Honeywell 9700L0P, 9700LUP Users Manual

Download

Dolphin

with Windows Mobile® 6.5

9700 Mobile Computers

User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII.

Web Address: www.honeywellaidc.com

Trademarks

Dolphin, Dolphin RF, HomeBase, Mobile Base, and QuadCharger are trademarks or registered trademarks of Hand Held Products, Inc. or Honeywell International Inc.

Microsoft, Windows, Windows Mobile, Windows CE, Windows NT, Windows 2000, Windows ME, Windows XP, ActiveSync, Outlook, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation.

Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are the property of their respective owners.

Patents

Please refer to the product packaging for a list of patents.

Other Trademarks

The Bluetooth trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to Honeywell.

Declaration for the Specification

FCC ID: HD59700LUP for 802.11 a/b/g +BT+GSM FCC ID: HD59700LOP for 802.11 a/b/g +BT

IC ID: 1693B-9700LUP for 802.11 a/b/g +BT+GSM IC ID: 1693B-9700LOP for 802.11 a/b/g +BT

Table of Contents

Chapter 1 - Agency Information

Label Locations ....................................................................................................................1-1

LED Safety Statement .........................................................................................................1-2

Infrared LED Safety Statement ............................................................................................1-2

UL and cUL Statement.........................................................................................................1-2

Approvals by Country...........................................................................................................1-2

R&TTE Compliance Statement—802.11a/b/g, Bluetooth, and/or GSM...............................1-3

Dolphin RF Terminal—802.11a/b/g, Bluetooth, and/or GSM ...............................................1-3

For European Community Users .........................................................................................1-4

Waste Electrical and Electronic Equipment Information ......................................................1-4

Chapter 2 - Getting Started

Out of the Box ......................................................................................................................2-1

Today Screen.......................................................................................................................2-3

Navigation Bar .....................................................................................................................2-3

Command Bar ......................................................................................................................2-3

Icons in the Navigation Bar ..................................................................................................2-4

Pop-Up

Chapter 3 - Hardware Overview

Peripherals for the 9700.......................................................................................................3-2

Accessories for the 9700 .....................................................................................................3-3

Front Panel: 9700 ................................................................................................................3-4

Back Panel: 9700 ................................................................................................................3-6

Side Panels:

Bottom Panel: 9700 ...........................................................................................................3-10

Using the Touch Panel.......................................................................................................3-11

Healthcare Housing ...........................................................................................................3-12

Batteries .............................................................................................................................3-13

Resetting the Terminal .......................................................................................................3-16

Suspend

Menus

Standard Configurations for the 9700 ............................................................................3-1

Front Panel Features for the 9700 .................................................................................3-5

Back Panel Features for the 9700..................................................................................3-7

Left Side .........................................................................................................................3-8

Right Side ......................................................................................................................3-8

Installing a Memory Card ...............................................................................................3-9

Installing a SIM

I/O Connector ...............................................................................................................3-10

Installing a Screen Protector ........................................................................................3-11

Main Battery Pack ........................................................................................................3-13

Internal Backup Battery ................................................................................................3-14

Managing Battery Power ..............................................................................................3-14

Checking Battery Power...............................................................................................3-15

Soft Reset (Warm Boot) ...............................................................................................3-16

Hard Reset (Cold Boot) ................................................................................................3-16

.....................................................................................................................2-5

9700

................................................................................................................3-8

Card

......................................................................................................3-9

Mode

...................................................................................................................3-16

iii

Chapter 4 - Using the Scan Image Engine

Overview.............................................................................................................................. 4-1

Angled Imaging.............................................................................................................. 4-1

Image Engine Specifications ............................................................................................... 4-1

Laser Specifications ............................................................................................................ 4-2

Supported Bar Code Symbologies ..................................................................................... 4-2

Decoding ............................................................................................................................. 4-3

To Decode a Bar

Code

.................................................................................................. 4-3

Aiming Options .............................................................................................................. 4-4

Capturing Images ................................................................................................................ 4-5

Taking an Image ............................................................................................................ 4-5

Uploading Images.......................................................................................................... 4-6

Chapter 5 - Using the Keyboards

Available Keyboards ............................................................................................................ 5-1

Keyboard Combinations ................................................................................................ 5-1

Common Buttons ........................................................................................................... 5-1

Using the Function Keys...................................................................................................... 5-2

Using the Modifier Keys ...................................................................................................... 5-3

Using the Navigation Keys .................................................................................................. 5-3

31-Key Numeric Keyboard .................................................................................................. 5-4

31-Key Keyboard Combinations .................................................................................... 5-5

45-Key QWERTY Keyboard ................................................................................................ 5-7

45-Key Keyboard Combinations .................................................................................... 5-8

Chapter 6 - System Settings

Overview.............................................................................................................................. 6-1

Clock & Alarms .................................................................................................................... 6-2

............................................................................................................................................. 6-2

Personal Menu .................................................................................................................... 6-3

Buttons........................................................................................................................... 6-4

Input............................................................................................................................... 6-5

System

Menu.......................................................................................................................

About ............................................................................................................................. 6-8

Backlight ........................................................................................................................ 6-8

Certificates..................................................................................................................... 6-9

Encryption...................................................................................................................... 6-9

Error Reporting .............................................................................................................. 6-9

External GPS ............................................................................................................... 6-10

Managed Programs ..................................................................................................... 6-10

Memory........................................................................................................................

RIL ............................................................................................................................... 6-12

Power........................................................................................................................... 6-13

Regional Settings......................................................................................................... 6-13

Remove Programs....................................................................................................... 6-13

Screen ......................................................................................................................... 6-15

Task

Manager..............................................................................................................

6-7

6-11

6-16

Chapter 7 - Communication

Connections

Menu...............................................................................................................

Using the IrDA Port.............................................................................................................. 7-2

IrDA Port Location ......................................................................................................... 7-2

Sending Data ................................................................................................................. 7-2

Receiving Data .............................................................................................................. 7-3

Connections Manager ......................................................................................................... 7-4

To Access the Connections

Manager............................................................................

Task Tab........................................................................................................................ 7-4

Advanced Tab................................................................................................................ 7-5

Dolphin Wireless Manager .................................................................................................. 7-6

Dolphin Wireless Manager Window............................................................................... 7-6

Enabling the Radios....................................................................................................... 7-6

Accessing Radio Configuration Utilities ......................................................................... 7-7

ActiveSync Communication ................................................................................................. 7-8

Installing Additional Software ............................................................................................ 7-10

Adding Programs to the Terminal Using ActiveSync ................................................... 7-10

Adding Programs Directly from the Internet................................................................. 7-11

9700 COM Port Assignment Table .................................................................................... 7-12

Chapter 8 - Working with GSM

Overview.............................................................................................................................. 8-1

Quad Band Antenna ...................................................................................................... 8-1

SIM Card Installation ........................................................................................................... 8-2

Enabling the GSM

Radio

..................................................................................................... 8-4

Voice Communication.......................................................................................................... 8-5

Audio

Modes..................................................................................................................

Volume Control .............................................................................................................. 8-5

Accessing the Dialer Window ........................................................................................ 8-5

Dialing

............................................................................................................................ 8-5

Sending Calls................................................................................................................. 8-6

Ending Calls................................................................................................................... 8-6

Keyboard Combinations for

Calls ..................................................................................

View Options.................................................................................................................. 8-6

Setup Options ...................................................................................................................... 8-7

Data Communication ........................................................................................................... 8-8

Establishing Data Communication................................................................................. 8-8

Ending the Data Connection........................................................................................ 8-10

Roaming ............................................................................................................................

Chapter 9 - Working with the Bluetooth Radio

Enabling the Bluetooth

Connecting to Other Bluetooth Devices .............................................................................. 9-2

Pairing and Trusted Devices ............................................................................................... 9-4

Types of Devices and Services ........................................................................................... 9-5

Connecting to Bluetooth Printers ......................................................................................... 9-6

Connecting to Bluetooth Headsets ...................................................................................... 9-6

Transferring Files................................................................................................................. 9-7

Making the Terminal

Radio

.............................................................................................. 9-1

Discoverable ......................................................................................

7-1

7-4

8-5

8-6

8-11

9-8

Selecting COM Ports ........................................................................................................... 9-8

Chapter 10 - Working with GPS

Overview............................................................................................................................ 10-1

Assisted GPS Support ....................................................................................................... 10-1

Powering the GPS Module ................................................................................................ 10-1

Communication Ports ........................................................................................................ 10-2

Selecting the Port ........................................................................................................ 10-2

COM7 .......................................................................................................................... 10-2

GPS Intermediate

Driver..............................................................................................

GPS Demo ........................................................................................................................ 10-3

Chapter 11 - Dolphin 9700 HomeBase Device

Overview............................................................................................................................ 11-1

Parts and Functions........................................................................................................... 11-2

Power ................................................................................................................................ 11-4

Serial Connector ................................................................................................................ 11-5

Charging the Main Battery ................................................................................................. 11-6

To Power a Terminal and Charge its Main Battery...................................................... 11-6

Charging a Spare Battery in the Auxiliary Battery Well ............................................... 11-6

Communication.................................................................................................................. 11-7

Connecting the Communication Cables ...................................................................... 11-7

Establishing Communication ....................................................................................... 11-7

Communicating with the Dolphin Terminal ........................................................................ 11-7

Verifying Data Transfer................................................................................................ 11-8

RS232 Communications

Cables........................................................................................

RS232 Pin Configuration ............................................................................................. 11-9

Mounting .......................................................................................................................... 11-10

Desk Mounting........................................................................................................... 11-10

Wall Mounting ............................................................................................................ 11-11

Chapter 12 - Dolphin 9700 Mobile Base Device

Overview............................................................................................................................ 12-1

Front Panel ........................................................................................................................ 12-2

Bottom Panel ..................................................................................................................... 12-3

Powering the Dolphin Terminal ......................................................................................... 12-4

Charging the Dolphin Terminal .......................................................................................... 12-4

Mounting ............................................................................................................................ 12-5

Power ................................................................................................................................ 12-6

Establishing Communication ............................................................................................. 12-7

Connecting the Communication Cables ...................................................................... 12-7

Establishing ActiveSync Communication..................................................................... 12-7

Chapter 13 - Dolphin 9700 ChargeBase Device

Overview............................................................................................................................ 13-1

Parts and Functions........................................................................................................... 13-2

Supplying Power................................................................................................................ 13-3

10-2

11-9

Inserting and Removing Terminals .................................................................................... 13-4

Charging Terminals ........................................................................................................... 13-4

Mounting ............................................................................................................................ 13-5

Chapter 14 - Dolphin 9700 QuadCharger Device

Overview............................................................................................................................ 14-1

Parts and Functions........................................................................................................... 14-2

Supplying Power................................................................................................................ 14-3

Inserting and Removing Battery Packs ............................................................................. 14-4

Charging Batteries ............................................................................................................. 14-4

Using the Battery Analyzer ................................................................................................ 14-5

Mounting ............................................................................................................................ 14-6

Desk Mounting............................................................................................................. 14-6

Wall Mounting .............................................................................................................. 14-7

Troubleshooting ................................................................................................................. 14-8

Chapter 15 - Customer Support

Product Service and

Online Product Service and Repair Assistance ........................................................... 15-1

Technical Assistance ......................................................................................................... 15-2

Online Technical Assistance........................................................................................ 15-2

Limited Warranty ............................................................................................................... 15-3

How to Extend Your Warranty ..................................................................................... 15-4

Repair...............................................................................................

15-1

vii

viii

Agency

Dolphin 9700 terminals meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Please read these guidelines carefully before using your Dolphin terminal.

Information

Label Locations

Dolphin 9700

Laser Safety Label

If the following label is attached to your product, it indicates the product contains an engine with a laser aimer:

Image Engines with Integrated Laser Aimers

LASER LIGHT. Class 2 Laser

IEC60825-1: 1993+A1+A2. Output: 650nM. Complies with and 1040.11 except Laser Notice

Laser Eye Safety Statement: This device has been tested in accordance with and complies with IEC60825-1: 1993+A1+A2 and 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. LASER LIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PRODUCT, 1.0 mW MAX OUTPUT: 650nM.

Caution! Use of controls or adjustments or performance of

may result in hazardous radiation exposure.

Do not

Product.

No. 50,

Compliance

stare into

for

deviations pursuant

dated June

1.0 21

beam.

CFR

24, 2007.

