system pops up the startup wizard.

Click the Cancel button; you can go to the system login interface.

Click the Next Step button; you can go to the startup wizard interface.

Here you can set the system basic information. See 674HFigure 4-1.

Figure 4-1 Startup Wizard

The system login interface is shown as in 675HFigure 4-2.

System consists of four accounts:

z Username: admin. Password: admin. (administrator, local and

network)

z Username: 888888. Password: 888888. (administrator, local only)

z Username: 666666. Passwords: 666666(Lower authority user who

can only monitor, playback, backup and etc.)

z Username: default. Password: default(hidden user)

You can use USB mouse, front panel, remote control or keyboard to

input. About input method: Click

to switch between numeral,

English character (small/capitalized) and denotation.

Note:

For security reason, please modify password after you first login.

Within 30 minutes, three times login failure will result in system alarm

and five times login failure will result in account lock!

Figure 4-2 Menu Login

Main Menu

After you logged in, the system main menu is shown as below. See

676HFigure 4-3.

There are total six icons: search, information, setting, backup,

advanced and shutdown.

You can move the cursor to highlight the icon, and then double click

mouse to enter the sub-menu.

Figure 4-3 Main Menu

Logout

There are two ways for you to log out.

One is from menu option:

In the main menu, click shutdown button, you can see an interface is

shown as below. See 677HFigure 4-4.

Figure 4-4 Logout Menu

There are several options for you. See 678HFigure 4-5.

Figure 4-5 Options for Logout

The other ways is to press power button on the front panel for at

least 3 seconds, system will stop all operations. Then you can click

the power button in the rear panel to turn off the DVR.

Auto Resume after Power Failure

The system can automatically backup video and resume previous

working status after power failure.

Replace Button Battery

Please make sure to use the same battery model if possible.

We recommend replace battery regularly (such as one-year) to

guarantee system time accuracy.

Note:

Before replacement, please save the system setup, otherwise, you

may lose the data completely!

Manual Record

Live Viewing

After you logged in, the system is in live viewing mode. You can see

system date, time and channel name. If you want to change system

date and time, you can refer to general settings (Main Menu-

>Setting->General). If you want to modify the channel name, please

refer to the display settings (Main Menu->Setting->Display)

Preview Zoom Function

Move your mouse to the left top corner of the preview interface; you

can see the preview zoom button. See

679HFigure 4-6. Left click the icon;

you can see a hook icon. Now you have enabled the preview zoom

function. You can drag the mouse to zoom in the image.

Recording status

Video loss

Motion detection

Camera lock

Figure 4-6 Preview Zoom Function

Manual record

Note:

You need to have proper rights to implement the following operations.

Please make sure the HDD has been properly installed.

Manual record menu

There are two ways for you to go to manual record menu.

z Right click mouse or in the main menu, Advanced->Manual Record.

z In live viewing mode, click record button in the front panel or

record button in the remote control.

Manual record menu is shown as in

680HFigure 4-7.

Basic operation

There are three statuses: schedule/manual/stop. Please highlight icon“○” to select corresponding channel.

Preview

zoom button

z Manual: The highest priority. After manual setup, all selected

channels will begin ordinary recording.

z Schedule: Channel records as you have set in recording setup

(Main Menu->Setting->Schedule)

z Stop: All channels stop recording.

Figure 4-7 Recording Control Menu

Enable/disable record

Please check current channel status: “○” means it is not in recording

status, “●” means it is in recording status.

You can use mouse or direction key to highlight channel number.

See

681HFigure 4-8.

Figure 4-8 Different Status of Manual Record

Enable all channel recording

Highlight ○ below All, you can enable all channel recording.

z All channel schedule record

Please highlight “ALL” after “Schedule”. See

682HFigure 4-9.

When system is in schedule recording, all channels will record as

you have previously set (Main menu->Setting->Schedule).

The corresponding indication light in front panel will turn on.

Figure 4-9 Automatic Recording in All Channels

z All channel manual record

Please highlight “ALL” after “Manual.” See

683HFigure 4-10.

When system is in manual recording, all scheduled set up you have

set in will be null ((Main menu->Setting->Schedule)).

You can see indication light in front panel turns on, system begins

manual record now.

Figure 4-10 Start Manual Record in All Channels

Stop all channel recording

Please highlight “ALL” after “Stop”. See 684HFigure 4-11.

