Honda Ridgeline (2022) Navigation Manual

Navigation Manual

2022 RIDGELINE

The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd., reserves the right,

NOTICE

3 WARNING

however, to discontinue or change specifications or design at any time without notice and without incurring any obligation.

Accessories Precautions

The GPS antenna is located in the dashboard. Metallic front or side window tinting can seriously degrade or obstruct GPS reception.

Signal noise from devices such as radar detectors, vehicle tracking devices, remote starters, and additional amplifiers can disrupt the navigation system. If you install any such item, install it away from the navigation display and antenna.

Important Safety Information

Using the navigation system while driving can take your attention away from the road, causing a crash in which you could be seriously injured or killed.

Only operate system controls when the conditions permit you to safely do so.

Avoid focusing on the screen or manually operating the system controls while driving.

Certain on-screen controls are disabled when driving, however most of the voice commands continue to function. Pull to the side of the road if you need to devote more attention and time to look at the screen or access additional menus.

Route guidance may conflict with street closures, road construction, detours, and out-of-date map data.

The system itself may also have limitations. Verify route information by carefully observing roads, signs, and signals. Always use your own judgment and obey traffic laws.

System Limitations P. 130

This vehicle’s navigation display, if so equipped, includes mercury-containing components. Upon removal, please reuse, recycle, or dispose of as hazardous waste.

Clean the screen with a soft, damp cloth. You may use a mild cleaner intended for use on navigation screens.

2 System Setup P. 15

Start-up 16 Personal Information 18 Display Mode Settings 26 Map & Vehicle 28 Navigation 36 Traffic 45 Other Settings 46 Data Reset 52

2 Navigation P. 53

Entering a Destination 54 Calculating the Route 74 Driving to Your Destination 77 Map Operation 81 Changing Your Route 91 Changing Your Destination 94

2 Other Features P. 107

About Apps Menu 108 ecoRouteTM109 Information Functions 117

2 Troubleshooting P. 123

Troubleshooting 124

2 Reference Information P. 129

System Limitations 130 Customer Assistance 132 Legal Information 134

2 Voice Commands P. 137

Voice Commands 138 List of Categories 140

Quick Reference Guide

System Setup

Navigation

Other Features

Troubleshooting

Reference Information

Voice Commands

Index

P. 2

P. 15

P. 53

P. 107

P. 123

P. 129

P. 137

P. 141

Quick Reference Guide

Store home address (P18 )

1 home address.

Track route (P77 )

Follow your route in real-time with voice guidance.

Store Save Locations (P19)

Store locations to use as the destination.

Enter destination (P54)

Select your destination using several methods.

Select route (P75)

Set route preferences and select one of the available routes.

Avoid certain areas (P39)

Set streets and areas to detour around.

Add waypoints (P93)

Add “pit stops” along your route.

Traffic Information* (P86)

View and avoid congestion and traffic incidents.

*: Available only in certain areas.

Overview—Functions at a Glance

Navigation

You can select any place/landmark as a destination by using the touchscreen. The navigation system gives you turn-by-turn driving directions to your destination.

Quick Reference Guide

HOME Screen

(Home)

Display the HOME screen.

(Menu)

Display the map menu.

(Back)

Go back to the previous screen.

(Display Mode) Switch between Day and Night modes manually. VOL (Volume) Increase or decrease the audio volume.

Display the map screen.

Navigation

Display the navigation feature that was used the last time. At start-up, the navigation top screen is displayed.

GPS signal strength (P121)

Display the satellites' status.

Where To? (P54)

Select search methods to enter a destination for route guidance.

Apps (P108)

Display the useful functions incorporated into the navigation system.

View Map (P6)

Display the map screen.

Settings (P15)

Change the settings for the navigation functions.

The system displays various functions from the HOME screen. Press the (Home) icon at any time to return to the main HOME screen.

Navigation Top Screen

Display the map screen and operate the navigation features. From the HOME screen, select and then press the (Back) icon. The navigation top screen is displayed.

Quick Reference Guide

Touchscreen Operation

You can operate the system using your finger on the touchscreen. The touchscreen can be operated if you are wearing thin gloves, but it may be more difficult for the system to respond.

Tap

Touch the screen lightly with your finger to select an option on the screen.

Swipe

Lightly sweep your finger side to side or up and down to scroll a list or map.

You can change the touchscreen sensitivity setting.

2 Refer to the Owners Manual.

Slide

Move your finger slowly across the screen to scroll the map.

Pinch In/Out

Open or close your fingers on the screen in a pinching motion to zoom in or out of the map.

Quick Reference Guide

On input search screens, the suggested search terms are displayed. Select to display a list of possible entries.

How to Enter Information

You can enter information (e.g., city names, street names, numbers, and symbols) when prompted on the input screen.

Using Voice Commands

When you see in this manual, voice commands are available for that feature.

The system recognizes only certain commands. Available navigation commands (P138)

 Press the (Talk) button, and say the letter, number, or symbol

(e.g., say “1”).

 If a voice command is not recognized, a list is displayed with

possible options.

On list screens:

 Say the number of the list item (e.g., say “Three” to select

item 3).

 Say “Main menu” to return to the voice command menu

screen.

 Say “Back” to return to the previous screen.

 Say “Page Up” to scroll up one page.

 Say “Page Down” to scroll down one page.

 Say “Exit” to end the voice command function.

Using the Touchscreen

Select a character or icon on the screen to select it.

 Select to remove the last entered character.

 Select to remove all entered characters.

 Select to display upper/lower case characters.

 Select to enter a space character.

 Select to display other types of characters.

 Select to change the keypad language.

Quick Reference Guide

Map Screen Legend

Map operation icons

(P81)

Map menu (P82 )

Map scale (P81)

Current vehicle position

Streets

Landmark icons

Traffic incident icons

Traffic flow indicator

Traffic is flowing normally.

Traffic is slightly congested.

Traffic is heavily congested or stopped.

Searching specific category (P54)

Traffic has not updated.

Map buttons (P33)

Feature areas

The color of the map is different depending on the selected Map Theme.

Quick Reference Guide

Dashboards (P77)

Next guidance indicator (P77)

Distance to the next guidance point and street name of next guidance point.

Where To? (P54 )

Waypoint

Calculated route

Speed limit

Cancel route

Street name of next guidance point

Distance to next guidance pointEstimated time to

next guidance point

Scrolls key

Select this key to scroll the display.

Day Mode Night Mode

Remaining distance

Street name of next guidance point

Next driving maneuver is ap

proaching.

During Route Guidance

During route guidance, route information is displayed on the map screen. You can see the detailed information on the turn information screen.

Map Screen

Guidance Screen

Day or Night Mode

Press the (Display Mode) icon to manually switch between Day and Night modes.

Turn-by-Turn Directions

The next guidance point appears on the Multi-Information Display (MID).

Quick Reference Guide

Navigation—Home Addresses and Going Home

The “Home” feature automatically routes you to your home address from any location simply by selecting Go Home. You can store one home address. (P18) The order of the steps may change depending on the map data loaded on your system.