MAX

1040.10 to

Label

procedures

other than those specified herein

1 - 1

LED Safety Statement

The LED output on this device has been tested in accordance with IEC60825-1 LED safety and certified to be a Class 1 LED device.

The maximum power outputs for each diode are as follows:

• Illumination LED: 194.0 uW, wavelength: 626nm+/-30nm

• Aimer laser (5300 engine): 360.1 uW, wavelength: 655nm

• Aimer LED (5100 engine): 81.6 uW, wavelength: 526nm+/-30nm

Infrared LED Safety Statement

Caution! Do not view directly with optical instruments.

The maximum power outputs for the IR LED is 145.1 uW. LEDs are pulsed at a frequency of 115,200 Hz with a duty cycle of 18.75% where the “ON” time of a single pulse is 1.6275 x 10

-6

seconds.

UL and cUL Statement

UL and cUL listed: UL60950-1 and CSA C22.2 No. 60950-1-03.

Approvals by Country

Country

EMC, Radio, & SAR

Safety

U.S.A.

Canada

European Community/CE

FCC Part 15, Subpart B FCC Part 15, Subpart C, 15.247 FCC Part 15, Subpart E FCC Part 22H FCC Part 24E FCC SAR OET 65 Supplement C

ICES-003 (Class B) RSS 132 RSS 133 RSS 210

EN300328 EN301893 EN55022 EN55024 EN301489-1 EN301489-7/24 EN301489-17 EN300328 3GPPTS 51.010-1 EN301511 EN301908 EN50360 EN50361 EN50371 EN50392 IEC6220-1 and IEC6220-2 EN300440

UL60950-1

cUL60950

EN/IEC60950-1 EN/IEC60825-1

This Class 2 Laser Product is in accordance with the requirements of IEC 60825-1 Ed. 1.2 Clause 6.2(a).

1 - 2

R&TTE Compliance Statement—802.11a/b/g, Bluetooth, and/or GSM

Dolphin RF terminals are in conformity with all essential requirements of the R&TTE Directive (1999/5/ EC).

This product is marked with in accordance with the Class II product requirements specified in the R&TTE Directive. In addition, this product complies to 2006/95/EC Low Voltage Directive supplied

with the recommended power supply. Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.

The equipment is intended for use throughout the European Community; PAN European Frequency Range: 2.402–2.480 GHz. Restrictions for use in France are as follows:

• Indoor use: Maximum power (EIRP*) of 100 mW for the entire 2.400–2.4835 GHz

• Outdoor use: Maximum power (EIRP*) of 100 mW for the 2.400–2.454 GHz band & maximum power

(EIRP*) of 10 mW for the 2.454–2.483 MGHz band.

• 5Ghz band: UNII (Unlicensed National Information Infrastructure) or band1 (5.150 to 5.250 GHz) is

restricted to indoor use only. Any other use will make the operation of the device illegal. For further information, please contact: Honeywell Imaging & Mobility Europe BV

Nijverheidsweg 9 5627 BT Eindhoven The Netherlands

when

Dolphin RF Terminal—802.11a/b/g, Bluetooth, and/or GSM

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. If necessary, the user should consult the dealer or an experienced radio/television technician for

additional suggestions. The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Our company is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by our company. The correction is the responsibility of the user. Use only shielded data cables with this system.

accordance for compliance could void the user’s authority to operate the equipment.

CAUTION!

with FCC 15.21, changes or modifications not expressly approved by the party responsible

Any changes or modifications not expressly approved by the grantee of this device could void

the user's authority to operate the equipment.

1 - 3

Canadian Compliance

This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide is subject to licensing.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

maximum

shielding. Equipment (or its transmit antenna) installed outdoors

For European Community Users

Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Waste Electrical and Electronic Equipment Information

This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, if not properly disposed.

In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way.

The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal.

If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration.

You may also contact your supplier for more information on the environmental performances of this product.

Pacemakers, Hearing Aids and Other Electrically Powered Devices

Most manufacturers of medical devices adhere to the IEC 601-1-2 standard. This standard requires devices to operate properly in an EM Field with a strength of 3V/m over a frequency range of 26 to 1000MHz. The maximum allowable field strength emitted by the Dolphin terminal is 0.3V/m according to Subpart B of Part 1 of the FCC rules. Therefore, the RF from the Dolphin terminal has no effect on medical devices that meet the IEC specification.

Microwaves

The radio in the Dolphin RF terminal operates on the same frequency band as a microwave oven. Therefore, if you use a microwave within range of the Dolphin RF terminal you may notice performance degradation in your wireless network. However, both your microwave and your wireless network will continue to function. The Dolphin Batch terminal does not contain a radio, and therefore, is not affected by microwave ovens.

1 - 4

For United State of America Users

For body worn operation, this device has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and the positions the handset a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

Operation on the 5.15-5.25GHz frequency band is restricted to indoor use only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the potential for harmful interference to co-channel Mobile Satellite Systems.

Using Your Phone With a Hearing Aid Device

Your Dolphin 9700 device is compliant with the FCC Hearing Aid Compatibility (HAC) requirements.

When some wireless phones are used near some hearing devices (hearing aids and cochlear

implants), users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than others to this interference noise, and phones also vary in the amount of interference they generate. The wireless telephone industry has developed ratings for some of their mobile phones, to assist hearing-device users in finding phones that may be compatible with their hearing devices. Not all phones have been rated. Phones that have been rated have a label on the box. Your Dolphin 9700 has been tested for hearing aid device compatibility and has an M3 and/or T3 rating.

These ratings are not guarantees. Results will vary, depending on the level of immunity of your hearing device and the degree of your hearing loss. If your hearing device happens to be vulnerable to interference, you may not be able to use a rated phone successfully. Trying out the phone with your hearing device is the best way to evaluate it for your personal needs.

M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference with hearing devices than phones that are not labeled. M4 is the better/higher of the two ratings. T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to be more usable with a hearing device’s telecoil (“T Switch” or “Telephone Switch”) than unrated phones. T4 is the better/higher of the two ratings. (Note that not all hearing devices contain telecoils.) The more immune your hearing aid device is, the less likely you are to experience interference noise from your wireless phone. Hearing aid devices should have ratings similar to those of phones. Ask your hearing health-care professional for the rating of your hearing aid.

Hearing devices may also be measured for immunity to this type of interference. Your hearing device manufacturer or hearing health professional may help you find results for your hearing device. The more immune your hearing aid is, the less likely you are to experience interference noise from wireless devices.

For additional information about the FCC's actions with regard to hearing aid compatible wireless devices and other steps the FCC has taken to ensure that individuals with disabilities have access to telecommunications services, please go to www.fcc.gov/cgb/dro.

2 - 1

Getting

Started

Out of the Box

Verify that the carton contains the following items:

• Dolphin 9700 mobile computer (the terminal)

• Main battery pack (7.4V Li-ion)

• Quick Start Guide

Note: If you ordered accessories for your terminals, verify that they are also included with the order.

Be sure to keep the original packaging in the event that the Dolphin terminal should need to be returned for service. For details, see Product Service and Repair on page 15-1.

Step 1. Install the Main Battery Pack

New Image Required

We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.

1 - 6

Step 2. Charge the Main and Backup Batteries

The power supply for Dolphin terminals consists of two types of battery power: the main battery pack installed on the back panel and the backup battery that resides inside the terminal.

The main battery powers the terminal. The internal backup battery charges off the main battery and maintains the application data stored in RAM memory for up to 30 minutes when the terminal’s main battery pack is completely discharged or removed.

Before Initial Use

Time to Charge

We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell

peripherals, cables, or power adapters may cause damage not covered by the warranty.

Terminals are shipped with both batteries discharged of all power. Charge the main battery pack for a minimum of 4 hours before initial use.

The initial charging time for the main battery pack is 4 hours, and 8 hours for the internal backup battery. Connect the terminal to one of the 9700 series charging peripherals to charge; see

Peripherals for the 9700 on page 3-2.

Step 3. Boot the Terminal

The terminal begins booting as soon as power is applied and runs by itself. Do NOT press any keys or interrupt the boot process. Only tap the screen when prompted.

When the boot process is complete, the Today screen appears, and the terminal is ready for use.

Note: Because, the Today screen appears a number of times during the boot process, wait a few seconds before

tapping anything on the Today screen.

Step 4. Set the Time and Date

You need to re-set the time and date after every hard reset of the terminal. On the Today screen, tap the line that displays the time and date,

Windows Mobile 6.5, Professional Windows Mobile 6.5,

Classic

The Clock Settings screen appears.

The time zone defaults to GMT-5 Eastern US; tap the arrow to the right of GMT-5 Eastern US to select another time zone. Set the correct time and date in the remaining fields and tap OK to save.

2 - 2

Today Screen

After the Dolphin terminal initializes the first time, you see the Today screen.

Windows Mobile 6.5, Professional Windows Mobile 6.5,

Classic

You can also display the Today screen anytime by tapping Start and then Today.

Navigation Bar

The Navigation bar, located at the top of the screen, displays the active program and current time. It also provides access to the Start menu, which allows you to open programs and access the system settings.

Start menu: Grants

access to system

functions.

Icons here indicate the status of various system functions.

Command Bar

The Command bar is located at the bottom of application windows.

Menus change according to the open application.

The Task tray displays icons for programs running in the background.

2 - 3

Icons in the Navigation Bar

Indicator Meaning

The terminal could not synchronize data with the workstation via ActiveSync.

New e-mail or text message (SMS)

New voicemail

New instant message

Ringer off

Voice call

Voice call in progress

Calls are forwarded

Call on hold

Missed call

Data call in progress

Battery levels (1–4). Tap this icon to open the Power system setting and see the charge percentage (see page 3-15).

4 - 2

Critical battery – The charge percentage is at the critical battery point set in the registry (the default is 10%). For details about the critical battery point, (see page 3-14).

Tap this icon to open the Power system setting and see the charge percentage (see page 3-15).

Terminal is running on external power. (If a battery pack is installed, the battery is charging in the background.)

The terminal is not connected to external power. A battery is installed, but is defective; specifically, its charge level cannot be measured.

No SIM card is installed

GPRS available

GPRS connected

EDGE available

Icons in the Navigation Bar

Indicator Meaning

EDGE connected

Roaming

Radio is disabled

The radio is not connected to a network.

Radio connected

No radio signal

The terminal is searching for a signal.

Radio signal strength

Wi-Fi on

Wi-Fi data call

Pending alarm

Bluetooth

Pop-Up Menus

With pop-up menus, you can quickly choose an action for a selected item. To access a pop-up menu, tap and hold the stylus on the item name of the action you want to perform. When the menu appears, lift the stylus, and tap the action you want to perform.

Tap anywhere outside the menu to close the menu without performing an action.

2 - 5

Selecting Programs

To see the programs loaded on your terminal, tap Start to access the Start Menu. To open a program, tap once on the program icon.

To move an icon to the top of the Start Menu, tap and hold the stylus on the icon you want to move. Tap on Move to Top. To move the icon down, tap and hold the stylus on the icon. Tap on Move Down.

File Explorer

You can also use the File Explorer to find files and organize these files into folders.

Tap

Start

> File Explorer .

Tap the Up button at the bottom of the screen to move up one level in the directory.

You can move files in File Explorer by tapping and holding on the item you want to move, and then tapping

Cut or Copy and Paste on popup menus.

The Search feature helps you quickly locate information. Tap Start > Search Phone . Enter the text you want to find, select a data type, and then tap Go to start the search. To quickly find

information that is taking up storage space, select Larger than 64 KB in the Type drop-down field.

6 - 2

Hardware

Standard Configurations for the 9700

WLAN & WPAN

• Microsoft Windows Mobile 6.5 Classic

• Marvell® PXA270 624 MHz

• 256MB SDRAM X 1GB Flash

• Two in-mold, hard-top keyboard options

• 1620mAh extended life main battery

• Adaptus Imaging Technology: 5100SR/SF or 5300SR/SF/HD image

• 802.11a/b/g and Bluetooth

WLAN, WPAN, & WWAN

• Microsoft Windows Mobile 6.5 Professional

• Marvell PXA270 624 MHz

• 256MB SDRAM X 1GB Flash

• Two in-mold, hard-top keyboard options

• 1620mAh extended life main battery

• Adaptus Imaging Technology: 5100SR/SF or 5300SR/SF/HD image

• 802.11a/b/g, Bluetooth, and GSM/GPRS

WLAN, WPAN, & WWAN with GPS

• Microsoft Windows Mobile 6.5 Professional

• Marvell PXA270 624 MHz

• 256MB SDRAM X 1GB Flash

• Two in-mold, hard-top keyboard options

• 1620mAh extended life main battery

• Adaptus Imaging Technology: 5100SR/SF or 5300SR/SF/HD image

• 802.11a/b/g, Bluetooth, and GSM/GPRS

• GPS

Some configurations of the 9700 terminal are available with an external housing made of plastic that is specifically designed for the healthcare industry. For more information, see Healthcare Housing on page

3-12.

