Use these links (and links throughout this manual) to navigate through this reference.
For a printed owner's manual, click on authorized manuals or go to www.helminc.com.
Owner's Identification Form
Introduction ......................................................................................................................................... i
A Few Words About Safety................................................................................................................. ii
Your Car at a Glance ...........................................................................................................................2
Driver and Passenger Safety ..............................................................................................................5
Proper use and care of your car's seat belts, and Supplemental Restraint System.
Instruments and Controls................................................................................................................. 59
Instrument panel indicator and gauge, and how to use dashboard and steering column controls.
Comfort and Convenience Features ..............................................................................................121
How to operate the climate control system, the audio system, and other convenience features.
Before Driving..................................................................................................................................223
What gasoline to use, how to break-in your new car, and how to load luggage and other cargo.
How to order manuals and other technical literature.
Index ..................................................................................................................................................... I
Service Information Summary
A summary of information you need when you pull up to the fuel pump.
Contents
Owner’s Identification
Main Menu
OWNER
ADDRESS
STREET
CITYSTATE/PROVINCEZIP CODE/
V. I. N.
DELIVERY DATE
(Date sold to original retail purchaser)
DEALER NAMEDEALER NO.
ADDRESS
STREET
CITYSTATE/PROVINCEZIP CODE/
OWNER’S SIGNATURE
DEALER’S SIGNATURE
POSTAL CODE
POSTAL CODE
This Owner’s Manual should be considered
a permanent part of the car, and should
remain with the car when it is sold.
This Owner’s Manual covers all models of
the Accord Coupe. You may find
descriptions of equipment and features that
are not on your particular model.
The inf ormation and specifications included
in this publication were in effect at the time
of approval for printing. Honda Motor Co.,
Ltd. reserves the right, however, to
discontinue or change specif ications or
design at any time without notice and
without incurring any obligation whatsoever.
Si prefiere este Manual del
Propietario en español, comuníquese
con el concesionario Honda.
Introduction
Main Menu
Congratulations! Your selection of a 2003 Honda Accord was a wise
investment. It will give you years of driving pleasure.
One of the best ways to enhance the enjoyment of your new Honda is to
read this manual. In it, you will learn how to operate its driving controls and
convenience items. Afterwards, keep this owner’s manual in your car so you
can refer to it at any time.
Several warranties protect your new Honda. Read the warranty booklet
thoroughly so you understand the coverages and are aware of your rights
and responsibilities.
Maintaining your car according to the schedules given in this manual helps
to keep your driving trouble-free while it preserves your investment. When
your car needs maintenance, keep in mind that your Honda dealer’s staff is
specially trained in servicing the many systems unique to your Honda. Your
Honda dealer is dedicated to your satisfaction and will be pleased to answer
any questions and concerns.
California Proposition 65 Warning
WARNING:
California to cause cancer and birth def ects or other reproductive harm.
This product contains or emits chemicals known to the State of
As you read this manual, you will
find inf ormation that is preceded by
asymbol. This
information is intended to help you
avoid damage to your Honda, other
property, or the environment.
i
AFewWordsAboutSafety
Main Menu
Your safety, and the safety of others,
is very important. And operating this
car saf ely is an important
responsibility.
To help you make informed
decisions about safety, we have
provided operating procedures and
other information on labels and in
this manual. This information alerts
you to potential hazards that could
hurt you or others.
Of course, it is not practical or
possible to warn you about all the
hazards associated with operating or
maintaining your car. You must use
your own good judgement.
ii
You will f ind this important saf ety inf ormation in a variety of forms,
including:
Safety Labels
Safety Messages
three signal words:,, or.
These signal words mean:
Safety Headings
Safety Precautions.
Safety Section
Instructions
This entire book is filled with important safety informationplease read it
carefully.
−
on the car.
−
preceded by a safety alert symboland one of
DANGER WARNINGCAUTION
You WILL be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
You CAN be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
You CAN be HURT if you don’t follow
instructions.
−
such as Important Safety Reminders or Important
−
such as Driver and Passenger Safety.
−
how to use this car correctly and safely.
−
Your Car at a Glance
Main Menu
MIRROR CONTROLS
(P.108)
POWER DOOR LOCK
MASTER SWITCH
(P.86)
POWER WINDOW
SWITCHES
(P.103)
FUEL FILL DOOR/
TRUNK RELEASE HANDLE
(P.225, 91)
2
INSTRUMENT PANEL (P.61)
HOOD RELEASE
HANDLE
(P.226)
HAZARD WARNING LIGHTS
AUTOMATIC TRANSMISSION
MANUAL TRANSMISSION
(P.79)
AUDIO SYSTEM
DIGITAL CLOCK
HEATING/COOLING
CONTROLS
(P.122)
CLIMATE CONTROL
SYSTEM
(P.129)
(P.243, 245)
(P.148, 163, 187)
(P.153, 171, 193)
(P.248)
Your Car at a Glance
Main Menu
HEADLIGHTS/
TURN SIGNALS
(P.74/77)
REMOTE AUDIO
CONTROLS
(P.211)
MOONROOF SWITCH
(P.107)
VOICE CONTROL SWITCHES
**Only on cars equipped with Navigation System. Refer to the Navigation System Owner’s Manual.:
INSTRUMENT PANEL BRIGHTNESS
(P.76)
TRACTION CONTROL
SYSTEM ON/OFF
SWITCH
(P.259)
WINDSHIELD WIPERS/WASHERS
(P.77, 79)
HORN
(P.73)
TILT/TELESCOPIC
ADJUSTMENT
(P.80)
EX-V6 model without Navigation System is shown.
HAZARD
WARNING
LIGHTS
(P.79)
CRUISE
CONTROL
BUTTONS
(P.214)
REAR WINDOW
DEFOGGER
(P.79)
3
4
Main Menu
Driver and Passenger Saf ety
Main Menu
This section gives you important
information about how to protect
yourself and your passengers. It
shows you how to use seat belts
properly. It explains your Supplemental Restraint System. And it tells
you how to properly restrain infants
andchildreninyourcar.
You’ll find many safety
recommendations throughout this
section, and throughout this manual.
Therecommendationsonthispage
are the ones we consider to be the
most important.
Always Wear Your Seat Belt
A seat belt is your best protection in
all types of collisions. Airbags
supplement seat belts, but airbags
are designed to inflate only in a
moderate to severe frontal collision.
So even though your car is equipped
with airbags, make sure you and
your passengers always wear your
seat belts, and wear them properly.
(See page.)
16
Restrain All Children
Children are safest when they are
properly restrained in the back seat,
notthefrontseat.Achildwhoistoo
smallforaseatbeltmustbeproperly
restrained in a child safety seat. (See
page.)
21
6
Driver and Passenger Saf ety
Be Aware of Airbag HazardsControl Your Speed
While airbags can save lives, they
can cause serious or fatal injuries to
occupants who sit too close to them,
or are not properly restrained.
Infants, young children, and short
adults are at the greatest risk. Be
sure to f ollow all instructions and
warnings in this manual. (See page
.)
9
Excessive speed is a major factor in
crash injuries and deaths. Generally,
the higher the speed the greater the
risk, but serious accidents can also
occur at lower speeds. Never drive
faster than is safe for current
conditions, regardless of the
maximum speed posted.
Keep Your Car in Safe Condition
Don’t Drink and Drive
Alcohol and driving don’t mix. Even
one drink can reduce your ability to
respond to changing conditions, and
your reaction time gets worse with
every additional drink. So don’t drink
and drive, and don’t let your f riends
Having a tire blowout or a
mechanical f ailure can be extremely
hazardous. To reduce the possibility
of such problems, check your tire
pressures and condition frequently,
and perform all regularly scheduled
maintenance. (See page.)
drink and drive, either.
274
(3)(4)
Main Menu
Table of Content
(10)
(8)
(9)
Your Car’s Saf ety Features
Your car is equipped with many
features that work together to
protect you and your passengers
during a crash.
(7)
*
If equipped:
(1)
(2)
(6)
(2)
(7)
(5)
(1) Safety Cage
(2) Crush Zones
(3) Seats and Seat-Backs
(4) Head Restraints
(5) Collapsible Steering Column
(6) Seat Belts
(7) Front Airbags
(8) Side Airbags
(9) Side Curtain Airbags
(10) Door Locks
(11) Seat Belt Tensioners
(11)
*
*
Some safety features do not require
anyactiononyourpart.These
include a strong steel framework
that forms a safety cage around the
passenger compartment; front and
rear crush zones that are designed to
crumple and absorb energy during a
crash; a collapsible steering column;
and seat belt tensioners that
automatically tighten the front seat
belts in the event of a crash.
CONTINUED
Driver and Passenger Saf ety
7
Your Car’s Saf ety Features
Main Menu
Table of Content
These safety features are designed
to reduce the severity of injuries in a
crash. However, you and your
passengers can’t take full advantage
of these safety features unless you
remain sitting in a proper position
always wear your seat belts
and
properly.
In fact, some safety
features can contribute to injuries if
they are not used properly.
8
Driver and Passenger Saf ety
Seat Belts
Foryoursafety,andthesafetyof
your passengers, your car is
equipped with seat belts in all seating
positions.
Your seat belt system also
includes a light on the
instrument panel to remind you and
your passengers to fasten your seat
belts.
Why Wear Seat Belts
Seat belts are the single most
effectivesafetydeviceforadultsand
larger children. (Infants and smaller
children must be properly restrained
in child seats.)
Not wearing a seat belt properly
increases the chance of serious
injury or death in a crash, even
though your car has airbags.
In addition, most states and all
Canadian provinces require you to
wear seat belts.
Not wearing a seat belt properly
increases the chance of serious
injury or death in a crash, even
if you have airbags.
Be sure you and your
passengers always wear seat
belts and wear them properly.
When properly worn, seat belts:
Keep you connected to the vehicle
so you can take advantage of the
vehicle’s built-in safety features.
Help protect you in almost every
type of crash, including frontal,
side, and rear impacts and
rollovers.
Your Car’s Saf ety Features
Main Menu
Table of Content
Help keep you from being thrown
against the inside of the car and
against other occupants.
Keep you from being thrown out
of the car.
Help keep you in a good position
should the airbags ever deploy. A
good position reduces the risk of
injury from an inflating airbag, and
allows you to get the best
advantage from the airbag.
Of course, seat belts cannot
completely protect you in every
crash.Butinmostcases,seatbelts
can reduce your risk of serious
injury.
What you should do:
Always wear
your seat belt, and make sure you
wear it properly.
Airbags
Your car has a Supplemental
Restraint System (SRS) with dualstage, dual-threshold front airbags to
help protect the heads and chests of
the driver and a front seat passenger
during a moderate to severe frontal
collision.
Standard on EX and all V 6 models
Optional on LX model
Your car also has side airbags to help
protect the upper torso of the driver
or a front seat passenger during a
moderate to severe side impact.
CONTINUED
Driver and Passenger Saf ety
9
Your Car’s Saf ety Features
Main Menu
Table of Content
Standard on U.S. EX-V6 model
Your car also has side curtain
airbags. During a moderate to severe
side impact, side curtain airbags help
to protect the heads of the driver,
front seat passenger, and passengers
sitting in the outer rear seating
positions.
10
Driver and Passenger Saf ety
The most important things you need
to know about your airbags are:
Airbags do not replace seat belts.
They are designed to supplement
the seat belts.
Airbags offer no protection in rear
impacts, rollovers, or minor
frontal or side collisions.
Airbags can pose serious hazards.
To do their job, airbags must
inflate with tremendous force and
speed. So while airbags help save
lives, they can cause minor injuries,
or more serious or even fatal
injuries if occupants are not
properly restrained or sitting
properly.
