8680i
Wearable Scanner |
|
|
|
|
|
|
y |
||
Quick Start Guide |
|
|
|
|
r |
||||
|
ina8 |
||||||||
|
|
|
|
|
|
||||
|
|
|
|
m |
|
|
1 |
||
|
|
li |
|
|
|
|
/ |
||
|
|
|
|
|
3 |
||||
|
e |
|
|
|
|
||||
|
|
|
|
1 |
|
||||
r |
|
|
|
|
|
|
|||
|
|
|
|
/ |
|
|
|||
|
|
|
3 |
|
|
||||
P |
|
|
|
|
|
|
|||
|
|
|
t |
|
|
|
|
||
|
|
|
|
f |
|
|
|
|
|
|
|
|
a |
|
|
|
|
|
|
|
|
r |
|
|
|
|
|
|
|
D |
|
|
|
|
|
|
|
8680-EN-QS Rev (a)
3/18
Overview
Battery
|
|
Battery |
|
Right button |
latch |
|
|
|
|
Left button |
|
Trigger |
User window |
Scanner |
Note: The battery must be fully charged before the first use. An MB4-BAT-SCN02 or an MB4-SCN02 Charging Station must be purchased separately.
1
Attach the Scanner to Your Hand
1.Slide your fingers into the loosened strap.
2.Pull the strap to secure to your fingers.
2
Right or Left Handed Operation
To release the finger trigger, turn over the scanner. Slide the latch toward the user window to release the finger trigger. Turn the finger strap around and snap it into place to change the operation to the correct hand.
3
Power Up the Scanner
Press the trigger for 10 seconds to power up the scanner. The battery, WiFi, and Bluetooth status appears in the window.
Wrist Position When Scanning
Warning: Do not stare directly into the laser beam.
How to Scan a Bar Code
The 8680i scanner has a view finder that projects a bright aimer line. This aimer line should be centered over the bar code, but it can be positioned in any direction for a good read.
4
Linear bar codes |
2D Matrix symbol s |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The aimer line is smaller when the scanner is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit. Symbologies with larger bars or elements (mil size) should be read farther from the unit. To read single or multiple symbols (on a page or on an object), hold the scanner at an appropriate distance from the target, press the trigger, and center the aimer line on the symbol. If the code being scanned is highly reflective (e.g., laminated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted reflection.
5