Overview

engines

3 - 1

Peripherals for the 9700

Each of the following items is sold separately to enhance the capabilities of your Dolphin terminal.

Dolphin 9700 HomeBase™ Device

The Dolphin 9700 HomeBase device, a charging and communication cradle, supports both RS232 and USB communications, which enable it to interface with the majority of PC-based enterprise systems. This device also contains an auxiliary battery well that charges a spare Li-ion battery.

For more information, see Dolphin 9700 HomeBase Device on page 11-1.

Dolphin 9700 Mobile Base™ Device

The Dolphin 9700 Mobile Base device, a charging and communication cradle, designed specifically for in-premise and in-transit data collection applications. It features a flexible mounting bracket, and a cigarette lighter adapter or power cable to adapt it to your environment.

The serial connector supports RS232 communication and power out to peripheral devices, such as handheld scanners.

For more information, see Dolphin 9700 Mobile Base Device on page 12-1.

Dolphin 9700 ChargeBase

The Dolphin 9700 ChargeBase is a 4-slot charging cradle that holds, powers, and charges terminals. For more information, see Dolphin 9700 ChargeBase on page 3-2.

Dolphin 9700 Net Base

The Dolphin 9700 Net Base is a 4-slot charging/communication cradle that holds, powers, charges, and communicates with terminals. Ethernet communication occurs via statically and

dynamically-assigned

addresses. For more information about the Dolphin 9700 Net Base, please consult the Dolphin Net Base Quick Start

Guide.

Dolphin 9700 QuadCharger™ Device

The Dolphin 9700 QuadCharger device is a 4-slot charging station for 9700 Li-ion battery packs. The 4th slot features a battery analyzer that completely resets and re-calibrates a battery and displays its resulting capacity.

For more information, see Dolphin 9700 QuadCharger Device on page 14-1.

3 - 2

Accessories for the 9700

Each of the following items is sold separately to enhance your terminal’s capabilities.

Note: When using accessories where the terminal is worn on the body, the terminal’s touch panel must face away

from the body.

Dolphin 9700 Mobile Charger

The Dolphin 9700 Mobile Charger is a charging cable that connects the terminal directly to a 12 Volt DC power source, such as a cigarette lighter port inside a vehicle, eliminating the need for a cradle. Intelligent battery technology on-board the terminal ensures proper charging. The Dolphin 9700 Mobile Charger is an ideal low-cost charging solution for in-transit mobile applications.

Dolphin 9700 Mobile Mount

The Dolphin 9700 Mobile Mount, which holds a Dolphin terminal securely in place inside a vehicle, is an ideal, low-cost alternative to the Dolphin 9700 Mobile Base when communications are not required. When used in conjunction with the Dolphin 9700 Mobile Charger, the Dolphin 9700 Mobile Mount creates a complete mounting and charging solution for in-transit applications. The entire kit includes an adjustable vehicle mounting bracket.

Communication/Charging Cables

Dolphin communication/charging cable kits are an all-in-one solution for mobile applications. Each cable kit powers the terminal, charges its main battery, and communicates with host or peripheral devices without the need for a cradle. Cable kits can support RS232 or USB communications and are available with U.K. or European power cords.

Protective Holster

Holsters provide convenient storage for terminals and protect them from damage in mobile environments. Both holsters feature a front pocket that holds an extra battery, a side pocket to hold an extra stylus, and a belt loop to secure the holster to a belt.

Protective Enclosure

Protective enclosures help seal and protect terminals from damage while providing full access to all terminal parts and features. These

enclosures

feature a swivel clip on the back that enables you to secure

the enclosure to a belt. Enclosures also come with an adjustable shoulder strap for added convenience.

Stylus Kits

There are two stylus kits: one contains three styli and the other includes additional coiled tethers to secure the stylus to the terminal, which helps prevent loss.

Li-ion Battery Pack

The 7.4V Li-ion rechargeable battery pack provides the main power for the terminal.

3 - 3

Front Panel: 9700

Key

Power

Front

Speaker

Navigation Keys

Indicator

Touch Panel Display

Recessed Keyboard

I/O

Connector

For a description of each callout, see Front Panel Features for the 9700 on page 3-5.

SCAN

LED

Key

3 - 4

Front Panel Features for the 9700

Blue Modifier Key

Front Speaker

I/O Connector

Indicator LED

Navigation Keys

Power Key

Recessed Keyboard

Red Modifier Key

SCAN Key

Touch Panel Display

See Using the Modifier Keys on page 5-3.

The front speaker is the receiver for handset voice calls. The speaker provides audio input to the terminal when a headset is not plugged into the I/O Connector, page 3-10. When a headset is plugged in, the terminal defaults to the microphone on the headset.

See I/O Connector on page 3-10.

The light emitting diode (LED) located at the top of the LCD display flashes and illuminates during resets and scanning/imaging. This LED can be programmed by various software applications.

The centrally-located navigation keys enable you to move and position the cursor through software programs. The up and down arrows are programmed to perform specific functions when pressed in combination with the Blue and Red modifier keys. For more details, see Using

the Navigation Keys on page 5-3.

The red power key puts the terminal in suspend mode or wakes the terminal from suspend mode. See Suspend Mode on page 3-16.

There are two keyboard options: a 31-key numeric keyboard or a 45-key QWERTY keyboard. For a complete overview of each keyboard, see Using the Keyboards on page 5-1.

See Using the Modifier Keys on page 5-3.

The SCAN key is centrally located for easy access with the right or left hand. When pressed, the SCAN key activates the scanner/imager. The SCAN key also functions as a system wakeup control for the terminal.

The color 3.7 inch liquid crystal display (LCD) touch panel is covered with an industrial, protective lens for greater durability. The video graphic array (VGA) display resolution is 480 X 640.

The 262K color (18 bit RGB) LCD uses thin film transistor (TFT) technology. The tough panel backlight illuminates when the screen is touched, but not when the Backlight key is pressed. For more information, see Backlight on page 6-8.

The touch panel can be activated by the stylus information, see Using the Touch Panel on page 3-11.

(included

with the terminal) or a finger. For more

3 - 5

Back Panel: 9700

Image/Scan Engine

Window

Color Camera

Flashlight/Camera Flash

Color

Rear Speaker

Battery

IrDA

Port

Stylus Slot

For a description of each callout, see Back Panel Features for the 9700 on page 3-7.

Camera

Door

3 - 6

Back Panel Features for the 9700

Battery Door

Color Camera

Fastener for the Stylus Tether

Image/Scan Engine Window

Flashlight/Camera Flash

Memory Card Sockets

Rear Speaker

Stylus Slot

The battery door secures the Li-ion battery pack in the terminal’s battery well. For more information, see Batteries on page 3-13.

Color camera with 2.0-Megapixels Resolution (1600 x 1200 pixel), Auto Focus and LED flash.

Stylus tethers can be purchased separately to help prevent accidental loss when the sylus is not stored in the stylus slot. A stylus tether is a coiled, elastic cord that tethers the stylus to the terminal. Secure one end of the cord to the back panel of the terminal and the other end to the stylus.

The available image engines read and decode linear, stacked linear (e.g., PDF417), and 2D matrix bar code symbologies. The available image engines contain a laser aimer for greater accuracy. The laser apertures for the imaging engines’ laser aimers are contained behind this window. For more details, see Using the Scan Image Engine on page 4-1.

The flashlight/camera flash is located on the back panel of the terminal. The flashlight is turned on and off by pressing the Blue key + SCAN key. The flash is activated when using the terminal’s color camera.

These sockets

provide

the user with the option to industry-standard microSD or microSDHC memory interfaces. The expansion sockets are located under the main battery in the battery well.

When the battery pack and battery door are properly installed, the memory card is sealed against moisture and particle intrusion, read/write data is stored securely, and the terminal’s environmental rating is preserved; see Installing a Memory Card on page 3-9.

The integrated speaker sounds audio signals as you scan bar code labels and enter data. The integrated speaker also supports playback of wave and MP3 files, software mixer, WWAN/ GSM audio, and VoIP. The operating frequency range is 600-3000Hz at >90dB.

The stylus is used to operate the touch panel. The back panel of the terminal features a storage slot to hold the stylus when not in use. The stylus features a special tip for added accuracy and ease of use.

expand

the terminal’s

memory

capacity using

3 - 7

Side Panels: 9700

The left and the right side panels contain different features.

Left Side

Left Button

IrDA Port

Right Side

Right Button

Volume Button

Button

Left

When pressed, the Left Button key activates the scanner/imager.

The IrDA port enables infrared communication. The maximum data transfer speed is 115 kbps.

Note: The infrared LED aperture is located behind the scan engine window.

For more information about using this port, see Using the IrDA Port on page 7-2.

IrDA Port

Right Button

When pressed, the Right Button key activates the scanner/imager.

Press the up or down arrows on the volume button to raise or lower the volume of the main speaker.

Slot

Stylus

Volume Button

3 - 8

Installing a Memory Card

1. Press the Power key to put the terminal in suspend mode; see Suspend Mode on page 2-11.

2. Remove the battery door and the battery.

3. Place the terminal on a flat, secure surface with the keyboard face down.

4. Unlock the access door to the microSD or microSDHC socket.

5. Lift the door up to expose the socket.

6. Insert the microSD or microSDHC card into the socket.

NEW

IMAGE

REQUIRED

NEW

IMAGE

REQUIRED

7. Close and lock the access door.

8. Install the battery and the battery door.

Installing a SIM Card

See To Install a SIM Card on page 8-2.

3 - 9

Bottom Panel: 9700

1 2 3 4 5 6 7 8 9 10 11

Description

GND MIC_IN RI USB_DUSB_D+ NO CONNECT USB_5V_IN 5V_OUT TXD RXD RTS

CTS

DTR

DSR 15 16

MONO SPEAKER

VDC_IN

Note: Signals referenced are for a DTE device.

I/O Connector

The I/O connector powers the terminal, charges the main battery, and facilitates communication. All Dolphin peripherals are designed to work exclusively with this connector.

The I/O connector supports RS232 and USB communication. For RS232, the maximum communication speed is 115.2 Kbps with seven baud rate settings. For USB, the communication speed is up to 12 Mbps.

Powering Out

The I/O connector also provides power out (to peripheral devices) +5V at 500mA. This means that, with the proper cable, the terminal can power another device. By default, power out is disabled. To enable power out, alter the registry as follows:

[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\Serial4]

Conn5Venable=1

3 - 10

Using the Touch Panel

Honeywell defines proper use of the terminal touch panel as using a screen protector and proper stylus. Screen protectors maintain the ongoing integrity (i.e., prevent scratching) of the touch panel, which is why their use is recommended for applications that require a high to medium level of interface with the touch panel, such as signature capture for proof of delivery.

Honeywell advocates the use of screen protectors on all Dolphin devices. We recommend implementing a screen protector replacement program to ensure that screen protectors are replaced periodically when signs of damage/wear are noticeable. For general use, we recommend replacing the screen protector every thirty (30) days. However, replacement cycles vary according to the average level of touch panel use in your application.

Replacement screen protectors can be purchased directly from Honeywell. Please contact a Honeywell sales associate for details.

Honeywell also mandates use of a proper stylus, which is one that has a stylus tip radius of no less than

0.8mm. Use of the Honeywell stylus included with the terminal is recommended at all times. Honeywell warranty policy covers wear on the touch panel for the first 12 months provided that a screen

protector is applied and an approved stylus is used for the 12 month duration covered by the warranty.

Installing a Screen Protector

Dolphin terminals ship with a screen protector already installed. You will need to replace the screen protector at regular intervals.

1. After the current screen protector has been removed from the touch panel, clean the touch panel thoroughly with a clean, non-abrasive, lint-free cloth. Make sure nothing else is still attached to the touch panel.

2. Align the exposed section of the protector with the bottom edge of the touch panel. Make sure that the screen protector is flush with each side of the touch panel. To reposition, lift up gently and reapply.