What you should do:
Always wear
your seat belt properly, and sit
upright and as far back as possible
from the steering wheel or
dashboard.
Your Car’s Saf ety Features
Main Menu
Table of Content
Seats & Seat-BacksHead Restraints
Your car’s seats are designed to keep
you in a comfortable, upright
position so you can take full
advantage of the protection offered
What you should do:
seats as far back as possible, and
keep adjustable seat-backs in an
upright position whenever the car is
moving.
by seat belts and the energy
Move the front
Head restraints can help protect you
from whiplash and other injuries. For
maximum protection, the back of
your head should rest against the
center of the head restraint.
absorbing materials in the seats.
Door Locks
How you adjust your seats and seatbacks can also affect your safety. For
example, sitting too close to the
steering wheel or dashboard
increases the risk of you or your
passenger being injured by striking
theinsideofthecar,orbyan
Keeping your doors locked reduces
thechanceofbeingthrownoutof
the car during a crash. It also helps
prevent occupants from accidentally
opening a door and falling out, and
outsiders f rom unexpectedly opening
your doors.
inflating airbag.
Reclining a seat-back too far reduces
the seat belt’s effectiveness and
increases the chance that the seat’s
occupant will slide under the seat
belt in a crash and be seriously
injured.
Driver and Passenger Saf ety
11
Your Car’s Saf ety Features
Main Menu
Table of Content
Pre-Drive Safety Checklist
To make sure you and your
passengers get the maximum
protection from your car’s safety
features, check the following each
time before you drive away:
All adults, and children who have
outgrown child safety seats, are
wearing their seat belts and
wearingthemproperly(seepage
).
16
Any infant or small child is
properly restrained in a child seat
inthebackseat(seepage).
12
Driver and Passenger Saf ety
21
Frontseatoccupantsaresitting
upright and as far back as possible
from the steering wheel and
dashboard (see page).
14
Seat-backs are upright (see page
).
15
Head restraints are properly
adjusted (see page).
16
Both doors are closed and locked
(see page).
13
All cargo is properly stored or
secured (see page).
234
The rest of this section gives more
detailed inf ormation about how you
can maximize your saf ety.
Remember, however, that no safety
system can prevent all injuries or
deaths that can occur in severe
crashes, even when seat belts are
properly worn and the airbags deploy.
Protecting Adults
Main Menu
Table of Content
IntroductionClose and Lock the Doors1.
The f ollowing pages provide
instructions on how to properly
protect the driver and other adult
occupants.
These instructions also apply to
children who have outgrown child
seats and are large enough to wear
lap/shoulder belts. (See pagefor
important additional guidelines on
how to properly protect larger
children.)
38
After everyone has entered the car,
be sure the doors are closed and
locked.
Your car has a door monitor light on
the instrument panel to indicate
when a specific door is not tightly
closed.
For safety, locking the doors reduces
the chance that a passenger,
especially a child, will open a door
while the car is moving and
accidentally fall out. It also reduces
the chance of someone being thrown
out of the car during a crash.
For security, locked doors can
prevent an outsider from
unexpectedly opening a door when
you come to a stop.
See pagefor how to lock the
86
doors.
Driver and Passenger Saf ety
13
Protecting Adults
Main Menu
Table of Content
Adjust the Front Seats2.
Any driver who sits too close to the
steering wheel is at risk of being
seriously injured or killed by striking
the steering wheel or from being
struck by an inflating front airbag
during a crash.
14
Driver and Passenger Saf ety
To reduce the chance of injury, wear
your seat belt properly, sit upright
with your back against the seat, and
movetheseatawayfromthe
steering wheel to the farthest
distance that allows you to maintain
full control of the car.
The National Highway Traffic Safety
Administration and Transport
Canada recommend that drivers
adjust the seat so the center of the
chest is at least 10 inches (25cm)
away from the center of the steering
wheel. In addition to adjusting the
seat, you can adjust the steering
wheel in and out (see page).
80
Also make sure your front seat
passenger moves the seat as f ar to
the rear as possible.
Sitting too close to a front
airbag can result in serious
injury or death if the front
airbags inflate.
Always sit as far back from the
front airbags as possible.
Most shorter drivers can get f ar
enough away from the steering
wheel and still reach the pedals.
However, if you are concerned about
sitting too close, we recommend that
you investigate whether some type
of adaptive equipment may help.
Once your seat is adjusted correctly,
rock it back and forth to make sure
the seat is locked in position.
See pagefor how to adjust the
94
front seats.
Protecting Adults
Main Menu
Table of Content
Adjust the Seat-Backs3.
Adjust the driver’s seat-back to a
comfortable, upright position,
leaving ample space between your
chest and the airbag cover in the
center of the steering wheel. If you
sit too close to the steering wheel,
you could be injured if the front
airbag inflates.
A front passenger should also adjust
the seat-back to an upright position,
but as far from the dashboard as
possible. A passenger who sits too
close to the dashboard could be
injured if the front airbag inflates.
Reclining a seat-back so that the
shoulder part of the belt no longer
rests against the occupant’s chest
reduces the protective capability of
the belt. It also increases the chance
of sliding under the belt in a crash
and being seriously injured. The
farther a seat-back is reclined, the
greater the risk of injury.
Reclining the seat-back too far
can result in serious injury or
death in a crash.
Adjust the seat-back to an
upright position and sit well
back in the seat.
See pagefor how to adjust seat-
94
backs.
Driver and Passenger Saf ety
15
Protecting Adults
Main Menu
Table of Content
Adjust the Head RestraintsFasten and Position the Seat
4.5.
Belts
Before driving, make sure everyone
with an adjustable head restraint has
properly positioned the head
restraint. The restraint should be
positioned so the back of the
occupant’s head rests against the
center of the restraint. A taller
person should adjust the restraint as
high as possible.
Improperly positioning head
restraints reduces their
effectiveness and you can be
seriously injured in a crash.
Make sure head restraints are
in place and positioned properly
before driving.
Properly adjusted head restraints
will help protect occupants from
whiplash and other crash injuries.
See pagefor how to adjust the
99
head restraints.
Insert the latch plate into the buckle,
then tug on the belt to make sure the
belt is securely latched. Also check
that the belt is not twisted, because a
twisted belt can cause serious
injuries in a crash.
16
Driver and Passenger Saf ety
Protecting Adults
Main Menu
Table of Content
Position the lap part of the belt as
low as possible across your hips,
then pull up on the shoulder part of
the belt so the lap part fits snugly.
This lets your strong pelvic bones
take the force of a crash and reduces
the chance of internal injuries.
If necessary, pull up on the belt again
to remove any slack from the
shoulder part, then check that the
belt rests across the center of your
chest and over your shoulder. This
spreads the forces of a crash over
the strongest bones in your upper
body.
Improperly positioning the seat
belts can cause serious injury
or death in a crash.
Make sure all seat belts are
properly positioned before
driving.
Never place the shoulder portion of a
lap/shoulder belt under your arm or
behind your back.
This could cause
very serious injuries in a crash.
If a seat belt does not seem to work
as it should, it may not protect the
occupant in a crash.
sit in a seat with an inoperative seat
belt.
Anyone using a seat belt that is
No one should
not working properly can be
seriously injured or killed. Have your
Honda dealer check the belt as soon
as possible.
See pagef or additional
46
information about your seat belt
system and how to take care of your
belts.
Driver and Passenger Saf ety
17
Protecting Adults
Main Menu
Table of Content
Adjust the Steering WheelMaintain a Proper Sitting
6.7.
Position
After all occupants have adjusted
their seats and put on seat belts, it is
very important that they continue to
sit upright, well back in their seats,
with their feet on the floor, until the
car is parked and the engine is off.
Sitting improperly can increase the
chance of injury during a crash. For
example, if an occupant slouches,
lies down, turns sideways, sits
forward, leans forward or sideways,
Adjust the steering wheel, if needed,
so that the wheel points toward your
chest, not toward your face.
Pointing the steering wheel toward
your chest provides optimal
protection from the airbag.
or puts one or both f eet up, the
chance of injury during a crash is
greatly increased.
In addition, an occupant who is out of
position in the front seat can be
seriously or f atally injured by
striking interior parts of the car, or
by being struck by an inflating front
airbag. Being struck by an inflating
side airbag can result in possibly
serious injuries.
Sitting improperly or out of
position can result in serious
injury or death in a crash.
Always sit upright, well back in
the seat, with your feet on the
floor.
See pagefor how to adjust the
80
steering wheel.
18
Driver and Passenger Saf ety
Protecting Adults
Main Menu
Table of Content
Remember, to get the best
protection from your car’s airbags
and other safety features, you must
sit properly and wear your seat belt
properly.
Advice for Pregnant Women
Because protecting the mother is the
best way to protect her unborn child,
a pregnant woman should always
wear a seat belt whenever she drives
or rides in a car.
Remember to keep the lap portion of
the belt as low as possible across
your hips.
Pregnant women should also sit
upright and as far back as possible
from the steering wheel or
dashboard. This will reduce the risk
of injuries to both the mother and
her unborn child that can be caused
by a crash or an inflating airbag.
Each time you have a check-up, ask
your doctor if it’s okay for you to
drive.
Driver and Passenger Saf ety
19
Protecting Adults
Main Menu
Table of Content
Additional Safety Precautions
Two people should never use the
same seat belt.
If they do, they
could be very seriously injured in a
crash.
Do not put any accessories on seat
belts.
Devices intended to improve
occupant comf ort or reposition the
shoulder part of a seat belt can
severely compromise the
protective capability of the seat
belt and increase the chance of
serious injury in a crash.
20
Driver and Passenger Saf ety
Do not place hard or sharp objects
between yourself and a front
airbag.
Carrying hard or sharp
objects on your lap, or driving with
a pipe or other sharp objects in
your mouth, can result in injuries
if your front airbag inflates.
Do not attach or place objects on
the front airbag covers.
Any object
attached to or placed on the covers
marked ‘‘SRS AIRBAG’’ in the
center of the steering wheel and
on top of the dashboard could
interfere with the proper operation
of the airbags. Or, if the airbags
inflate, the objects could be
propelled inside the car and hurt
someone.
On models with side airbags or
side curtain airbags, do not attach
hard objects on or near a door.
If a
side airbag or a side curtain airbag
inflates,acupholderorotherhard
object attached on or near the
door could be propelled inside the
car and hurt someone.
Keep your hands and arms away
from the airbag covers.
If your
hands or arms are close to the
airbag cover in the center of the
steering wheel or on top of the
dashboard, they could be injured if
the front airbag inflates.
Protecting Children
Main Menu
Table of Content
All Children Must Be Restrained
Each year, many children are injured
Children who are unrestrained
or improperly restrained can be
seriously injured or killed in a
crash.
Any child too small for a seat
belt should be properly
restrained in a child seat. A
larger child should be properly
restrained with a seat belt.
Children depend on adults to protect
them. However, despite their best
intentions, many parents and other
adults may not know how to
properly
protect young passengers.
So if you have children, or if you ever
need to drive with a grandchild or
otherchildreninyourcar,besureto
read this section.(See page.)
or killed in vehicle crashes because
they are either unrestrained or not
properly restrained. In fact, vehicle
accidents are the number one cause
of death of children ages 12 and
under.
To reduce the number of child
deaths and injuries, every state and
Canadian province requires that
infants and children be restrained
whenever they ride in a vehicle.
Anychildwhoistoosmalltoweara
seat belt should be properly
restrained in a child seat.
.)
26
A larger child should always be
restrained with a seat belt, and use a
booster, if needed.
