Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other
information contained in this document without prior notice, and the reader should in all cases consult HII
to determine whether any such changes have been made. The information in this publication does not
represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or
consequential damages resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights are reserved. No
part of this document may be photocopied, reproduced, or translated into another language without the
prior written consent of HII.
Web Address: www.honeywellaidc.com
Trademarks
Dolphin, Dolphin RF, HomeBase, Mobile Base, and QuadCharger are trademarks or registered
trademarks of Hand Held Products, Inc. or Honeywell International Inc.
Microsoft, Windows, Windows Mobile, Windows Embedded Handheld, Windows CE, Windows 98
Second Edition, Windows NT, Windows 2000, Windows ME, Windows XP, ActiveSync, Outlook, and the
Windows logo are trademarks or registered trademarks of Microsoft Corporation.
Other product names mentioned in this manual may be trademarks or registered trademarks of their
respective companies and are the property of their respective owners.
Patents
For patent information, please refer to www.honeywellaidc.com/patents.
Other Trademarks
The Bluetooth trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to Honeywell.
How to Extend Your Warranty.....................................................................................19-4
ix
x
Preliminary Draft 1/19/11
1
Compliance
Label
Dolphin 99EX with WWAN
Compliance
Label
Dolphin 99EX with WLAN
Image Engines with Integrated Laser Aimers
Preliminary Draft 1/19/11
Agency Information
Dolphin 99EX mobile computers meet or exceed the requirements of all applicable standards
organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe
operation is to operate them according to the agency guidelines that follow. Read these guidelines
carefully before using your mobile computer.
Laser Safety
Label Locations
Laser Safety Label
If the following label is attached to your product, it indicates the product contains an engine with a laser
aimer:
Laser Eye Safety Statement
This device has been tested in accordance with and complies with IEC60825-1(Ed. 2.0), EN608251:2007. Complies with 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No.
50, dated June 24, 2007. LASER LIGHT, DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT,
1.0 mW MAX OUTPUT: 650nm, pulse duration of 15.5msec, and pulse repetition rate of 32.25 Hz.
Caution! Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
1 - 1
LED Safety
Preliminary Draft 1/19/11
LED Safety Statement
LEDs have been tested and classified as “EXEMPT RISK GROUP” to the Standard: IEC 62471:2006.
Infrared LED Safety Statement
Caution! Do not view directly with optical instruments.
UL and C-UL Statement
UL and C-UL listed: UL60950-1 2nd Edition, and CSA C22.2 No. 60950-1-07 2nd Edition, ISA
12.12.01:2007, CAN/CSA: C22.2 No. 213-M1987.
Approvals by Country
CountryEMC, Radio, & SARSafety
U.S.A.FCC Part 15, Subpart B
FCC Part 15, Subpart C, 15.247
FCC Part 15, Subpart E
FCC Part 22H
FCC Part 24E
FCC SAR OET 65 Supplement C
CanadaICES-003 (Class B)
RSS 132
RSS 133
RSS 210
European Community/CEEN300328, EN301893, EN55022, EN55024,
Dolphin RF terminals are in conformity with all essential requirements of the R&TTE Directive (1999/5/
EC).
This product is marked with in accordance with the Class II product requirements specified in
the R&TTE Directive. In addition, this product complies to 2006/95/EC Low Voltage Directive when
supplied with the recommended power supply. Honeywell shall not be liable for use of our product with
equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply
with the Low Voltage Directive.
1 - 2
The equipment is intended for use throughout the European Community; PAN European Frequency
Preliminary Draft 1/19/11
Range: 2.402–2.480 GHz. Restrictions for use in France are as follows:
• Indoor use: Maximum power (EIRP*) of 100 mW for the entire 2.400–2.4835 GHz
• Outdoor use: Maximum power (EIRP*) of 100 mW for the 2.400–2.454 GHz band & maximum power
(EIRP*) of 10 mW for the 2.454–2.483 MGHz band.
• 5Ghz band: UNII (Unlicensed National Information Infrastructure) or band1 (5.150 to 5.250 GHz) is
restricted to indoor use only. Any other use will make the operation of the device illegal.
For further information, please contact:
Honeywell Scanning & Mobility Europe BV
Nijverheidsweg 9
5627 BT Eindhoven
The Netherlands
This device complies with P art 15 of the FCC Rules. Operation is subject to the f ollowing tw o conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications . Howe v er , there is no guarantee that interf erence will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
In accordance with FCC 15.21, changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions. The user may find the following booklet helpful: “Something About Interference.”