3. Press the screen protector firmly and carefully across the surface of the touch panel as you peel away the backing.

4. If necessary, smooth out any air pockets or bumps.

3 - 11

Healthcare Housing

Some configurations of the 9700 terminal are available with an external plastic that is designed to resist the effects of harsh prevent chemicals from seeping through the housing.

Important! The following cleaning solutions have been tested to assure safe cleaning of your terminal’s

disinfectant-ready housing. They are the only solutions approved for use with these terminals. Damage caused by the use of cleaners other than those listed below may not be covered by the warranty.

• Sani-Cloth® HB wipes

• Sani-Cloth® Plus wipes

• Super Sani-Cloth® wipes

• Isopropyl Alcohol wipes (70%)

• CaviWipes

• Virex® 256

• 409® Glass and Surface Cleaner

• Windex® Blue

• Clorox® Bleach – 100%

• Gentle dish soap and water

™

chemicals

in a healthcare

environment.

The plastic is crystalline in nature, which helps

3 - 12

Batteries

There are two types of battery power: the main battery pack installed in the back panel and the backup battery located inside the terminal. They are designed to work together to prevent data loss when the terminal is in use over long periods.

Both batteries must be completely charged before using a Dolphin terminal for the first time!

Main Battery Pack

We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in

damage not covered by the warranty.

The 7.4V, 12.0 watt hour Li-ion battery pack is the primary power source for the terminal. The Li-ion battery is designed to operate in a temperature range of -10° to 50°C (14° to 122°F).

Charging Options

When the Li-ion battery is installed in the terminal, use one of the following peripherals:

• Dolphin 9700 HomeBase Device (see page 11-1)

• Dolphin 9700 Mobile Base Device (see page 12-1)

• Dolphin 9700 ChargeBase Device (see page 13-1)

• Dolphin 9700 Net Base (Please see the Dolphin Net Base Quick Start Guide on

www.honeywellaidc.com.)

• Dolphin 9700 Mobile Charger

When the Li-ion battery is not installed in the terminal:

• Place the battery pack in the Dolphin 9700 QuadCharger device (see page 14-4)

• Place the battery pack in the Auxiliary Battery Well of the Dolphin 9700 HomeBase device (see page

11-6).

Charging Time

The Li-ion battery pack requires 4 hours to charge completely before initial use.

Storing Batteries

To maintain optimal battery performance, follow these storage guidelines:

• Avoid storing batteries outside the specified range of -4° to 104° F (-20° to 40°C) or in extremely high

humidity.

• For prolonged storage, do not keep batteries stored in a charger that is connected to a power source.

Guidelines for Battery Pack Use and Disposal

The following are general guidelines for the safe use and disposal of batteries:

• We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may pose a

personal hazard to the user.

• Replace defective batteries immediately; using a defective battery could damage the Dolphin terminal.

• Never throw a used battery in the trash. It contains heavy metals and should be recycled according to

local guidelines.

• Don’t use a battery in any other manner outside its intended use in Dolphin terminals and peripherals.

• Don’t short-circuit a battery or throw it into a fire; it can explode and cause severe personal injury.

3 - 13

• Excessive

discharge damages

a battery.

Recharge

the battery when your terminal indicates low battery

power.

• If you observe that the Honeywell battery supplied is physically damaged, please send it to Honeywell

International Inc. or an authorized service center for inspection. Refer to the Product Service and Repair section of this guide.

• Although your battery can be recharged many times, it will eventually be depleted. Replace it after the

battery is unable to hold an adequate charge.

• If you are not sure the battery or charger is working properly, please send it to Honeywell International

or an authorized service center for inspection.

Internal Backup Battery

Located inside the terminal, the backup battery is a 3.6 Volt nickel metal hydride (NiMH) battery. The internal backup battery prevents the terminal from being reset if you need to remove and replace the

main battery pack. It retains RAM data and allows the real-time clock to remain operational for up to 30 minutes when the main battery pack is removed. If the terminal is left without the main battery pack for more than 30 minutes, the internal backup battery needs to be recharged to function according to its specifications.

Note: Data and programs stored in Flash memory are not lost even if the internal backup battery fails. However, you

must reset the real-time clock; see Set the Time and Date on page 2-2.

Charging

The internal backup battery is powered by the main battery pack. Therefore, charging the internal backup battery requires that the main battery pack be installed in the terminal and the terminal be connected to a charging device.

The internal backup battery must be fully charged before using the terminal for the first time. The initial charge cycle takes approximately 8 hours. After that, if the internal backup battery becomes fully discharged of power, it requires a minimum of 10 hours of charging time to function normally.

Guidelines for Use

Follow these guidelines to maximize the life of the internal backup battery:

• Keep a charged Li-ion battery pack in the terminal; the backup battery prematurely discharges if there

is not at least a partially charged battery in the terminal.

• Keep the terminal connected to power when the terminal is not in use.

Managing Battery Power

Data and files saved on Dolphin terminals may be stored in RAM memory, which does not persist through a hard reset. Therefore, to help prevent data loss, maintain a continuous power supply to the terminal.

Letting the backup battery become fully discharged causes the terminal to lose all data in RAM. Therefore, you should keep a charged battery pack in the terminal at all times. The internal battery discharges

prematurely if there is not at least a partially charged battery in the terminal. When you remove

a battery pack, insert another charged battery pack in the terminal immediately.

Default Critical and Low Battery Points

When the terminal is running on battery power (as opposed to external power), warnings are displayed when the battery reaches critical and low battery points. The warning points are determined by the following registry entry:

[HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Power]

3 - 14

There are two DWORD values in this registry entry: LowBatt and CriticalBatt. The default values for these entries are as follows:

LowBatt=19 (25%)

This sets the Low Battery point to 25% (19 hex=25 decimal). When the battery hits the percentage charge specified here, the user is notified by this icon in the Navigation bar . If the main battery is low and the terminal is in Suspend Mode, pressing the SCAN or Power

button won’t wake the Dolphin terminal; you must replace the

discharged

battery with a battery

charged over the 25% mark before you can resume terminal operation.

CriticalBatt=a (10%)

This sets the Critical Battery point to 10% (a hex= 0 decimal). When the battery hits the percentage charge specified here, the user is notified by this icon in the Navigation bar .

Note: Warnings do not appear when the terminal is on external power.

Setting Critical and Low Battery Points

Developers can reset these parameters in the registry from 0 (no warning) to 99 (would nearly always warn). You can review and set these battery points in the RegEdit Power Tool.

1. Tap Start > Power Tools > RegEdit.

2. Drill down to HKEY_LOCAL_MACHINE > System > CurrentControlSet > Control > Power.

3. Tap the Value Name to change the Value Data. You can reset the Value Data from 0 (no warning) to 99 (would nearly always warn).

4. Tap OK to save changes.

For more information about the RegEdit Power Tool, refer to the Dolphin Power Tools User’s Guide available for download at www.honeywellaidc.com.

Checking Battery Power

Tap Start > Settings > System > Power.

For more information, see Power on page 6-13.

3 - 15

Resetting the Terminal

There are two types of system resets: a soft and a hard reset.

Soft Reset (Warm Boot)

A soft reset re-boots the device without losing RAM data. You would perform a soft reset when

• the terminal fails to respond.

• after installing some software applications.

• after making changes to certain system settings, such as network cards.

1. Press and hold the RED + TAB

TAB

keys for approximately 5 seconds.

2. The decode and scan LEDs flash for approximately three seconds as the terminal resets.

3. When the reset is complete, the Today screen displays.

Hard Reset (Cold Boot)

A hard reset resets the operating system, restores the terminal back to factory defaults, and resets the terminal after a bootloader, keyboard, and kernel upgrade.

A hard reset erases all of the data stored in RAM memory and all RAM installed applications!

1. Press and hold the RED + ENT keys for approximately 5 seconds.

2. The decode and scan LEDs light for approximately 3 seconds.

3. The terminal re-initializes; see Initialize the Mobile Computer on page 2-8.

ENT

Suspend Mode

The terminal goes into Suspend Mode automatically when the terminal is inactive for a programmed period of time. You can program this time on the Advance tab of the Power System Setting; see Power on page 6-13.

To put the terminal into suspend mode manually, press the Power key and the screen goes blank.

To wake the terminal from suspend mode, press the Power key or SCAN keys

SCAN

Hardware Maintenance

When needed, clean the image engine window and the LCD display with a clean, non-abrasive, lint-free cloth. The terminal can be cleaned with a damp cloth.

For additional information on hardware maintenance specific to the Dolphin Healthcare Housings, see

page 3-12.

3 - 16

Using the Scan Image

Engine

Overview

The Dolphin terminal houses a compact image engine that instantly reads popular 1D and 2D bar codes and supports omni-directional aiming and decoding for greater flexibility in real-world settings. The image engine can also capture digital images, such as signatures and pictures of damaged inventory.

With the latest CMOS-based technology, the engine works like a digital camera and enables digital image capture, signature capture, and reading of OCR characters.

Angled Imaging

All imager are installed at a 33 degree downward-facing angle for enhanced comfort and maneuverability while scanning.

Image Engine Specifications

Engines

5100SR/SF

5300SR

5100 Standard Range (5100SR) 5300 Standard Range (5300SR)

1D 2D Image

8.3 mil Linear

Capture Aiming Pattern

10 mil PDF417

5100 Green Aiming Beam (page 4-4)

5300 Red High-Vis Aiming Pattern (page 4-4)

13 mil UPC

15 mil Data Matrix

Omni-Directional Aiming

15 mil QR

35 mil MaxiCode

Working Range:

Near

Far

3.5 in. (8.9 cm)

7.6 in. (19.3 cm)

5100 Smart Focus (5100SF)

Working Range:

Near

Far

6.6 mil PDF417

2.7 in. (6.8 cm)

5.9 in. (14.9 cm)

(.020 cm)

(.017 cm)

(.025 cm)

3.1 in. (7.9 cm)

9 in. (22.9 cm)

7.5 mil Linear

(.019 cm)

2.4 in. (6.1 cm)

6.4 in. (16.2 cm)

(.033 cm)

2.1 in. (5.3 cm)

13.2 in. (33.5 cm)

10 mil Linear

(.025 cm)

2.1 in. (5.3 cm)

7.5 in. (19 cm)

(.038 cm)

2.3 in.

5.8 cm)

10.2 in. (25.9 cm)

10 mil PDF417

(.025 cm)

2.1 in. (5.3 cm)

7.5 in. (19 cm)

(.038 cm)

3.1 in. (7.9 cm)

8.8 in. (22.4 cm)

13 mil UPC

(.033 cm)

1.9 in. (4.8 cm)

8.8 in. (22.3 cm)

(.089 cm)

2.0 in. (5.1 cm)

13.0 in. (33 cm)

15 mil Data Matrix

(.038 cm)

1.7 in. (4.3 cm)

7.4 in. (18.8 cm)

4 - 1

Laser Specifications

The maximum power outputs for each diode are as follows:

• Illumination LED: 194.0 uW

• Aimer laser (5300 engine): 360.1 uW

• Aimer LED (5100 engine): 81.6 uW

Supported Bar Code Symbologies

Symbology Type

Symbology Name

1D Symbologies

2D Symbologies

Composite Codes

OCR

Codabar ISBT 128 Code 3 of 9 Matrix 2 of 5 Code 11 MSI Code 32 Pharmaceutical (PARAF) Plessey Code 93 PosiCode Code 128 Straight 2 of 5 IATA EAN with Add-On Straight 2 of 5 Industrial EAN with Extended Coupon Code Telepen EAN-8 Trioptic Code EAN-13 UPC GS1-128 UPC-A GS1 Databar UPC-E Interleaved 2 or 5

Aztec GS1 Databar Codablock MaxiCode Code 16K Micro PDF Code 49 OCR Composite PDF417 Data Matrix QR Code

Aztec Mesa Codablock F EAN·UCC GS1 Databar-14

OCR US Money Font MICR (E 13 B) and SEMI Font OCR-A OCR-B

Postal Codes

4 - 2

Postnet and most international 4-state codes Australian Post British Post Canadian Post China Post Japanese Post KIX (Netherlands) Post Korea Post Planet Code

Decoding

The terminal supports two types of image decoding for use in various bar code reading and imaging applications: full-area imaging and Advanced Linear Decoding (ALD).

Full-Area Imaging Full-area imaging provides omni-directional reading of linear and non-linear 1D and 2D bar codes, OCR,

signature capture, and picture taking. When reading all bar code types using full-area imaging, a positive read can be obtained from many positions; see Aiming Options on page 4-4. To achieve the best read, the aiming beam should be centered horizontally across the bar code.

