Honda Power Equipment F200 User Manual

This manual covers operation and maintenance of the F200 tiller. All information in this publication is based on the latest product information available at the time of approval for printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. The manual should be considered a permanent part of the tiller and remain with the tiller when sold. Read the manual carefully. Pay special attention to statements preceded by the following words:

Indicates a strong possibility of severe personal injury or loss of life if instructions are not followed.

CAUTION:

Indicates a possibility of personal injury or equipment damage if instructions are not followed.

NOTE:

Gives helpful information. Thank you for purchasing a Honda Tiller. If a problem should arise, or if you have any questions about the tiller, consult an authorized Honda dealer.

The Honda tiller is designed to give safe and dependable service if operated according to instructions. Read and understand the Owner’s Manual before operating the tiller. Failure to do so could result in personal injury or equipment damage.

No part of this publication may be reproduced without written permission. 0 Honda Motor Co., Ltd., 1980

2

IMPORTANT NOTICE

I

This tiller is not equipped with a spark arrester. Operation on forest, bush or grass covered land may be illegal in some states. Check local laws and regulations before operation.

SAFE OPERATION

B To ensure safe operation

l

Never permit anyone to operate the tiller without proper instruction.

l

Know how to stop the tiller quickly and understand the operation of all the controls - READ THIS OWNER’S MANUAL CAREFULLY.

l

Keep children and pets at a safe distance when tilling.

l

Clear the area to be tilled by picking up any stones, wire, glass, large sticks, metal, etc.

l

Always stop the engine before cleaning the tines or making adjustments.

l

Never operate the tiller without the recoil starter.

l

Stop the engine whenever you leave the tiller.

Never allow it to idle unattended.

l

If you strike an object while tilling, stop the

engine and check the tiller for damage.

l

When tilling on an incline, keep the fuel tank less

than half full to minimize fuel spillage.

l

Make sure that all fasteners are properly secured.

l

Wear suitable clothing and shoes while using the tiller.

l

Whenever carrying the tiller, make sure to stop

the engine; or the rotor may turn even if the clutch is disengaged.

COMPONENT IDENTIFICATION

1. Fuel tank cap

2. Fuel valve

3. Air cleaner

4. Muffler

5. Throttle lever

6. Front wheel

7. Engine switch

6

1. Clutch lever

2. Recoil starter

3. Spark plug

4. Drag bar

5. Mission oil level check bolt

6. Mission oil filler cap

7. Engine oil filler cap Engine oil drain bolt

8.

9. Rotor

OPERATION

Pre-Operation Check Always check the following before

using the tiller:

(A) Engine oil

level

(B) Transmission oil level.

(C) Air cleaner condition. (D) Fuel level.

A. ENGINE OIL LEVEL

CAUTION:

engine

Engine oil is a major factor affecting

performance and service life. Non-detergent

or vegetable oils are not recommended.

7

Oil Recommendation

Use Honda 4-stroke oil or an equivalent. Use only high detergent, premium quality motor oil certified to meet or exceed US automobile manufacturer’s requirements for Service Classification SE, in the engine and transission. Motor oils intended for Service SE will show this

designation on the container. The regular use of special oil additives is unnecessary and will only increase operating expenses.

CAUTION:

Engine oil quality is a major factor affecting the performance and service life of the engine.

Nondetergent or vegetable oils are not

recommended.

Recommended oil viscosity

SAE low-40

Other viscosities shown in the chart below may be used when the average temperature in your area is within the indicated range. With the tiller on a level surface, remove the oil filler cap and check the oil level. If the level is low, fill to the upper level with the recommended oil.

CAUTION:

Insufficient oil will cause overheating

and subsequent wear.

(1) Oil filler hole (3) Upper limit (2) Oil filler cap

(4) Lower limit

8

B. TRANSMISSION OIL LEVEL With the tiller on a level surface remove the oil level

check bolt and check if the oil flows out of the bolt hole. If the oil level is low, reffi with the recommended oil till it flows out of the bolt hole.

C. AIR CLEANER CONDITION Remove the cover and inspect the elements, clean

them if necessary (see p. 19).

(1) Oil level check bolt (2) Oil filler cap

(3) Air cleaner cover

(4) Air cleaner elements

9

Honda Power Equipment F200 User Manual

CONTENTS

SAFE OPERATION

COMPONENT IDENTIFICATION

OPERATION

Oil Recommendation