2000
-
06 ACCESSORIES & EQUIPMENT
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2006 Honda Insight
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Keyless/Power Door Lock System - Insight
COMPONENT LOCATION INDEX
Fig. 1: Identifying Keyless/Power Door Lock System Component Location
CIRCUIT DIAGRAM
CONTROL UNIT INPUT TEST
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Fig. 2: Circuit Diagram - Keyless/Power Door Lock System
Courtesy of AMERICAN HONDA MOTOR CO., INC.
If any test indicates a problem, find and correct the cause, then recheck the
Possible cause if
result is not
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
1. Remove the driver's pocket (see DASHBOARD
REMOVAL/INSTALLATION ).
2. Disconnect the 18P connector (B) from the keyless door lock control unit (A).
Fig. 3: Disconnecting 18P Connector From Keyless Door Lock Control
Unit
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Inspect the connector and socket terminals to be sure they are making good
contact.
If the terminals are bent, loose or corroded, repair them as necessary, and
recheck the system.
If the terminals look OK, go to step 4.
4. With the connector still disconnected, make these input tests at the connector.
system.
If all the input tests prove OK, go to step 5.
CONNECTOR INPUT TEST REFERENCE
Test: Desired
Cavity Wire Test condition
result
ground: Ceiling
Blown No. 19
(7.5 A) fuse in
dash
fuse/relay box
Blown ceiling
light bulb
An open in the
wire
Faulty horn
Faulty horn
relay
An open in the
wire
Blown No. 16
(30 A) fuse in
hood
fuse/relay box
Faulty taillight
relay
An open in the
wire
to the No. 17 terminal
Check door lock
operation: Both
doors and hatch
Faulty actuator
An open in the
wire
terminal to the No. 17
Check door lock
Faulty driver's
door lock
actuator
An open in the
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
2 GRN/RED Under all conditions
3 ORN Under all conditions
Attach to
light should
come on.
Attach to
ground: The
horn should
sound.
obtained
the under-
4 RED/WHT
6 YEL/BLK
7 YEL/GRN
Combination light
switch ON
Connect No. 8
terminal to the No. 6
terminal, and No. 7
and No. 18 terminals
momentarily.
Connect No. 8
terminal to the No. 7
terminal, and No. 6
Check for
voltage to
ground: There
should be
battery voltage.
should lock.
operation:
Driver's door
the under-
terminal
should unlock.
If any test indicates a problem, find and correct the cause, then recheck the
wire
terminal to the No. 18
Check door lock
Faulty
passenger's
door lock
actuator
Faulty hatch
lock actuator
An open in the
wire
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
18 YEL
momentarily.
Connect No. 8
terminal, and No.
6terminal to the No.
17 terminal
momentarily.
operation:
Passenger's
door and hatch
should unlock.
Fig. 4: Identifying Keyless Door Lock 18P Connector Terminals
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Reconnect the 18P connector to the keyless door lock control unit, and make
these input tests at the connector.
Test: Desired
Possible cause if result
ground: There
Poor ground
(G401, G402)
An open in the
wire
ground: There
Blown No. 16 (30
A) fuse in the
hood
fuse/relay box
Blown No. 22 (20
A) fuse in the
dash
fuse/relay box
An open in the
wire
ground: There
Blown No. 6 (7.5
A) fuse in the
dash
fuse/relay box
An open in the
wire
ground: There
Blown No. 16 (30
A) fuse in the
hood
fuse/relay box
Faulty taillight
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
system.
If all the input tests prove OK, the control unit must be faulty; replace the
keyless door lock control unit.
CONNECTOR INPUT TEST REFERENCE
Cavity Wire Test condition
result
is not obtained
Check for
voltage to
Under all
17 BLK
conditions
should be less
than 1 V.
8 WHT
16 YEL
1 BLU
Under all
conditions
Ignition switch
ON (II)
Combination
switch OFF
Check for
voltage to
should be
battery
voltage.
Check for
voltage to
should be
battery
voltage.
Check for
voltage to
under-
under-
under-
under-
should be
battery
relay An open in
the wire
ground: There
Poor ground
(G401, G402)
Faulty driver's door
lock actuator (knob
switch)
An open in the
wire
ground: There
Faulty driver's door
lock actuator (knob
ground: There
Poor ground
(G401, G402,
G601)
Faulty driver's door
lock switch
Faulty hatch key
cylinder switch
An open in the
wire
ground: There
Faulty driver's door
lock switch
Faulty hatch key
cylinder switch
Short to ground in
the wire
Poor ground
(G401, G402,
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
10 YEL/RED
Driver's door
lock knob in
LOCK
Driver's door
lock knob in
UNLOCK
voltage.