ALD ALD provides fast reading of linear and stacked linear bar codes. To achieve a positive read when reading

linear 1D and PDF417 bar codes, the green aiming beam should be centered horizontally across the bar code. When ALD is enabled, the reader does not read matrix or postal codes.

To Decode a Bar Code

The imager faces straight out the top panel. The aiming beam should be oriented in line with the bar code to achieve optimal decoding. A range of 4-10 inches (10-25 cm) from the bar code is recommended.

1. Point the Dolphin terminal directly at the bar code.

2. Project the aiming beam or pattern by pressing and holding the SCAN key.

3. The scan LED lights red.

4. Center the aiming beam over the bar code; see Aiming Options on page 4-4.

5. When the bar code is successfully decoded, the decode LED lights green and the terminal beeps.

6. The bar code information is entered into the application in use.

4 - 3

Aiming Options

The aiming beams are smaller when the terminal is held closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit whereas symbologies with larger bars or elements (mil size) should be read farther from the unit.

5100 Green Aiming Beam

Linear Bar Code

2D Matrix Symbol

5300 Red High-Vis Aiming Pattern

If your Dolphin terminal is configured with a 5300 imager, high-vis aimers frame the bar code for more intuitive aiming.

4 - 4

Capturing Images

The image-capture process is an intuitive, split-second operation for experienced users. By following the basic guidelines, new users can easily develop their own technique and, with practice, quickly learn to adapt it to different application environments.

Image Preview When the imaging process is initiated, the touch screen displays a preview of the object. This is a live

video image of what the imager is currently viewing. The live video image has a slightly degraded appearance compared to the captured image. This is normal.

Scan Key On all 9700 terminals, the SCAN key captures images.

File Formats File formats supported for image storage include Bitmap (BMP), JPEG (JPG) and Portable Network

Graphics (PNG). The default file format for images is a grayscale JPG. Compression

Digital images have a maximum image size of 640 x 480 pixels and may have up to a 256 grayscale image definition.

The image quality and related file size are determined by the data compression method used by the software application used to take images. The average size of the image file is approximately 4–8K. However, the size of the image depends on the content of the image - the more complex the content, the larger the file size. For the highest quality image, take grayscale images.

Taking an Image

The following steps are basic guidelines for taking images:

1. Point the Dolphin terminal directly at the object. The imager points straight out the top panel.

2. To preview the image, press and hold the SCAN key.

3. The touch screen displays a preview of the object, and the decode and scan LEDs light red.

4. Adjust the terminal’s position until the object appears on the screen the way you want it to appear in the image.

5. Hold the terminal still and release the SCAN key. The scan and decode LEDs flash red, the screen flashes, and the captured image appears on the screen.

6. Unless otherwise specified by the application in use, the image is saved to the \My Device\My Documents folder (Start > Programs > File Explorer > My Device > My Documents).

4 - 5

Enabling the Aimer

If your Dolphin terminal is configured with the 5300 imager, you can enable the aiming pattern for imaging in the Imaging Demo. For details about the aimer, see 5300 Red High-Vis Aiming Pattern on page 4-4.

1. Tap Start > Demos > Imaging Demo > Setup menu > Aimer.

2. The aiming pattern is now enabled for imaging.

Uploading Images

Image files can be uploaded to a host workstation via Microsoft ActiveSync and a Dolphin communication peripheral or your wireless radio connection.

4 - 6

Using the

Keyboards

Available Keyboards

There are two keyboard options in the 9700 series:

ESC

All Keyboards Contain the Following:

• Backlit for easy viewing in various lighting conditions.

• Centrally-located keys for both right- and left-hand operation.

• Color-coding so you can clearly see the most common keyboard combinations.

• Function, navigation, and modifier keys.

Keyboard Combinations

See 31-Key Keyboard Combinations on page 5-5. See 45-Key Keyboard Combinations on page 5-8.

Common Buttons

See Using the Function Keys on page 5-2. See Using the Modifier Keys on page 5-3. See Using the Navigation Keys on page 5-3.

31-Key Numeric Keyboard 45-Key QWERTY Keyboard

SCAN

VOL

TAB

@?!

4 7

GHI

PQRS

2 5 8

ABC

JKL

TUV

F10

3 6

MNO

WXYZ

DEF

ENT

ALT

TAB

R T Y U

8 9

SCAN

VOL

F G H

SPACE

;

# /

(

)

M ,

ESC

ENT

F10

“

5 - 1

Using the Function Keys

Name

Key

Function

Backlight

Backspace

Enter (ENT)

Escape (ESC)

Power Key

Numeric Keyboard

Blue

QWERTY Keyboard

ENT

ESC

Numeric Keyboard

Blue

QWERTY Keyboard

ESC

Turns the keyboard backlight on and off.

Moves the cursor back one space each time the key is pressed. If you are typing text, it deletes the previous character each time it is pressed.

Confirms data entry.

Cancels the current action.

Puts the terminal in and wakes the terminal from Suspend Mode; see

Suspend Mode on page 3-16.

SCAN Key

Space (SP)

Tab

5 - 2

Numeric

Blue

QWERTY Keyboard

Numeric Keyboard

SPACE

QWERTY Keyboard

TAB

SCAN

Keyboard

SCAN

Activates the scan and “wakes” the terminals from Sleep Mode. Its position allows convenient one-handed image-taking and/or bar code decoding.

Turns the flashlight on and off. The flashlight is located on the back panel of the terminal.

Moves the cursor one space.

Moves the cursor to the next tab stop or the next control (on a form).

Using the Modifier Keys

Name

Key

Function

Shift

The shift key modifies only the next key pressed; it must be pressed before each key you wish to modify. Shift toggles the keyboard between uppercase alphabet mode and lowercase alphabet mode.

Double-tap shift to toggle Caps Lock on and off. When Caps Lock is toggled on, characters are uppercase; when toggled off, characters are

Blue and Red

lowercase.

Blue

Red

The blue and red keys are used in combination with other keys to type special characters and perform system functions. Each key modifies only the next key pressed.

Each keyboard is color-coded to indicate the character typed or function performed when specific keys are pressed immediately after the blue or red modifier key.

Using the Navigation Keys

Located in the center of each keyboard for easy access with either hand, the navigation keys navigate the cursor through application screens.

Key

VOL

Blue

Note: Additional functionality varies according to the application in use.

Function

Moves the cursor up one row or line. OR Moves the cursor down one row or line.

Moves the cursor up one page. OR Moves the cursor down one page.

Red

Raises the volume. OR

Lowers the volume.

Moves the cursor one character to the right.

Moves the cursor one character to the left.

5 - 3

31-Key Numeric Keyboard

Left Soft

Send

key

Backlight

key

Escape

Shift

key key

Tab

key

ENT

Navigation keys

Right Soft key

Enter key

ALT

End key ALT key

Space key Backspace key

SCAN

key

TAB

Blue

PQRS

key

Red key

ESC

@?!

GHI

SCAN

VOL

ABC

JKL

TUV

F10

DEF

MNO

WXYZ

5 - 4

31-Key Keyboard Combinations

Key Power Scan

Normal

Scan

Shift

Scan

Blue

Light

Off/On

Shift-Blue

Light

Red

Scan

Left Soft

Right Soft

Left Up Down Right Send

TAB Enter End

Backlight ESC SHIFT

Perform Left Function

Perform Right Function

Left Up Down Right Send (phone

calls) Tab Return End (phone

call)

Escape Shift

Left Up Down Right Send (phone

calls) Tab Return End (phone call) End (phone call) End (phone call) End (phone call)

Perform Left Function

Perform Right Function

Left Volume Up Volume Down Right Send (phone

calls) LWIN Return

Left Volume Up Volume Down Right Send (phone

calls) LWIN Return

Left Prior Next Right Send (phone calls)

Tab Return

Toggles Keyboard Backlight On/Off

Escape

Escape Shift

Escape

1 2 3 4 5 6 7 8 9 0 ALT Space

1 2 3 4 5 6 7 8 9 0 Menu Space

! @ # $ % ^ & * ( ) Menu Space

@,?,! a,b,c d,e,f g,h,i j,k,l m,n,o p,q,r,s t,u,v w,x,y,z & Menu Space

@,?,! A,B,C D,E,F G,H,I J,K,L M,N,O P,Q,R,S T,U,V W,X,Y,Z ) Menu Space

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Menu Space

5 - 5

Key BKSP

Normal

Backspace

Shift

Backspace

Blue

Backspace

Shift-Blue

Backspace

Red

Backspace

Blue Period Comma Red

Blue . (period) , (comma) Red

> <

Blue * (multiply) #

* (multiply) #

. (period) , (comma) Red

5 - 6

45-Key QWERTY Keyboard

Left Soft key

Tab

key

Send

key

Shift

VOL

; :

# /

key

(

Navigation

keys

Right Soft key

Enter key

ENT

)

ESC

“

F10

End key

Backspace key

Red key

SCAN

TAB

R T Y U

F G H

8 9

SPACE

Space key, Blue key, Escape key

5 - 7

-Key Keyboard Combinations

Key Power Scan

Normal

Scan

Shift

Scan

Blue

OFF/ON

Light

Red

Scan

Left Soft

Right Soft

Left Up Down Right Send

TAB Enter End

ESC SHIFT A

Perform Left Function

Perform Right Function

Left Up Down Right Send (phone

calls) Tab Return End (phone

call) Escape Shift a

Left Up Down Right Send (phone

calls) Tab Return End (phone call) End (phone call) End (phone call)

Perform Left Function

Perform Right Function

Left Volume Up Volume Down Right Send (phone

calls) LWIN Return

Left Prior Next Right Send (phone calls)

Tab Return

Escape

backlight

Escape

F11

5 - 8

B C D E F G H I J K L M

b c d e f g h i j k l m

B C D E F G H I J K L M

# 8 5 2 6 ; :

- (subtract) “ ? & \

F24 F22 F13 F3 F14 F15 F16 F8 F17 F18 F19 F26

Key N O P Q R S T U V W X Y Z

Normal

n o p q r s t u v w x y z

Shift N O P Q R S T U V W X Y Z

Blue

/ + (add) = ! 3 4 $ ) 9 1 7 ( * (multiply)

Red

F25 F9 F10 F1 F4 F12 F5 F7 F23 F2 F21 F6 F20

Space BKSP Blue Period Comma Red

Space Backspace Blue . (period) , (comma) Red

Space Backspace Blue-Lock > <

Space Backspace

0 _ (underscore) F27

Space Backspace

. (period)

5 - 9

5 - 10

System

Settings

Overview

Customized settings are available on the Start menu. Tap Start > Settings and settings screen opens.

Icon

Bluetooth

Clock & Alarms

Lock

Sounds & Notifications

Today

Connections

Personal

System

Description

Configures the Bluetooth radio. This icon appears only if a Bluetooth radio and driver are installed on the terminal.

Set the system clock, date, time and schedule alarms.

Password protect the terminal to limit access to the terminal Set the sound volume, enables and disables sounds for specific actions, and sets sound

parameters for system notifications.

Customize the look and the information displayed on the Today screen. Establishes network connections settings.

Customizes buttons, set SIP options, and adjust headset settings.

Adjusts system settings.

See Page

See Working with the Bluetooth

Radio on page 9-1.

See Clock & Alarms on page 6-2.

See Connections Menu on page 7-

See Personal Menu on page 6-3.

See System Menu on page 6-7.

Microsoft My Phone

Synchronizes your phone’s contacts, calendar, tasks, text messages, music, photos, videos, and other documents with your My Phone account at http:\\myphone.microsoft.com.

6 - 1

Clock & Alarms

The Clock & Alarms settings can be accessed from the Today screen or the Settings Menu.

1. On the Today screen, tap the line that displays the time and date or go to Start > Settings > Clock & Alarms,

Windows Mobile 6.5, Professional Windows Mobile 6.5, Classic

2. The Clock Settings screen appears. This setting sets the system clock. All scheduled items run according to this setting.

Note: To keep the system clock accurate, the time and date need to be reset after every hard reset of the

terminal.

The time zone defaults to GMT-5 Eastern US; tap the arrow to the right of GMT-5 Eastern US to select another time zone. Set the correct time and date in the remaining fields and tap OK to save.

6 - 2

Personal Menu

To access the Personal Menu, go to Start > Settings > Personal. The screen opens displaying the Personal Menu.