Storing Your Home Address

a Select . b Select .

c Press the (Menu) icon and then

select Set Home Location.

d Select Enter My Address.

e Select Search All.

f Enter a house number and then select

Done.

g Enter a street and then select Done.

h Select a street from the list.

If the select city screen is displayed, select a city.

i Select an address from the list. j Select Select.

Going Home

a Select . b Select .

c Select Go Home.

Alternatively, you can say “Navigation” and then “Go Home” from any screen.

Quick Reference Guide

Navigation—Entering a Destination

Enter your destination using one of several methods, then follow route guidance on the map to your destination. The order of the steps may change depending on the map data loaded on your system.

a Select . b Select .

c Select Address.

d Select Search All.

e Enter the house number and select

Done if necessary.

f Enter the name of your destination

street and select Done.

g Select your destination street from

the list.

If the select city screen is displayed, select a city.

h Select an address from the list.

i Select Go!.

Route guidance to the destination begins.

 Routes: Choose one of multiple routes.

 : Display your destination map and

save a place.

Quick Reference Guide

Navigation—Changing Route or Destination

You can alter your route by adding waypoints to visit, or changing your destination during route guidance.

Adding a Waypoint (“Pit Stop”)

You can add waypoints along your route.

(P93)

a Select . b Select . c Select a search method. d Select the location to add to the

destination list and select Go!.

e Select Add to Active Route.

f If necessary, edit the order of the

destinations and select Done.

Changing Your Destination

There are several methods you can use to specify a new destination during route guidance.

 Searching nearby hospitals, police

stations, or gas stations (P95) Select the vehicle icon and select an option.

 Selecting an icon on the map (P94)

Select a place/landmark icon or a new area on the map twice.

 Entering a new destination (P97)

Select Where to? and then enter a new destination.

Canceling Your Route

a Select .

Alternatively, you can say “Navigation” and then “Stop route” from any screen.

Help

This navigation system comes with help information, which tells you how to use this navigation. (P117)

a Select . b Press the (Back) icon.

c Select Apps. d Select Help.

e Select a help topic.

Select to search help topics by keyword.

 You can also display a help topic to

select on each menu screen.

Quick Reference Guide

Voice Control Operation

Voice Portal Screen

a Press and release the (Talk)

button. The system prompts you to say a voice command. Press and release the

(Talk) button again to bypass this prompt.

 The system beeps when ready for a

command. Press the (Hang-Up/ Back) button or the (Back) icon to cancel.

b Say “Navigation.”

The Voice Command screen is displayed. After that follow the voice prompt and say a voice command.

 The audio system is muted during voice

control mode.

 You can use other voice commands on

the Voice Portal screen.

 Set Voice Prompts to Off to bypass the

voice prompt. See the Owner's Manual.

 Carefully read the usage note for the

voice control. Voice Control System (P17)

 You can use other voice commands on

the Voice command screen.

Voice Commands (P138)

Voice Command Screen

a After saying “Navigation” from

the Voice Portal screen, the below screen appears.

b Listen for the voice prompt, then say a

voice command.

 You do not need to press the (Talk)

button again in the Navigation screen.

 Available voice commands are

highlighted on the screen.

Quick Reference Guide

Troubleshooting

For more Information (P123)

Why does the vehicle position icon on the map appear slightly off my actual position, especially at intersections?

This is normal. The navigation system is unaware of the width of intersections. Large differences in vehicle position can indicate a temporary loss of the GPS signal.

Why does the “Arrival time” display sometimes increase even though I am getting closer to my destination?

The “Arrival time” is based on the speed limit on each road. Depending on the traffic conditions, the “arrival time” may be calculated to be earlier or later.

Why does my clock frequently change the time forward and backward by one hour?

The clock setting is automatically updated based on your GPS location. If you are driving near a time zone border, the automatic update is the likely reason.

How do I turn on the navigation system voice guidance?

1.Press the (Home) icon.

Select Settings > System > Sound/Beep tab. Turn up Guidance Volume, if guidance volume is low.

2.Select and then press the (Back) icon.

Select Settings > Navigation. Check that Voice Prompts is not set to off. For more details, see the Owner’s Manual.

How do I specify a destination when an entered city or street could not be found?

Try selecting the destination directly from the map.

How to Use This Manual

Searching the Table of Contents

(P1)

First, find the general chapter related to what you are looking for (e.g., entering a destination from the Saved Places). Then, go to that chapter to view a more specific table of contents.

Searching the Index (P14 1)

This more detailed table of contents shows you exactly what information is listed by section and title.

The Index consists of main terms and subentries. The sub-entries help you get to the desired page depending on what you are looking for.

Table of Contents

Chapter Contents

Navigation Screen

Index

Two types of Tables of Contents help you find your desired information.

Menu items displayed on the navigation screen (e.g., Saved) can be found individually in the Index.

More Detailed

Contents

Go to the

This section explains different methods on how you can easily find information in this manual.

Select the item on the system control panel.

Menu Tree

The menu tree helps guide you through the system’s menu options. To get to your desired function, follow the menu tree in order of the steps shown.

Select the menu option.

After following the menu tree, step-by-step instructions explain how to achieve the desired result.

* Sample pages and images in this section may differ from the actual ones.

Select Saved.

(Home)

Saved

System Setup

This section describes the start-up procedure and the navigation and setup functions.

Start-up ................................................... 16

Voice Control System ............................. 17

Voice Recognition .................................. 17

Personal Information.............................. 18

Setting Home Location........................... 18

Saved Locations ..................................... 19

Display Mode Settings ........................... 26

Switching Display Mode Manually .......... 26

Map & Vehicle......................................... 28

Vehicle................................................... 29

Driving Map View (Map Orientation)...... 30

Map Detail............................................. 31

Map Theme ........................................... 32

Map Buttons.......................................... 33

Map Layers .............................................34

Dashboards.............................................34

myMaps..................................................35

Navigation................................................36

Calculation Mode ...................................37

Avoidances .............................................38

Custom Avoidances ................................39

Traffic .......................................................45

Other Settings..........................................46

Units.......................................................46

Language & Keyboard.............................47

Device.....................................................50

Data Reset ............................................... 52

Reset Factory Default Settings ................ 52

System Setup

Start-up

1 Start-up

Avoid focusing on the screen and drive safely.

When you use the navigation system, the system may close other apps.

When you select Navigation, the system displays the navigation feature that was used the last time. At start-up, the navigation top screen is displayed.

The navigation system starts automatically when you set the power mode to ACCESSORY or ON. At start-up, the following confirmation screen is displayed.

Limitations for Manual Operation

■

Certain manual functions are disabled or inoperable while the vehicle is in motion. You cannot select a grayed-out option until the vehicle is stopped. Voice commands are still operable while the vehicle is in motion.

1. Select OK.

u The HOME screen is displayed. u If you do not select OK, the

system will automatically select OK after a certain period of time.

u The system will automatically

start up the feature that was used the last time.

2. Select .

u The map screen is displayed. u When you want to display the

navigation top screen, you press the (Back) icon.

System Setup

Voice Control System

1 Voice Control System

When you press the (Talk) button, the system prompts you to say a voice command. Press and release the (Talk) button again to bypass this prompt and give a command.