Check for
voltage to
should be less
than 1 V.
Check for
voltage to
should be
about 5 V or
more.
switch)
Short to ground in
the wire
11 WHT/GRN
Driver's door
lock switch in
UNLOCK
Hatch key
cylinder switch
in UNLOCK
Driver's door
lock switch in
neutral
Hatch key
cylinder switch
in LOCK
Check for
voltage to
should be less
than 1 V.
Check for
voltage to
should be
about 5 V or
more.
Driver's door
lock switch in
ground: There
G601)
Faulty driver's door
lock switch
Faulty hatch key
cylinder switch
An open in the
wire
ground: There
Faulty driver's door
lock switch Faulty
hatch key cylinder
switch
Short to ground in
the wire
Ignition key is in
ground: There
Poor ground
(G401,G402)
Faulty ignition key
switch
An open in the
wire
ground: There
Faulty ignition key
Door(s) or hatch
ground: There
Poor ground
(G601)
Faulty door switch
Faulty hatch latch
switch
An open in the
wire
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
12 WHT/BLU
LOCK
Hatch key
cylinder switch
in LOCK
Driver's door
lock switch in
neutral
Hatch key
cylinder switch
in UNLOCK
Check for
voltage to
should be less
than 1 V.
Check for
voltage to
should be
about 5 V or
more.
13 BLU/RED
14 LTGRN/RED
the ignition
switch
Ignition key
removed from
the ignition
switch
open
Check for
voltage to
should be less
than 1 V.
Check for
voltage to
should be
about 5 V or
more.
Check for
voltage to
should be less
switch
Short to ground in
the wire
than 1 V.
2.
Disconnect the 2P connector (A) from the actuator (B).
Door(s) or hatch
ground: There
Faulty door switch
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Check for
voltage to
closed
should be
about 5 V or
more.
DRIVER'S DOOR LOCK ACTUATOR TEST
1. Remove the driver's door panel (see DOOR PANEL
REMOVAL/INSTALLATION ).
Faulty hatch latch
switch
Short to ground in
the wire
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Fig. 5: Disconnecting 2P Connector From Actuator
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2.
Disconnect the 3P connector (A) from the actuator (B).
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
3. Check actuator operation by connecting power and ground according to the
table. To prevent damage to the actuator, apply battery voltage only
momentarily.
Fig. 6: Power And Ground Connection Reference Table
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. If the actuator does not operate as specified, replace it.
DRIVER'S DOOR LOCK KNOB SWITCH TEST
1. Remove the driver's door panel (see DOOR PANEL
REMOVAL/INSTALLATION ).
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Fig. 7: Disconnecting 3P Connector From Actuator
2.
Disconnect the 3P connector from the switch.
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
3. Check for continuity between the A1 andA2 terminals.
With the driver's door locked, there should be continuity.
With the driver's door unlocked, there should be no continuity.
4. If the continuity is not as specified, replace the driver's door lock knob switch.
DRIVER'S DOOR LOCK SWITCH TEST
1. Remove the driver's door panel (see DOOR PANEL
REMOVAL/INSTALLATION ).
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Fig. 8: Disconnecting 3P Connector From Switch
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2.
Disconnect the 2P connector (A) from the actuator (B).
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
3. Check for continuity between the terminal in each switch position according to
the table.
Fig. 9: Door Lock Switch Continuity Checking Reference Table
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. If the continuity is not as specified, replace the driver's door lock switch.
PASSENGER'S DOOR LOCK ACTUATOR TEST
1. Remove the passenger's door panel (see DOOR PANEL
REMOVAL/INSTALLATION ).
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Fig. 10: Disconnecting 2P Connector From Actuator
2.
Disconnect the 6P connector (A) from the hatch lock actuator (B).
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
3. Check actuator operation by connecting power and ground according to the
table. To prevent damage to the actuator, apply battery voltage only
momentarily.
Fig. 11: Power And Ground Connection Reference Table
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. If the actuator does not operate as specified, replace the passenger's door lock
actuator.
HATCH LOCK ACTUATOR/LATCH SWITCH/UNLOCK SWITCH TEST
1. Open the hatch and remove the rear trim panel (see TRIM
REMOVAL/INSTALLATION - CARGO AREA ).