Icon

Buttons

Input

Owner Information

Phone

Description

Program the side buttons to perform specific tasks.

Customizes the SIP (soft input panel). Enter your contact information.

This information will appear on the Today screen. When the GSM radio is enabled, tap this icon

to set up user parameters.

See Page

See Buttons on page 6-4.

See Input on page 6-5.

See Setup Options on page 8-7.

Note: Personal settings are stored in RAM memory. They are replaced by system defaults after each hard reset.

For more information about resets, see Resetting the Terminal on page 3-16.

6 - 3

Buttons

The Buttons setting programs certain keyboard buttons to launch applications or execute commands.

Enable HotKeys

Default Buttons setting assignments are inactive until you enable the HotKeys Power Tool.

Tap Start > Power Tools and tap the HotKeys icon once. HotKeys is enabled, and the button assignments in the Buttons setting are active.

For more information about the HotKeys Power Tool, refer to the Dolphin Power Tools User’s Guide, which is available for download from the web at www.honeywellaidc.com.

Changing Button Assignments

1. After HotKeys is enabled, tap Start > Settings > Personal > Buttons .

Note: The buttons that appear on this window are the only buttons that can be programmed via the Buttons setting.

You cannot add buttons to this window.

2. To change button assignment, tap on the name of the application in the Assignment column and select a program or command in the Assign a program drop down list.

3. Tap OK to save.

4. Press the button to verify that the program is launched or action performed.

Available Applications

The Assign a program list contains the applications installed on the terminal. If there is a program installed that you would like to see in this list, paste a Shortcut to the program in the \\Windows\Start Menu\Programs folder. For instructions about creating shortcuts, see Using File Explorer on page 6-5.

6 - 4

Additional Functions

The Assign a program list also contains the following commands:

Command Description <Input Panel> Opens the soft input panel. <None> Nothing happens when the button is pressed. <OK/Close> Performs the same function as tapping OK on the screen. <Scroll Down> Scrolls down in the open application. <Scroll Left> Scrolls left in the open application. <Scroll Right> Scrolls right in the open application. <Scroll Up> Scrolls up in the open application. <Start Menu> Opens the Start menu. <Today> Opens the Today screen.

Input

The Input settings enables you to customize input from the SIP, and adjust word completion settings in Microsoft applications.

Input Method

Word Completion

Options

Using File Explorer

If you do not see the program listed, you can either use File Explorer to move the program or ActiveSync on the workstation to create a shortcut to the program and place the shortcut in the Start Menu folder.

Note: We recommend that you Copy and Paste Shortcut so that you do not alter your program configurations by

accident. Using Copy and Paste Shortcut (as opposed to Cut and Paste) ensures that the program files remain where they need to be for the system to find them to perform system functions.

6 - 5

1. Tap Start > File Explorer , and navigate to the program (My Device > Program Files).

2. Tap and hold on the program, then tap Copy on the pop-up menu.

3. Navigate to the Windows folder and open the Start Menu (My Device > Windows > Start Menu), tap and hold a blank area of the window, and tap Paste Shortcut on the pop-up menu.

4. Tap the Start menu to verify that the program now appears on it.

Using ActiveSync on the Workstation

Here, you are performing the same basic process as on the terminal, except that you are using the Explore utility (Windows Explorer) to copy and paste the shortcut.

1. Open ActiveSync > Explore and navigate to the program.

2. Right-click on the program and select Create Shortcut.

3. Select the shortcut, right-click, and select Cut.

4. Navigate to the Start Menu folder (Windows > Start Menu).

5. Right-click on an empty area and select Paste Shortcut.

6. On the terminal, tap the Start menu.

7. Verify that program appears.

6 - 6

System Menu

The System menu enables you to verify and sometimes alter system parameters. To access the System menu, go to Start > Settings > System . Tap the appropriate icon to open that system setting.

Icon About Backlight Certificates Encryption Error Reporting External GPS Managed Programs Memory Power RIL Regional Settings Remove Programs

See Page

See About on page 6-8. See Backlight on page 6-8. See Certificates on page 6-9. See Encryption on page 6-9. See Error Reporting on page 6-9. See External GPS on page 6-10. See Managed Programs on page 6-10. See Memory on page 6-11. See Power on page 6-13. See RIL on page 6-12. See Regional Settings on page 6-13. See Remove Programs on page 6-13.

Screen Task Manager

See Screen on page 6-15. See Task Manager on page 6-16.

6 - 7

About

The About system setting displays specific information about the terminal. It contains three tabs:

Version Tab Displays the information about the software, operating system, and processor. Device ID Tab Displays the information the terminal uses to identify itself to other devices. It can be important to

Copyrights Tab Displays important copyright information.

know this information if the Dolphin terminal is going to be part of a networked system of devices.

Device name: Displays the system’s default name. (This is the name used by ActiveSync.) Description: Displays the description of the device ID.

Backlight

The Backlight system setting enables you to customize backlight functionality for the display. The backlight for the color display is user-defined. Tap Start > Settings > System > Backlight.

There are two tabs: The Battery tab determines the backlight timeout when the terminal is running on battery power. The External tab determines the backlight timeout when the terminal is running on external power.

The options on each tab are the same.

Turn off backlight: Select how many minutes you want to elapse before the backlight automatically turns off. Turn on backlight: Select this option if you want the backlight to turn on when the button is pressed or the touch

screen is tapped.

Backlight Intensity

Tap the Backlight tab and move the slider to set the intensity of the backlight. The default is 8.

6 - 8

Certificates

Certificates shows you the certificates that are recognized by the operating system.

Encryption

Encryption gives you the option of encrypting files placed on storage cards to that those files cannot be read by any other device.

Error Reporting

Error Reporting gives you the option of enabling or disabling the error reporting function of Windows Mobile 6.5.

6 - 9

External GPS

External GPS determines which port a third-party GPS software application can use to access the GPS receiver.

Note: You need the installation parameters from the GPS manufacturer to configure the connection.

Managed Programs

Managed Programs .

6 - 10

Memory

The Memory system setting displays capacity and usage statistics for both RAM (volatile) and IPSM/ Storage Card (non-volatile) memory. Access this setting whenever you receive system messages about memory.

You cannot change the terminal’s memory allocation in the Memory system setting. To change the memory allocation, you need to use the SetRAM Power Tool (Start > Power Tools > SetRAM). For more details, please refer to the Honeywell Power Tools User’s Guide, which is available for download from

www.honeywellaidc.com.

There are three tabs: Main, Storage Card, and Running Programs.

Main Tab

Storage Card Tab

This tab displays the usage statistics of the on-board, volatile RAM memory.

Columns:

Storage=RAM memory used Program=RAM memory used to run programs.

store programs and program

data.

Rows:

Total=Displays the current MB of memory allocated for use. In

use

=Displays the total MB

Free=Displays the total MB of memory available.

that allocated memory being

used.

This tab displays the current capacity and usage statistics of the selected memory type: IPSM or Storage Card.

Select the memory type from the drop-down list. IPSM is selected by default.

Total storage card memory= The total MB of memory capacity of IPSM or Storage Card.

In use=The MB currently being used. Free=The MB that is still available for use.

IPSM—Short for Internal Persistent Storage Manager, this is the on-board Flash

memory that is non-volatile. Because this memory is non-volatile, data or programs stored in IPSM are not affected when power is removed. Autoinstall programs, for example, are stored in IPSM so that they are always installed at cold-boot startup.

Storage Card—You can install one memory card in Dolphin terminals (see Installing

a Memory Card on page 3-9). If a storage card is installed in the terminal, you can

select it in the drop-down list and see capacity and usage statistics for the card.

6 - 11

RIL

The RIL Information screen displays useful statistics for the radio.

To verify whether or not the GSM radio is enabled, check the Dolphin Wireless Manager (see page 7-6).

6 - 12

Power

Power system settings contains two tabs: Battery and Advanced.

Battery Tab

Advanced Tab

Note: You can also set automatic turn-off times for the terminal to conserve power. When the terminal is “turned

off,” that means that it goes into suspend mode; see Suspend Mode on page 3-16.

For more information, see Batteries on page 3-13.

Determines power time-outs. For On battery power, select from the drop-down list,

the number of minutes of inactivity you want to pass before the terminal powers off when running on battery power.

For On external power, select from the drop-down list, the number of minutes of inactivity you want to pass before the terminal powers off when running on external power.

Regional Settings

Regional Settings enables you to customize the appearance and formatting to your geographic region. Specifically, you can customize

numbers

(i.e., number of decimal places allowed), currency (i.e.,using the $ or € symbol), time, and date. These specifications apply to all screens, including the Today screen. The Region tab displays an overview of the region selected in the drop-down list at the top.

The terminal is loaded with a number of pre-programmed regional settings. Select one from the list and the results appear on the screen. To see specific settings or to change a specific setting, tap on one of the tabs, make the change and tap OK to save it.

Remove Programs

Remove Programs enables you to remove programs installed on the terminal. Use this setting to troubleshoot when you receive messages that the terminal is out of memory. The programs removed are removed from RAM memory. Any program (usually CAB or DLL files) stored in the Autoinstall folder (My Device > IPSM > Autoinstall) will re-install after the next hard reset.

For information about the hard reset process, see Hard Reset (Cold Boot) on page 3-16.

6 - 13

1. Tap Remove Programs. In the list, select the program you want to remove.

2. Tap Remove. The following message appears:

3. Tap Yes. Wait while the program is removed.

4. Verify that the program no longer appears in the list.

6 - 14

Screen

The Screen system setting contains three tabs: General, Clear Type, and Text Size.

General Tab

ClearType Tab

Text Size Tab

Orientation

The General Tab enable you to set the dynamic screeen rotation. Three choices of screen orientation are supported: Portrait, Landscape (right-handed), and Landscape (lefthanded).

Align Screen The General Tab also allows you to re-align the screen.

You need to re-align the screen if tapping buttons or icons with the stylus no longer seems to work appropriately.

Tapping Align Screen brings up the align screen window where you are guided to tap a target several times. This recalibrates how the touch screen receives input.

• Alignment should always be performed with a stylus designed for touch panel applications. The small point is required for accurate calibration.

• Press the stylus firmly into the center of the cross-hair target once and release. Do not “double-tap” the target.

The display supports ClearType font rendering, which is a Microsoft technology that dramatically increases the readability of text on LCD displays.

To enable ClearType font rendering, select Enable ClearType and tap OK.

For more information about ClearType font rendering, visit: www.microsoft.com/typography/cleartype/ what.htm?fname=%20&fsize=

The Text Size tab enables you to perform font scaling within certain views of the

• Today screen,

• Contacts,

• Calendar,

• Messaging, and

• Tasks.

Font scaling means that you can increase or decrease the point size of the font on application windows.

To change the font size, move the slider toward Smallest or Largest. The Example text changes to reflect the font change. Tap OK to save the new font size setting.

6 - 15

Task Manager

The Task Manager provides information about applications and processes running on your mobile computer. You can use the Task Manager to monitor the memory and CPU usage of specifc applications and processes. Check the Task Manager when you are receiving out of memory errors or when the mobile computer is running slowly.

Using the Task Manager

Applications To view the status of the programs running on your

Note: Anytime you stop a running program, it frees up RAM memory. Be advised that, when you stop a

program here, any unsaved data in that program is lost. To free up memory without risking data loss, return to the running program, save your data, and close the application.

Processes To view information about the processes running on the

mobile computer, tap the Menu button at the bottom of the screen, then tap View > Applications.

From the application list you can:

• Tap and hold on an the pop-up

• Tap and hold on an application, then tap End Task or End All Tasks on the pop-up menu.

mobile computer, tap the Menu button at the bottom of the screen, then tap View > Processes.

menu.

application,

then tap

Switch

To on

6 - 16

Communication

Connections Menu

The Connections system setting provides access to the terminal’s various wireless communication options.

Icon

Note: All server-assigned IP addresses use Dynamic Host Configuration Protocol (DHCP).

Setting

Beam

Connections

Dolphin Wireless Manager

USB to PC

Wi-Fi

Tapping this icon…

Enables infrared communication.

Opens Microsoft’s connections manager.

Manages the wireless radios installed in the terminal.

Enables advanced USB communication via ActiveSync, which is wired communication.

Enables you to configure Wireless Zero Config (WZC). This icon appears only if the 802.11a/b/g driver is loaded on the terminal and the Honeywell WLAN Security Supplicant is not loaded.