This is availab le at FCC local regional offices . Our company is not responsible for any radio or television
interference caused by unauthorized modifications of this equipment or the substitution or attachment of
connecting cables and equipment other than those specified by our company. The correction is the
responsibility of the user. Use only shielded data cables with this system.
1 - 3
Canadian Compliance
Preliminary Draft 1/19/11
0.377
HD599EXL00
N/A
This Class B digital apparatus complies with Canadian ICES-003 and RSS210. Operation is subject to
the following two conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference received, including interference that may cause undesired
operation.
Conformité à la règlementation canadienne
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 et RSS210 du Canada. Son
fonctionnement est assujetti aux conditions suivantes:
1.Cet appareil ne doit pas causer de brouillage préjudiciable.
2.Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le brouillage pouvant causer un
fonctionnement indésirable.
RF Exposure Information (SAR)
This mobile phone meets the government's requirements for exposure to radio waves. This phone is
designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF)
energy set by the Federal Communications Commission of the U.S. Government.
The exposure standard for wireless mobile phones employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are
conducted using standard operating positions accepted by the FCC with the phone transmitting at its
highest certified power level in all tested frequency bands. Although the SAR is determined at the
highest certified power level, the actual SAR level of the phone while operating can be well below the
maximum value. This is because the phone is designed to operate at multiple power levels so as to use
only the poser required to reach the network. In general, the closer you are to a wireless base station
antenna, the lower the power output.
The highest SAR value for the model phone as reported to the FCC when tested for use at the ear is
____W/kg and when worn on the body, as described in this user guide, is _____ W/kg (Body-worn
measurements differ among phone models, depending upon available accessories and FCC
requirements.)
While there may be differences betw een the SAR le vels of various phones and at various positions, they
all meet the government requirement.
The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels
evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone
is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid
after searching on FCC ID: ________________.
For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines for
use with an accessory that contains no metal and the positions the handset a minimum of 1.5 cm from
the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines . If y ou
do no t use a body-worn accessory and are not holding the phone at the ear, position the handset a
minimum of 1.5 cm from your body when the phone is switched on.
1 - 4
For European Community Users
Preliminary Draft 1/19/11
Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Waste Electrical and Electronic Equipment Information
This product has required the extraction and use of natural resources for its production. It may contain
hazardous substances that could impact health and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our en vironment and to diminish the pressure
on the natural resources, we encourage you to use the appropriate take-back systems for product
disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a
sound way.
The crossed out wheeled bin symbol informs you that the product should not be disposed of along
with municipal waste and invites y ou to use the appropriate separate tak e-bac k systems for product
disposal.
If you need more information on the collection, reuse, and recycling systems, please contact your local
or regional waste administration.
You may also contact your supplier for more information on the environmental performances of this
product.
Pacemakers, Hearing Aids and Other Electrically Powered Devices
Most manufacturers of medical devices adhere to the IEC 601-1-2 standard. This standard requires
devices to operate properly in an EM Field with a strength of 3V/m over a frequency range of 26 to
1000MHz. The maximum allowab le field strength emitted b y the Dolphin terminal is 0.3V/m according to
Subpart B of Part 1 of the FCC rules. Therefore, the RF from the Dolphin terminal has no effect on
medical devices that meet the IEC specification.
Microwaves
The radio in the Dolphin RF terminal operates on the same frequency band as a microwave oven.
Therefore, if you use a microwave within range of the Dolphin RF terminal you may notice performance
degradation in your wireless network. However, both your microwave and your wireless network will
continue to function.
1 - 5
1 - 6
Preliminary Draft 1/19/11
2
2.
3.
!
Preliminary Draft 1/19/11
Getting Started
Out of the Box
Verify that the carton contains the following items:
• Dolphin 99EX mobile computer (the terminal)
• Main battery pack (i.e., standard 3.7V Li-poly or extended 3.7V Li-ion)
• Quick Start Guide
Note: If you ordered accessories for your terminals, verify that they are also included with the order.
Be sure to keep the original packaging in the event that the Dolphin terminal should need to be returned
for service. For details, see Product Service and Repair on page 19-1.
Step 1. Install the Main Battery Pack
The 99EX is shipped with the battery packaged separate from the unit. Follow the steps below to install
the main battery.
1.Release the hook securing the hand strap to the
back panel of the terminal near the speaker.
2.Remove the battery door by lifting up the latches
near the base of the battery door.
3.Insert the battery into the battery well.
4.Replace the battery door. Apply pressure to
engage the door latch.
Note: The battery door must be installed prior to
powering the unit.
5.Reattach the hand strap.
We recommend use of Honeywell Li-poly or Li-Ion
battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.