(See page
38
CONTINUED
Driver and Passenger Saf ety
21
Protecting Children
Main Menu
Table of Content
Additional Precautions to Parents
Neverholdaninfantorchildon
your lap.
If you are not wearing a
seat belt in a crash, you could be
thrown forward into the
dashboard and crush the child.
child can be torn from your arms
during a crash. For example, if
your car crashes into a parked
vehicleat30mph(48km/h),a
20-lb (9 kg) infant will become a
600-lb (275 kg) force, and you will
not be able to hold on.
Never put a seat belt over yourself
and an infant or child.
crash, the belt could press deep
into the child and cause very
serious injuries.
22
Driver and Passenger Saf ety
During a
Children Should Sit in the Back
Seat
According to accident statistics,
children of all ages and sizes are
safer when they are restrained in the
back seat, not the front seat. The
National Highway Traffic Safety
Administration and Transport
Canada recommend that all children
ages 12 and under be properly
restrained in the back seat.
In the back seat, children are less
likely to be injured by striking hard
interior parts during a collision or
hard braking. Also, children cannot
be injured by an inflating airbag
when they ride in the back.
The Passenger’s Front Airbag
Poses Serious Risks to Children
Front airbags have been designed to
help protect adults in a moderate to
severe f rontal collision. To do this,
the passenger’s front airbag is quite
large, and it inflates with tremendous
speed.Ifyouarewearingaseatbelt,the
Infants
Never put a rear-f acing child seat in
the front seat of a vehicle equipped
with a passenger’s front airbag.
If
the airbag inflates, it can hit the back
of the child seat with enough force
to kill or very seriously injure an
infant.
Protecting Children
Main Menu
Table of Content
Small Children
Placing a forward-facing child seat in
the front seat of a vehicle equipped
with a passenger’s front airbag can
be hazardous.
If the vehicle seat is
too far forward, or the child’s head is
thrown f orward during a collision, an
inflating front airbag can strike the
child with enough force to kill or
very seriously injure a small child.
Larger Children
Children who have outgrown child
seats are also at risk of being injured
or killed by an inflating passenger’s
front airbag.
Whenever possible,
larger children should sit in the back
seat, in a booster seat if needed, and
be properly restrained with a seat
belt. (See pagefor important
38
information about protecting larger
children.)
U.S. Models
To remind you of the passenger’s
front airbag hazards, and that
children must be properly restrained
in the back seat, your car has
warninglabelsonthedashboardand
on the driver’s and front passenger’s
visors. Please read and follow the
instructions on these labels.
CONTINUED
Driver and Passenger Saf ety
23
Protecting Children
Main Menu
Table of Content
Canadian Models
To remind you of the front airbag
hazards, your car has warning labels
on the driver’s and front passenger’s
visors. Please read and follow the
instructions on these labels.
24
Driver and Passenger Saf ety
If You Must Drive with Several
Children
Your car has three seating positions
in the back seat where children can
be properly restrained.
If you ever have to carry more than
three children in your car:
Place the largest child in the front
seat, provided the child is large
enough to wear a seat belt
properly (see page).
38
Move the vehicle seat as far to the
rear as possible (see page).
14
Have the child sit upright and well
backintheseat(seepage).
18
Make sure the seat belt is properly
positioned and secured (see page
16
).
Protecting Children
Main Menu
Table of Content
If a Child Requires Close
Attention
Many parents say they prefer to put
an infant or small child in the f ront
passenger seat so they can watch the
child, or because the child requires
attention.
Placing a child in the front seat
exposes the child to hazards from
the passenger’s front airbag, and
paying close attention to a child
distracts the driver f rom the
important tasks of driving, placing
both of you at risk.
If a child requires physical attention
or frequent visual contact, we
strongly recommend that another
adult ride with the child in the back
seat. The back seat is far safer for a
child than the front.
Additional Safety Precautions
Do not leave children alone in your
vehicle.
Leaving children without
adult supervision is illegal in most
states and Canadian provinces,
and can be very hazardous. For
example, infants and small
childrenleftinavehicleonahot
day can die from heatstroke. And
children left alone with the key in
the ignition can accidentally set
the vehicle in motion, possibly
injuring themselves or others.
Lock both doors and the trunk
when your car is not in use.
Children who play in cars can
accidentally get trapped inside the
trunk and be seriously injured or
could die. Teach your children not
to play in or around cars. Know
how to operate the emergency
trunk opener and decide if your
children should be shown how to
use this feature (see page).
Keep car keys/remote
transmitters out of the reach of
children.
Even very young
93
children learn how to unlock
vehicle doors, turn on the ignition,
and open the trunk, which can
lead to accidental injury or death.
Driver and Passenger Saf ety
25
Protecting Children
Main Menu
Table of Content
General Guidelines for Using
Child Seats
The f ollowing pages give general
guidelines for selecting and installing
child seats for infants and small
children.
26
Driver and Passenger Saf ety
Selecting a Child Seat
To provide proper protection, a child
seat should meet three
requirements:
The child seat should meet safety
1.
standards.
The child seat should
meet Federal Motor Vehicle
Safety Standard 213 (FMVSS 213)
or Canadian Motor Vehicle Saf ety
Standard 213 (CMVSS 213). Look
for the manufacturer’s statement
of compliance on the boxes.
The child seat should be of the
2.
proper type and size to fit the child.
Infants:
Childrenuptoaboutone
year old should be restrained in a
rear-f acing, reclining child seat. Only
a rear-facing seat provides the
proper support to protect an inf ant’s
head, neck, and back. See page
for additional informationon
30
protecting infants.
The child seat should fit the
Main Menu
Table of Content
3.
vehicle seating position (or
positions) where it will be used.
Due to variations in the design of
child seats, vehicle seats, and seat
belts, all child seats will not fit all
vehicle seating positions.
Protecting Children
Before purchasing a child seat, we
recommend that parents test the
child seat in the specific vehicle
seating position (or positions) where
they intend to use the seat. If a
previously purchased child seat does
not fit, you may need to buy a
different one that will fit.
Small Children:
A child who is too
large for a rear-facing child seat, and
who can sit up without support,
should be restrained in a forwardfacing child seat. See pagefor
additional inf ormation on protecting
small children.
However, Honda is confident that
one or more child seat models can f it
andbeproperlyinstalledinall
recommended seating positions in
your car.
Your car has lower anchors installed
for use with LATCH (Lower
AnchorsandTethersforChildren)compatible child seats. For more
information, see page.3443
CONTINUED
Driver and Passenger Saf ety
27
Protecting Children
Main Menu
Table of Content
Placing a Child SeatFront Passenger’s Seat
This page briefly summarizes
Honda’s recommendations on where
to place rear-facing and forwardfacing child seats in your car.
Airbags Pose Serious
Risks to Children
The passenger’s front airbag
inflates with enough force to kill
or seriously injure an infant in a
rear-facing child seat.
A small child in a forward-facing
child seat is also at risk. If the
vehicle seat is too far forward,
or the child’s head is thrown
forward during a collision, an
inflating front airbag can kill or
seriously injure the child.
If a small child must ride in the
front, follow the instructions
provided in this section.
Infants:
Never in the front seat, due
to the front airbag hazard.
Small children:
Not recommended,
due to the front airbag hazard. If a
small child must ride in front,
move the vehicle seat to the rearmost position and secure a frontfacing child seat with the seat belt
(see page).
Back Seats
Infants:
35
Recommended positions.
Properlysecurearear-facingchild
seat (see pagesand).
Small children:
3143
Recommended
positions. Properly secure a frontfacing child seat (see pagesand
).
43
35
28
Driver and Passenger Saf ety
Protecting Children
Main Menu
Table of Content
Installing a Child Seat
After selecting a proper child seat,
and a good position to install the seat,
there are three main steps in
installing the seat:
Properly secure the child seat to
1.
the car.
All child seats are
designed to be secured to the car
with the lap part of a lap/shoulder
belt. Some child seats can be
secured to the vehicle’s LATCH
anchorage system instead. A child
whose seat is not properly secured
to the car can be endangered in a
crash. See pages,andfor
31 3543
instructions on how to properly
secure child seats in this car.
Make sure the child seat is firmly
2.
secured.
After installing a child
seat, push and pull the seat
forward and from side to side to
verify that it is secure.
To provide security during normal
driving maneuvers as well as during
a collision, we recommend that
parents secure a child seat as firmly
as possible.
However, a child seat does not need
to be ‘‘rock solid.’’ In some vehicles
or seating positions, it may be
diff icult to install a child seat so that
it does not move at all. Some side-toside or back-and-forth movement can
be expected and should not reduce
the child seat’s effectiveness.
If the child seat is not secure, try
installing it in a different seating
position, or use a different style of
child seat that can be firmly secured
in the desired seating position.
Secure the child in the child seat.
3.
Make sure the child is properly
strappedinthechildseat
according to the child seat maker’s
instructions. A child who is not
properly secured in a child seat
canbethrownoutoftheseatina
crash and be seriously injured.
Storing a Child Seat
When you are not using a child seat,
either remove it and store it in a safe
place, or make sure it is properly
secured. An unsecured child seat can
be thrown around the car during a
crash or sudden stop and injure
someone.
Driver and Passenger Saf ety
29
Protecting Children
Main Menu
Table of Content
Protecting Infants
Child Seat Type
Only a rear-facing child seat provides
proper support for a baby’s head,
neck, and back. Infants up to about
one year of age must be restrained in
a rear-facing child seat.
Two types of seats may be used: a
seat designed exclusively for infants,
or a convertible seat used in the rearfacing, reclining mode.
30
Driver and Passenger Saf ety
Placing a rear-facing child seat
in the front seat can result in
serious injury or death if the
passenger’s front airbag inflates.
Always place a rear-facing child
seat in the back seat, not the
front.
We recommend that an infant be
restrained in a rear-f acing child seat
until the infant is at least one year
old, reaches the seat maker’s weight
or height limit, and is able to sit up
without support.
Rear-Facing Child Seat Placement
In this car, a rear-facing child seat
can be placed in any seating position
in the back seat, but not in the front
seat.
Never put a rear-f acing child seat in
the front seat.
If the passenger’s
front airbag inflates, it can hit the
back of the child seat with enough
force to kill or seriously injure an
infant. If an infant must be closely
watched, we recommend that
another adult sit in the back seat
with the baby.
Do not put a rear-facing child seat in
a forward-facing position.
If placed
facing forward, an infant could be
very seriously injured during a
frontal collision.
Protecting Children
Main Menu
Table of Content
When properly installed, a rearfacing child seat may prevent the
driver or a front-seat passenger f rom
moving the seat as far back as
recommended (see page). Or it
may prevent them from locking the
seat-back in the desired upright
position (see page).
15
In either case, we recommend that
you place the child seat directly
behind the front passenger seat,
move the front seat as far forward as
needed, and leave it unoccupied. Or
you may wish to get a smaller child
seat that allows you to safely carry a
front passenger.
14
Rear-Facing Child Seat Installation
The lap/shoulder belts in the back
seats have a locking mechanism that
must be activated to secure a child
seat.
The f ollowing pages provide
instructions and tips on how to
secure a rear-facing child seat with
this type of seat belt.
If you have a child seat designed to
be attached to the vehicle’s LATCH
anchorage system, follow the
instructions on page.
43
With the child seat in the desired
1.
back seating position, route the
belt through the child seat
according to the seat maker’s
instructions, then insert the latch
plate into the buckle.
CONTINUED
Driver and Passenger Saf ety
31
Protecting Children
Main Menu
Table of Content
After the belt has retracted, tug on
3.
it. If the belt is locked, you will not
be able to pull it out. If you can pull
the belt out, it is not locked and
you will need to repeat these steps.