System stops all channel recording no matter what mode you have

set in the menu (Main menu->Setting->Schedule)

Figure 4-11 Stop Recording in All Channels

Search & Playback

Click search button in the main menu, search interface is shown as

below. See

685HFigure 4-12.

Usually there are three file types:

z R: Regular recording file.

z A: External alarm recording file.

z M: Motion detection recording file

Figure 4-12 Record Search Menu

Please refer to the following sheet for more information.

Name

Function

Display window

Here is to display the searched picture or file. Support 1/4/9/16-window playback.

Search type

Here you can select to search the picture or the recorded file. When there is displayed picture on the left pane, you can set the corresponding setup

12 9

Calendar

The blue highlighted date means there is picture or file. Otherwise, there is no picture or file. In any play mode, click the date you want to see, you can see the corresponding record file trace in the time bar.

Playback mode and channel selection pane.

Playback mode：1/4/9/16. (It may vary due to different series.) In 1-window playback mode: you can select 1-16 channels. In 4-window playback mode: you can select 4 channels according to your requirement. In 9-window playback mode, you can switch between 1-9 and 1016 channels. In 16-window playback mode, you can switch between1-16 and 17-32 channels. The time bar will change once you modify the playback mode or the channel option.

File list switch button

Double click it, you can view the picture/record file list of current day. The file list is to display the first channel of the record file. The system can display max 128 files in one time. Use the S/T or the mouse to view the file. Select one item, and then double click the mouse or click the ENTER button to playback. You can input the period in the following interface to begin accurate search.

File type：R—regular record； A—external alarm record；M— Motion detect record.

Card number search

The card number search interface is shown as below.

►/ 

Play/Pause There are three ways for you to begin playback. The play button Double click the valid period of the time bar. Double click the item in the file list. In slow play mode, click it to switch between play/pause.

Playback control pane.

■ Stop

Backward play In normal play mode, left click the button, the file begins backward play. Click it again to pause current play. In backward play mode, click ►/ to restore normal play.

│W/ X│

In playback mode, click it to play the next or the previous section. You can click continuously when you are watching the files from the same channel. In normal play mode, when you pause current play, you can click W│ and │X to begin frame by frame playback. In frame by frame playback mode, click ►/ to restore normal playback.

► Slow play

In playback mode, click it to realize various slow play modes such as slow play 1, slow play 2, and etc.



Fast forward In playback mode, click to realize various fast play modes

such as fast play 1,fast play 2 and etc. Note: The actual play speed has relationship with the software version.

Smart search

The volume of the playback

Click the snapshot button in the full-screen mode, the

system can snapshot 1 picture per second.

Time bar

It is to display the record type and its period in current search criteria. In 4-window playback mode, there are corresponding four time bars. In other playback mode, there is only one time bar. Use the mouse to click one point of the color zone in the time bar, system begins playback. The time bar is beginning with 0 o'clock when you are setting the configuration. The time bar zooms in the period of the current playback time when you are playing the file. The green color stands for the regular record file. The red color stands for the external alarm record file. The yellow stands for the motion detect record file.

Time bar unit

The option includes: 24H, 12H, 1H and 30M. The smaller the unit, the larger the zoom rate. You can accurately set the time in the time bar to playback the record. The time bar is beginning with 0 o'clock when you are setting the configuration. The time bar zooms in the period of the current playback time when you are playing the file.

Backup

Select the file(s) you want to backup from the file list. System max supports files from four channels. Then click the backup button, now you can see the backup menu. Click the start button to begin the backup operation. Check the file again you can cancel current selection. System max supports to display 32 files from one channel.

Clip

It is to edit the file. Please play the file you want to edit and then click this button when you want to edit. You can see the corresponding slide bar in the time bar of the corresponding channel. You can adjust the slide bar or input the accurate time to set the file end time. Click this button again and then save current contents in a new file. .

Record type

In any play mode, the time bar will change once you modify the search type.

Smart search

When system is playing, you can select a zone in the window to begin motion detect. Click the motion detect button to begin play. Current button is null once the motion detect play has begun. The system will take the whole play zone as the motion detect region by default. The motion detect play stopped once you switch the play file. Operations such as set time bar, click the play button, or any file list operation will stop current motion detect play.

Other Functions

Other channel synchronization switch to play when playback

When playing the file, click the number button, system can switch to the same period of the corresponding channel to play.