Step 2. Charge the Main and Backup Batteries
The power supply for Dolphin terminals consists of two types of battery power: the main battery pack
that is accessible from the back panel, and the backup battery that resides inside the terminal.
The main battery powers the terminal. The internal backup battery charges off the main battery and
maintains the application data stored in RAM memory for up to 30 minutes when the terminal’s main battery pack is completely discharged or removed.
Battery Error Notification
If your terminal displays the following indicators, replace the main battery pack with a Honeywell Li-poly
or Li-ion battery pack.
• appears in the Title bar at the top of the touch screen
• The General Notification LED flashes red
• A Notification appears on the Tile bar at the bottom of the touch screen
2 - 1
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
!
RS232 Connector
Host Device
Power
Cable
Or
USB Connector
COMM Cable
Plug
Adapter
Cable Cup
Or
RS232, DEX A/V Connector
Dolphin 99EX
Dolphin 99EX
Plug
Adapter
Power
Cable
Client Device
Charging
Cup
Preliminary Draft 1/19/11
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Before Initial Use
Terminals are shipped with both batteries discharged of all power. The initial charging time for the main
battery pack is 4.5 hours for the standard 3.7V battery or 6 hours for the extended 3.7V battery. Connect
the terminal to one of the 99EX series charging peripherals to charge; see Peripherals for the 99EX on
page 3-2. Honeywell recommends charging the Dolphin terminal for at least 24 hours prior to initial use
to ensure the internal backup battery is fully charged.
Using the Charging/Communication Cables
Step 3. Boot the Terminal
The terminal begins booting as soon as power is applied. Do NOT press any keys or interrupt the boot
process. When the boot process is complete, the Home screen appears, and the terminal is ready for
use.
Note: The Home screen appears several times during the boot process. To ensure the boot process is complete,
wait several seconds before using the device.
2 - 2
Step 4. Set the Time Zone, Time, and Date
Preliminary Draft 1/19/11
On the Home screen, tap the line that displays the time and date.
The Clock Settings screen appears.
Tap the arrow to the right of the time zone to open the drop down men u. Select the appropiate time zone
from the menu. Set the correct time and date in the remaining fields and tap OK to save.
2 - 3
Home Screen
Text here indicates
the active program.
Icons here indicate the
status of various system
functions.
Preliminary Draft 1/19/11
After the Dolphin terminal initializes the first time, you see the Home screen.
You can also display the Home screen anytime by tapping .
TitleBar
The Title bar, located at the top of the screen, displays the active program, the status of various system
functions, and the current time. Tapping on the title bar provides access to the Horizontal Scroll. The
scroll provides access to additional programs and application screens. For additional information, see
Horizontal Scroll on page 2-7.
Note: Tapping the battery icon at the top of the screen does not open the Power applet with this version of Microsoft
Windows Embedded Handheld. Windows Embedded Handheld
Icons in the Title Bar
IndicatorMeaning
Synchronizing data
The terminal could not synchronize data with the workstation via ActiveSync.
New e-mail
2 - 4
Icons in the Title Bar
Preliminary Draft 1/19/11
IndicatorMeaning
New text message
New voicemail
New instant message
Vibrate on
Ringer off
Speakerphone on
Voice call in progress
Calls are forwarded
Call on hold
Missed call
Data call in progress
A battery error has occurred. Replace the main battery pack with a Honeywell Li-poly or Li-ion
battery pack.
Battery is has a full charge
Battery has a high charge
Battery has a medium charge
Battery has a low charge
Battery has a very low charge and requires charging
Terminal is running on external power. If a battery pack is installed, the battery is charging in the
background.
The terminal is not connected to external power. A battery is installed, but is def ectiv e; specifically,
its charge level cannot be measured.
No SIM card is installed
Active network connection
2 - 5
Icons in the Title Bar
Preliminary Draft 1/19/11
IndicatorMeaning
No active network connection
GPRS available
GPRS connecting
GPRS in use
HSDPA available
HSDPA connecting
HSDPA in use
EDGE available
EDGE connecting
EDGE in use
UMTS available
UMTS connecting
UMTS in use
Radio is off
The radio is not connected to a network.
The radio is connected. The bars indicate the signal strength.
No radio signal
The terminal is searching for a signal.
Wi-Fi is on, but device is not connected
Wi-Fi data call
Pending alarm
Bluetooth
2 - 6
Horizontal Scroll
The content of the
Horizontal scroll
changes according to
the open application.
The icons change according to the open application.
The T ask tray displa ys icons
for programs running in the
background.
The Tile bar displays icons you
use to open and close screens,
menues, and features.