By default, the Wireless Zero Config is disabled and the supplicant is loaded.

This icon appears only if you removed the supplicant and cold boot the terminal.

See Page

7-11

7-4

7-6

7-8

7 - 1

Using the IrDA Port

Using the IrDA port, you can send and receive data between the terminal and other devices equipped with infrared. This can include, but is not limited to, Windows Mobile information such as Contacts and Tasks, as well as software upgrades.

The maximum data transfer speed is 115 Kbps.

IrDA Port Location

IrDA Port

To send or receive, the IrDA ports of both devices - whether it’s two terminals, or a terminal and a host device - must be aligned with each other and within a close range. The maximum data-transfer speed is 115 Kbps.

Sending Data

1. Align the IrDA ports.

2. Open the program where you created the item you want to send and locate the item in the list. You can also beam files, but not folders, from File Explorer.

3. Tap and hold the item and select Beam File.

4. The IrDA port searches for a receiving IrDA port in the vicinity. The selected device reads “Pending.”

7 - 2

5. When the IrDA port finds the aligned IrDA port, it immediately starts sending the selected file. The selected device reads “Sending.”

6. When the file transfer is complete, the selected device reads “Done.”

Receiving Data

The Beam Setting must be set to receive all incoming beams from other infrared devices.

1. Verify that beam settings are set to receive. Tap Start > Settings > Connections > Beam. The Beam Settings window should appear as follows:

2. Align the IrDA ports.

3. Have the owner of the other device send the information to you.

4. Your terminal automatically begins receiving it.

5. A popup message appears asking if you want to receive the incoming file.

6. Tap Yes to receive the file.

7 - 3

Connections Manager

Microsoft’s Connections Manager sets up multiple network connections to Internet Service Providers (ISPs) via external modem.

Do NOT enter connection parameters in the Connections Manager if:

• You are using one of the on-board wireless radios to connect to a network.

The Dolphin terminal uses the settings from each radio’s configuration utility to connect.

• You are using Wireless Zero Config. By default, WZC is disabled on Dolphin terminals.

To Access the Connections Manager

Tap Start > Settings > Connections > Connections icon .

Task Tab

The Task tab enables you to initially configure, then manage network settings when using a modem. Select an item in this list and then complete the setup screens that follow with the appropriate information for your network.

My ISP

The links under this heading enables you to add and manage modem connections to an ISP. To complete the setup screens, obtain the following information from your ISP:

• ISP dial-up access telephone number

• Username

• Password

• TCP/IP settings

My Work Network

These links enable you to establish the following connections types:

• Modem

• Virtual Private Network (VPN)

• *Proxy server connection

To complete the setup screens, obtain the network parameters from your system administrator.

7 - 4

*Proxy Server Connections If you are connected to your ISP or private network during synchronization, the terminal should download

the proper proxy settings during synchronization with the PC. If these settings are not on your PC or need to be changed, ask your ISP or network administrator for the proxy sever name, server type, port, type of Socks protocol used, and your user name and password.

Modify an Existing Connection

Manage Existing Connections appears on the Connections tab after at least one network connection has been established.

Tap Manage Existing Connections on the Tasks tab and follow the setup screens.

Advanced Tab

The Advanced tab enables you to select the default network, dialing rules, and IP address exceptions for modem connections.

Note: You should not need to change Advanced settings because most ISPs now use DHCP addresses.

Online Help

For more information about modem connection setup, consult the online help on the setup screens by tapping the Help icon .

7 - 5

Dolphin Wireless Manager

The Dolphin Wireless

Manager

provides a centralized interface that enables and disables all the on-board radios. Each radio has its own configuration program. The Dolphin Wireless Manager also provides shortcuts to the configuration utilities for each radio.

Dolphin Wireless Manager Window

Tap Start > Settings > Connections > Dolphin Wireless Manager .

If a rectangle is grayed-out, then the radio is not installed on the terminal.

Enabling the Radios

1. Tap Start > Settings > Connections tab > Dolphin Wireless Manager.

These buttons show you the state of the radio.

If applicable, information about the radio appears when the radio is activated.

2. Tap anywhere inside the rectangle or the OFF button inside the rectangle.

3. The radio begins activating.

7 - 6

4. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON.

Note: If applicable, information about the radio appears in the rectangle.

Accessing Radio Configuration Utilities

Each of the three radios have their own configuration utilities that you can access through the Menu.

There are three radio configuration utilities:

For 802.11a/b/g: Tap WLAN Settings and the Honeywell WLAN Security Supplicant opens.

The Honeywell WLAN Security Supplicant User’s Guide is available for download from the Dolphin 9700 product page at www.honeywellaidc.com.

For Bluetooth: Tap Bluetooth Settings and the Bluetooth Settings open.

For details, see Working with the Bluetooth Radio on page 9-1.

For GSM: Tap Phone Settings and the Phone opens.

For details, see Working with GSM on page 8-1.

7 - 7

ActiveSync Communication

synchronize and configured for the appropriate communication type on the host workstation and the Dolphin terminal. Dolphin terminals ship with ActiveSync already installed. Therefore, if ActiveSync is already installed on the host workstation, you just need to connect the Dolphin terminal to the host workstation (via Dolphin peripheral) to initiate communication.

If ActiveSync 4.5 or higher is not installed on the host workstation, you can download and install the most current version of ActiveSync from www.microsoft.com.

When communicating via ActiveSync, your terminal is designed to be connected to the host workstation with

a communication peripheral

of any peripheral not sold/manufactured by Honeywell may cause damage not covered by the warranty.

Capabilities

• Back up and restore your device data.

• Copy (rather than synchronize) files between your device and workstation.

• Control when synchronization occurs by selecting a synchronization mode. For example, you can

synchronize continually while connected to your workstation or only when you choose the synchronize command.

• Select which information types are synchronized and control how much data is synchronized. For

example, you can choose how many weeks of past appointments you want synchronized.

data between the terminal and the workstation, ActiveSync 4.5 or higher must be installed

sold/manufactured

by Honeywell, such as the

charge/communication

cable. Use

Communication Types

The Dolphin terminal supports the following types of communication via ActiveSync through its I/O

Connector (see page 3-10) on the bottom panel:

USB The USB cable and hardware peripherals allow the terminal to communicate with a workstation or

RS232 The RS232 cable allows the terminal to communicate with a workstation, modem, or any RS232

to networked through a USB hub. The Dolphin terminal supports full-speed USB communication (USB 1.1); maximum data transfer rate is 12 Mbps. The Dolphin terminal defaults to USB communication out of the box.

device. Maximum data transfer rate is 115 Kbps.

Hardware Requirements for Setup

• Dolphin communication peripheral or cable

• Dolphin power cable from Honeywell

• USB cable (for USB communication)

• Serial cable (for RS232 communication)

Software Requirements for Communication

• To sync successfully, ActiveSync v4.5 or higher must be configured for same communication type on

both the host workstation and the Dolphin terminal. ActiveSync must be setup on your workstation before you initiate synchronization from the terminal for the first time.

• Windows 98 Second Edition, Windows Me, Windows 2000, Windows NT (4.0 SP6 or higher), Windows

XP, or Windows Vista operating systems.

7 - 8

Setting Up the Host Workstation

Verify that ActiveSync is configured to use the appropriate communication type by clicking File > Connection Settings.

For USB communication, check Allow USB connections.

Note: You can have both USB and RS232 selected in the software without affecting processing. However, your

hardware setup should use only RS232 or USB, not both.

For RS232 communication, connect to COM1.

Communicating with the Dolphin Terminal

After setting up both the workstation and the terminal, ActiveSync connection should be automatic.

1. Connect the Dolphin terminal to a Dolphin communication peripheral.

2. The Dolphin terminal automatically opens ActiveSync to establish a connection.

Synchronizing with the Host Workstation

After setup, synchronization begins automatically whenever the terminal’s mechanical connector connects to a Dolphin peripheral that is connected to a host workstation with ActiveSync installed.

Exploring the Terminal from the Workstation

When the Dolphin terminal and workstation are connected, open the main ActiveSync window (on the desktop), and click Explore.

The Mobile Device folder opens in Windows Explorer.

The Dolphin terminal is now treated as a mass storage device, and transferring files is as simple as dragging and dropping or copying and pasting.

7 - 9

Installing Additional Software

In addition to the default programs installed on your terminal when it is first booted up, you can install any program (created for a Windows Mobile-based device), as long as the terminal has enough memory to store the program and the program has an EXE, CAB, or DLL extension.

The most popular place to find software on the Windows Mobile website: www.microsoft.com/

windowsmobile/products/pocketpc/

When selecting programs, verify that the program and version of the program are designed for Windows

Mobile and your processor. You can verify your processor by tapping Start > Settings > System > About >

Version. Make a note of the information in the Processor field.

You can install additional software via:

• ActiveSync - see page 7-10.

• Infrared - see page 7-2.

• Network connection (via wireless radio) - see page 7-11.

• Connect to your ISP.

Adding Programs to the Terminal Using ActiveSync

When selecting programs, verify that the program and version of the program are designed for Windows

Mobile and your processor. You can verify your processor by tapping Start > Settings > System > About >

Version. Make a note of the information in the Processor field.

Depending on the application, the software must be stored or installed on the host PC.

1. Download the program to your desktop computer from either the Internet or the CD or disk that con-

tains the program. You may see a single EXE or setup.exe file, a CAB file, or DLL. There may also be several versions of files for different device types and processors.

2. Read any installation instructions, Read Me files, or documentation that comes with the program.

Many programs provide special installation instructions.

3. Connect the terminal to the desktop computer via a Honeywell communication peripheral.

If the File is an Installer:

An installer program is one that installs on the PC and the terminal simultaneously; one process installs to both devices.

1. On the PC, double-click the EXE or *.setup.exe file. The installation wizard begins.

2. Follow the directions on the PC screen. The installation process includes transferring the software to

the terminal.

If the File is Not an Installer:

Some programs cannot be installed on PCs because they are designed for terminals. In these cases, the appropriate files must be stored on the host PC, transferred via ActiveSync, and installed on the terminal. You will know the program cannot be installed on the PC if an error message appears when you try to install it stating that the program is valid but designed for a different type of computer.

1. If you cannot find any installation instructions for the program in the Read Me file or documentation,

open ActiveSync and click Explore.*

2. Click on the My Windows Mobile-Based Device folder and copy the program file or files to

the Program Files folder on the terminal.

7 - 10

• If you want the program to be part of the Autoinstall that occurs after every hard reset, place the program file in the Autoinstall folder (My Windows Mobile-Based Device > IPSM > Autoinstall).

3. Depending on the program, you may need to open File Explorer on the terminal, navigate to the folder where the program is located, and tap on the program file to install it.

• If you copied the file to the Autoinstall folder, you can either tap on the program inside the Autoinstall folder or perform a hard reset and the program will install as part of the Autoinstall process that occurs during each hard reset. Remember, a hard reset erases RAM data! For more information, see Hard Reset (Cold Boot) on page 3-16.

After installation on the terminal is complete, tap Start and the program and its icon appears on the Start screen. Tap it to open the program.

Adding Programs Directly from the Internet

When selecting programs, verify that the program and version of the program are designed for Windows

Mobile and your processor. You can verify your processor by tapping Start > Settings > System > About >

Version tab. Make a note of the information in the Processor field.

1. Determine your device and processor type so that you know which version of the software to install. Tap Start > Settings > System > About. On the Version tab, make a note of the information in the Processor field.

2. Download the program to your device straight from the Internet using Internet Explorer Mobile. You may see a single EXE or setup.exe file, or several versions of files for different device types and processors.

3. Read any installation instructions, Read Me files, or documentation that comes with the program. Many programs provide special installation instructions.

4. Tap the file, such as an EXE file. The installation wizard begins. Follow the directions on the screen.

5. Select the radio or radio combination and tap Apply. The Radio Manager begins enabling your radio or radio combination.

6. When enabled, the Status field reads “Success”.

7 - 11

9700 COM Port Assignment Table

COM Port

COM0

COM1

COM2

COM3

COM4

COM5

COM6

COM7

COM8

Description

Unused Serial Port: RS232 Connector on the bottom panel Not accessible IrDA: Serial Infrared (SIR) up to 115 Kbps Not accessible Bluetooth DUN IrCOMM

GPS: COM Port for the GPS receiver USB Serial: Virtual USB Serial port for ActiveSync

COM9

Bluetooth BTHATCI server

7 - 12

Working with

GSM

Overview

The Dolphin 9700 terminal can be configured with an integrated, module for WWAN communication.