15 Digital zoom

When the system is in full-screen playback mode, left click the mouse in the screen. Drag your mouse in the screen to select a section and then left click mouse to realize digital zoom. You can right click mouse to exit.

Note:

All the operations here (such as playback speed, channel, time and

progress) have relationship with hardware version. Some series

DVRs do not support some functions or playback speeds.

Schedule

After system booted up, it is in default 24-hour regular mode. You

can set record type and time in schedule interface.

Schedule Menu

In the main menu, from setting to schedule, you can go to schedule

menu. See

686HFigure 4-13.

z Channel: Please select the channel number first. You can select

“all” if you want to set for the whole channels.

z Week day: There are eight options: ranges from Saturday to

Sunday and all.

z Pre-record: System can pre-record the video before the event

occurs into the file. The value ranges from 1 to 30 seconds

depending on the bit stream.

z Redundancy: System supports redundancy backup function. It

allows you backup recorded file in two disks. You can highlight

Redundancy button to activate this function. Please note, before

enable this function, please set at least one HDD as redundant.

(Main menu->Advanced->HDD Management) Please refer to

chapter 4.4.1.2 for detailed information.

z Snapshot: You can enable this function to snapshoot image when

alarm occurs.

z Record types: There are four types: regular, motion detection (MD),

Alarm, MD & alarm.

Please highlight icon

to select the corresponding function. After

completing all the setups please click save button, system goes back

to the previous menu.

At the bottom of the menu, there are color bars for your reference.

Green color stands for regular recording, yellow color stands for

motion detection and red color stands for alarm recording. The white

means the MD and alarm record is valid. Once you have set to

record when the MD and alarm occurs, system will not record neither

motion detect occurs nor the alarm occurs.

Figure 4-13 Schedule Setting

Quick Setup

This function allows you to copy one channel setup to another. After

setting in channel 1, you can click paste button and turn to channel 2

and then click copy button. You can finish setting for one channel

and then click save button or you can finish all setup and then click

save button to memorize all the settings.

Redundancy

Redundancy function allows you to memorize record file in several

disks. When there is file damage occurred in one disk, there is a

spare one in the other disk. You can use this function to maintain

data reliability and safety.

In the main menu, from Setting to Schedule, you can highlight

redundancy button to enable this function. See

687HFigure 4-13.

In the main menu, from Advanced to HDD management, you can set

one or more disk(s) as redundant. You can select from the dropdown

list. See

688HFigure 4-14. System auto overwrites old files once hard disk

is full.

Please note only read/write disk or read-only disk can backup file

and support file search function, so you need to set at least one

read-write disk otherwise you can not record video.

Note

About redundancy setup:

z If current channel is not recording, current setup gets activated

when the channel begin recording the next time.

z If current channel is recording now, current setup will get activated

right away, the current file will be packet and form a file, then system begins recording as you have just set.

z After all the setups please click save button, system goes back to

the previous menu.

Figure 4-14 redundancy setup

Playback or search in the redundant disk.

There are two ways for you to playback or search in the redundant

disk.

z Set redundant disk(s) as read-only disk or read-write disk (Main

menu->Advanced->HDD management). See

689HFigure 4-14.System

needs to reboot to get setup activated. Now you can search or playback file in redundant disk.

z Dismantle the disk and play it in another PC.

Snapshot

Schedule Snapshot

In Encode interface, click snapshot button to input snapshot mode,

size, quality and frequency.

In General interface please input upload interval.

In Schedule interface, please enable snapshot function.

Please refer to the following figure for detailed information. See

690HFigure 4-15

Figure 4-15 Schedule Snapshot Setting

Activation Snapshot

Please follow the steps listed below to enable the activation

snapshot function. After you enabled this function, system can

snapshot when the corresponding alarm occurred.

z In Encode interface, click snapshot button to input snapshot mode,

size, quality and frequency.

z In General interface please input upload interval.

z In Detect interface please enable snapshot function for specified

channels. Or in alarm interface please enable snapshot function for specified channels.

Please refer to the following figure for detailed information. See

691HFigure 4-16.

Figure 4-16 Activation Snapshot Setting

Priority

Please note the activation snapshot has the higher priority than

schedule snapshot. If you have enabled these two types at the same

time, system can activate the activation snapshot when alarm occurs,

and otherwise system just operates the schedule snapshot.