To activate the lockable retractor,
2.
slowly pull the shoulder part of the
belt all the way out until it stops,
then let the belt feed back into the
retractor (you might hear a
clicking noise as the belt retracts).
32
Driver and Passenger Saf ety
After confirming that the belt is
4.
locked, grab the shoulder part of
the belt near the buckle and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child seat will not be secure.
To remove slack, it may help to
putweightonthechildseat,or
push on the back of the seat, while
pulling up on the belt.
Protecting Children
Main Menu
Table of Content
Push and pull the child seat
5.
forward and from side to side to
verify that it is secure enough to
stay upright during normal driving
maneuvers. If the child seat is not
secure, unlatch the belt, allow it to
retract fully, then repeat these
steps.
To deactivate the locking
mechanism and remove a child seat,
unlatch the buckle, unroute the seat
belt, and let the belt f ully retract.
Rear-Facing Child Seat Installation
Tips
Forproperprotection,aninfantmust
ride in a reclined, or semi-reclined
position. To determine the proper
reclining angle, check with the baby’s
doctor or f ollow the seat maker’s
recommendations.
To achieve the desired reclining
angle, it may help to put a rolled up
towel under the toe of the child seat,
as shown.
Driver and Passenger Saf ety
33
Protecting Children
Main Menu
Table of Content
Protecting Small Children
Child Seat Type
A child at least one year old who can
sit up without support, and who fits
within the child seat maker’s weight
and height limits, should be
restrained in a forward-facing,
upright child seat.
Of the different seats available, we
recommend those that have a fivepoint harness system as shown.
34
Driver and Passenger Saf ety
We also recommend that a small
child stay in the child seat as long as
possible, until the child reaches the
weight or height limit for the seat.
Child Seat Placement
In this car, the best place to install a
forward-facing child seat is in one of
the seating positions in the back seat.
Placing a forward-facing child seat in
the front seat of a vehicle equipped
with a passenger’s front airbag can
be hazardous.
If the vehicle seat is
too far forward, or the child’s head is
thrown f orward during a collision, an
inflating front airbag can strike the
child with enough force to cause
very serious or fatal injuries. If a
small child must be closely watched,
we recommend that another adult sit
in the back seat with the child.
Improperly placing a forward-
Main Menu
Table of Content
facing child seat in the front
seat can result in serious injury
or death if the front airbags
inflate.
Ifyoumustplaceaforwardfacing child seat in front, move
the vehicle seat as far back as
possible and properly restrain
the child.
If it is necessary to put a forwardfacing child seat in the front, move
the vehicle seat as far to the rear as
possible, be sure the child seat is
firmly secured to the car, and the
child is properly strapped in the seat.
Child Seat Installation
The lap/shoulder belts in the back
and front passenger seating positions
have a locking mechanism that must
be activated to secure a child seat.
The f ollowing pages provide
instructions on how to secure a
forward-facing child seat with this
type of seat belt.
If you have a child seat designed to
be attached to the vehicle’s LATCH
anchorage system, follow the
instructions on page.1.43
Protecting Children
With the child seat in the desired
seating position, route the belt
through the child seat according
to the seat maker’s instructions,
then insert the latch plate into the
buckle.
CONTINUED
Driver and Passenger Saf ety
35
Protecting Children
Main Menu
Table of Content
After the belt has retracted, tug on
3.
it. If the belt is locked, you will not
be able to pull it out. If you can pull
the belt out, it is not locked and
you will need to repeat these steps.
To activate the lockable retractor,
2.
slowly pull the shoulder part of the
belt all the way out until it stops,
then let the belt feed back into the
retractor (you might hear a
clicking noise as the belt retracts).
36
Driver and Passenger Saf ety
After confirming that the belt is
4.
locked, grab the shoulder part of
the belt near the buckle and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child seat will not be secure. It
mayhelptoputweightonthe
child seat, or push on the back of
the seat, while pulling up on the
belt.
Push and pull the child seat
Main Menu
Table of Content
5.
forward and from side to side to
verify that it is secure enough to
stay upright during normal driving
maneuvers. If the child seat is not
secure, unlatch the belt, allow it to
retract fully, then repeat these
steps.
Protecting Children
To deactivate the locking
mechanism and remove a child seat,
unlatch the buckle, unroute the seat
belt, and let the belt f ully retract.
Driver and Passenger Saf ety
37
Protecting Children
Main Menu
Table of Content
Protecting Larger Children
When a child reaches the
recommended weight or height limit
for a forward-facing child seat, the
child should sit in the back seat on a
booster and wear a lap/shoulder belt.
We recommend that the child use a
booster seat until the child is tall
enough to use the seat belt without a
booster.
The f ollowing pages give
instructions on how to check proper
seat belt fit, what kind of booster
seat to use if one is needed, and
important precautions for a child
who must sit in the front seat.
38
Driver and Passenger Saf ety
Checking Seat Belt Fit
Allowing a larger child to sit
improperly in the front seat can
result in injury or death if the
passenger’s front airbag inflates.
If a larger child must sit in front,
make sure the child moves the
seat as far back as possible,
uses a booster seat if needed,
and wears the seat belt properly.
To determine if a lap/shoulder belt
properly fits a child, have the child
sit in the rear seat, all the way back
against the seat, and put on the seat
belt. Follow the instructions on page
. Then check how the belt fits.16
Protecting Children
Main Menu
Table of Content
If the shoulder part of the belt rests
over the child’s collarbone and
against the center of the chest, and
the lap belt rests over the child’s
hipbones and touches the tops of the
thighs as shown, the child is
probably big enough to wear the seat
belt.
However, if the shoulder belt
touchesorcrossesthechild’sneck,
or if the lap belt crosses the child’s
stomach, the child needs to use a
booster seat.
Do not let a child wear a seat belt
across the neck or over the stomach.
This could result in serious neck and
internal injuries during a crash.
part of a seat belt behind the back or
under the arm.
This could cause
very serious injuries during a crash.
It also increases the chance that the
child will slide under the belt in a
crash and be injured.
Do not put any accessories on a seat
belt.
Devices intended to improve
occupant comf ort or reposition the
shoulder part of a seat belt, severely
compromise the protective capability
of the seat belt and increase the
chance of serious injury in a crash.
Two children should never use the
same seat belt.
If they do, they could
be very seriously injured in a crash.
Using a Booster SeatDo not let a child put the shoulder
If a child needs a booster seat, we
recommend choosing a high or lowback style that allows the child to be
directly secured with the lap/
shoulder belt.
Whichever style you select, follow
the booster seat maker’s instructions.
CONTINUED
Driver and Passenger Saf ety
39
Protecting Children
Main Menu
Table of Content
A child should continue using a
booster seat until the child exceeds
the booster seat manufacturer’s
requirements.
Even then, the child may still need to
use a booster seat. Note that some
states now require children to use
boosters until they reach a certain
ageand/orweight.Besuretocheck
current laws in the state or states
where you intend to drive.
40
Driver and Passenger Saf ety
When Can a Larger Child Sit in Front
The National Highway Traffic Safety
Administration and Transport
Canada recommend that all children
ages 12 and under be properly
restrained in the back seat.
The back seat is the safest place for
a child of any age or size.
In addition, the passenger’s front
airbag poses serious risks to children.
If the seat is too far f orward, or the
child’s head is thrown forward
during a collision, or the child is
unrestrained or out of position, an
inflating front airbag can kill or
seriously injure the child.
The side airbag also poses risks. If
any part of a larger child’s body is in
the path of a deploying airbag, the
child could receive possibly serious
injuries.
Of course, children vary widely. And
while age may be one indicator of
when a child can safely ride in the
front, there are other important
factors you should consider.
Protecting Children
Main Menu
Table of Content
Physical Size
enough for the lap/shoulder belt to
properly fit over the hips, chest, and
shoulder (see pagesand). If
1638
the seat belt does not fit properly,
the child should not sit in the f ront.
Maturity
To safely ride in front, a child must
be able to f ollow the rules, including
sitting properly and wearing the seat
belt properly throughout a ride.
If you decide that a child can safely
ride up front, be sure to:Physically, a child must be large
and make sure you understand all
seat belt instructions and all safety
information.
Move the vehicle seat to the rearmost position.
Have the child sit up straight, back
against the seat, and feet on or
near the floor.
Check that the child’s seat belt is
properly positioned and secured.
Remind the child not to lean
toward the door because of the
side airbag.
Supervise the child. Even mature
children sometimes need to be
reminded to fasten the seat belts
or sit properly.Carefully read the owner’s manual
Driver and Passenger Saf ety
41
Protecting Children
Main Menu
Table of Content
Using Child Seats with Tethers
TETHER ANCHORAGE POINTS
COVER
Your car has three tether anchorage
points under the rear window for
securing a tether-style child seat to
the car.
Since a tether can provide additional
security, we recommend using a
tether whenever one is required or
available. (Tethers are required in
Canada.)
42
Driver and Passenger Saf ety
The tether anchorage points are
located under plastic covers. Pivot
the cover backward to access the
anchorage point.
To use either outside anchorage
point, lift the rear head restraint,
then route the tether strap over the
seat-back between the legs of the
head restraint.
Protecting Children
Main Menu
Table of Content
TETHER STRAP HOOK
TETHER ANCHORAGE POINT
Attach the tether strap hook to the
tether anchorage point as shown in
the illustration, then tighten the
strap according to the child seat
maker’s instructions. Make sure the
strap is not twisted.
Using LATCH
LOWER ANCHORS
Your car is equipped with LATCH
(Lower Anchors and Tethers for
Children) at the outer rear seats.
The lower anchors are located
between the seat-back and seat
bottom and are to be used only with
a child seat designed for use with
LATCH.
The exact location of each lower
anchor is marked with a small button
above the lower anchor point.
To install a LATCH-compatible child
seat:
Move the seat belt buckle or
1.
center seat belt away from the
lower anchors.
Make sure there are no foreign
2.
objects around the anchors.
Foreign objects could get in the
way of a secure connection
between the child seat and the
anchors.
CONTINUED
Driver and Passenger Saf ety
43
Protecting Children
Main Menu
Table of Content
Rigid type
Put the child seat in the rear left
3.4.5.
or right vehicle seat and attach the
child seat to the lower anchors
according to the child seat maker’s
Flexible type
Follow the child seat maker’s
instructions for any additional
advice on adjusting or tightening
the fit.
instructions.
44
Driver and Passenger Saf ety
Lift the rear head restraint, then
route the tether strap over the
seat-back between the legs of the
head restraint.
Protecting Children
Main Menu
Table of Content
Attach the tether strap hook to the
6.
tether anchorage point, and
tighten the strap according to the
child seat maker’s instructions.
Make sure the strap is not twisted.
Push and pull the child seat
7.
forward and from side to side to
verify that it is secure enough to
stay upright during normal driving
maneuvers.
Lower Universal Anchorage System
Symbol
Canadian models only
This symbol on rear or forward
facing child seats or booster
cushions indicates the presence of
LATCH compatible hardware.
Driver and Passenger Saf ety
45
Additional Information About Your Seat Belts
Main Menu
Table of Content
Seat Belt System ComponentsLap/Shoulder Belt
Your seat belt system includes lap/
shoulder belts in all five seating
positions. The front seat belts are
also equipped with automatic seat
belt tensioners.
The seat belt system also
includes a light on the
instrument panel to remind you and
your passengers to fasten your belts.