1 Voice Recognition

The voice control system can only be used from the driver’s seat because the microphone unit removes noises from the front passenger’s side.

Your vehicle has a voice control system that allows hands-free operation of the navigation system functions. The voice control system uses the (Talk) and (Hang-Up/Back) buttons on the steering wheel and a microphone near the map lights on the ceiling. For details of the (Talk) button, (Hang-Up/Back) button and microphone position, see the Owner's Manual.

Voice Recognition

To achieve optimum voice recognition when using the navigation voice control system:

• Make sure the correct screen is displayed for the voice command that you are using. The system recognizes only certain commands. Available navigation commands:

2 Navigation Commands P. 138

• Close the windows and moonroof.

• Adjust the dashboard and side vents so air does not blow onto the microphone on the ceiling.

• Speak in a clear, natural speaking voice without pausing between words.

• Reduce any background noise if possible. The system may misinterpret your command if more than one person is speaking at the same time.

System Setup

Personal Information

1 Personal Information

You can also display the same screen by selecting on the Where To? screen.

If you want to delete a shortcut(s), select Remove Shortcut(s).

2 Deleting Shortcuts P. 59

The home location can be overwritten.

Setting Home Location

H uu (Menu)

Use the personal information menu to set your home location.

The following options are available:

• Enter My Address: Sets the home location by entering the address.

2 Storing Your Home Address P. 8

• Use Current Location: Sets your current location as your home location.

• Recently Found: Sets the home location from a recently found location.

1. Select Set Home Location.

2. Select an option.

u Select Use Current Location

to set home location.

u Select Enter My Address or

Recently Found, proceed to

steps 3 and 4.

3. Select the home location.

4. Select Select.

System Setup

Saved Locations

You can save locations so you can quickly find them and create routes to them.

■

H u

uuPersonal InformationuSaved Locations

Saving a Saved Location

1. Select a search method.

u Find a location that you want to

save.

2 Entering a Destination P. 54

2. Select .

3. Press the (Menu) icon or select

4. Select Save.

u If necessary, enter a name and

select Done.

5. Select OK.

Continued

uuPersonal Information u Saved Locations

System Setup

Saving a Saved Location Manually

■

H u (Back) u View Map

1. Select a destination from the map.

2 Map Input P. 73

2. Select the destination name at the

bottom of the map.

3. Press the (Menu) icon or select .

4. Select Save.

u On some places other than POI,

you can edit the place name.

5. Select OK.

System Setup

Saving Your Current Location

1 Saving Your Current Location

Vehicle position may not be displayed when:

• The vehicle is traveling off-road.

• The vehicle position data cannot be updated.

■

H u (Back) u View Map

uuPersonal InformationuSaved Locations

1. Select the vehicle icon.

2. Select Save.

3. Enter a name of the location.

4. Select Done.

5. Select OK.

Continued

uuPersonal Information u Saved Locations

System Setup

Editing a Saved Location

■

H uuSaved

1. Select a saved location you want

to edit.

2. Select .

3. Press the (Menu) icon or select

4. Select Edit.

System Setup

The following options are available:

• Name: Enters a new name for the location.

• Phone Number: Enters a phone number.

• Categories: Creates or changes the category in which this location is saved.

• Change Map Symbol: Select a new symbol.

uuPersonal InformationuSaved Locations

5. Select an option.

Continued

uuPersonal Information u Saved Locations

System Setup

Deleting a Saved Location

■

H uuSaved

1. Select a saved location you want

to delete.

2. Select .

3. Press the (Menu) icon or select

4. Select Delete.

5. Select Yes.

System Setup

■

H uuSaved

uuPersonal InformationuSaved Locations

Deleting Saved Locations

1. Press the (Menu) icon or select .

2. Select Delete Saved Places.

3. Select a saved location you want

to delete.

u Select Select All to delete all

saved locations.

4. Select Delete.

5. Select Yes.

System Setup

Display Mode Settings

1 Switching Display Mode Manually

You can also adjust the display brightness by sliding or swiping on the Brightness bar.

You can change the touchscreen sensitivity setting.

2 Refer to the Owners Manual.

Switching Display Mode Manually

Set the screen brightness separately for Day and Night modes. Press the (Display Mode) icon to cycle through the display modes (Day to Night to Off).

Press the (Display Mode) icon.

u The Brightness bar is displayed for

a few seconds.

u Select or to adjust the

brightness.

System Setup

Illumination control Operation

(Display Mode) icon Selects Day or Night display mode when the user

wants to change the brightness of the display temporarily. Remember: This icon overrides all other display brightness adjustments either set automatically by the sunlight sensor or manually from the System settings screen.

Sunlight sensor (see your Owner’s Manual for location)

If the sunlight sensor detects daylight and the headlights are turned on, the system automatically overrides the Night display and displays the Day display mode. Remember: If desired, use the (Display Mode) icon to override this automatic choice.

Dash illumination adjustment buttons (see your Owner’s Manual for location)

When the headlights are turned on, and you wish to have the Day display mode, adjust the illumination to the full brightness (beeps). Remember: Adjust the dash brightness back to midrange to allow auto switching by sensing the headlights are on or off.

Headlights (Auto/On/Off) When turned on, the display changes to Night

display mode. The previous three controls listed above can “cancel” this function. Remember: Use the (Display Mode) icon to adjust the brightness of the display.

uuDisplay Mode Settingsu Switching Display Mode Manually

System Setup

Map & Vehicle

H u (Back) u Settings u Map & Vehicle

Change the map settings.

The following options are available:

• Vehicle: Changes the icon to represent your position on the map.

2 Vehicle P. 29

• Driving Map View: Sets the perspective on the map.

2 Driving Map View (Map Orientation) P. 30

• Map Detail: Sets the level of detail on the map. More detail may cause the map to draw slower.

2 Map Detail P. 31

• Map Theme: Changes the color of the map data.

2 Map Theme P. 32

• Map Buttons: Sets which icons are included on the map. Up to three icons can be included on the map.

2 Map Buttons P. 33

• Map Layers: Sets the data that appears on the map.

2 Map Layers P. 34

• Dashboards: Sets the map dashboard layout.

2 Dashboards P. 34

Select an option.

System Setup

• myMaps: Sets which installed maps the system uses.

1 Vehicle

The factory default is set to .

2 myMaps P. 35

uuMap & Vehicleu Vehicle

Vehicle

H u (Back) u Settings u Map & Vehicle u Vehicle

You can choose your vehicle icon.

1. Select an option.

2. Select Save.

uuMap & Vehicleu Driving Map View (Map Orientation)

System Setup

Driving Map View (Map Orientation)

H u (Back) u Settings u Map & Vehicle u Driving Map View

Select the map orientation.

The following options are available:

• Track Up: Displays the map with your direction of travel facing upwards.

• North Up: Displays the map with north always pointing up.

• 3-D (factory default): Displays the map in 3D with your direction of travel facing upwards.

1. Select an option.

2. Select Save.

System Setup

Map Detail

H u (Back) u Settings u Map & Vehicle u Map Detail

uuMap & Vehicle u Map Detail

Sets the level of detail on the map.

The following options are available:

• More: Shows more detail on the map.