Image FTP

In Network interface, you can set FTP server information. Please

enable FTP function and then click save button. See

692HFigure 4-17.

Please boot up corresponding FTP server.

Please enable schedule snapshot (Chapter 4.4.2.1) or activation

snapshot (Chapter 4.4.2.2) first, now system can upload the image

file to the FTP server.

Figure 4-17 Image FTP Stting

Snapshot Disk (For special series only)

Set one disk as snapshot (Main menu->Advanced->HDD

management) and then click execute button. See

693HFigure 4-18. System

needs to reboot to get current setup activated.

Figure 4-18 Snapshot Disk Setting

Please input the

corresponding

information here, if you

just upload the image

FTP.

All scheduled snapshot files or activated snapshot files will be

memorized in the snapshot disk.

You can search the corresponding images via Web. See

694HFigure 4-19.

Figure 4-19 Search Image Via Web

Select search

engine here

You can see result here. Double click

file name, you can view the image

content.

There are max 100 files in one

page. Click here to view more.

Select a file and then

click here to view

image content.

Detect

Go to Detect Menu

In the main menu, from Setting to Detect, you can see motion detect

interface. See

695HFigure 4-20.There is three detection types: motion

detection, video loss, camera masking.

Motion Detect

Detection menu is shown as below. See 696HFigure 4-20

z Event type: from the dropdown list you can select motion detection

type.

z Channel: select the channel to activate recording function once

alarm occurred. Please make sure you have set MD record in encode interface(Main Menu->Setting->Schedule) and schedule record in manual record interface(Main Menu->Advanced->Manual Record)

z Latch: when motion detection complete, system auto delays

detecting for a specified time. The value ranges from 10-300(Unit: second)

z Region: Click select button, the interface is shown as in

697HFigure 4-21.

Here you can set motion detection zone. There are 396(PAL)/330(NTSC) small zones. The green zone is current cursor position. Grey zone is the motion detection zone. Black zone is the disarmed zone. You can click Fn button to switch between the arm mode and disarm mode. In arm mode, you can click the direction buttons to move the green rectangle to set the motion detection zone. After you completed the setup, please click ENTER button to exit current setup. Do remember click save button to save current setup. If you click ESC button to exit the region setup interface system will not save your zone setup.

z Sensitivity: System supports 6 levels. The sixth level has the

highest sensitivity.

z Show message: System can pop up a message to alarm you in the

local host screen if you enabled this function.

z Alarm upload: System can upload the alarm signal to the network

(including alarm centre) if you enabled current function.

z Send email: System can send out email to alert you when alarm

occurs.

z PTZ activation: Here you can set PTZ movement when alarm

occurs. Such as go to preset, tour &pattern when there is an alarm. Click “select” button, you can see an interface is shown as in

698HFigure

4-22

z Period: Click set button, you can see an interface is shown as in

699HFigure 4-23. Here you can set for business day and non-business

day. In

700HFigure 4-23 click set button, you can see an interface is

shown as in

701HFigure 4-24. Here you can set your own setup for

business day and non-business day.

z Anti-dither: Here you can set anti-dither time.

z Alarm output: when alarm occurred, system enables peripheral

alarm devices.

z Tour: Here you can enable tour function when alarm occurs.

System one-window tour. Please go to chapter 5.3.9 Display for tour interval setup.

z Snapshot: You can enable this function to snapshoot image when

alarm occurs.

Please highlight icon

to select the corresponding function. After

all the setups please click save button, system goes back to the

previous menu.

Note:

In motion detection mode, you can not use copy/paste to set channel

setup since the video in each channel may not be the same.

702HFigure 4-21, you can left click mouse and then drag it to set a

region for motion detection. Click Fn to switch between arm/withdraw

motion detection. After setting, click enter button to exit.

Figure 4-20 Motion Detect Setting

Figure 4-21 Motion Detection Zone Setting

Figure 4-22 PTZ Activation Setting

Figure 4-23 Armed Period Setting

Figure 4-24 Business Day and Non-Business Day Setting

Video Loss

In 703HFigure 4-20, select video loss from the type list. You can see the

interface is shown as in

704HFigure 4-25.This function allows you to be

informed when video loss phenomenon occurred. You can enable

alarm output channel and then enable show message function.

Tips:

You can enable preset activation operation when video loss occurs.