If the driver’s seat belt is not
fastened before the ignition is turned
ON (II), the light will come on and a
beeper will also sound. The beeper
will stop after a few seconds, but the
light will stay on until the driver’s
This seat belt has a single belt that
goes over your shoulder, across your
chest and across your hips.
seat belt is fastened.
To fasten the belt, insert the latch
plate into the buckle, then tug on the
belt to make sure the buckle is
latched.
46
Driver and Passenger Saf ety
To unlock the belt, push the red
PRESSbuttononthebuckle.
Guide the belt across your body to
the door pillar. After exiting the car,
be sure the belt is out of the way and
will not get closed in the door.
All seat belts have an emergency
locking retractor. In normal driving,
the retractor lets you move freely in
your seat while it keeps some
tension on the belt. During a collision
or sudden stop, the retractor
automatically locks the belt to help
restrain your body.
The seat belts in all seating positions
except the driver’s have an additional
locking mechanism that must be
activated to secure a child seat. (See
pagesandfor instructions on
3135
how to secure child seats with this
type of seat belt.)
Additional Information About Your Seat Belts
Main Menu
Table of Content
If the shoulder part of the belt is
pulled all the way out, the locking
mechanism will activate. The belt
will retract, but it will not allow the
passenger to move freely.
To deactivate the locking
mechanism, unlatch the buckle and
let the seat belt f ully retract. To
refasten the belt, pull it out only as
far as needed.
See pagef or instructions on how
to wear the lap/shoulder belt
properly.
Automatic Seat Belt Tensioners
For added protection, the front seat
belts are equipped with automatic
seat belt tensioners. When activated,
the tensioners immediately tighten
the belts to help hold the driver and
a front passenger in place.
The tensioners are designed to
activate primarily in f rontal collisions.
The tensioners are independent of
the airbag system, so they can be
activated during a collision that
might not cause the airbags to
deploy. In this case, the airbags
would not be needed but the
additional seat belt tension can be
helpful.
The tensioners will be activated in a
collision severe enough to cause the
front airbags to inflate.
When the tensioners are activated,
the seat belts will remain tight until
they are unbuckled in the normal
way.
The SRS indicator light will
come on if there is a
problem with your automatic seat
belt tensioners (see page).1652
Driver and Passenger Saf ety
47
Additional Information About Your Seat Belts
Main Menu
Table of Content
Seat Belt Maintenance
For safety, you should check the
condition of your seat belts regularly.
Pull each belt out fully and look for
frays, cuts, burns, and wear. Check
that the latches work smoothly and
that the lap/shoulder belts retract
easily. Any belt not in good condition
or not working properly will not
provide good protection and should
be replaced as soon as possible.
U.S. Models
Honda provides a lifetime warranty
on seat belts. Honda will repair or
replace any seat belt component that
fails to function properly during
normal use. Please see your
Warranty Information
booklet for
details.
48
Driver and Passenger Saf ety
Honda
Not checking or maintaining
seat belts can result in serious
injury or death if the seat belts
do not work properly when
needed.
Check your seat belts regularly
and have any problem
corrected as soon as possible.
If a seat belt is worn during a crash,
it must be replaced by the dealer. A
belt that has been worn during a
crash may not provide the same level
of protection in a subsequent crash.
The dealer should also inspect the
anchors for damage and replace
them if needed.
Automatic seat belt tensioners that
deployed during a crash must be
replaced.
For information on how to clean your
seat belts, see page.
359
Additional Information About Your Airbags
Main Menu
Table of Content
SRS ComponentsHow Your Front Airbags Work
Your Supplemental Restraint System
(SRS) includes:
A sophisticated electronic system
that continually monitors and
records information about the
sensors, the control unit, the
Two front airbags. The driver’s
airbag is stored in the center of
the steering wheel; the front
airbag activators, and driver and
passenger seat belt use when the
ignition is ON (II).
passenger’sairbagisstoredinthe
dashboard. Both are marked ‘‘SRS
AIRBAG.’’
An indicator light on the
instrument panel that alerts you to
a possible problem with the
Automatic seat belt tensioners
(see page).
47
system (see page).
52
Emergency backup power in case
Sensors that can detect a
moderate to severe frontal
collision.
your car’s electrical system is
disconnected in a crash.
Your car is equipped with dual-stage,
dual-threshold airbags to help reduce
the chance of airbag-caused injuries.
Driver and Passenger Saf ety
CONTINUED
49
Additional Information About Your Airbags
Main Menu
Table of Content
If you ever have a moderate to
severe f rontal collision, the sensors
will detect the vehicle’s rapid
deceleration. If the rate of
deceleration is high enough, the
control unit will instantly inflate the
front airbags.
50
Driver and Passenger Saf ety
During a frontal crash, your seat
belts help restrain your lower body
and torso. Your airbag provides a
cushion to help restrain and protect
your head and chest.
Since both airbags use the same
sensors, both airbags normally
inflate at the same time. However, it
is possible for only one airbag to
inflate.
This can occur when the severity of
a collision is at the margin, or
threshold, that determines whether
or not the airbags will deploy. In
such cases, the seat belt will provide
sufficient protection, and the
supplemental protection offered by
the airbag would be minimal.
After inflating, the front airbags
immediately deflate, so they won’t
interfere with the driver’s visibility,
or the ability to steer or operate
other controls.
The total time for inflation and
deflation is approximately one-tenth
of a second, so fast that most
occupants are not aware that the
airbags deployed until they see them
lying in their laps.
Additional Information About Your Airbags
Main Menu
Table of Content
After a crash, you may see what
looks like smoke. This is actually
powder from the airbag’s surface.
Although the powder is not harmf ul,
people with respiratory problems
mayexperiencesometemporary
discomfort. If this occurs, get out of
the car as soon as it is safe to do so.
U.S. Owners:
For additional information on how
your airbags work, see the booklet
SRS: What You Need to Know
titled
About Airbags
that came with your
owner’s manual.
Canadian Owners:
For additional information on how
your airbags work, ask your dealer
for a copy of the booklet titled
What You Need to Know About Airbags
SRS:
How Your Side Airbags Work
Only on models equipped with side
airbags
airbags for the driver and a front
seat passenger. The airbags are
stored in the outer edges of the front
.
seat-backs, and both are marked
‘‘SIDE AIRBAG.’’
In a moderate to severe side impact,
the sensors will detect rapid
deceleration and signal the control
unit to instantly inflate either the
driver’s or the passenger’s side
airbag.
Only one airbag will deploy during a
side impact. If the impact is on the
passenger’s side, the passenger’s
side airbag will deploy even if there
is no passenger.
To get the best protection from the
side airbags, front seat occupants
should wear their seat belts and sit
upright and well back in their seats.Some models are equipped with side
Driver and Passenger Saf ety
51
Additional Information About Your Airbags
Main Menu
Table of Content
Work
SIDE CURTAIN AIRBAG
Standard on U.S. EX-V6 model
Your car is equipped with side
curtain airbags. These airbags are
stored in the front, center, and rear
pillars on both sides. The front and
rear pillars on both sides are marked
‘‘SIDE CURTAIN AIRBAG.’’
52
Driver and Passenger Saf ety
In a moderate to severe side impact,
sensors will detect rapid deceleration
and signal the control unit to
instantly inflate the side curtain
airbag on the driver’s or the
passenger’s side of the car. If the
impact is on the passenger’s side, the
passenger’s side curtain airbag will
inflate even if there are no occupants
on that side of the car.
To get the best protection from the
side curtain airbags, occupants
should wear their seat belts and sit
upright and well back in their seats.
How the SRS Indicator WorksHow Your Side Curtain Airbags
The SRS indicator alerts
you to a potential problem
with your f ront airbags. This light
will also alert you to a potential
problem with your automatic seat
belt tensioners (page).
47
On models with side airbags, this
light will also alert you to a potential
problem with your side airbags, the
passenger’s side airbag automatic
cutoff system (see page), or the
53
side curtain airbags.
When you turn the ignition ON (II),
this indicator will light brief ly then
go out. This tells you that the system
is working properly.
Additional Information About Your Airbags
Main Menu
Table of Content
If the light comes on at any other
time, or does not come on at all, you
should have the system checked by
your dealer. For example:
If the SRS indicator light does not
come on after you turn the ignition
switch to ON (II).
If the light stays on after the
engine starts.
If the light comes on or f lashes on
andoffwhileyoudrive.
If you see any of these indications,
your airbags may not deploy, your
passenger’s side airbag automatic
cutoff system may not work properly,
or your seat belt tensioners may not
work when you need them. See your
Honda dealer as soon as possible.
Ignoring the SRS indicator light
can result in serious injury or
death if the airbags, cutoff
system, or tensioners do not
work properly.
Have your vehicle checked by a
dealer as soon as possible if
the SRS light alerts you to a
potential problem.
How the Side Airbag Cutoff
Indicator Light Works
Only on models equipped with side
airbags
This light alerts you that
the passenger’s side airbag
has been automatically shut off.
To reduce the risk of injury from an
inflating side airbag, your car has an
automatic cutoff system for the
passenger’s side airbag.
It does not mean there is a problem
with your side airbags. It means that
thesideairbagcutoffsystemhas
activated to prevent the side airbag
from deploying.
CONTINUED
Driver and Passenger Saf ety
53
Additional Information About Your Airbags
Main Menu
Table of Content
Although Honda does not encourage
children to ride in the front, this
system is designed to shut off the
side airbag if a child leans sideways
and the child’s head is in the side
airbag deployment path.
If a small-statured adult leans
sideways, or larger adult slouches
and leans sideways into the
deployment path of the side airbag,
the system may also shut off the side
airbag.
If the side airbag cutoff indicator
light comes on, you should have the
passenger sit upright. Once the
passenger is out of the deployment
path of the side airbag, the system
will turn the airbag back on and the
light will go out.
54
Driver and Passenger Saf ety
A front seat passenger should not
use a cushion or other object as a
backrest. It may prevent the cutoff
system f rom working properly.
When you turn the ignition switch to
ON (II), the indicator should light
briefly and go out (see page). If it
63
doesn’t light, stays on, or comes on
while driving without a passenger in
the front seat, have the system
checked.
Additional Information About Your Airbags
Main Menu
Table of Content
Airbag ServiceAdditional Saf ety Precautions
Your airbag systems are virtually
maintenance-free, and there are no
parts you can safely service.
However, you must have your car
Donotattempttodeactivateyour
airbags.
Together, airbags and
seat belts provide the best
protection.
serviced if :
Do not tamper with airbag
Your airbags ever inflate.
Any
airbag that has deployed must be
replaced along with the control
unit, automatic seat belt
components or wiring for any
reason.
Tampering could cause
the airbags to deploy, possibly
causing very serious injury.
tensioners, and other related parts.
Do not try to remove or replace
anyairbagbyyourself.Thismust
be done by a Honda dealer or a
knowledgeable body shop.
Do not expose the front seat-backs
to water.
If rain or spilled water
soaks into a seat-back, it can
prevent the side airbag system
from working properly.
The SRS indicator light alert s you
to a problem.
Take your car to an
authorized Honda dealer as soon
as possible. If you ignore this
indication, the airbags might not
inflate when you need them.
Do not cover or replace front seatback covers without consulting a
Honda dealer.
Improperly
replacing or covering front seatback covers can prevent your side
airbags from inflating during a
collision.
See pagefor further information
233
and precautions relating to your
airbags.
Driver and Passenger Saf ety
55
Carbon Monoxide Hazard
Main Menu
Table of Content
Your car’s exhaust contains carbon
monoxide gas. You should have no
problem with carbon monoxide
entering the car in normal driving if
you maintain your car properly.
Have the exhaust system inspected
for leaks whenever:
The car is raised for an oil change.
