Granit™ XP 1991i
Cordless Industrial Area-Imaging Scanner
Quick Start Guide
1991-EN-QS-01 Rev A
5/20
Agency Model: 1991i, 1991iSR, 1991iXR
Note: Refer to your User Guide for information about cleaning
your device.
Getting Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
When the base is connected and powered up, put the scanner in
the base to establish a link. The green LED on the base flashes
to indicate the scanner’s battery or charge pack is charging.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.
1
Connecting the Base
USB:
Note: If you are charging the scanner using the USB cable, the
current available for charging is reduced and charge times
are increased. Charging via the power supply is faster.
2
Keyboard Wedge:
3
RS232 Serial Port:
4
Reading Techniques
SR Models: XR Models:
Standard Product Defaults
The view finder projects an aiming beam that should be centered over the barcode, but it can be positioned in any direction
for a good read.
Note: If the scanner beeps 3 times when scanning a barcode, the
link has not been established. If the scanner beeps once,
the link has been established.
Standard Product Defaults
The following barcode resets all standard product default settings.
5
USB Serial
USB Serial
USB PC Keyboard
If you are using a Microsoft® Windows® PC, you must
download a driver from the Honeywell website. The
driver will use the next available COM Port number.
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automatically use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
6
Keyboard Country
USA (Default)
Belgium
Denmark
Finland
France
Germany/Austria
Scan the appropriate country code below to program the keyboard layout for your country or language. By default, national
character replacements are used for the following characters:
#$@[\]^‘{|}~. Refer to the ISO 646 Character Replacements chart
in your User Guide to view the character replacements for each
country.
7
Note: For a complete list of country codes, see the User Guide for
Great Britain
Italy
Norway
Spain
Switzerland
Locked Link Mode
(Single Scanner)
your product.
Locked Link
If you link a scanner to a base using the Locked Link Mode,
other scanners are blocked from being linked if they are inadvertently placed into the base. If you do place a different scanner into the base, it will charge the scanner, but the scanner will
not be linked.
8
To use a different scanner, you need to unlink the original scan-
Override Locked Scanner
Unlink Scanner
ner by scanning the Unlink Scanner barcode.
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a
base, scan the Override Locked Scanner barcode with a new
scanner, and place that scanner in the base. The locked link will
be overridden; the broken or lost scanner’s link with the base will
be removed, and the new scanner will be linked.
Unlinking the Scanner
If the base has a scanner linked to it, that scanner must be
unlinked before a new scanner can be linked. Once the previous
scanner is unlinked, it will no longer communicate with the
base. Scan the Unlink Scanner barcode to unlink a scanner.
9
Trigger
Manual Trigger - Normal
(Default)
Presentation Mode
Streaming Presentation Mode
The following barcodes will allow you to use the scanner in
Manual Trigger - Normal Mode (need to press the trigger to
read) or Presentation mode (the scanner is activated when it
“sees” a barcode).
Note: Presentation Mode continuously draws power, so use of
the external power supply is recommended for this mode.
Streaming Presentation™
When in Streaming Presentation mode, the scanner leaves the
scan illumination on all the time and continuously searches for
barcodes.
10
Suffix
Add CR Suffix
Add Tab Suffix
Remove Suffix
Add Code ID Prefix To All Symbologies
(Temporary)
If you want a carriage return after the barcode, scan the Add CR
Suffix barcode. To add a tab after the barcode, scan the Add Tab
Suffix barcode. Otherwise, scan the Remove Suffix barcode to
remove the suffixes.
Add Code ID Prefix to all Symbologies
Scan the following barcode if you wish to add a Code ID prefix to
all symbologies at once.
Note: For a complete list of Code IDs, see the User Guide for your
product.
11
Function Code Transmit
Enable
(Default)
Disable
When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are
provided in your User Guide. When the scanner is in keyboard
wedge mode, the scan code is converted to a key code before it
is transmitted.
12
Support
To search our knowledge base for a solution or to log into the
Technical Support portal and report a problem, go to
www.hsmcontactsupport.com.
User Documentation
For the user guide and other documentation, go to
www.honeywellaidc.com.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and
click Resources > Product Warranty.
Patents
For patent information, see www.hsmpats.com.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make
changes in specifications and other information contained in
this document without prior notice, and the reader should in all
cases consult HII to determine whether any such changes have
been made. The information in this publication does not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of
this material. HII disclaims all responsibility for the selection
and use of software and/or hardware to achieve intended
results.
13
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into
another language without the prior written consent of HII.
Copyright2020 Honeywell International Inc. All rights
reserved.
14
Loading...