Please refer to chapter 4.5.2 motion detection for detailed

information.

Figure 4-25 Video Loss Setting

Camera Masking

When someone viciously masks the lens, or the output video is in

one-color due to the environments light change, the system can alert

you to guarantee video continuity. Camera masking interface is

shown as in

705HFigure 4-26.

Tips:

You can enable preset/tour/pattern activation operation when video

loss occurs.

Please refer to chapter 4.5.2 motion detection for detailed

information.

Note:

In Detect interface, copy/paste function is only valid for the same

type, which means you can not copy a channel setup in video loss

mode to camera masking mode.

Figure 4-26 Camera Masking Setting

Alarm Setup and Alarm Activation

Before operation, please make sure you have properly connected

alarm devices such as buzzer.

Go to alarm setup interface

In the main menu, from Setting to Alarm, you can see alarm setup

interface. See

706HFigure 4-27.

Alarm setup

Alarm interface is shown as below. See 707HFigure 4-27.

z Alarm in: Here is for you to select channel number.

z Event type: There are two types. One is local input and the other is

network input.

z Type: normal open or normal close.

z PTZ activation: Here you can set PTZ movement when alarm

occurs. Such as go to preset, tour& pattern when there is an alarm. Click “select” button, you can see an interface is shown as in

708HFigure

4-28

z Period: Click set button, you can see an interface is shown as in

709HFigure 4-29. Here you can set for business day and non-business

day. In

710HFigure 4-29, click set button, you can see an interface is

shown as in

711HFigure 4-30. Here you can set your own setup for

business day and non-business day.

z Anti-dither: Here you can set anti-dither time.

z Show message: System can pop up a message to alarm you in the

local host screen if you enabled this function.

z Alarm upload: System can upload the alarm signal to the network

(including alarm centre) if you enabled current function.

z Send email: System can send out email to alert you when alarm

occurs.

z Record channel: you can select proper channel to record alarm

video (Multiple choices). At the same time you need to set alarm record in schedule interface (Main Menu->Setting->Schedule) and select schedule record in manual record interface (Main Menu>Advance->Manual Record).

z Latch: Here is for you to set proper delay duration. Value ranges

from 10 to 300 seconds. System automatically delays specified seconds in turning off alarm and activated output after external alarm cancelled.

z Tour: Here you can enable tour function when alarm occurs.

System supports one-window tour. Please go to chapter 5.3.9 Display for tour interval setup.

z Buzzer: Highlight the icon to enable this function. The buzzer beeps

when alarm occurs.

For snapshot operation, please refer to chapter 4.4.2.

Please highlight icon

to select the corresponding function. After

setting all the setups please click save button, system goes back to

the previous menu.

Figure 4-27 Local Alarm Setting

Figure 4-28 PTZ Activation Settings

Figure 4-29 Period Setting

Figure 4-30 Business Days and Non-Business Days Settings

Backup

DVR support USB device backup and network download. Here we

introduce USB backup. You can refer to Chapter 7 Web Client

Operation for network download backup operation.

Detect Device

Click backup button, you can see an interface is shown as in 712HFigure

4-31

. Here is for you to view devices information.

You can view backup device name and its total space and free space.

The device includes USB burner, flash disk, SD card, and portable

HDD.

Figure 4-31 Device Detection Menu of Backup

Backup

Select backup device and then set channel, file start time and end

time.

Click add button, system begins search. All matched files are listed

below. System automatically calculates the capacity needed and

remained. See

713HFigure 4-32.

system only backup files with a √ before channel name. You can use Fn or cancel button to delete √ after file serial number.

Click backup button, you can backup selected files. There is a

process bar for you reference.

When the system completes backup, you can see a dialogue box

prompting successful backup.

Figure 4-32 Backup Menu with Search Results

Click backup button, system begins burning. At the same time, the

backup button becomes stop button. You can view the remaining

time and process bar at the left bottom.

z File format: Click the file format; you can see there are two options:

DAV/ASF.

z Picture backup: Please set the corresponding time, channel and

then select the type as PIC from the dropdown list. See

714HFigure 4-33.

Please click the Add button and then select the pictures. Click the Start button; you can copy the specified pictures to the selected portable devices.

Figure 4-33 Select The Type

z One key backup: It includes three steps: the search, select all, start

the backup. You can skip the above three steps and then copy all the searched files directly.