You notice a change in the sound
of the exhaust.
Thecarwasinanaccidentthat
may have damaged the underside.High levels of carbon monoxide can
56
Driver and Passenger Saf ety
Carbon monoxide gas is toxic.
Breathing it can cause
unconsciousness and even kill
you.
Avoid any enclosed areas or
activities that expose you to
carbon monoxide.
collect rapidly in enclosed areas,
such as a garage. Do not run the
engine with the garage door closed.
Even with the door open, run the
engine only long enough to move the
car out of the garage.
With the trunk lid open, air flow can
pull exhaust gas into your car’s
interior and create a hazardous
condition. If you must drive with the
trunk lid open, open all the windows
and set the heating and cooling
system/climate control system as
shown below.
If you must sit in your parked car,
even in an unconf ined area, with the
engine running, adjust the heating
and cooling system/climate control
system as follows:
Select the Fresh Air mode.
1.
Select themode.
2.
Turn the fan on high speed.
3.
Set the temperature control to a
4.
comfortable setting.
Safety Labels
Main Menu
Table of Content
These labels are in the locations
shown. They warn you of potential
hazards that could cause serious
injury. Read these labels caref ully.
If a label comes off or becomes hard
to read (except for the U.S.
dashboard label which is removed by
the owner), contact your Honda
dealer for a replacement.
HOOD
On models without side airbags
On models with side airbags
On models with side
curtain airbags
U.S. models
Canadian models
DASHBOARD
U.S. models only
RADIATOR CAP
CONTINUED
Driver and Passenger Saf ety
57
Safety Labels
Main Menu
Table of Content
SUN VISOR
U.S. models
Canadian models
58
Driver and Passenger Saf ety
DOORJAMBS
On cars with side airbags
U.S. modelsCanadian models
On cars with side curtain airbags
U.S. modelsCanadian models
Instruments and Controls
Main Menu
This section gives information about
the controls and displays that
contribute to the daily operation of
your Honda. All the essential
controls are within easy reach.
The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.
LOW OIL PRESSURE
INDICATOR
(P.62, 380)
ANTI-LOCK BRAKE SYSTEM
INDICATOR
CRUISE MAIN INDICATOR
(P.62, 379)
HIGH BEAM INDICATOR
LOW FUEL INDICATOR
PARKING BRAKE AND BRAKE
SYSTEM INDICATOR
*
(P.63)
(P.64)
(P.67)
(P.67)
TCS ACTIVATION INDICATOR
CRUISE CONTROL INDICATOR
TRACTION CONTROL SYSTEM (TCS)
INDICATOR
IMMOBILIZER SYSTEM INDICATOR(P.65)
SECURITY SYSTEM INDICATOR
(P.66)
(P.66, 213)
LIGHTS ON INDICATOR
SEAT BELT REMINDER LIGHT
(P.64)
(P.67)
(P.64)
MAINTENANCE REQUIRED
INDICATOR
SUPPLEMENTAL
RESTRAINT SYSTEM
INDICATOR
Instruments and Cont rols
(P.71)
DOOR AND TRUNK
OPEN MONITOR
SIDE AIRBAG CUTOFF
INDICATOR
(P.66)
(P.63)
(P.63)
(P.62)
(P.65)
61
Indicator Lights
Main Menu
Table of Content
The instrument panel has many
Seat Belt Reminder Light
indicators to give you important
information about your car.The engine can be severely damaged
This indicator lights when you turn
the ignition switch ON (II). It is a
reminder to you and your passengers
to protect yourselves by fastening
if this light flashes or stays on when
the engine is running. For complete
information, see page.
Low Oil Pressure
Indicator
379
the seat belts. A beeper also sounds
if you have not fastened your seat
belt.
Charging System
Indicator
If this light comes on when the
If you do not fasten your seat belt,
the beeper will stop after a few
seconds but the light stays on until
engine is running, the battery is not
being charged. For complete
information, see page.
380
you do. Both the light and the beeper
62
Instruments and Cont rols
stay off if you fasten your seat belt
before turning on the ignition.
See page.
Malfunction Indicator
Lamp
381
Indicator Lights
Main Menu
Table of Content
U.S.Canada
Parking Brake and Brake System
Indicator
This light has two functions:
This indicator comes on when you
1.
turn the ignition switch ON (II). It
is a reminder to check the parking
brake. Driving with the parking
brake not fully released can
damage the brakes and tires.
If the indicator remains lit after
2.
you have f ully released the
parking brake while the engine is
running, or if it comes on while
driving, it can indicate a problem
in the brake system. For complete
information, see page.
383
Supplemental Restraint
System Indicator
This indicator lights brief ly when
you turn the ignition switch to ON
(II). If it comes on at any other time,
it indicates a potential problem with
your front airbags. This light will
also alert you to a potential problem
with your side airbags, passenger’s
side airbag automatic cutoff system,
side curtain airbags or automatic
seat belt tensioners. For complete
information, see page.
52
Side Airbag Cutof f
Indicator
Only on models equipped with side
airbags
This indicator lights brief ly when
you turn the ignition switch ON (II).
If it comes on at any other time, it
indicates that the passenger’s side
airbag has automatically shut off.
For complete information, see page
.
53
Instruments and Cont rols
63
Indicator Lights
Main Menu
Table of Content
Anti-lock Brake System
(ABS) Indicator
This light normally comes on for a
few seconds when you turn the
ignition switch ON (II). If this light
comes on at any other time, there is
a problem in the ABS. If this happens,
take the car to your dealer to have it
checked. With the light on, your car
still has normal braking ability but no
anti-lock. For complete information,
see page.
64
255
Instruments and Cont rols
TCS Activation IndicatorTraction Control System
(TCS) Indicator
On all V6 modelsOn all V6 models
This indicator has three functions:
Itcomesonasareminderthatyou
1.
have turned off the Traction
Control System.
This indicator normally comes on for
a few seconds when you turn the
ignition switch to ON (II). If it comes
on and stays on with the TCS
Activation Indicator, there is a
It flashes when the TCS is
2.
regulating wheelspin.
Ifitcomesonandstaysonwhen
3.
problem with the TCS. For more
information on the TCS, see page
.
258
the Traction Control System is on,
it indicates that there is a problem
in the TCS.
This indicator normally also comes
on for a few seconds when you turn
the ignition switch to ON (II). If this
lightcomesonandstaysonatany
other time, or it does not come on
when you turn the ignition switch to
ON (II), there is a problem with the
TCS. Take the car to your dealer to
have it checked. See pagefor
258
more information on the TCS.
Indicator Lights
Main Menu
Table of Content
Immobilizer System
Indicator
This indicator comes on for a few
seconds when you turn the ignition
switch ON (II). It will then go off if
you have inserted a properly-coded
ignition key. If it is not a properlycoded key, the indicator will blink
and the engine will not start (see
page).
83
This indicator also blinks several
times when you turn the ignition
switch from ON (II) to ACCESSORY
(I) or LOCK (0).
Door and Trunk Open Monitor
The appropriate light comes on in
this display if the trunk or either
door is not closed tightly.
All the lights in the monitor display
come on for a few seconds when you
turn the ignition switch to ON (II).
Turn Signal and
Hazard Warning
Indicators
The lef t or right turn signal light
blinks when you signal a lane change
or turn. If the light does not blink or
blinks rapidly, it usually means one
of the turn signal bulbs is burned out
(see page). Replace the bulb as
346
soon as possible, since other drivers
cannot see that you are signaling.
WhenyouturnontheHazard
Warning switch, both turn signal
lights blink. All turn signals on the
outside of the car should flash.
Instruments and Cont rols
65
Indicator Lights
Main Menu
Table of Content
Lights On IndicatorLow Fuel IndicatorSecurity System Indicator
This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
orposition. If you turn the
ignition switch to ACCESSORY (I)
or LOCK (0) without turning off the
light switch, this indicator will
remain on. A reminder chime will
also sound when you open the driver’s
door.
66
Instruments and Cont rols
LOW FUEL INDICATOR
This indicator is located in the fuel
gauge. It comes on as a reminder
that you must refuel soon.
SECURITY SYSTEM INDICATOR
This indicator lights when the
security system is set. See page
for complete information on the
213
security system.
Indicator Lights
Main Menu
Table of Content
‘‘Daytime Running
Lights’’ Indicator
This indicator lights when you turn
the ignition switch to ON (II) with
the headlight switch off and the
parking brake set. It should go off if
youturnontheheadlightsorrelease
the parking brake. If it comes on at
any other time, it means there is a
problem with the DRL. There may
also be a problem with the high
beam headlights.
High Beam Indicator
This light comes on with the high
beam headlights. See pagefor
information on the headlight
controls.
On Canadian models, this indicator
comes on with reduced brightness
when the Daytime Running Lights
(DRL) are on (see page).
76
74
Cruise Main Indicator
This indicator comes on when you
turn on the Cruise Control System
by pressing the Master Button. (see
page.)
214
Cruise Control Indicator
This lights when you set the cruise
control. See pagefor information
214
on operating the cruise control.
Washer Level Indicator
Canadian models onlyCanadian models only
This light comes on when the
washer fluid level is low. Add washer
fluid when you see this light come on
(see page).
306
Instruments and Cont rols
67
Gauges
Main Menu
Table of Content
The gauges illuminate when you
turn the ignition switch to ON (II).
Speedometer
U.S. Models
This shows your speed in miles per
hour (mph). The smaller inner
numbers are the speed in kilometers
per hour (km/h).
Canadian Models
This shows your speed in kilometers
per hour (km/h). The smaller inner
numbers are the speed in miles per
hour (mph).
Tachometer
The tachometer shows the engine
speed in revolutions per minute
(rpm). To protect the engine from
damage, never drive with the
tachometer needle in the red zone.
68
Instruments and Cont rols
TACHOMETER
ODOMETER/OUTSIDE
TEMPERATURE INDICATOR
U.S. model is shown.
SPEEDOMETER
TRIP METER
FUEL GAUGE
MAINTENANCE
REQUIRED
INDICATOR
TEMPERATURE
GAUGE
SELECT/RESET
KNOB
Gauges
Main Menu
Table of Content
OdometerOutside Temperature Indicator
The odometer shows the total distance your car has been driven. It
measures miles in U.S. models and
kilometers in Canadian models.
It is illegal under U.S. federal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
On 4-cylinder EX model with leather
interior and 6-cylinder EX model
This indicator displays the outside
temperature in Fahrenheit in U.S.
models, and in Centigrade in
Canadian models. To see the outside
temperature, press and release the
Select/Reset knob until the
temperature is displayed.
indicated.
The temperature sensor is located in
The odometer and the outside
temperature indicator use the same
display. To switch the display
between the odometer and the
outside temperature, press the
Select/Reset knob. When you turn
the ignition switch to ON (II), what
you last selected is displayed.
the front bumper. Therefore, the
temperature reading can be affected
by heat reflection from the road sur-
face, engine heat, and the exhaust
from surrounding traffic. This can
cause an incorrect temperature read-
ing when your speed is under
19 mph (30 km/h).
In certain weather conditions,
temperature readings near freezing
(32°F, 0°C) could mean that ice is
forming on the road surface.
Instruments and Cont rols
69
Gauges
Main Menu
Table of Content
Trip MeterTemperature GaugeFuel Gauge
This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
There are two trip meters: Trip A
and Trip B. Switch between these
displays and the odometer/outside
temperature display by pressing the
Select/Reset knob repeatedly. Each
trip meter works independently, so
you can keep track of two different
distances.
When you turn the ignition switch to
ON (II), what you last selected is
displayed.