GSM Short for Global System for Mobile communications, GSM is an open, non-proprietary wireless

GPRS Short for General Packet Radio Service, GPRS is a non-voice value added service that allows

Requirements

WAN system that is constantly evolving and growing.

packet-switched data to be instantly sent and received across mobile telephone networks.

Using GSM/GPRS requires a:

• Network subscription to a GSM/GPRS network (you need to know what service providers are in your geographic area), and

• An installed SIM card that has been activated by the network service provider (see SIM Card

Installation on page 8-2).

embedded

GSM/GPRS

quad-band

Quad Band Antenna

The GSM radio features an internal antenna that is optimized for power output and receiver sensitivity. This is an omni-directional antenna with zero dBm gain.

For the MC-75 radio, there are two different antennas based on geographical location; each supports two bandwidths:

Europe: Supports 900 MHz and 2100 MHz bands. North America: Supports 850 MHz and 1900 MHz bands.

Signal Strength

The signal strength of the GSM connection is indicated by the number of bars that appear in the signal strength icon in the Navigation bar at the top of the window.

Icon Indicates…

The signal strength of the radio connection.

The signal strength of the phone (voice) connection; see page 8-5.

The signal strength of the data connection; see page

8-8

radio

8 - 1

Voice and Data Communication

Dolphin terminals with integrated GSM/GPRS radios are optimized for the following two-way voice and data communications:

Voice: GSM voice data ("dial-up") Data: GPRS Class 10

Data

transmissions

average 40-60 Kbps (available speed depends on the wireless network carrier).

You can use the GSM radio for voice communication and data communication but not at the same time. If you want to communicate over the phone (voice), you cannot send data. If you want to send data, you cannot use the phone.

SIM Card Installation

Short for Subscriber Information Module, a SIM card stores the subscriber's personal information, GSM/ GPRS radio settings, security keys, contacts, etc. SIM cards are installed in compatible mobile devices, enabling you to switch devices without losing personal and setup information.

SIM Card Requirements

Before installing the SIM card:

• The SIM card must be activated by the service provider.

• The terminal must be powered down.

Note: If no SIM card is installed, you can still make emergency phone calls such as 9-1-1, for example.

To Install a SIM Card

Access to the SIM card is located under the battery.

1. Put the terminal in suspend mode and lay it face down on a flat surface.

Door

Battery

Interface

MicroSD Card

2. Remove the battery door and battery pack.

SIM Card

3. Unlock and lift up the access door to the SIM card socket.

4. Insert your SIM card. Make sure the interface on the card is connected to the SIM Card interface in the slot; align the beveled corner of the card with the beveled corner of the socket.

8 - 2

5. Close and lock the SIM card door to secured SIM card in place.

New Image Required.

6. Install the battery pack and battery door.

7. Turn on the terminal.

8 - 3

Enabling the GSM Radio

Be default, the GSM radio should be enabled after each hard reset. Verify the status of the radio in the Dolphin Wireless Manager.

Tap Start > Settings > Connections tab > Dolphin Wireless Manager

If the Phone is set to OFF, tap the Phone rectangle and the GSM radio enables.

8 - 4

Voice Communication

You can use the Dolphin terminal as a phone over the GSM radio.

Audio Modes

The back panel of the 9700 contains both a speaker and a microphone that you can use to send and receive audio signals over the GSM network; see Back Panel: 9700 on page 3-6.

There are two audio modes:

Headset Headset mode is when you plug a headset into the audio jack and speak into the microphone. You

Hands-Free Hands-free mode is when you use the back panel as a speakerphone. To switch the back panel to

must use a 2.5mm plug; no other audio plug will fit. speakerphone, in the Dialer, tap Settings > Speakerphone. The audio levels adjust appropriately

for speakerphone use.

Volume Control

VOL

Blue

Use the Dolphin keyboard to manually adjust the volume. To raise the volume, press the Blue modifier key + up arrow. To lower the volume, press the Blue modifier key + down arrow.

Accessing the Dialer Window

When the GSM radio is active, tap Start > Settings > Connections tab > Dolphin Wireless Manager, then tap Menu > Phone Settings. The Phone dialer opens.

Displays the network carrier from the SIM card.

Displays the most recent calls.

Dialing

Once the dialer window is open you can dial out two ways:

• Tap the buttons on the dialer window.

• Use the physical keyboard (when it’s in numeric mode).

8 - 5

Sending Calls

After the number is dialed, tap Talk or use the keyboard.

Note: The icon indicated that the phone is in use.

Ending Calls

While the phone call is live, tap End or use the physical keyboard.

Keyboard Combinations for Calls

Keyboard

43-key keyboard 56-key keyboard

View Options

Tap Menu > View.

To Send a Call, Press… To End a Call, Press…

Blue + NUM Blue + SFT

Blue + ENT Blue + ENT

8 - 6

Setup Options

Tap Menu > Options.

The Phone Settings tab windows appear.

Phone Tab Services Tab Network Tab

Establish or change a PIN on the Phone tab.

For each service, the phone will read settings from the network on the SIM and display the available from

the carrier.

You can set networks on the Network tab.

options

8 - 7

Data Communication

You set up data communication via the connections manager. The carrier on the SIM card is the ISP.

System Requirements

• The GSM radio must be enabled; see Enabling the GSM Radio on page 8-4.

• You must have an active SIM card installed; see SIM Card Installation on page 8-2.

• The Phone must not be in use. The in the navigation bar indicates that the GSM phone is active but

the phone is not in use.

Information Requirements

You must have from the SIM card carrier:

• The APN (access point name) number.

• The username and password of the account.

Establishing Data Communication

1. Tap Start > Settings > Connection tab > Connections

2. Under My ISP, tap Add a new modem connection.

3. Enter a name for the connection, Select Cellular Line (GPRS) as the modem, and Tap Next.

8 - 8

4. Enter the APN and tap Next.

5. Enter the username and password from the account and tap Finish.

6. On the Connections window, tap Manage existing connections. The connection you just created should appear in the list on the modem tab.

8 - 9

7. Tap and hold on the connection and select Connect on the popup menu.

8. The network icon in the navigation bar indicates the GSM radio is attempting to connect .

9. When the connection is complete, the network icon changes to: .

10. You can now send data over GSM.

Ending the Data Connection

You need to end the data connection to use the phone. By default, the data connection will disconnect after a certain amount of time passes without use. This period of time is determined by ISP.

To end the data connection manually, tap the network icon in the navigation bar and select Disconnect on the popup bubble.

8 - 10

Roaming

You can select automatic or manual roaming. The Phone defaults to automatic roaming.

1. When an active SIM card is inserted in the terminal, tap Start > Settings > Personal tab > Phone

2. Select the Network tab.

. The Phone Settings window appears.

3. Under Network selection, select Automatic (the default selection) or Manual. a. If you select Manual, the Phone searches for available networks.

b. The found networks appear.

c. Select a new network and tap OK. The Phone registers on the new network and the Network

tabs appears.

d. To switch to another network, tap the now active Select button and the process repeats.

4. To switch back to automatic roaming, select Automatic under Select networks and tap OK.

8 - 11

8 - 12

Working with the Bluetooth

Radio

Enabling the Bluetooth Radio

You enable the Bluetooth radio in the Dolphin Wireless Manager (see page 7-6).

1. Tap Start > Settings > Connections tab > Dolphin Wireless Manager

2. Tap anywhere inside the Bluetooth rectangle and Bluetooth begins activating.

3. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON.

Now, the Bluetooth radio is transmitting a signal. Additional text in the Bluetooth section tells information about the Bluetooth radio. “Visible” and “Not visible” indicates whether the Bluetooth radio is discoverable or not discoverable by other Bluetooth devices.

Now, you can connect to other transmitting and discoverable Bluetooth devices (see page 9-2). To make the terminal discoverable for other Bluetooth devices, you need to make the Bluetooth radio

discoverable (see page 9-8).

9 - 1

Connecting to Other

Bluetooth

Devices

You need to perform a device discovery and then select a discovered device and connect to it. Pairing happens as part of the connection process.

1. In the Dolphin Wireless Manager, tap Menu > Bluetooth Settings. OR

Tap Start > Settings > Connections tab > Bluetooth

2. Tap Add new device. The terminal begins searching for discoverable Bluetooth devices.

3. Select a device in the list and tap Next.

9 - 2

4. You are prompted to enter a passcode.

If the device has a specific passcode, enter it in the Passcode field and tap Next. If the device does not have a specific passcode, enter one in the Passcode field and tap Next.

The Bluetooth radio tries to connect with the device.

5. If you created a passcode, you will be prompted by the other device to enter the same passcode. Enter the created passcode to establish a paired connection. (If you entered a the passcode from the device, you shouldn’t have to do anything on the other device.)

6. When the connection is complete, a list of matching and supported services on the device appears.

7. Select the services you want to use and tap Finish. The services on the new devices have to be selected or else the pairing won’t include those services, even though the devices are paired. If services are not selected, you will be continually reprompted for the passcode from the device.

9 - 3

8. The device appears in the list on the main window.

9. After the passcodes have been accepted on both sides, you have a trusted (“paired”) connection.

Pairing and Trusted Devices

The terminal does support pairing. Pairing happens during general connection setup. Paired devices are "trusted" devices. This means that there is unrestricted access to all services (including services that require authorization and authentication).

A connection can exclude pairing. A device that is connected to the terminal but not paired with it is considered an untrusted device. Content can still be passed to untrusted devices by requiring authorization with each attempt (for example, with the initialization of a file exchange). The Beam File method of file transfer can be used to pass a file as an untrusted device; see Transferring Files on page

9-7.

9 - 4

Types of Devices and Services

When you tap Add new device on the Devices tab, the Bluetooth radio scans for discoverable Bluetooth devices in range, which are Bluetooth devices that have been made discoverable.

Device Types

The types of devices in the vicinity of the radio appear in the list of discovered devices.

Supported Services

Only the services that are mutually supported on both devices appear on the Partnership Settings window.

9 - 5

Connecting to Bluetooth Printers

1. Make sure the Bluetooth printer is in range and set to be discoverable by other Bluetooth devices.

2. Look up the Bluetooth printer’s broadcasted ID.

3. Perform a device discovery (Tap Settings > Connections > Bluetooth > Add new device.)

4. Look for the Bluetooth printer’s broadcasted ID in the list of discovered devices.

5. Click on the Bluetooth printer’s ID and wait for the prompt to enter a Passcode.

6. Enter the Passcode and tap Next. The passcode may default to either "1111" or "0000." If there is no default, consult the printer literature for the number.

7. Select a printing-related service in the list of services.

8. Tap Finish to establish the connection on the terminal.

9. Complete any additional steps required by the printer.

Connecting to Bluetooth Headsets

1. Make sure the Bluetooth headset is in range and set to be discoverable by other Bluetooth devices.

2. Look up the headset’s broadcasted ID.

3. Perform a device discovery (Tap Settings > Connections > Bluetooth > Add new device.)

4. Look for the headset’s broadcasted ID in the list of discovered devices.

5. Click on the headset’s ID and wait for prompt to enter a passcode.

6. Enter the Passcode and tap Next. The passcode may default to either "1111" or "0000." If there is no default, consult the printer literature for the number.

7. Select Headset in the list of services.

8. Tap Finish to establish the connection on the terminal.

9. Complete any additional steps required by the headset.

9 - 6

Transferring Files

1. Tap Start > Programs > File Explorer.

2. Navigate to the file you want to transfer.

3. Tap and hold on the file and select Beam File on the popup menu.

4. The Bluetooth radio begins searching for devices.

5. Tap the device to begin sending the selected file.

When a Bluetooth device is first found, it

appears

an Unknown device; the

icon indicates that the device is a Bluetooth device.

As data is retrieved, the device IDs appear in the list.

6. While trying to connect, the selected device reads “Pending.”

7. When the file is being transferred, the selected device reads “Sending.”

9 - 7

Making the Terminal Discoverable

By default, the Dolphin terminal is not discoverable, which means that the terminal will not be found by other Bluetooth devices.

To make the terminal discoverable, tap the Mode tab.

Select Make this device visible to other devices and tap OK.

Selecting COM Ports

You can select COM ports 0-9. For more information, see 9700 COM Port Assignment Table on page 7-

12.

9 - 8

Honeywell 9700L0P, 9700LUP Users Manual

Specifications and Main Features

Frequently Asked Questions

User Manual