• Normal (factory default): Shows a standard amount of detail on the map.

• Less: Shows less detail on the map.

1. Select an option.

2. Select Save.

uuMap & Vehicleu Map Theme

System Setup

Map Theme

H u (Back) u Settings u Map & Vehicle u Map Theme

Changes the color of the map data.

1. Select an option.

2. Select Save.

System Setup

Map Buttons

1 Map Buttons

Reset to Defaults

Resets the settings to the factory defaults.

H u (Back) u Settings u Map & Vehicle u Map Buttons

uuMap & Vehicleu Map Buttons

Sets up to three shortcuts that appear in the map tools menu.

1. Select if you want to delete a shortcut and then select OK.

2. Select to add a new shortcut.

3. Select an option.

4. Select Save.

uuMap & Vehicleu Map Layers

System Setup

1 Map Layers

Trip Log is set to off as factory default.

Map Layers

H u (Back) u Settings u Map & Vehicle u Map Layers

Sets the data that appears on the map screen.

1. Select an option(s).

2. Select Save.

Dashboards

H u (Back) u Settings u Map & Vehicle u Dashboards

Switches the dashboard layout at the bottom of the map.

1. Select or .

2. Select Save.

System Setup

myMaps

H u (Back) u Settings u Map & Vehicle u myMaps

uuMap & Vehicle umyMaps

Sets which installed maps the system uses.

Select an option(s).

System Setup

Navigation

1 Navigation

Advanced Detours and GPS Simulator are set to off as factory default.

H u (Back) u Settings u Navigation

Changes the navigation settings.

The following options are available:

• Calculation Mode: Sets route preference.

2 Calculation Mode P. 37

• Avoidances: Sets road features to avoid on a route.

2 Avoidances P. 38

• Custom Avoidances: Allows you to avoid specific roads or areas.

2 Custom Avoidances P. 39

• Advanced Detours: Sets the length of the detour.

• Voice Prompts: Turns the voice prompts on or off.

• GPS Simulator: Stops the system from receiving a GPS signal.

System Setup

Calculation Mode

H u (Back) u Settings u Navigation u Calculation Mode

uuNavigationu Calculation Mode

Sets the route preference.

The following options are available:

• Faster Time (factory default): Calculates routes that are faster to drive but can be

• Shorter Distance: Calculates routes that are shorter in distance but can take

• Less Fuel: Calculates routes that could use less fuel than other routes.

1. Select an option.

2. Select Save.

longer in distance.

more time to drive.

uuNavigationu Avoidances

System Setup

1 Avoidances

Highways, Tolls and Fees, and Ferries are set to off as factory default.

Avoidances

H u (Back) u Settings u Navigation u Avoidances

Set preferences for route options to avoid.

The following options are available:

• U-Turns: Avoids u-turns.

• Highways: Avoids highways.

• Tolls and Fees: Avoids toll roads.

• Ferries: Avoids ferries.

• Carpool Lanes: Avoids car share lanes.

• Unpaved Roads: Avoids unpaved roads.

1. Select an option(s).

2. Select Save.

System Setup

Custom Avoidances

H u (Back) u Settings u Navigation u Custom Avoidances

uuNavigationu Custom Avoidances

Allows you to avoid specific areas and sections of road. You can enable and disable custom avoidances as needed.

The following options are available:

• Add Avoid Area: Sets an area to avoid.

• Add Avoid Road: Sets a road to avoid.

Select an option.

u Select Add Avoidance if custom

avoidances are already stored.

2 Adding an Avoid Area P. 40

2 Adding an Avoid Road P. 41

Continued

uuNavigationu Custom Avoidances

System Setup

Adding an Avoid Area

■

H u (Back) u Settings u Navigation u Custom Avoidances

u Add Avoid Area

1. Select the upper-left (right) corner of the area to avoid. Select Next.

u The icon is displayed on the

map.

2. Select the lower-right (left) corner of the area to avoid. Select Next.

u The selected area is shaded on

the map.

System Setup

■

H u (Back) u Settings u Navigation u Custom Avoidances

uuNavigationu Custom Avoidances

3. Select Done.

Adding an Avoid Road

u Add Avoid Road

1. Select the starting point of the section of road to avoid. Select Next.

u The icon is displayed on the

map.

Continued

uuNavigationu Custom Avoidances

System Setup

2. Select the ending point of the road section. Select Next.

u The selected road color

changes

3. Select Done.

System Setup

■

H u (Back) u Settings u Navigation u Custom Avoidances

The following items are available:

• Rename: Enters a new name.

• Delete: Deletes a selected area or road.

• Disable: Disables the avoidance.

uuNavigationu Custom Avoidances

Editing a Custom Avoidance

1. Select the area or road to edit from the list.

2. Select .

u The menu screen is displayed.

3. Select an item.

Continued

uuNavigationu Custom Avoidances

System Setup

1 Deleting Custom Avoidances

Select if you want to search the saved custom avoidance.

Deleting Custom Avoidances

■

H u (Back) u Settings u Navigation u Custom Avoidances

1. Select .

2. Select options you want to delete.

u Select Select All for all options

in the list.

3. Select Delete.

System Setup

Traffic

H u (Back) u Settings u Traffic

Sets the traffic feature.

The following options are available:

• Traffic: Enables the traffic feature.

• Current Provider: Sets the traffic provider to use for traffic data.

• Subscriptions: Displays the lists of the current traffic subscriptions.

• Optimize Route: Sets whether to use optimized alternate routes On Request

Select an option.

2 Traffic Information P. 86

(factory default) or Automatic.

System Setup

Other Settings

Units

H u (Back) u Settings u Units u Units

Set the units and display on the map of the navigation system.

The following options are available:

• Miles (factory default): Sets the units to miles.

• Kilometers: Sets the units to kilometers.

1. Select an option.

2. Select Save.

System Setup

Language & Keyboard

1 Language & Keyboard

When you select a language for the audio system, the language setting of the navigation system is automatically switched. See the Owner’s Manual for instructions.

H u (Back) u Settings u Language & Keyboard

uuOther SettingsuLanguage & Keyboard

Set the language for the unit and the keyboard layout.

The following options are available:

• Voice Language: Sets the language for voice prompts.

2 Voice Language P. 48

• Keyboard Language: Sets the language for your keyboard.

2 Keyboard Language P. 48

• Keyboard Layout: Sets the keyboard layout.

2 Keyboard Layout P. 49

Select an option.

Continued

uuOther Settings uLanguage & Keyboard

System Setup

Voice Language

■

H u (Back) u Settings u Language & Keyboard u Voice

Language

1. Select an option.

2. Select Save.

Keyboard Language

■

H u (Back) u Settings u Language & Keyboard u Keyboard

Language

1. Select an option.

2. Select Save.

System Setup

■

H u (Back) u Settings u Language & Keyboard u Keyboard

The following options are available:

• QWERTY (factory default): Sets the keyboard layout to QWERTY.

• ABCDE: Sets the keyboard layout to ABCDE.

uuOther SettingsuLanguage & Keyboard

Keyboard Layout

Layout

1. Select an option.

2. Select Save.

uuOther Settings uDevice

System Setup

Device

H u (Back) u Settings u Device

Select an option.