3. Check actuator operation by connecting battery power and grounding
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Fig. 12: Disconnecting 6P Connector From Hatch Lock Actuator
Courtesy of AMERICAN HONDA MOTOR CO., INC.
ACTUATOR TEST
according to the table. To prevent damage to the actuator, apply battery voltage
HATCH KEY CYLINDER SWITCH TEST
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
only momentarily.
Fig. 13: Battery Power And Grounding Connection Reference Table
Courtesy of AMERICAN HONDA MOTOR CO., INC.
LATCH SWITCH TEST
4. Check for continuity between terminal No. 1 and terminal No. 2.
With the hatch open, there should be continuity.
With the hatch closed, there should be no continuity.
UNLOCK SWITCH TEST
5. Check for continuity between terminal No. 3 and terminal No. 6.
With the hatch unlocked, there should be continuity.
With the hatch locked, there should be no continuity.
If the tests don't work as specified, replace the hatch latch assembly.
3.
Check for continuity between the terminals in each switch position according
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
1. Open the hatch and remove the rear trim panel (see TRIM
REMOVAL/INSTALLATION - CARGO AREA ).
2. Disconnect the 3P connector (A) from the key cylinder switch (B).
Fig. 14: Disconnecting 3P Connector From Key Cylinder Switch
Courtesy of AMERICAN HONDA MOTOR CO., INC.
If the locks don't work, go to step 2.
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
to the table.
Fig. 15: Key Cylinder Switch Continuity Checking Reference Table
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. If the continuity is not as specified, replace the switch.
TRANSMITTER TEST
NOTE:
If the doors unlock or lock with the transmitter, but the
LED on the transmitter does not come on, the LED is
faulty; replace the transmitter.
If any door is open, you cannot lock the door with the
transmitter.
If you unlocked the doors with the transmitter, but do
not open any of the doors within 30 seconds, the doors
relock automatically.
The doors do not lock or unlock with the transmitter if
the ignition key is inserted in the ignition switch.
1. Press the lock or unlock button five or six times to reset the transmitter.
If the locks work, the transmitter is OK.
If the doors don't lock and unlock, go to step 4.
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
2. Open the transmitter and check for water damage.
If you find any water damage, replace the transmitter.
If there is no water damage, go to step 3.
3. Replace the transmitter battery (A) with a new one, and try to lock and unlock
the doors with the transmitter by pressing the lock or unlock button five or six
times.
If the doors lock and unlock, the transmitter is OK.
4.
Rewrite and register the transmitter code, then try to lock and unlock the doors.
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
Fig. 16: Identifying Transmitter Battery
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Within 10 sec, aim the transmitters (up to three) whose codes you want to store
stored.
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
If the doors lock and unlock, the transmitter is OK.
If the doors don't lock and unlock, replace the transmitter.
TRANSMITTER PROGRAMMING
Storing transmitter codes:
The codes of up to three transmitters can be stored into the keyless receiver unit
memory. (A fourth code cannot be stored.)
NOTE: It is important to maintain the time limits between the steps.
1. Turn the ignition switch ON (II).
2. Within 1 to 4 sec, push the transmitter lock or unlock button with the
transmitter aimed at the receiver (control unit).
3. Within 1 to 4 sec, turn the ignition switch OFF.
4. Within 1 to 4 sec, turn the ignition switch ON (II).
5. Within 1 to 4 sec, push the transmitter lock or unlock button with the
transmitter aimed at the receiver (control unit).
6. Within 1 to 4 sec, turn the ignition switch OFF.
7. Within 4 sec, turn the ignition switch ON (II).
8. Within 1 to 4 sec, push the transmitter lock or unlock button with the
transmitter aimed at the receiver (control unit).
9. Within 1 to 4 sec, turn the ignition switch OFF.
10. Within 4 sec, turn the ignition switch ON (II).
11. Within 1 to 4 sec, push the transmitter lock or unlock button with the
transmitter aimed at the receiver (control unit).
12. Confirm you can hear the sound of the door lock actuators. Within 1 to 4 sec,
push the transmitter lock or unlock button again.
13.
at the receiver, and press the transmitter lock or unlock buttons. Confirm that
you can hear the sound of the door lock actuators after each transmitter code is
15.
Confirm proper operation with the new code(s).
2006 Honda Insight
2000-06 ACCESSORIES & EQUIPMENT Keyless/Power Door Lock System - Insight
14. Turn the ignition switch OFF, and pull out the key.
Loading...