The file name format usually is: SN_CH+channel number+time

Y+M+D+H+M+S. In the file name, the YDM format is the same as

you set in general interface. (Main Menu ->Setting ->General).File

extension name is .dav.

Tips:

During backup process, you can click ESC to exit current interface

for other operation. The system will not terminate backup process.

Note:

When you click stop button during the burning process, the stop

function becomes activated immediately. For example, if there are

ten files, when you click stop system just backup five files, system

only save the previous 5 files in the device (But you can view ten file

names).

PTZ Control and Color Setup

Note: All the operations here are based on PELCOD protocol. For

other protocols, there might be a little difference.

Cable Connection

Please follow the procedures below to go on cable connection

z Connect the dome RS485 port to DVR 485 port.

z Connect dome video output cable to DVR video input port.

z Connect power adapter to the dome.

PTZ Setup

Note: The camera video should be in the current screen. Before

setup, please check the following connections are right:

z PTZ and decoder connection is right. Decoder address setup is

right.

z Decoder A (B) line connects with DVR A (B) line.

Boot up the DVR, input user name and password.

In the main menu, click setting, and then click Pan/Tilt Control button.

The interface is shown as in

715HFigure 4-34. Here you can set the

following items:

z Channel: select the current camera channel.

z Protocol: select corresponding PTZ protocol(such as PELCOD)

z Address: default address is 1.

z Baud rate: select corresponding baud rate. Default value is 9600.

z Data bits: select corresponding data bits. Default value is 8.

z Stop bits: select corresponding stop bits. Default value is 1.

z Parity: there are three options: odd/even/none. Default setup is

none.

Figure 4-34 PTZ Setting

After completing all the setting please click save button.

In one window display mode, right click mouse (click “Fn” Button in

the front panel or click “Fn” key in the remote control). The interface

is shown as in

716HFigure 4-35.

Figure 4-35 Context Menu

Click Pan/Tilt/Zoom, the interface is shown as below. See 717HFigure 4-36.

Here you can set the following items:

z Step: value ranges fro 1 to 8.

z Zoom

z Focus

z Iris

Please click icon and to adjust zoom, focus and iris.

Figure 4-36 PTZ Control Menu

In 718HFigure 4-36, please click direction arrows (See 719HFigure 4-37) to adjust

PTZ position. There are total 8 direction arrows.

Figure 4-37 Direction Arrows

Here is a sheet for you reference.

Name

Function key

function

Shortcut key

Function key

function

Shortcut Key

Zoom

Near

Far



Focus

Near │W

Far ►│

Iris

Close W

Open ►

Preset/ Patrol/Pattern/Scan

In 720HFigure 4-36, please click the “set” button. The interface is shown as

below. See

721HFigure 4-39.

Here you can set the following items:

z Preset

z Tour

z Pattern

z Border

Figure 4-38 PTZ Setup Menu

In X328H328H328H 722HFigure 4-36, click page switch button, the interface is shown as in

723HFigure 4-38 .

Here you can activate the following functions:

z Preset

z Tour

z Pattern

z Auto scan

z Auto pan

z Flip

z Reset

z Page switch

Figure 4-39 PTZ Function Menu

Note:

z Preset, tour and pattern all need the value to be the control parameter.

You can define it as you require.

z You need to refer to your speed dome user’s manual for Aux definition.

In some cases, it can be used for special process.

z The following setups are usually operated in the

X332H332H332H724HFigure 4-36, 725HFigure

4-38

and 726HFigure 4-39.

Preset Setup

In 727HFigure 4-36, use eight direction arrows to adjust camera to the proper

position.

728HFigure 4-38, click preset button and input preset number. The interface

is shown as in

729HFigure 4-40.

Now you can add this preset to one tour.

Figure 4-40 Preset Setting

Activate Preset

In 730HFigure 4-39, please input preset number in the No. blank, and click

preset button.

Patrol setup (Tour Setup)

In Figure 4-38, click patrol button. The interface is shown as in 731HFigure

4-41

.Input preset number and add this preset to a patrol (tour). For each

patrol (tour), you can input max 80 presets.

Figure 4-41 Tour Setting

Activate Patrol (tour)

In X341H341H341H 732HFigure 4-39, input patrol (tour) number in the No. blank and click

patrol button

Pattern Setup

In 733HFigure 4-38, click pattern button and then click “begin” button. The

interface is shown as in

734HFigure 4-42. Then you can go to 735HFigure 4-36 X to

modify zoom, focus, and iris.