The following options are available:

• About: Displays the device information.

2 About P. 51

• Travel History: Allows the system to record information for suggested routes, previous routes and destinations, and Trip Log features.

• Clear Travel History: Deletes the recorded information.

• Update Map: Displays the description screen of map update.

2 Obtaining a Navigation Update P. 132

System Setup

■

H u (Back) u Settings u Device u About

Displays the device information.

uuOther SettingsuDevice

About

System Setup

Data Reset

1 Reset Factory Default Settings

When you want to reset the following options, see the below references:

• Home

2 Deleting Saved Locations P. 25

• Recent

2 Recent P. 72

• Saved

2 Saved Locations P. 19

When you press the (Menu) icon or select in each settings category, you can restore the selected category.

When you transfer the vehicle to a third party, reset all settings to default and delete all personal data.

Reset Factory Default Settings

H u (Back) u Settings u (Menu)

You can restore all settings to the factory default values.

1. Select Restore.

2. Select Yes.

Navigation

This section describes how to enter a destination, select a route to take, and follow the

route to your destination. It also describes how to change your route or destination along

the way.

Entering a Destination ............................54

HONDA ..................................................60

Address ..................................................61

Categories ..............................................66

Saved......................................................72

Recent ....................................................72

Map Input...............................................73

Calculating the Route ..............................74

Viewing and Selecting the Routes ...........75

Viewing the Destination Map..................76

Driving to Your Destination ...................77

Viewing the Route ..................................77

Map Operation ........................................81

Map Menu..............................................82

Traffic Information ..............................86

Changing Your Route............................. 91

Stopping the Route ................................ 91

Taking a Detour ..................................... 92

Adding Waypoints ................................. 93

Changing Your Destination ................... 94

Selecting a Destination on the Map ........ 94

Searching Near Establishment ................ 95

Entering a New Destination.................... 97

Entering a New Destination from Trip

Planner................................................. 98

Editing the Destination List ................... 102

Navigation

Entering a Destination

1 Entering a Destination

The Display Audio system can only provide route guidance from one navigation system at a time. When setting a destination on one system, any active route guidance with the other system is canceled, and the system you are currently using will direct you to your destination.

To use HondaLink®, you must connect your smartphone to the system. For more details about smartphone connection and how to use HondaLink®, see the Owner's Manual.

Shortcuts

H u

This section describes how to enter a destination for route guidance.

The following options are available:

• Enter Search: Sets a destination by entering a category, name, address, or city name.

2 Using the Search Bar P. 56

• Searching near: Selects the city to search near.

2 Changing the Search Area P. 57

• Go Home: Sets your home address as the destination.

2 Going Home P. 8

• HONDA: Sets a nearby Honda authorized dealer as the destination.

2 HONDA P. 60

• Places: Launches HondaLink® to search for places. For more details, see the Owner's Manual.

• Address: Sets a destination by entering an address.

2 Address P. 61

• Categories: Sets a destination by selecting a category.

2 Categories P. 66

Select an option.

uuEntering a Destinationu

Navigation

• Saved: Sets a destination by selecting a place stored in the Saved list.

2 Saved P. 72

• Recent: Sets a destination by selecting a previous destination.

2 Recent P. 72

• Add Shortcut: Adds shortcuts to the Where To? menu.

2 Adding Shortcuts P. 58

Continued

uuEntering a Destination u

Navigation

1 Using the Search Bar

Using Voice Command

You can say the names of popular, well-known locations. From the Voice Portal screen, say “Navigation.” Say “Find Place,” then say a place name (e.g.,

“Honda”). Say the line number of screen (e.g., “1”). Say “Navigate” or “Yes” to set the route.

2 Using Voice Commands P. 5 2 Voice Control Operation P. 11

• To search for a type of business, enter a category

name, such as “movie theaters.”

• To search for a business by name, enter all or part

of the name.

• To search for an address near you, enter the street

number and street name.

• To search for an address in another city, enter the

street number, street name, city, and state.

• To search for a city, enter the city and state.

If you want to delete the search history, select Restore in the settings menu.

2 Reset Factory Default Settings P. 52

Using the Search Bar

■

H uuEnter Search

You can use the search bar to search for locations by entering a category, name, address, company phone number, or city name.

1. Enter a search term.

u The search history is displayed

below the search bar.

u Suggested search terms appear

below the search bar as you type.

2. Select or a suggested search term.

3. Select your destination from the list.

4. Select Go! to set the route to your destination.

2 Calculating the Route P. 74

Navigation

Changing the Search Area

1 Changing the Search Area

My Active Route and My Destination can be set when the route is active.

■

H uuSearching near

By default, your system finds locations closest to your current location. You can find a location near another city or location.

The following options are available:

• Where I Am Now: Searches near your current location.

• My Active Route: Searches along your current route.

• My Destination: Searches near your current destination.

• A Different City: Searches near the city you enter.

• Recent Destination: Searches near a recent destination.

• Saved Place: Searches near a saved place.

uuEntering a Destinationu

Select an option.

Continued

uuEntering a Destination u

Navigation

Adding Shortcuts

■

H uuAdd Shortcut

Up to 36 shortcut icons can be stored.

Select an option you want to add as a shortcut.

uuEntering a Destinationu

Navigation

Deleting Shortcuts

■

H uu (Menu) u Remove Shortcut(s)

1. Select a shortcut with if you

want to delete it.

2. Select Touch to Remove.

3. Select Save.

uuEntering a Destination uHONDA

Navigation

HONDA

H uuHONDA

Find any Honda authorized dealer to set as a destination.

1. Select the desired name from the list.

2. Select Go! to set the route to your destination.

2 Calculating the Route P. 74

Navigation

Address

1 Address

Using Voice Command

You can say the entire address at once using voice commands. From the Voice Portal screen, say “Navigation.” Say “Find Address” on the voice command screen, then say the entire address. (e.g., “1-2-3-4 Main Street, Los Angeles, California”). Say “Change Country” if you want to change the country. The system interprets the address. Say “Yes” or a line number of a screen if the destination list appears (e.g., “1”). Say “Navigate” or “Yes” to set the route.

2 Using Voice Commands P. 5 2 Voice Control Operation P. 11

H uuAddress

Enter an address to use as the destination. The state or country you are currently in is displayed.

The following options are available:

• Spell City: Selects your destination city.

2 Selecting the City P. 64

• Enter Postal Code: Selects your destination postal code.

2 Selecting the Postal Code P. 65

• Search All: Sets an address to use as the destination.

2 Search All P. 63

• State or Country: Selects the state or country.

2 Selecting the State/Country P. 62

uuEntering a Destination uAddress

Select an option.

Continued

uuEntering a Destination uAddress

Navigation

Selecting the State/Country

■

H uuAddress u State or Country

1. Enter a state or country name.

2. Select a state or country from the

list.

Navigation

Search All

1 Search All

The order of the steps may change depending on the map data loaded on your system.

■

H uuAddress u Search All

uuEntering a Destination uAddress

1. Enter the house number. Select

Done.

2. Enter the street name. Select

Done.

u A list of matching hits is

automatically displayed after you enter several letters, with the closest match at the top of the list.

