Page 1
Auto Rewind Hose Reel
16mm x 25m High Flow Hose
Instruction Manual
25M High Flow Auto Rewind Hose Reel
Installation and Troubleshooting Guide
Page 2
Product Code: 1125H
Introduction
Thank you for purchasing this HOLMAN Auto Rewind Hose Reel. This product uses a 16mm
reinforced hose for added strength and durability, and includes a high ow adjustable nozzle.
For your information, please read these installation instructions before using the
Auto Rewind Hose Reel. Please keep all instructions and refer to them when necessary.
Glossary
Mounting Tube
Wall Plugs / Hexagonal Coach Bolts (included)
Coated Wall
Bracket
16mm
High Flow Hose
Adjustable High Flow Nozzle
Auto Rewind Hose Reel
Tap to Reel
Hose
Securing Pin
Page 3
Auto Rewind Hose Reel - Instruction Manual
Hose Reel Operating Features
1
2
Supplied with each hose reel is a strong
1
coated wall bracket and hose end plug
for convenient storage when not in use.
Lift the hose reel top cover for easy
access to either clean or replace your
2
hose. (20m & 30m replaceable only)
Page 4
Auto Rewind Hose Reel - Instruction Manual
Auto Rewind Hose Reel Installation
1
The Auto Rewind Hose Reel should be
1 2
installed nearest to your chosen water
source for convenience of use. Check
the tap to reel hose can reach the tap
prior to mounting the hose reel.
2
Take the coated mounting bracket and
place against either a wall or wooden post.
Mark the position of where you would like
the screws to be placed through the centre
of the bracket holes to prepare for drilling.
3
Take the wall plugs (supplied with the hose
3
It is recommended that you drill slightly undersize
as all materials have different properties and this will
ensure the wall plugs have a secure t. Please note
that if you are attaching your hose reel to a wooden
post, you will not require the wall plugs as the coach
bolts screw directly into wood.
As a guide only, the wall plugs for the 10m hose reel
are 7.7mm in diameter, suitable to hammer into a
8mm drilled hole, and the 20m/25m/30m wall plugs
are 11.7mm, suitable to hammer into an 12mm hole.
It is very important to use the correct size drill bit,
so a very secure t of the wall bracket is made before
installing the Auto Rewind Hose Reel.
When ready drill all four holes, then hammer the wall
plugs gently into your wall. (if attaching to a wall).
reel) and measure the correct drill bit width
to use.
Page 5
Auto Rewind Hose Reel - Instruction Manual
4
Place the bracket in position over
4 5
the four wall plugs and screw each
hexagonal coach bolt into your wall
or wooden post. Screw in each bolt
until all four have a secure hold on the
coated bracket against the surface,
making sure you slot the bracket down
over the bolts before tightening.
5
Take your Auto Rewind Hose Reel, and
remove the securing pin at the base of
the mounting tube. Remove the mounting
tube from the hose reel and slot the hose
reel inside the wall bracket, so the tting
tube hole lines up with the wall bracket
hole. Then replace the mounting tube into
its hole to hold the hose reel in place and
replace the securing pin into the base of the
mounting tube.
6
Connect the tap to reel hose, to the
6
garden tap.
7
7
You are now ready to use your
Auto Rewind Hose Reel.
Page 6
Troubleshooting - Hose Reel Not Retracting
Locking Bars Preventing Retraction
1
1
Locking bars in the CORRECT
position, clipped to the outer casing.
2
2
Locking bars in the WRONG position
laying on the hose. They will cause the
hose to jam as it extends or retracts.
3
3
Locking bars in the CORRECT
position, clipped to the outer casing.
4
4
Locking bars in the WRONG position.
The bars will catch on the reel &
prevent it from working correctly.
Page 7
i
Troubleshooting - Hose Reel Not Extending
Fully Retracted Hose Not Extending
1
1
If the hose isn’t extending properly,
this may be caused by the screws
securing the guide hole being too tight.
2
2
Slowly pull the hose to move the guide
hole away from the inside edge of the
hose unit for easier access.
3
3
Taking a cross head screw driver,
unscrew the 2 screws holding the
guide hole in place slighly, so the hose
moves freely as you extend it.
IMPORTANT NOTE:
This unit has a 16mm Hi-Flow
hose and comes fitted with
hose connections designed
specifically for this purpose.
A standard 12mm hose
connector will not fit.
Page 8
Troubleshooting - Hose Reel Not Retracting
Fully Extended Hose Not Retracting
1 2
If the hose retraction wheel is stuck
and the hose is fully extended, the
1
wheel still has movement past this
point. Grip the hose close to the guide
hole and gently pull.
The retraction wheel will give you
enough movement to unlock itself
2
before you slowly allow the auto
retraction wheel to wind the hose back
into the unit.
Auto Rewind Hose Reel - Warranty
Should you have any questions about this product or its operation please telephone
our customer service helpline on 1300 716 188.
Holman offer a 2 year replacement warranty from the original date of purchase.
To claim warranty the product must be returned with a copy of the original receipt.
We will honour all statutory guarantees that this product is of acceptable quality
(including that it is t for purpose).
HOLMAN INDUSTRIES
47 Walters Drive,
Osborne Park,
Western Australia 6017.
Tel: +61 8 9204 1011 Fax: +61 8 9204 1013
Web: www.holmanindustries.com.au
Loading...