Preliminary Draft 1/19/11
The Horizontal Scroll, located at the top of most application windows, provides access to additional
application screens. You can flick left or right on the scroll or tap each label on the scroll, until you get to
the desired screen. Tapping a label to the left or right of the center item brings new labels into view.
Note: Tap the Title bar to access the horizontal scroll if it is not visible on the screen.
Tile Bar
The Tile bar is located at the bottom of application windows.
Pop-Up Men us
With pop-up menus, you can quic kly choose an action f or a selected item. To access a pop-up menu, tap
and hold the stylus on the item name of the action you want to perf orm. When the menu appears, lift the
stylus, and tap the action you want to perform.
Tap anywhere outside the menu to close the menu without performing an action.
2 - 7
Selecting Programs
Preliminary Draft 1/19/11
To see the programs loaded on your terminal, tap to access the Start Menu. To open a
program, tap once on the program icon. To reposition an icon on the Start Menu, tap and hold the stylus
on the icon, and then drag the icon to the desired position.
File Explorer
You can also use the File Explorer to find files and organize these files into folders.
Tap > File Explorer .
Tap the Up button at the bottom of the screen to move up one level in the directory.
You can move files in File Explorer by tapping and holding on the item you want to move, and then tapping Cut or Copy on popup menu.
2 - 8
Navigate to the folder you want to move the file to, and then tap and hold a blank area of the window.
Preliminary Draft 1/19/11
Tap Paste on the pop-up menu.
Note: If there is no blank space available in the window, tap
menu using the down arrow, and then tap
Edit > Paste
Menu
on the command bar, navigate to the end of the
.
Search
The Search feature helps you quickly locate information. Tap > Search Phone .
Enter the text you want to find, select a data type, and then tap Go to start the search. Select Larger
than 64 KB in the Type drop-down field to quickly find information that is taking up storage space.
2 - 9
2 - 10
Preliminary Draft 1/19/11
3
Preliminary Draft 1/19/11
Hardware Overview
Standard Configurations for the 99EX
WLAN & WPAN
• Microsoft Windows Embedded Handheld
6.5 Classic
• OMAP3715 (1Ghz)
• 256MB RAM X 1GB Flash
• Four keyboard options
• 3.7V Li-poly or extended 3.7V Li-ion
rechargeable battery pack
• Adaptus Imaging Technology: N5603ER/
SR/HD or N5600ER/SR/HD image
engines
• 802.11a/b/g/n and Bluetooth
WLAN, WPAN, with GPS
• Microsoft Windows Embedded Handheld
6.5 Classic
• OMAP3715 (1Ghz)
• 256MB RAM X 1GB Flash
• Four keyboard options
• 3.7V Li-poly or extended 3.7V Li-ion
rechargeable battery pack
• Adaptus Imaging Technology: N5603ER/
SR/HD or N5600ER/SR/HD image
engines
• 802.11a/b/g/n and Bluetooth
•GPS
• 3.1 megapixel auto control color camera
WLAN, WPAN & Camera
• Microsoft Windows Embedded Handheld
6.5 Classic
• OMAP3715 (1Ghz)
• 256MB RAM X 1GB Flash
• Four keyboard options
• 3.7V Li-poly or extended 3.7V Li-ion
rechargeable battery pack
• Adaptus Imaging Technology: N5603ER/
SR/HD or N5600ER/SR/HD image
engines
• 802.11a/b/g/n and Bluetooth
• 3.1 megapixel auto control color camera
WLAN, WPAN, with GPS & Camera
• Microsoft Windows Embedded Handheld
6.5 Classic
• OMAP3715 (1Ghz)
• 256MB RAM X 1GB Flash
• Four keyboard options
• 3.7V Li-poly or extended 3.7V Li-ion
rechargeable battery pack
• Adaptus Imaging Technology: N5603ER/
SR/HD or N5600ER/SR/HD image
engines
• 802.11a/b/g/n and Bluetooth
•GPS
• 3.1 megapixel auto control color camera
WLAN, WPAN, & WWAN
• Microsoft Windows Embedded Handheld
6.5 Professional
• OMAP3715 (1Ghz)
• 256MB RAM X 1GB Flash
• Four keyboard options
• 3.7V Li-poly or extended 3.7V Li-ion
rechargeable battery pack
• Adaptus Imaging Technology: N5603ER/
SR/HD or N5600ER/SR/HD image
engines
• 802.11a/b/g/n, Bluetooth, and GSM/
HSPA+ or GSM/CDMA
WLAN, WPAN, & WWAN with GPS
• Microsoft Windows Embedded Handheld
6.5 Professional
• OMAP3715 (1Ghz)
• 256MB RAM X 1GB Flash
• Four keyboard options
• 3.7V Li-poly or extended 3.7V Li-ion
rechargeable battery pack
• Adaptus Imaging Technology: N5603ER/
SR/HD or N5600ER/SR/HD image
engines
• 802.11a/b/g/n, Bluetooth, and GSM/
HSPA+ or GSM/CDMA
•GPS
3 - 1
WLAN, WPAN, WWAN with GPS & Camera
Preliminary Draft 1/19/11
• Microsoft Windows Embedded Handheld 6.5 Professional
• OMAP3715 (1Ghz)
• 256MB RAM X 1GB Flash
• Four keyboard options
• 3.7V Li-poly or extended 3.7V Li-ion rechargeable battery pack
• Adaptus Imaging Technology: N5603ER/SR/HD or N5600ER/SR/HD image engines
• 802.11a/b/g/n, Bluetooth, and GSM/HSPA+ or GSM/CDMA
•GPS
• 3.1 megapixel auto control color camera
Some configurations of the 99EX terminal are available with an external housing made of plastic that is
specifically designed for the healthcare industry. For more inf ormation, see Healthcare Housing on page
3-12.