3. Select your destination from the list.

u If the select city screen is

displayed, select a city.

4. Select Go! to set the route to your destination.

2 Calculating the Route P. 74

Continued

uuEntering a Destination uAddress

Navigation

1 Selecting the City

You do not need to enter spaces or symbols (e.g., &,

-, %).

The order of the steps may change depending on the map data loaded on your system.

Selecting the City

■

H uuAddress u Spell City

1. Enter the name of a different city. Select Done.

u A list of matching hits is

automatically displayed after you enter several letters, with the closest match at the top of the list.

2. Select your destination city from the list.

u Next, you are prompted to

enter a house number.

2 Search All P. 63

uuEntering a Destination uAddress

Navigation

1 Selecting the Postal Code

The order of the steps may change depending on the map data loaded on your system.

Selecting the Postal Code

■

H uuAddress u Enter Postal Code

1. Enter the postal code. Select

Done.

2. Select your destination postal code from the list.

3. Enter the house number. Select Done.

4. Enter the street name. Select Done.

5. Select your destination street from the list.

2 Calculating the Route P. 74

uuEntering a Destination uCategories

Navigation

1 Categories

This option is convenient if you do not know the exact name of a place or if you want to narrow down the number of matches returned for places with a common name.

When you set the destination or waypoint, the same categories of icons do not appear.

Using Voice Command

You can find a place by the name using voice commands. From the Voice Portal screen, say “Navigation. Say “Find Category” on the voice command screen, then say a category (e.g., “Fast Food”). Say “View Categories” if you want to confirm the category list. Say a subcategory if the subcategory screen is displayed. Say a line number of a screen (e.g., “1”). Say “Navigate” or “Yes” to set the route.

2 Using Voice Commands P. 5 2 Voice Control Operation P. 11

Categories

Select the category of a place (e.g., Restaurants, Gas Stations, Shopping) stored in the map database to search for the destination.

Finding a Location by Category

■

H uuCategories

1. Select a category.

2. Select a subcategory.

u If the subcategory screen is not

displayed, proceed to step 3.

Navigation

1 Categories

Quick Search screen

After you have performed a search for a destination, certain categories display a Quick Search list that display several destinations you selected.

uuEntering a Destination u Categories

3. Select a place name from the list.

4. Select Go! to set the route to your

destination.

2 Calculating the Route P. 74

Continued

uuEntering a Destination uCategories

Navigation

1 Finding a Location by Intersections

If there is more than one intersection, you are prompted to select the intersection.

Using Voice Command

You can find intersections by the street name using voice commands. From the Voice Portal screen, say “Navigation.” Say “Find Intersection” on the voice command screen and then say a city name. Say a street name 1, then say a line number of a screen (e.g., “1”). Say a street name 2, then say a line number of a screen (e.g., “1”). Say “Navigate” or “Yes” to set the route.

2 Using Voice Commands P. 5 2 Voice Control Operation P. 11

Finding a Location by Intersections

■

H uuCategories u Intersections

Select the intersection of two streets as the destination.

1. Select Spell City.

u If selecting Search All, proceed

to step 4.

u Select State or Country, if

necessary.

2 Selecting the State/

Country P. 62

2. Enter a city name. Select Done.

u A list of matching hits is

automatically displayed after you enter several letters with the closest match at the top of the list.

3. Select a city.

uuEntering a Destination u Categories

Navigation

4. Enter the street 1 name. Select

Done.

u A list of matching hits is

automatically displayed after you enter several letters with the closest match at the top of the list.

5. Select the street from the list.

u Repeat step 4 to enter the

street 2 name.

6. Select the intersection.

7. Select Go! to set the route to your

destination.

2 Calculating the Route P. 74

Continued

uuEntering a Destination uCategories

Navigation

1 Finding a City

Using Voice Command

You can find a city by using voice commands. From the Voice Portal screen, say “Navigation.” Say “Find City” on the voice command screen, then say a city name. (e.g., “Los Angeles”). Say a line number of a screen (e.g., “1”). Say “Navigate” or “Yes” to set the route.

2 Using Voice Commands P. 5 2 Voice Control Operation P. 11

Finding a City

■

H uuCategories u Cities

Selects your destination city.

1. Select a city.

u Select Enter Search and enter

a city name if you want to narrow down the number of matches.

2. Select Go! to set the route to your destination.

2 Calculating the Route P. 74

uuEntering a Destination u Categories

Navigation

1 Finding a Location Using Coordinates

If you want to change the coordinate format, press the (Menu) icon or select and then select

Format.

Finding a Location Using Coordinates

■

H uuCategories u Coordinates

You can find a location using latitude and longitude coordinates. This can be helpful when geocaching.

1. Select the latitude coordinate.

2. Enter the new coordinate. Select

Done.

3. Select the longitude coordinate.

4. Enter the new coordinate. Select

Done.

5. Select View on Map.

6. Select Go! to set the route to your

destination.

2 Viewing the Destination Map

P. 76

uuEntering a Destination uSaved

Navigation

1 Saved

You can add, edit, or delete the saved place.

2 Saved Locations P. 19

Using Voice Command

You can utilize a saved place by using voice commands. From the Voice Portal screen, say “Navigation.” Say “Saved Place” on the voice command screen, then say a saved place (e.g., “Honda”). Say “View List” if you want to confirm all saved places. Say “Navigate” or “Yes” to set the route.

2 Using Voice Commands P. 5 2 Voice Control Operation P. 11

1 Recent

If you want to delete all recent destinations, press the

(Menu) icon or select and then select Clear.

Using Voice Command

You can utilize a recent destination by using voice commands. From the Voice Portal screen, say “Navigation.” Say “Recently Found” on the voice command screen, then say a line number of a screen (e.g., “1”). Say “Navigate” or “Yes” to set the route.

2 Using Voice Commands P. 5 2 Voice Control Operation P. 11

Saved

H uuSaved

Select a saved location to use as the destination.

Recent

H uuRecent

1. Select your destination from the list.

2. Select Go! to set the route to your destination.

2 Calculating the Route P. 74

Select an address from a list of your 50 most recent destinations to use as the destination. The list is displayed with the most recent destination at the top.

1. Select your destination from the list.

2. Select Go! to set the route to your destination.

2 Calculating the Route P. 74

Navigation

Map Input

1 Map Input

You can customize the map as you like using ,

, , or .

2 Map Operation P. 81

If you want to display a specific category of places, select and then select a category icon.

The place information is displayed when you select

on the map.

2 Viewing the Destination Map P. 76

H u (Back) u View Map

Scroll the map to manually select an icon or a location as the destination.

uuEntering a Destination uMap Input

1. Select any point on the map, a street, intersection, or category icon.

u Return to the current location

when you press the (Back) icon.

2. Select Go! to set the route to your destination.

2 Calculating the Route P. 74

Navigation

Calculating the Route

1 Calculating the Route

If the system has many guidance points on the route to the destination, it may stop calculation. In this case, the route guidance will start when you select OK.

This section describes how to calculate your route.

The following options are available:

• Routes: Displays different routes.