To reset a trip meter, display it, and
then press and hold the Select/Reset
knob until the number resets to ‘‘0.0’’.
This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise into the
upper half of the gauge. If it reaches
the red (Hot) mark, pull safely to the
side of the road. Turn to pagefor
376
instructions and precautions on
checking the engine’s cooling
system.
This shows how much fuel you have.
It is most accurate when the car is on
level ground. It may show slightly
more or less than the actual amount
whenyouaredrivingoncurvyor
hilly roads.
The needle returns to the bottom
after you turn off the ignition. The
gauge shows the fuel level reading
immediately after you turn the
ignition switch back ON (II).
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.
70
Instruments and Cont rols
Gauges
Main Menu
Table of Content
Maintenance Required Indicator
MAINTENANCE REQUIRED
INDICATOR
This indicator reminds you that it is
time to take your car in for
scheduled maintenance per the
Normal Conditions maintenance
schedule. The indicator light does
not reflect severe maintenance
intervals.
Refer to the Maintenance Schedule
for Normal Driving Conditions on
page(4-cylinder models) or page
276
(6-cylinder models).
284
4-cylinder models6-cylinder models
For the first 8,000 miles (12,800 km)
after the Maintenance Required
Indicator is reset, it will come on for
two seconds when you turn the
ignition switch to ON (II).
Between 8,000 miles (12,800 km)
and 10,000 miles (16,000 km) this
indicator will light for two seconds
when you first turn the ignition
switch to ON (II), and then flash for
ten seconds.
If you exceed 10,000 miles (16,000
km) without having the scheduled
maintenance performed, this
indicator will remain on as a constant
reminder.
For the first 6,000 miles (9,600 km)
after the Maintenance Required
Indicator is reset, it will come on for
two seconds when you turn the
ignition switch to ON (II).
Between 6,000 miles (9,600 km) and
7,500 miles (12,000 km) this
indicator will light for two seconds
when you first turn the ignition
switch to ON (II), and then flash for
ten seconds.
If you exceed 7,500 miles (12,000
km) without having the scheduled
maintenance performed, this
indicator will remain on as a constant
reminder.
Instruments and Cont rols
CONTINUED
71
Gauges
Main Menu
Table of Content
Your dealer will reset this indicator
after completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Honda dealer, reset the indicator as
follows.
SELECT/RESET KNOB
Turn of f the engine.
1.
Press and hold the Select/Reset
2.
knob in the instrument panel, then
turn the ignition switch ON (II).
Hold the knob for approximately
3.
ten seconds until the indicator
resets.
72
Instruments and Cont rols
Controls Near the Steering Wheel
Main Menu
Table of Content
Thetwoleversonthesteering
column contain controls for driving
features you use most often. The left
lever controls the turn signals,
headlights, and high beams. The
right lever controls the windshield
washers and wipers.
The controls under the left air vent
are for the moonroof and the
Traction Control System.
The steering wheel adjustment lever
on the underside of the steering
column allows you to tilt and
telescope the steering wheel.
*
To use the horn, press the pad
around the ‘‘H’’ logo.
INSTRUMENT PANEL
BRIGHTNESS
(P.76)
*
HEADLIGHTS/
TURN SIGNALS
(P.74/77)
REMOTE
AUDIO
CONTROLS
(P.211)
MOONROOF
SWITCH
(P.108)
TRACTION CONTROL
SYSTEM ON/OFF
SWITCH
(P.259)
EX-V6 model without navigation system is shown.
HORN
TILT/TELESCOPIC
ADJUSTMENT
WINDSHIELD
WIPERS/WASHERS
(P.77, 79)
CRUISE
CONTROLS
(P.214)(P.80)
HAZARD
WARNING
LIGHTS
(P.79)
REAR WINDOW
DEFOGGER
(P.79)
Instruments and Cont rols
73
Controls Near the Steering Wheel
Main Menu
Table of Content
Headlights
The rotating switch on the left lever
controls the lights. Turning this
switch to the ‘‘’’ position turns
on the parking lights, taillights, and
rear license plate lights. Turning the
switch to the ‘‘’’ position turns
on the headlights.
74
Instruments and Cont rols
If you leave the lights on with the
ignition switch in ACCESSORY (I)
or LOCK (0), you will hear a
reminder chime when you open the
driver’s door.
When the light switch is in either of
these positions, the Lights On
indicator comes on as a reminder.
To change from low beams to high
beams, push the turn signal lever
forward until you hear a click. The
blue high beam indicator will light
(see page). To return to low
67
beams, pull the turn signal lever
back.
Controls Near the Steering Wheel
Main Menu
Table of Content
To flash the high beams, pull the
turn signal lever back lightly, then
release it. The high beams will come
onand go off.
The high beams will stay on for as
long as you hold the lever back, no
matter what position the headlight
switch is in.
Automatic Lighting Off Feature
The Automatic Lighting Off f eature
turns off the headlights, parking
lights, taillights and license plate
lights within 15 seconds of removing
the key from the ignition switch and
closing the driver’s door.
This feature activates if you leave
the headlight switch in the ‘‘’’
or ‘‘’’ position, remove the key,
open, then close the driver’s door.
If you remove the key from the
ignition switch with the headlight
switch on, but do not open the door
and get out, the lights will turn off
after ten minutes.
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights-on
reminder chime.
Instruments and Cont rols
75
Controls Near the Steering Wheel
Main Menu
Table of Content
(Canadian Models)
With the headlight switch off, the
high beam headlights and the high
beam indicator come on with
reduced brightness when you turn
the ignition switch to ON (II) and
release the parking brake. They
remain on until you turn the ignition
off, even if you set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
76
Instruments and Cont rols
Instrument Panel BrightnessDaytime Running Lights
SELECT/RESET KNOB
The Select/Reset knob on the
instrument panel controls the
brightness of the instrument panel
lights. Turn the knob to adjust the
brightness.
The instrument panel will illuminate
with reduced brightness when you
unlock and open the driver’s door.
The brightness will increase slightly
when you insert the key in the
ignitionswitch,thengotonormal
brightness when you turn the
ignition switch to ON (II).
If you do not insert the key in the
ignition switch after opening the
driver’s door, the illumination turns
off in about 30 seconds after closing
that door.
If you insert the key but do not turn
the ignition switch to ON (II), the
illumination turns off in about 10
seconds.
To reduce glare at night, the instrument panel illumination dims when
you turn the light switch toor
. Turning the Select/Reset
knob fully to the right until you hear
a click will cancel the reduced brightness.
Controls Near the Steering Wheel
Main Menu
Table of Content
Turn SignalsWindshield Wipers
To signal a lane change, push lightly
on the turn signal lever in the proper
direction and hold it. The lever will
return to the center position as soon
as you release it.
TURN SIGNAL LEVER
Signal a turn or lane change with this
lever. Push down on the lever to
signal a left turn, and up to signal a
right turn. If you push it up or down
all the way, the turn signal continues
to blink even when you release the
lever. It shuts off automatically as
you complete the turn.
This lever controls the windshield
wipers and washers. It has five
positions:
MIST: mist
OFF: off
INT: intermittent
LO: low speed
HI: high speed
To select a position, push the lever
up or down.
CONTINUED
Instruments and Cont rols
77
Controls Near the Steering Wheel
Main Menu
Table of Content
In intermittent, the wipers operate
every few seconds. The sweep
interval will change slightly with
speed; getting shorter as you drive
faster. While the car is stopped and
in gear, the wipers sweep the
windshield whenever you remove
your foot from the brake pedal. In
low speed and high speed, the wipers
run continuously.
78
Instruments and Cont rols
You can vary how often the wipers
sweep the windshield by turning the
INT TIME ring on the lever.
If you turn the INT TIME ring to the
shortest delay, the wipers will
change from intermittent to low
speed operation when vehicle speed
exceeds 12 mph (20 km/h).
To operate the wipers in mist mode,
push the control lever up from the
OFF position. The wipers run at high
speed until you release the lever.
This gives you a quick way to clear
the windshield.
To clean the windshield, pull back on
the wiper control lever. The washers
spray until you release the lever. The
wipers run at low speed while you’re
pulling the lever, then complete one
more sweep of the windshield after
you release it.
Push the button between the center
vents to turn on the hazard warning
lights (four-way f lashers). This
causes all four outside turn signals
and both turn indicators in the
instrument panel to f lash. Use the
hazard warning lights if you need to
park in a dangerous area near heavy
traf fic, or if your car is disabled.
The rear window defogger will clear
fog, frost, and thin ice from the
window. Push the defogger button to
turn it on and off. The light above/in
the button lights to show the
defogger is on. It also shuts off when
you turn off the ignition. You have to
turn it on again when you restart the
car.
CONTINUED
Instruments and Cont rols
79
Controls Near the Steering Wheel
Main Menu
Table of Content
Auto A/C type shown
Make sure the rear window is clear
and you have good visibility before
starting to drive.
Cars with navigation system
The defogger and antenna wires on
the inside of the rear window can be
accidentally damaged. When
cleaning the glass, always wipe side
to side.
Steering Wheel Adjustment
See pagefor important safety
information about how to properly
position the steering wheel.
18
Make any steering wheel adjustment
before you start driving.
Adjusting the steering wheel
position while driving may
cause you to lose control of the
car and be seriously injured in a
crash.
Adjust the steering wheel only
when the car is stopped.
80
Instruments and Cont rols
To adjust the steering wheel:
Main Menu
Table of Content
Insert the key in the ignition
1.
switch, and unlock the steering
column.
Push the lever under the steering
2.
column all the way down.
Move the steering wheel up or
3.
down, and in or out to the desired
position, making sure the wheel
points toward your chest, not
toward your face. Make sure you
can see the instrument panel
gauges and the indicator lights.
Push the lever up to lock the
4.
steering wheel in that position.
Make sure you have securely
5.
locked the steering wheel in place
by trying to move it up, down, in,
and out.
Controls Near the Steering Wheel
Instruments and Cont rols
81
Keys and Locks
Main Menu
Table of Content
Keys
KEY
NUMBER
TAG
MASTER
KEY WITH
REMOTE
TRANSMITTER
Your car comes with two master
keys and a valet key.
The master key fits all the locks on
your car:
• Ignition
• Driver’s door
•Glovebox
• Trunk release handle
• Rear seat trunk access
82
Instruments and Cont rols
VALET KEY
(LIGHT GREY)
The valet key works only in the
ignition and the driver’s door lock.
You can keep the trunk release
handle, rear seat trunk access, and
glove box locked when you leave
your car and the valet key at a
parking facility.
Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Keep
the tag stored in a safe place. If you
need to replace a key, use only
Honda-approved key blanks.
These keys contain electronic
circuits that are activated by the
Immobilizer System. They will not
work to start the engine if the
circuits are damaged.
Protect the keys from direct
sunlight, high temperature, and
high humidity.
Donotdropthekeysorsetheavy
objects on them.
Keep the keys away from liquids.
If they get wet, dry them
immediately with a soft cloth.
Remote Transmitter
Your car also comes with two remote
transmitters built into the master
keys; see pagefor an explanation
87
of the remote transmitter operation.
Keys and Locks
Main Menu
Table of Content
Immobilizer System
The Immobilizer System protects
your car f rom theft. A properlycoded master or valet key must be
used in the ignition switch for the
engine to start. If an improperlycoded key (or other device) is used,
the engine’s fuel system is disabled.
When you turn the ignition switch to
ON (II), the Immobilizer System
indicator should come on for a few
seconds, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to
LOCK (0), remove the key, reinsert
it, and turn the switch to ON (II)
again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object is near the
ignition switch when you insert the
key. To make sure the system
recognizes the key code:
Do not keep other immobilizer
keys on the same key ring.