Go back to

736HFigure 4-42 and click “end” button. You can memorize all

these operations as pattern 1.

Figure 4-42 Pattern Setting

Activate Pattern Function

In X346H346H346H Figure 4-39, input mode value in the No. blank, and click pattern

button.

Auto Scan Setup

In X347H347H347H Figure 4-38, click border button. The interface is shown as in X348H348H348H Figure

4-43.

Please go to

X349H349H349H 737HFigure 4-369H349H, use direction arrows to select camera left limit

Then please go to

X350H350H350H Figure 4-43X and click left limit button

Repeat the above procedures to set right limit.

Figure 4-43 Auto Scan Setting

Activate Auto Scan

In 738HFigure 4-39, click “Auto Scan” button, the system begins auto scan.

Correspondingly, the auto scan button becomes Stop button. Click stop

button to terminate scan operation.

Flip

In 739HFigure 4-39, click page switch button, you can see an interface is

shown as below. See

740HFigure 4-44. Here you can set auxiliary function.

The aux value has relation ship with the Aux button of the decoder.

Click page switch button again, system goes back to

741HFigure 4-36.

Figure 4-44 Auxiliary Setting

5 Understanding of Menu Operations and

Controls

Menu Tree

This series DVR menu tree is shown as below.

Backup

Information

HDD Info BPS Log Version Online Users

Setting General Encode

Schedule RS232

Menu Network

Alarm Detect Pan/ Tilt/Zoom Display

Default Search Advanced HDD Management

Alarm Output

Abnormity Manual Record Account Auto Maintain TV Adjust Video Matrix Title Overlay Config Backup

Shutdown

Main Menu

After you logged in, the system main menu is shown as below. See

742HFigure 5-1.X There are total six icons: search, Information, setting, backup,

advanced and shutdown. Move the cursor to highlight the icon, then

double click mouse to enter the sub-menu.

Figure 5-1 Main Menu

Setting

In main menu, highlight setting icon and double click mouse. System

setting interface is shown as below. See

743HFigure 5-2.

Figure 5-2 Setting

General

General setting includes the following items. See X357H357H357HFigure 5-3X.

z System time: Here is for you to set system time

z Date format: There are three types: YYYYY-MM-DD: MM-DD-YYYYY or

DD-MM-YYYY.

z Date separator: There are three denotations to separate date: dot,

beeline and solidus.

z DST: Here you can set DST time and date. Please enable DST function

and then click set button. You can see an interface is shown as in

744HFigure

5-4

. Here you can set start time and end time by setting corresponding

week setup. In

745HFigure 5-4, enable date button, you can see an interface

is shown as in Figure 5-5. Here you can set start time and end time by

setting corresponding date setup.

z Time format: There are two types: 24-hour mode or 12-hour mode.

z Language: System supports various languages: Chinese (simplified),

Chinese (Traditional), English, Italian, Japanese, French, Spanish (All

languages listed here are optional. Slight difference maybe found in

various series.)

z HDD full: Here is for you to select working mode when hard disk is full.

There are two options: stop recording or rewrite. If current working HDD

is overwritten or the current HDD is full while the next HDD is no empty,

then system stops recording, If the current HDD is full and then next

HDD is not empty, then system overwrites the previous files.

z Pack duration: Here is for you to specify record duration. The value

ranges from 60 to 120 minutes. Default value is 60 minutes.

z DVR No: When you are using one remote control (not included in the

accessory bag) to control several DVRs, you can give a name to each

DVR for your management.

z Video standard: There are two formats: NTSC and PAL.

z Auto logout: Here is for you to set auto logout interval once login user

remains inactive for a specified time. Value ranges from 0 to 60 minutes.

z Startup wizard: Once you check the box here, system will go to the

startup wizard directly when the system restarts the next time.

Otherwise, it will go to the login interface.

z Device ID: Please input a corresponding device name here.

Note:

Since system time is very important, do not modify time casually unless

there is a must!

Before your time modification, please stop record operation first!

After completing all the setups please click save button, system goes

back to the previous menu.

Figure 5-3 General Setting

Figure 5-4 DST Setup Menu (Week)

Figure 5-5 DST setup menu (Date)

Encode

Encode setting includes the following items. See 746HFigure 5-6.