2 Viewing and Selecting the Routes P. 75

• : Display the destination on the map.

2 Viewing the Destination Map P. 76

Select Go!.

u The system calculates and displays

the route line on the map screen.

uuCalculating the RouteuViewing and Selecting the Routes

Navigation

Viewing and Selecting the Routes

View and select different routes to your destination.

1. Select or to change a route.

u The travel distance, estimated

travel time, and traffic information are displayed for each route.

2. Select Go!.

u The system calculates and

displays the route line on the map screen.

uuCalculating the Route uViewing the Destination Map

Navigation

1 Viewing the Destination Map

When you press the (Menu) icon or select , you can add to the saved location list.

2 Saved Locations P. 19

Viewing the Destination Map

The following options are available:

• Route Info: Displays different routes.

2 Viewing and Selecting the Routes P. 75

• Set Location: Sets the vehicle position when you are indoors or not receiving satellite signals. You can use this feature when GPS Simulator is set to on.

2 Navigation P. 36

1. Select an option.

2. Select Go!.

u The system calculates and

displays the route line on the map screen.

Navigation

Driving to Your Destination

1 Viewing the Route

When your phone is connected to Bluetooth® HandsFreeLink®, the navigation screen will switch to the incoming call screen when receiving a call.

Speed limit icon

The speed limit shown on the map may be different from the actual speed limit. The speed limit icon is not displayed on all roads.

Select the vehicle icon to view the Where Am I? screen.

2 Viewing the Current Location Information

P. 84

You can stop your vehicle en route (e.g., to rest, stop for gas, etc.), and then continue on your route.

If you did not complete your route, the navigation restarts when you restart your vehicle.

Next guidance indicator

Speed limit icon

Dashboards

Viewing the Route

This section describes how to follow the route guidance to your destination.

Map Screen

■

The following options are available:

• Select the text bar on the top of the map to display the turn list screen.

2 Turn List P. 78

• Select the next guidance indicator to display the turn information screen or intersection view screen.

2 Turn Information P. 79

• Select to cancel the route guidance and remove your current route.

2 Canceling Your Route P. 10

• Select to display the map menu.

2 Map Menu P. 82

• Select to display the parking information screen of nearby parking.

After calculating the route to your destination, the route is displayed on the map screen.

2 During Route Guidance P. 7

As you drive, the system tracks your position on the map in real time and provides guidance as you approach each guidance point on the route.

Continued

uuDriving to Your Destination u Viewing the Route

Navigation

1 Viewing the Route

The next guidance indicator does not appear in the following cases.

• The vehicle speed is 3 mph (4.8 km/h) or less

• The GPS signal is weak

• The vehicle position on the map and current vehicle

position do not match

The system displays a roundabout to the next guidance indicator in the following cases.

• Its diameter is 82 ft (25 m) or more

• There is no road inside it

• There is no stop sign

Turn-by-Turn Directions

The next guidance point appears on the MultiInformation Display (MID). The Turn-by-Turn directions may not be displayed if the information cannot be received correctly.

• Select the map dashboards when you want to change the information that is displayed. Select the following options:

Arrival Time, Distance, Time to Destination, Via Arrival, Distance to Via, Time to Via, Direction of Travel, Elevation.

Turn List

■

The turn list screen displays turn-by-turn instructions and the distance between turns.

Select the text bar on the top of the map.

u Select a turn to display the

detailed information.

2 Turn Information P. 79

u Press the (Menu) icon or select

to display the entire route on

the map.

2 Entire Route P. 79

Navigation

Turn Information

1 Viewing the Route

Intersection View Screen

The intersection view screen displays a view of the upcoming intersection and which lane you should be driving.

■

The turn information screen displays the turn on the map and the distance and time remaining before you reach the turn. The lane assist screen may display a view of the upcoming intersection.

Entire Route

■

The entire route screen displays the entire route, destination name, time to destination, and distance to destination.

uuDriving to Your Destinationu Viewing the Route

Select the next guidance indicator of the map or select any turn on the turn list screen.

1. Select the text bar on the top of the map.

2. Press the (Menu) icon or select

3. Select Map to display the entire route screen.

u Press the (Back) icon to

return to the previous screen.

Continued

uuDriving to Your Destination u Viewing the Route

Navigation

1 Trip Log Display

You can delete the Trip Log.

2 Device P. 50 2 Reset Factory Default Settings P. 52

Deviating From the Planned Route

■

If you leave the calculated route, the system automatically recalculates a route to the set destination based on your current location and direction.

Trip Log Display

■

If you set the trip log to show, a series of lines (breadcrumbs) are displayed to track the path you are taking.

2 Map Layers P. 34

Navigation

Map Operation

1 Map Operation

When you select Track Up or North Up, the current map scale and the (Track Up only) appear on the map. The always points to North.

2 Driving Map View (Map Orientation) P. 30

Customize the map, set a destination, and save a place from the map.

The following options are available:

• : Zooms in to the map.

• : Zooms out of the map.

• : Switches the map to 2D or 3D.

• : Rotates the 3D map.

• : Sets the data that appears on the map.

2 Map Layers P. 34

1. Select any point on the map.

2. Select an option.

u If you want to set a destination

or save a location in the map, scroll the map and select the desired location.

2 Saved Locations P. 19 2 Map Input P. 73

uuMap OperationuMap Menu

Navigation

1 Map Menu

You can also display the map menu by selecting on the map screen.

Map Menu

H u (Menu)

The following options are available:

• Where To?: Enters a new destination.

2 Entering a Destination P. 54

• Traffic: Displays the traffic information screen.

2 Traffic Information P. 86

• Mute: Turns the voice prompts on or off.

• Stop: Cancels the route guidance and removes your current route.

• Detour: Calculates a detour route.

2 Taking a Detour P. 92

• Exit Services: Displays a list of the exit services for the route.

2 Viewing Exit Services P. 83

• Where Am I?: Displays the information about your current location.

2 Viewing the Current Location Information P. 84

• Map Layers: Sets the data that appears on the map.

2 Map Layers P. 34

• ecoRouteTM: Uses the ecoRouteTM features.

2 ecoRouteTM P. 109

Select an option.

uuMap OperationuMap Menu

Navigation

1 Viewing Exit Services

The map screen of the selected exit is displayed when you select .

• Settings: Change settings for navigation functions.

2 System Setup P. 15

Viewing Exit Services

■

H u (Menu) u Exit Services

You can view exit services (e.g., whether the exit is near gas stations, restaurants, etc.) and add new destinations or waypoints to the calculated route.

1. Select or to display your desired list of exit services.

2. Select a category tab.

3. Select an option.

u The location is displayed on the

Calculate Route screen.

2 Viewing the Destination Map

P. 76

Continued

uuMap OperationuMap Menu

Navigation

1 Viewing the Current Location Information

Vehicle position may not be displayed when:

• The vehicle is traveling off-road.

• The vehicle position data cannot be updated.

Viewing the Current Location Information

■

H u (Menu) u Where Am I?

You can confirm your current location, address, and nearest intersection.

Select an option.

The following options are available:

• Save: Saves your current location.

2 Saving Your Current Location P. 21

• Hospitals/Police Stations/Fuel: Searches for a hospital, police station, or gas station around your current location.