Peripherals for the 99EX
Each of the following items is sold separately to enhance the capabilities of your Dolphin terminal.
Dolphin 99EX HomeBase™ Device
The Dolphin 99EX HomeBase device is a charging and communication cradle supporting both RS232
and USB communications, which enables the terminal to interface with the majority of PC-based enterprise systems. This device also contains an auxiliary battery well that charges a spare Honeywell Li-poly
or extended Li-ion battery.
For more information, see Dolphin 99EX HomeBase Device on page 12-1.
Dolphin 99EX Mobile Base™ Device
The Dolphin 99EX Mobile Base device is a charging and communication cradle designed specifically for
in-premise and in-transit data collection applications. It features a flexible mounting bracket and a cigarette lighter adapter to adapt it to your environment.
The serial connector supports RS232 communication and power out to peripheral devices, such as
handheld scanners. The USB connector is a high-speed 2.0v compliant host port. Using a USB cable,
you can connect the base to a peripheral device, such as a memory stick or printer.
For more information, see Dolphin 99EX Mobile Base Device on page 14-1.
Dolphin 99EX eBase™ Device
The Dolphin 99EX eBase device enables a single 99EX mobile computer to commuicate with a host
device over USB and Ethernet network. This device also contains an auxiliary battery well that charges a
spare Honeywell Li-poly or extended Li-ion battery.
For more information, see Dolphin 99EX eBase Device on page 13-1.
3 - 2
Dolphin 99EX Net Base™ Device
Preliminary Draft 1/19/11
The Dolphin 99EX Net Base device enables up to four 99EX mobile computers to communicate with a
host device over an Ethernet network. In addition, the Net Base provides a second RJ45 Ethernet port for
connection to an additional device such as a printer, workstation, eBase, or another Net Base.
For more information, see Dolphin 99EX Net Base Device on page 16-1.
Dolphin 99EX Net Rack™ Device
The Dolphin 99EX Net Rack device enables up to thirty 99EX mobile computer to communicate with a
host device over an Ethernet network.
For more information, please consult the Dolphin 99EX Net Rack and Charge Rack User’s Guide.
Dolphin 99EX ChargeBase
The Dolphin 99EX ChargeBase is a 4-slot charging cradle that holds, powers, and charges terminals.
For more information, see Dolphin 99EX ChargeBase Device on page 15-1.
Dolphin 99EX ChargeRack™ Device
The Dolphin 99EX Charge Rack device is a 30-slot charging ra ck that holds, powers, and charges terminals.
For more information, please consult the Dolphin 99EX Net Rack and Charge Rack User’s Guide.
Dolphin 99EX QuadCharger™ Device
The Dolphin 99EX QuadCharger device is a 4-slot charging station for 99EX standard Li-poly or
extended Li-ion battery packs.
For more information, see Dolphin 99EX QuadCharger Device on page 17-1.
Accessories for the 99EX
Each of the following items is sold separately to enhance your terminal’s capabilities.
Note: When using accessories where the terminal is worn on the body, the terminal’s touch panel must face away
from the body.
Dolphin 99EX Mobile Charger
The Dolphin 99EX Mobile Charger is a charging cable that connects the terminal directly to a 12 V olt DC
power source, such as a cigarette lighter port inside a vehicle, eliminating the need for a cradle. Intelligent battery technology on-board the terminal ensures proper charging. The Dolphin 99EX Mobile Charger is an ideal low-cost charging solution for in-transit mobile applications.
3 - 3
Loading...
+ 67 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.