Use a plastic or leather key fob,
not metal.
Keep other keys away from your
car’s key and the ignition switch
while trying to start the engine.
If the system repeatedly does not
recognize the coding of your key,
contact your Honda dealer.
The Immobilizer System indicator
will also blink several times when
you turn the ignition switch from ON
(II) to ACCESSORY (I) or LOCK (0).
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your car undriveable.
If you have lost your key and you
cannot start the engine, contact your
Honda dealer.
CONTINUED
Instruments and Cont rols
83
Keys and Locks
Main Menu
Table of Content
As required by the FCC:
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmf ul interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s
authority to operate the equipment.
This device complies with Industry
Canada Standard RSS-210.
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference that may cause
undesired operation of the device.
84
Instruments and Cont rols
The ignition switch is on the right
side of the steering column. It has
four positions:
•LOCK(0)
• ACCESSORY (I)
• ON (II)
• START (III)
LOCK (0)Ignition Switch
− You can insert or
remove the key only in this position.
To switch from ACCESSORY to
LOCK, you must push the key in
slightly as you turn it. If your car has
an automatic transmission, the shift
lever must also be in Park. The antitheft lock will lock the steering
column when you remove the key.
If the front wheels are turned, the
anti-theft lock may sometimes make
it difficult to turn the key from
LOCK to ACCESSORY. Firmly turn
the steering wheel to the left or to
the right as you turn the key.
Keys and Locks
Main Menu
Table of Content
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control.
Remove the key from the
ignition switch only when
parked.
−
ACCESSORY (I)
In this position,
you can operate the audio system
and the accessory power sockets.
−
ON (II)
This is the normal key
position when driving. All features
and accessories on the car are usable.
Several of the lights on the instrument panel come on as a test when
you turn the ignition switch from
ACCESSORY to ON.
−
START (III)
Use this position
only to start the engine. The switch
returns to ON (II) when you let go of
the key.
The engine will not start if the
Immobilizer System does not
recognize the key’s coding (see page
).
83
You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
the driver’s door. Remove the key to
turn off the beeper.
Instruments and Cont rols
85
Keys and Locks
Main Menu
Table of Content
Power Door Locks
MASTER DOOR LOCK SWITCH
Each door has a master door lock
switch. Either switch locks and
unlocks both doors. Push the top of
the switch to lock both doors; push
the bottom to unlock them.
86
Instruments and Cont rols
LOCK TAB
Each door has a lock tab at the top of
the door. When you push down the
lock tab on the driver’s door, both
doors lock. Pulling up the lock tab on
the driver’s door only unlocks that
door. The lock tab on the passenger’s
door only locks and unlocks that
door.
To lock the passenger’s door when
getting out of the car, push the lock
tab down and close the door. To lock
the driver’s door, remove the key
from the ignition switch and push
the lock tab down or push the top of
the master switch, then close the
door.
Both doors can be locked from the
outsidebyusingthekeyinthe
driver’s door. To unlock just the
driver’s door, turn the key and
releaseit.If youturnthekeyagain,
both doors will unlock.
Youcanopenorclosethewindows
by using the key in the driver’s door
(see page).106
Keys and Locks
Main Menu
Table of Content
Lockout Prevention
If you forget and leave the key in the
ignition switch, Lockout Prevention
will not allow you to lock the driver’s
door. With the driver’s door open
andthekeyintheignition,both
master door lock switches are
disabled. However, if the driver’s
door is not open, the master door
lock switches are not disabled.
Pushing the top of the switch on the
open passenger’s door will lock both
doors. If you try to lock an open
driver’s door by pushing down the
lock tab, the tabs on both doors pop
up. Pushing down the lock tab on the
passenger’s door only locks that door.
Remote Transmitter
UNLOCK
BUTTON
PANIC
BUTTON
LOCK
BUTTON
LED
TRUNK
RELEASE
BUTTON
You can lock and unlock your car
with the remote transmitter. When
you push the LOCK button, both
doors lock. The parking lights, side
marker lights, taillights and lights on
indicator flash once.
When you push the LOCK button a
second time within 5 seconds after
you have locked the doors, you will
hear a beep to verify that the doors
are locked and (if equipped) that the
security system has set.
When you push the UNLOCK button
once, only the driver’s door unlocks.
The passenger’s door unlocks when
you push the button a second time.
The parking lights, side marker
lights, taillights and lights on
indicator f lash twice each time you
push the button.
You can also open both power
windows from outside the car with
theremotetransmitter(seepage
).106
CONTINUED
Instruments and Cont rols
87
Keys and Locks
Main Menu
Table of Content
The ceiling light (if the ceiling light
switch is in the center position) and
the spotlights (if the switch is in the
Door position) will come on when
you press the UNLOCK button. If
you do not open either door, the
lights stay on for about 30 seconds,
then fade out. If you relock the doors
with the remote transmitter before
30 seconds have elapsed, the lights
will go off immediately.
You cannot lock the doors with the
remote transmitter if either door is
not fully closed or the key is in the
ignition switch. You cannot unlock
the doors with the key in the ignition
switch.
88
Instruments and Cont rols
If you unlock the doors with the
remote transmitter, but do not open
either door within 30 seconds, the
doors automatically relock and the
security system sets (except for
4-cylinder LX model).
To open the trunk, push the Trunk
Release button for approximately
one second.
The trunk will not open if the key is
in the ignition switch.
Panic Mode
Panic mode allows you to remotely
activate your car’s horn and exterior
lights to attract attention. The horn
sounds and the exterior lights flash
for about 30 seconds. To activate
panic mode, press and hold the
PANIC button for about two seconds.
To cancel Panic mode before 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.
Replacing the Battery
Main Menu
Table of Content
When the remote transmitter’s
battery begins to get weak, it may
take several pushes on the button to
lock or unlock the doors, and the
LED will not light. Replace the
battery as soon as possible.
Battery type: CR1616
Keys and Locks
BATTERY
SCREW
To replace the battery:
Remove the screw at the base of
1.
the transmitter with a small
Phillips-head screwdriver.
Separate the transmitter by prying
2.
its middle seam with your
fingernail.
TAB
Inside the transmitter, separate
3.
the inner cover from the keypad
by releasing the two tabs on the
cover.
CONTINUED
Instruments and Cont rols
89
Keys and Locks
Main Menu
Table of Content
Remove the old battery from the
4.
back of the inner cover, and note
the polarity. Make sure the
polarity of the new battery is the
same (side facing down), then
insert it into the back of the cover.
Install the parts in reverse order.
5.
90
Instruments and Cont rols
+
As required by the FCC:
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmf ul interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s
authority to operate the equipment.
This device complies with Industry
Canada Standard RSS-210.
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference that may cause
undesired operation of the device.
Transmitter Care
Avoid severe shock to the transmitter, such as dropping or throwing
it. Also, protect it from extreme hot
or cold temperatures.
Clean the transmitter case with a
soft cloth. Do not use strong
cleaners or solvents that could harm
the case. Immersing the transmitter
in any liquid will harm the transmitter and cause it to not function
properly.
If you lose a transmitter, you will
need to have the replacement
programmed to your car’s system by
your Honda dealer. Any other
transmitters you have will also need
to be reprogrammed.
Keys and Locks
Main Menu
Table of Content
Trunk
TRUNK RELEASE HANDLE
Youcanopenthetrunkintwoways:
Pull the trunk release handle to
the left of the driver’s seat.
Press and hold the trunk release
button on the remote transmitter.
Pull
To close the trunk, press down on
the trunk lid.
See pagefor cargo loading and
234
weight limit information. Keep the
trunk lid closed at all times while
driving to avoid damaging the lid,
and to prevent exhaust gas from
getting into the interior. See
Monoxide Hazard
on page.
Carbon
56
MASTER
KEY
To protect items in the trunk when
you need to give the key to someone
else:
Lock the trunk release handle
1.
with the master key.
Give the person the valet key.
2.
Instruments and Cont rols
91
Keys and Locks
Main Menu
Table of Content
Emergency Trunk Opener
As a safety feature, your car has a
release lever on the trunk latch so
the trunk can be opened from the
inside.
92
Instruments and Cont rols
To open the trunk, push the release
lever to the left.
Parents should decide if their
children should be shown how to use
this feature.
For more inf ormation about child
safety, see page.25
Glove Box
Main Menu
Table of Content
GLOVE BOX
Open the glove box by pulling the
handle to the left. Close it with a firm
push. Lock or unlock the glove box
with the master key.
The glove box light comes on when
the parking lights are on.
Keys and Locks
An open glove box can cause
serious injury to your passenger
inacrash,evenifthe
passenger is wearing the seat
belt.
Always keep the glove box
closed while driving.
Instruments and Cont rols
93
Seat Adjustments
Main Menu
Table of Content
All V6 models, and the 4-cylinder EX
model with leather interior have a
power adjustable driver’s seat.
The 4-cylinder EX model without
leather interior has a power seat
bottom height adjustment. All other
driver’s seat adjustments in this
model are manual.
The 4-cylinder LX model has manual
driver’s seat adjustments (see next
column).
The front passenger’s seat in all
models adjusts manually.
94
Instruments and Cont rols
FrontSeatAdjustments
See pagesfor important safety
information and warnings about how to
properly position seats and seat-backs.
−
1415
Make all seat adjustments before
you start driving.
To adjust the seat forward and
backward, pull up on the bar under
the seat cushion’s front edge. Move
the seat to the desired position and
releasethebar.Trytomovetheseat
to make sure it is locked in position.
To change the angle of the seat-back,
pull up on the lever on the outside of
the seat bottom. Move the seat-back
to the desired position and release
the lever. Let the seat-back latch into
the new position.
Seat Adjustments
Main Menu
Table of Content
Driver’s Seat Manual Height
Adjustment
On 4-cylinder LX modelOn 4-cylinder EX model without leather
Make sure to pull the lever upward
or downward to its full range.
The height of your driver’s seat is
adjustable. To raise the seat bottom,
repeatedly pull up the lever on the
outside of the seat cushion. To lower
the seat, push down the lever
Driver’s Seat Power Height
Adjustment
interior
The height of your driver’s seat is
power adjustable. Pull up on the
switch to raise the seat. Push it down
to lower the seat.
repeatedly.
Make all seat adjustments before
Make all seat adjustments before
you start driving.
you start driving.
Instruments and Cont rols
95
Seat Adjustments
Main Menu
Table of Content
Driver’s Seat Power Adjustments
On all V6 models, and the 4-cylinder
EX model with leather interior
See pagesfor important safety
information and warnings about how to
properly position seats and seat-backs.
The two power seat adjustment
switches are on the outside edge of
the seat bottom. The horizontal
switch adjusts the seat bottom in
several directions. The short vertical
switch adjusts the seat-back angle.
You can adjust the seat with the
ignition switch in any position. Make
all seat adjustments before you start
driving.
−
1514
Push the horizontal switch forward
or backward to move the seat
forward or backward.
Pull up or push down on the front of
the switch to move the seat bottom’s
front edge up or down. Pull up or
push down on the rear of the switch
to move the rear of the seat bottom
up or down.
96
Instruments and Cont rols
Seat Adjustments
Main Menu
Table of Content
Driver’s Lumbar Support
Pull the center of the horizontal
switch up to raise the seat. Push it
down to lower the seat.
Adjust the seat-back angle by
pushing the rear switch in the
On all EX and EX-V6 models
direction you want to move.Vary the lumbar support by moving
the lever on the right side of the
seat-back. Move the lever forward to
increase support and backward to
decrease it.
Instruments and Cont rols
97
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.