2 Searching Near Establishment P. 95

uuMap OperationuMap Menu

Navigation

Using Directions to Me

■

H u (Menu) u Where Am I?

Get a list of directions to your current location.

1. Press the (Menu) icon or select .

2. Select Directions to Me.

3. Select an option.

4. Select Select.

u The turn list screen displays

turn-by-turn instructions and the distance between turns.

2 Turn List P. 78

uuMap OperationuTraffic Information

Navigation

1 Traffic Information

You can change the traffic information settings.

2 Traffic P. 45

The traffic icon changes color to indicate the severity of traffic conditions.

• Green: Flowing freely.

• Yellow: Moderate traffic condition.

• Red: Very slow or stop-and-go traffic.

• Gray: No traffic data.

Traffic Information

When you set the traffic feature, the system examines traffic conditions and optimizes the route for the shortest time. If a severe traffic delay occurs while you are navigating, the system searches for a faster route. If it finds one, the system will prompt you and you can choose to accept the new route. The traffic icon changes color to indicate the severity of traffic conditions on your route or on the road you are currently traveling. The system may route you through a traffic delay if a better alternative route does not exist. The delay time is added into your estimated time of arrival automatically.

1. Select on the map screen.

uuMap OperationuTraffic Information

Navigation

2. Select an option.

The following options are available:

• Alternate Route: Display the alternate route screen.

2 Alternate Route P. 88

• Traffic On Route: Displays the traffic delays on your route. You can select the traffic you want to avoid.

2 Traffic Rerouting Manually P. 89

• Traffic Conditions: Display the traffic flow and delays on nearby roads.

2 Viewing Traffic Delays P. 90

• Traffic Legend: Displays an overview of traffic legends.

2 Viewing Traffic Legends P. 90

Continued

uuMap OperationuTraffic Information

Navigation

Alternate Route

■

H uuAlternate Route

Display the alternate route screen.

Select Go!.

uuMap OperationuTraffic Information

Navigation

Traffic Rerouting Manually

■

H uuTraffic On Route

View the traffic delays on your route, including the estimated time of each delay and the distance to each delay. You can select the traffic you want to avoid manually.

1. Display a list of traffic events.

2. Select an option.

3. Select and then select Avoid

to avoid the traffic delay.

u Select or to view other

traffic delays on your route.

Continued

uuMap OperationuTraffic Information

Navigation

Viewing Traffic Delays

■

H uuTraffic Conditions

View the traffic flow and delays on nearby roads.

Viewing Traffic Legends

■

H uuTraffic Legend

See an overview of the icons and colors used on the traffic map.

u Select if you want to display a

list of traffic delays.

The system displays the traffic legend.

Navigation

Changing Your Route

1 Stopping the Route

You can also stop your route from the map menu.

2 Map Menu P. 82

Stopping the Route

Stop the route guidance and remove the destination and all waypoints.

Select .

uuChanging Your RouteuTaking a Detour

Navigation

1 Taking a Detour

If your current route is the only reasonable option, the system might not calculate a detour.

1 Taking a Detour Around Specified Areas

You can use this feature when Advanced Detours is set to On.

2 Navigation P. 36

Select to delete all detours.

Taking a Detour

H u (Menu) u Detour (when en route)

Calculate a new route to avoid something ahead of you. The system creates a new route if possible. The system attempts to get you back on your original route as quickly as possible.

Taking a Detour Around Specified Areas

■

You can take a detour for a specified distance along your route or detour around specific roads. This is useful if you encounter construction zones, closed roads, or poor road conditions.

The following options are available:

• Next 0.5 mi on Route: Calculates a new route by avoiding the next 0.5 mile on your route.

• Next 2 mi on Route: Calculates a new route by avoiding the next 2 miles on your route.

• Next 5 mi on Route: Calculates a new route by avoiding the next 5 miles on your route.

• Detour by Road(s) on Route: Calculates a new route by avoiding the specific roads on your route. Select roads from the turn list.

Select an option.

uuChanging Your Routeu Adding Waypoints

Navigation

1 Adding Waypoints

When you add a waypoint, the system may take some time to update the arrival time.

Adding Waypoints

Add waypoints (pit stops) along the route to your destination.

1. While en route, select a search method to add a new destination or waypoint.

2 Entering a Destination P. 54

2. Select a place. Select Go!.

3. Select Add to Active Route.

u Select Start New Route to set

the location as your new destination.

2 Entering a New Destination

P. 97

4. Select and hold , or and then move the destination to the desired position.

5. Select Done.

u The route is automatically

recalculated and displayed on the map screen.

Navigation

Changing Your Destination

Selecting a Destination on the Map

Select a new destination when en route by selecting a location on the map.

1. Select any point on the map, or a street, intersection, or category icon.

2. Select Go!.

3. Select an option.

The following options are available:

• Start New Route: Sets the location as your new destination.

• Add to Active Route: Sets the location as the first waypoint in the Edit Route screen.

2 Adding Waypoints P. 93

uuChanging Your DestinationuSearching Near Establishment

Navigation

Searching Near Establishment

H u (Menu) u Where Am I?

Search for a hospital, police station, or gas station around your current location.

1. Select a category type.

u You can also confirm your

current location, address, and nearest intersection.

2. Select a place.

3. Select Go!.

Continued

uuChanging Your DestinationuSearching Near Establishment

Navigation

4. Select an option.

The following options are available:

• Start New Route: Sets the location as your new destination.

• Add to Active Route: Sets the location as the first waypoint in the Edit Route screen.

2 Adding Waypoints P. 93

uuChanging Your DestinationuEntering a New Destination

Navigation

1 Entering a New Destination

You can also display the Where To? screen by pressing (Back) icon on the navigation top screen.

Entering a New Destination

H u

Enter a new destination using the destination menu screen even when you are en route.

1. Select a search method to enter a new destination.

2 Entering a Destination P. 54

2. Select a place and then select Go!.

3. Select an option.

The following options are available:

• Start New Route: Sets the location as your new destination.

• Add to Active Route: Sets the location as the first waypoint in the Edit Route screen.

2 Adding Waypoints P. 93

uuChanging Your DestinationuEntering a New Destination from Trip Planner

Navigation

Entering a New Destination from Trip Planner

You can use the trip planner to create and save a route with multiple destinations.

Creating Your Route

■

H u (Back) u Apps u Trip Planner u New Trip u Select Start

Location

1. Select a method to enter a new

destination.

2 Entering a Destination P. 54

2. Select Select.

3. Select to add additional

locations.

u Repeat steps 1 and 2 to enter

the destination.

u Select and hold , or

and then move the destination to the desired position.

u Select to delete unwanted

destinations.

4. Select Next.

Honda Ridgeline (2022) Navigation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

Quick Reference Guide

Overview—Functions at a Glance

HOME Screen

Touchscreen Operation

How to Enter Information

Map Screen Legend

During Route Guidance

Navigation—Home Addresses and Going Home

Navigation—Entering a Destination

Navigation—Changing Route or Destination

Help

Voice Control Operation

Troubleshooting

How to Use This Manual

System Setup

Navigation