Please note some series do not support extra stream.

z Channel: Select the channel you want.

z Type: Please select from the dropdown list. There are three options:

regular/motion detect/alarm. You can set the various encode

parameters for different record types.

z Compression: System supports H.264.

z Resolution: System supports various resolutions, you can select from

the dropdown list. The main stream supports D1/HD1/BCIF/CIF/QCIF

and the extra stream supports CIF/QCIF. Please note the option may

vary due to different series.

z Frame rate: It ranges from 1f/s to 25f/s in NTSC mode and 1f/s to 30f/s

in PAL mode.

z Bit rate type: System supports two types: CBR and VBR. In VBR mode,

you can set video quality.

z Quality: There are six levels ranging from 1 to 6. The sixth level has the

highest image quality.

z Video/audio: You can enable or disable the video/audio.

z Overlay: Click overlay button, you can see an interface is shown in

747HFigure 5-7.

 Cover area (Privacy mask): Here is for you to set privacy mask

section. You can drag you mouse to set proper section size. In one

channel video, system max supports 4 zones in one channel.

 Preview/monitor: privacy mask has two types. Preview and Monitor.

Preview means the privacy mask zone can not be viewed by user

when system is in preview status. Monitor means the privacy mask

zone can not be view by the user when system is in monitor status.

 Time display: You can select system displays time or not when you

playback. Please click set button and then drag the title to the

corresponding position in the screen.

 Channel display: You can select system displays channel number

or not when you playback. Please click set button and then drag

the title to the corresponding position in the screen.

Please highlight icon

to select the corresponding function.

Figure 5-6 Encode Menu

Figure 5-7 Encode Menu

Schedule

Please refer to chapter 4.4 schedule.

RS232

RS232 interface is shown as below. There are five items. See 748HFigure 5-8.

z Function: There are various devices for you to select. Console is for you

to use the COM or mini-end software to upgrade or debug the program.

The control keyboard is for you to control the device via the special

keyboard. Transparent COM (adapter) is to connect to the PC to

transfer data directly. Protocol COM is for card overlay function.

Network keyboard is for you to use the special keyboard to control the

device. PTZ matrix is to connect to the peripheral matrix control.

z Baud rate: You can select proper baud rate.

z Data bit: You can select proper data bit. The value ranges from 5 to 8.

z Stop bit: There are three values: 1/1.5/2.

z Parity: there are five choices: none/odd/even/space mark.

z System default setup is:

z Function: Console

z Baud rate:115200

z Data bit:8

z Stop bit:1

z Parity: None

After completing all the setups please click save button, system goes

back to the previous menu.

Figure 5-8 RS232 Setup Menu

Network

Here is for you to input network information. See 749HFigure 5-9.

z IP address: Here you can input IP address.

z DHCP: It is to auto search IP. When enable DHCP function, you can not

modify IP/Subnet mask /Gateway. These values are from DHCP

function. If you have not enabled DHCP function, IP/Subnet

mask/Gateway display as zero. You need to disable DHCP function to

view current IP information. Besides, when PPPoE is operating, you

can not modify IP/Subnet mask /Gateway.

z TCP port: Default value is 37777.

z UDP port: Default value is 37778.

z HTTP port: Default value is 80.

z RTSP port: Default value is 554.

z Max connection: system support maximal 20 users. 0 means there is no

connection limit.

z Preferred DNS server: DNS server IP address.

z Alternate DNS server: DNS server alternate address.

z Transfer mode: Here you can select the priority between fluency/video

qualities.

z LAN download: System can process the downloaded data first if you

enable this function. The download speed is 1.5X or 2.0X of the normal

speed.

After completing all the setups please click save button, system goes

back to the previous menu.

Figure 5-9 Network Setup Menu

Advanced Setup

Advanced setup interface is shown as in 750HFigure 5-10. Please draw a circle to enable corresponding function and then double click current item to go to setup interface.

Figure 5-10 Advanced Settings

IP Filter

IP filter interface is shown as in 751HFigure 5-11. You can add IP in the

following list. The list supports max 64 IP addresses.

Please note after you enabled this function, only the IP listed below can

access current DVR.

If you disable this function, all IP addresses can access current DVR.

Figure 5-11 IP Filter Menu

NTP Setup

Honeywell CADVR-04D, CADVR-08D, CADVR-16D User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual